Search Results (97)

Liquid crystal elastomers (LCEs), as a class of smart materials, have attracted significant attention across soft robotics, biomedical engineering, and intelligent devices because of their unique capabilities to undergo large, reversible, and anisotropic deformations under external stimuli. Over the years, fabrication methods have advanced from conventional molding and thin-film processing to additive manufacturing, with 4D printing emerging as a transformative approach by enabling time-dependent, programmable shape transformations. Among the available methods, direct ink writing (DIW) and vat photopolymerization are most widely adopted, with ink chemistry, rheology, curing, and printing parameters directly governing mesogen alignment and actuation performance. Recent advances in LCE actuators have demonstrated diverse functionalities in soft robotics, including bending, crawling, gripping, and sequential actuation, while biomedical applications span adaptive tissue scaffolds, wearable sensors, and patient-specific implants. This review discusses the conceptual distinction between 3D and 4D printing, compares different additive manufacturing techniques for LCE, and highlights emerging applications in the field of soft robotics and biomedical technologies. Despite rapid progress in LCE, challenges remain in biocompatibility, long-term durability and manufacturing scalability. Overall, innovations in 4D printing of LCEs underscores both the promise and the challenges of these materials, pointing toward their transformative role in enabling next-generation soft robotic and biomedical technologies. Full article

The dehydrogenation of cyclohexane is of vital importance for the production of Nylon-6 and Nylon-66, as it enