Search Results (15)

To increase the use of agricultural residues, such as date palm fibers, for the sustainable reinforcement of biocomposites, this study investigated the incorporation of varying weight percentages of date palm microfibers (DPMF) ranging from 0 wt.% to 10 wt.% into polycaprolactone (PCL) matrix. Biocomposites were fabricated using a combination of compression molding and dry blending techniques with and without sodium hydroxide (NaOH) alkali treatment. The surface modification was found to increase the surface roughness of the fibers, removing impurities such as lignin, hemicellulose, and wax, while improving crystallinity, as evidenced by FTIR, XRD, TGA, and particle size analyses. Among the different biocomposites investigated, the results for 5 wt.% DPMF content biocomposites exhibited the highest tensile properties: approximately 20% increase in tensile strength and 164% increase in Young’s Modulus in comparison to neat PCL. The crystallinity of the matrix exhibited an increasing trend from approximately 39% for neat PCL to 43% for the 5 wt.% DPMF biocomposites. Furthermore, treated biocomposites demonstrated higher water-repellency behavior and improved thermal properties. Dynamic mechanical analysis (DMA) results indicated enhanced storage moduli for alkali-treated composites; at 35 °C, the storage modulus showed approximately 22% increase compared to the untreated DPMF biocomposites, reflecting improved stiffness and thermomechanical performances. This study highlights the potential of DPMF as an efficient, eco-friendly alternative to fossil-based conventional reinforcement for biocomposite materials’ potential for sustainable rigid packaging applications. Full article

A tremendous amount of waste black tea bags (BTBs) and date palm surface fibers (DPSFs), at the end of their life cycle, end up in landfills, leading to increased pollution and an increase in the negative impact on the environment. Therefore, this study aims to utilize these normally wasted materials efficiently by developing new composite materials for thermal insulation and sound absorption. Five insulation composite boards were developed, two were bound (BTB or DPSF with polyvinyl Acetate resin (PVA)) and three were hybrids (BTB, DPSF, and resin). In addition, the loose raw waste materials (BTB and DPSF) were tested separately with no binder. Thermal conductivity and sound absorption coefficients were determined for all boards. Thermal stability analysis was reported for the components of the tea bag (string, label, and bag) and one of the composite hybrid boards. Mechanical properties of the boards such as flexural strain, flexural stress, and flexural elastic modulus were determined for the bound and hybrid composites. The results showed that the thermal conductivity coefficients for all the hybrid composite sample boards are less than 0.07 at the ambient temperature of 24 °C and they were enhanced as the BTB ratio was reduced in the hybrid composite boards. The noise reduction coefficient for bound and all hybrid composite samples is greater than 0.37. The composite samples are thermally stable up to 291 °C. Most composite samples have a high flexure modulus between 4.3 MPa and 10.5 MPa. The tea bag raw materials and the composite samples have a low moisture content below 2.25%. These output results seem promising and encouraging using such developed sample boards as eco-friendly thermal insulation and sound absorption and competing with the synthetic ones developed from petrochemicals in building insulation. Moreover, returning these waste materials to circulation and producing new eco-friendly composites can reduce the number of landfills, the level of environmental pollution, and the use of synthetic materials made from fossil resources. Full article

New composites made of natural fiber polymers such as wasted date palm surface fiber (DPSF) and pineapple leaf fibers (PALFs) are developed in an attempt to lower the environmental impact worldwide and, at the same time, produce eco-friendly insulation materials. Composite samples of different compositions are obtained using wood adhesive as a binder. Seven samples are prepared: two for the loose natural polymers of PALF and DPSF, two for the composites bound by single materials of PALF and DPSF using wood adhesive as a binder, and three composites of both materials and the binder with different compositions. Sound absorption coefficients (SACs) are obtained for bound and hybrid composite samples for a wide range of frequencies. Flexural moment tests are determined for these composites. A thermogravimetric analysis test (TGA) and the moisture content are obtained for the natural polymers and composites. The results show that the average range of thermal conductivity coefficient is 0.042–0.06 W/(m K), 0.052–0.075 W/(m K), and 0.054–0.07 W/(m K) for the loose fiber polymers, bound composites, and hybrid composites, respectively. The bound composites of DPSF have a very good sound absorption coefficient (>0.5) for almost all frequencies greater than 300 Hz, followed by the hybrid composite ones for frequencies greater than 1000 Hz (SAC > 0.5). The loose fiber polymers of PALF are thermally stable up to 218 °C. Most bound and hybrid composites have a good flexure modulus (6.47–64.16 MPa) and flexure stress (0.43–1.67 Mpa). The loose fiber polymers and bound and hybrid composites have a low moisture content below 4%. These characteristics of the newly developed sustainable and biodegradable fiber polymers and their composites are considered promising thermal insulation and sound absorption materials in replacing synthetic and petrochemical insulation materials in buildings and other engineering applications. Full article

The pervasive challenge of heavy metal pollution in water necessitates urgent interventions to mitigate chromium contamination. It poses significant threats to human health, aquatic ecosystems, and the environment. This research delves into the potential of date palm waste as a precursor of adsorbent for extraction of chromium from contaminated water, underscoring its potential in heavy metal remediation. Date palm waste, traditionally regarded as agricultural waste, underwent modification employing N-(3-chloro-2-hydroxypropyl) trimethylammonium chloride resulting in quaternized date palm waste (QDPW) as a prospective adsorbent for chromium extraction. The characterization techniques, including FTIR, SEM/EDX, BET, XRD, TGA/DTA, and element analysis, were employed to examine the structural and surface properties of both DPW and QDPW fibers. Optimal chromium uptake was achieved at a solution pH 6.5 over two hours, with a peak removal efficiency of 88% and an adsorption capacity of 22.26 mg/g. The equilibrium isotherms studies are consistent with Langmuir, Redlich-Peterson, and Sips isotherms, presenting a coefficient of determination (R²) of 0.989, 0.981, and 0.983, respectively. Moreover, the pseudo-second-order model was mostly aligned with the kinetics data with R² value of 0.999. These findings showed that the quaternized date palm waste can be considered a good option to recycle the date palm waste and reduce the environmental threats in aqueous solution. Full article

The date palm tree is extensively cultivated in Middle Eastern countries such as Saudi Arabia, generating a large amount of waste in the form of leaves, seeds, and fibrous materials. This study examined the feasibility of using raw date palm fiber (RDPF) and NaOH chemically modified date palm fiber (NaOH–CMDPF) obtained from discarded agricultural waste for the removal of phenol in an aqueous environment. The adsorbent characterization was performed by using different techniques, i.e., particle size analysis; elemental analyzer (CHN); and BET, FTIR, and FESEM-EDX analysis. The FTIR analysis revealed the presence of various functional groups on the surface of the RDPF and NaOH–CMDPF. The results showed that chemical modification by NaOH increased the phenol adsorption capacity that was well-fitted by the Langmuir isotherm. Higher removal was obtained with NaOH–CMDPF (86%) than with the RDPF (81%). The RDPF and NaOH–CMDPF sorbents’ maximum (Q_m) adsorption capacities were more than 45.62 mg/g and 89.67 mg/g and were comparable to the sorption capacities of various other types of agricultural waste biomass reported in the literature. The kinetic studies confirmed that the adsorption of phenol followed the pseudo-second-order kinetic process. The present study concluded that the RDPF and NaOH–CMDPF were eco-friendly and cost-effective in promoting sustainable management and the reuse of the Kingdom’s lignocellulosic fiber waste material. Full article

Date palm fiber (DPF) has been reported to have many advantages when used in concrete, however, its major disadvantage is that it causes a reduction in compressive strength. In this research, powdered activated carbon (PAC) was added to cement in the DPF-reinforced concrete (DPFRC) to lessen the loss in strength. PAC has not been properly utilized as an additive in fiber reinforced concrete even though it has been reported to enhance the properties of cementitious composites. Response surface methodology (RSM) has also been utilized for experimental design, model development, results analysis, and optimization. The variables were DPF and PAC as additions each at proportions of 0%, 1%, 2%, and 3% by weight of cement. Slump, fresh density, mechanical strengths, and water absorption were the responses that were considered. From the results, both DPF and PAC decreased the workability of the concrete. DPF addition improved the splitting tensile and flexural strengths and reduced the compressive strength, and up to 2 wt% PAC addition enhanced the concrete’s strength and lowered the water absorption. The proposed models using RSM were extremely significant and have excellent predictive power for the concrete’s aforementioned properties. Each of the models was further validated experimentally and was found to have an average error of less than 5.5%. According to the results of the optimization, the optimal mix of 0.93 wt% DPF and 0.37 wt% PAC as cement additives resulted in the best properties of the DPFRC in terms of workability, strength, and water absorption. The optimization’s outcome received a 91% desirability rating. The addition of 1% PAC increased the 28-day compressive strength of the DPFRC containing 0%, 1% and 2% DPF by 9.67%, 11.13% and 5.5% respectively. Similarly, 1% PAC addition enhanced the 28-day split tensile strength of the DPFRC containing 0%, 1% and 2% by 8.54%, 11.08% and 19.3% respectively. Likewise, the 28-day flexural strength of DPFRC containing 0%, 1%, 2% and 3% improved by 8.3%, 11.15%, 18.7% and 6.73% respectively with the addition of 1% PAC. Lastly, 1% PAC addition led to a reduction in the water absorption of DPFRC containing 0% and 1% DPF by 17.93% and 12.2% respectively. Full article

Date palm fiber (DPF) is one of the abundant solid waste materials in the agriculture sector in Saudi Arabia, and it is gaining great attraction due to its advantages compared to synthetic and other natural fibers. For proper utilization of DPF in cementitious composites, its performance under high temperatures needs to be understood. This is because DPF is a cellulose-based agricultural fiber material and is expected to degrade when subjected to high temperatures. This will cause a significant loss in strength and structural integrity of the composites. The use of Pozzolanic materials has been reported to reduce the loss in mechanical properties of cementitious composites under high temperatures. With powdered activated carbon (PAC) being a low-cost material compared to other Pozzolanic materials, this study utilized PAC as an additive to the DPF-reinforced concrete to mitigate its loss in mechanical strength when exposed to elevated temperature. The experiment was designed using response surface methodology (RSM), which was used to construct mathematical models for estimating the strengths of the concrete exposed to high temperatures. The DPF was added at proportions of 1%, 2%, and 3% by weight of cement. Similarly, the PAC was added at 1%, 2%, and 3% by weight of cement to the concrete. The concrete was subjected to elevated temperatures of 300 °C, 600 °C, and 900 °C for a 2 h exposure period. The degradation of the concrete in terms of mass loss and the compressive strength of the concrete after heating were measured. DPF in the concrete led to an escalation in weight loss and reduction in strength, which was more pronounced at a temperature of 600 °C and above. The addition of PAC resulted in an enhancement in the strengths of the concrete containing up to 2% DPF at 300 °C, while at 600 °C the improvement was minimal. The models developed for predicting the mass loss and strengths of the DPF-reinforced concrete under high temperatures were statistically significant with a high correlation degree. Based on the optimization results, DPF-reinforced concrete produced with 1% DPF, and 2.27% PAC as additives and subjected to a temperature of 300 °C for 2 h yielded the lowest mass loss of 2.05%, highest residual compressive strength and relative strength of 45.85 MPa and 106.7% respectively. Full article

Date palm fruit (Phoenix dactylifera: Arecaceae) is rich in essential nutrients and possesses several pharmacological and medicinal activities. The current study aimed to optimize a water bath-assisted extraction method for two cultivars of date palm fruits, Anbara (An) and Reziz (Rz), and investigated the protective effect of the optimized date palm fruit extract against CCl₄-induced liver toxicity in relation to oxidative stress, inflammation, apoptosis, and DNA integrity. The optimization process of two date palm fruit cultivars was applied, using response surface methodology through adjusting three “factors”; time, temperature, and rotation, to allow maximum contents of total phenolic (TPC), total flavonoid (TFC), reducing power (FRAP) and scavenging activity (ABTS) of the extract “responses”. Extraction factors’ application significantly enhanced TPC, TFC, FRAP, and ABTS responses by 1.30, 1.23, 3.03, and 2.06-fold, respectively in An and 2.18, 1.71, 1.11, and 2.62-fold, respectively in Rz, in relation to the convectional water extraction. Furthermore, co-administered CCl₄ with An or Rz optimized extracts enhanced body weight gain, amended hepatic architecture, and diminished collagen fiber accumulation. Furthermore, An or Rz extracts reduced liver enzymes, hydroxyproline, alpha-fetoprotein (AFP), MDA, inflammatory cytokine (TNF-α, NF-κB) levels, and DNA fragmentation, while increasing deteriorated adiponectin (ADP) and antioxidant enzyme (GSH, GPX, NO, and IFN-γ) levels, relative to CCl₄-administered animals. The protective effects of An or Rz-optimized extracts were also evidenced by suppressing hepatic fibrosis and improving liver function and structure via modulating oxidative stress, inflammation, and apoptosis, in CCl₄-induced hepatic damage. Hence, the optimized extraction process for the two date palm fruits resulted in extracts which are rich in phenolic and flavonoid contents and with an elevated antioxidant power. The presence of these rich extracts could help to explain their proven hepatoprotective activity against CCl₄-induced liver toxicity. Full article

Due to its availability and affordable processing, date palm fiber (DPF) is among the natural and sustainable fibers used in cementitious composites. Furthermore, DPF is an agricultural, organic, and fibrous material that when subjected to higher temperature can easily degrade and cause reduction in strength. Therefore, the influence of elevated temperatures on the unit weight and strengths of DPF-reinforced concrete needs to be examined. Under this investigation, DPF is used in proportions of 0–3% weight of binder to produce a DPF-reinforced concrete. Silica fume was utilized as a supplemental cementitious material (SCM) in various amounts of 0%, 5%, 10%, and 15% by weight to enhance the heat resistance of the DPF-reinforced concrete. The concrete was then heated to various elevated temperatures for an hour at 200 °C, 400 °C, 600 °C, and 800 °C. After being exposed to high temperatures, the weight loss and the compressive and relative strengths were examined. The weight loss of DPF-reinforced concrete escalated with increments in temperature and DPF content. The compressive and relative strengths of the concrete improved when heated up to 400 °C, irrespective of the DPF and silica fume contents. The heat resistance of the concrete was enhanced with the replacement of up to 10% cement with silica fume when heated to a temperature up to 400 °C, where there were enhancements in compressive and relative strengths. However, at 800 °C, silica fume caused a significant decline in strength. The developed models for predicting the weight loss and the compressive and relative strengths of the DPF-reinforced concrete under high temperature using RSM have a very high degree of correlation and predictability. The models were said to have an average error of less than 6% when validated experimentally. The optimum DPF-reinforced concrete mix under high temperature was achieved by adding 1% DPF by weight of binder materials, replacing 12.14% of the cement using silica fume, and subjecting the concrete to a temperature of 317 °C. The optimization result has a very high desirability of 91.3%. Full article

This study reports a facile approach for preparing low-cost, eco-friendly nanocomposites of ZnO nanoparticles (NPs) and date palm tree fiber (DPF) as a biomass sorbent. The hypothesis of this research work is the formation of an outstanding adsorbent based on the date palm fiber and ZnO nanoparticles. ZnO NP/DPF nanocomposites were synthesized by mixing the synthesized ZnO NPs and DPF in different mass ratios and evaluating their efficacy in adsorbing Pb²⁺ from aqueous solutions. The structure and surface morphology of the developed ZnO NP/DPF nanocomposite were critically characterized by XRD, FESEM, and TEM techniques. Compared to ZnO NPs, the ZnO NP/DPF nanocomposites displayed significantly enhanced Pb²⁺ uptake. Pb²⁺ adsorption was confirmed via various isotherm and kinetic models and thermodynamics. The computed Langmuir sorption capacity $(q_m$) was found to be 88.76 mg/g (R² > 0.998), and the pseudo-second-order R² > 0.999 model was most appropriate for describing Pb²⁺ adsorption. Impregnating the biomass with ZnO NPs enhanced the spontaneity of the process, and the value (−56.55 kJ/mol) of $\Delta H$ displayed the exothermic characteristics of Pb²⁺ retention. Only the loaded ZnO NP/DPF achieved the removal of a high percentage (84.92%) of Pb²⁺ from the environmental water sample (seawater). This finding suggests the use of ZnO NP/DPF nanocomposites for removing heavy metals from environmental water samples to purify the samples. Full article

Some of the major challenges of the twenty-first century include the continued increase in energy consumption and environmental pollution. One approach to overcoming these challenges is to increase the use of waste materials and environmentally friendly manufacturing methods. The high energy consumption in the building sector contributes significantly to global climatic changes. Here, by using date palm surface fibers, a high-performance green insulation material was developed via a simple technique that did not rely on any toxic ingredients. Polyvinyl alcohol (PVA) was used as a binding agent. Four insulation samples were made, each with a different density within the range of 203 to 254 kg/m³. Thermal conductivity and thermal diffusivity values for these four green insulators were 0.038–0.051 $\mathrm{W}/\left(\mathrm{m}·\mathrm{K}\right)$ and 0.137–0.147 mm²/s, respectively. Thermal transmittance (U-value) of the four insulation composites was between 3.8–5.1 $\mathrm{W}/{\mathrm{m}}^2·\mathrm{K}$, which was in good comparison to other insulators of similar thickness. Thermogravimetric analysis (TGA) showed that insulating sample have excellent thermal stability, with an initial degradation temperature of 282 °C, at which just 6% of its original weight is lost. Activation energy ($E_a$) analysis revealed the fire-retardancy and weakened combustion characteristics for the prepared insulation composite. According to differential scanning calorimetry (DSC) measurements, the insulating sample has a melting point of 225 °C, which is extremely close to the melting point of the binder. The fiber-based insulating material’s composition was confirmed by using Fourier transform infrared spectroscopy (FTIR). The ultimate tensile range of the insulation material is 6.9–10 MPa, being a reasonable range. Our study’s findings suggest that developing insulation materials from date palm waste is a promising technique for developing green and low-cost alternatives to petroleum-based high-cost and toxic insulating materials. These insulation composites can be installed in building envelopes during construction. Full article

Among the critical issues dictating bio-composite performance is the interfacial bonding between the natural fibers and polymer matrix. In this regard, this article presents new synthesis routes comprising the treatment and functionalization of both date palm powder (DPP) filler and a polypropylene (PP) matrix to enhance filler–polymer adhesion in the newly developed bio-composites. Specifically, four bio-composite forms are considered: untreated DPP filled PP (DPP-UT/PP), treated DPP filled PP (DPP-T/PP), treated DPP filled functionalized PP using 2-isocyanatoethyl methacrylate (DPP-T/PP-g-IEM), and treated and functionalized DPP using 4-toluenesulfonyl chloride filled functionalized PP using 2-acrylamide ((DPP-T)-g-TsCl/PP-g-AcAm). The functional groups created on the surface of synthesized PP-g-IEM react with activated hydroxyl groups attached to the filler, resulting in chemical crosslinking between both components. Similarly, the reaction of TsCl with NH₂ chemical groups residing on the mating surfaces of the filler and polymer generates an amide bond in the interface region. Fourier transform infrared spectroscopy (FTIR) is used to confirm the successful coupling between the filler and polypropylene matrix after applying the treatment and functionalization schemes. Owing to the introduced crosslinking, the DPP-T/PP-g-IEM bio-composite exhibits the best mechanical properties as compared to the neat polymer, unfunctionalized polymer-based bio-composite, and (DPP-T)-g-TsCl/PP-g-AcAm counterpart. The applied compatibilizers assist in reducing the water uptake of the manufactured bio-composites, increasing their durability. Full article

Cellulosic fibers from date palm are among the most promising lignocellulose feedstock for biorefinery purposes. The world production is between 1.9 and 2.4 million t/year. Initially, a pretreatment with dilute-sulphuric acid of these fibers was performed using a response surface methodology, with temperature and process time as factors. The aim is to produce bioethanol from young and old fibers from date palm, Phoenix dactylifera L. Optimal thermochemical pretreatment conditions for both fibers palms were 220 °C in hydrothermal conditions (without acid); in these conditions pretreated young fibers presented a maximum content in holocelluloses of 45.18% and old fibers 61.97%. Subsequently, during the enzymatic hydrolysis a maximum yield of total reducing sugars (TRS) was reached, 46.32 g/100 g for pretreated dry young fibers and 48.54 g/100 g for pretreated dry old fibers. After enzymatic saccharification, hydrolysates were fermented by Pachysolen tannophilus (ATCC 32691) to ethanol, reaching yields (Y_E/TRS) of 37.94 g ethanol/100 g of TRS for young fibers and 35.84 g ethanol/100 g of TRS for old fibers. Globally, considering the full process, in the fermentation of the hydrolysates, a yield (Y_E) of 10.64 g ethanol/100 g of dry young fibers and 10.88 g ethanol/100 g of dry old fibers was reached. Full article

In this work, date palm waste (DPW) stemming from the annual pruning of date palm was used as reinforcing filler in polypropylene (PP) matrix at 40% w/w. Three pre-treatment routes were performed for the DPW, namely (i) defibration, (ii) soft alkali treatment, and (iii) enzymatic treatment, to obtain date palm fibers (DPF) and to investigate the effect of each process on their chemical composition, which will ultimately affect the mechanical properties of the resulting composites. The enzymatic and alkali treatment, combined with maleated polypropylene (MAPP) as a coupling agent, resulted in a composite with higher strength and stiffness than the neat PP. The differences in the reinforcing effect were explained by the change in the morphology of DPF and their chemical surface composition according to the selected treatment of DPW. Enzymatic treatment maximized the tensile strength of the compound as a consequence of an improvement in the interfacial shear strength and the intrinsic resistance of the fibers. Full article

The present study deals with the fabrication of epoxy composites reinforced with 50 wt% of date palm leaf sheath (G), palm tree trunk (L), fruit bunch stalk (AA), and leaf stalk (A) as filler by the hand lay-up technique. The developed composites were characterized and compared in terms of mechanical, physical and morphological properties. Mechanical tests revealed that the addition of AA improves tensile (20.60–40.12 MPa), impact strength (45.71–99.45 J/m), flexural strength (32.11–110.16 MPa) and density (1.13–1.90 g/cm³). The water absorption and thickness swelling values observed in this study were higher for AA/epoxy composite, revealing its higher cellulosic content, compared to the other composite materials. The examination of fiber pull-out, matrix cracks, and fiber dislocations in the microstructure and fractured surface morphology of the developed materials confirmed the trends for mechanical properties. Overall, from results analysis it can be concluded that reinforcing epoxy matrix with AA filler effectively improves the properties of the developed composite materials. Thus, date palm fruit bunch stalk filler might be considered as a sustainable and green promising reinforcing material similarly to other natural fibers and can be used for diverse commercial, structural, and nonstructural applications requiring high mechanical resistance. Full article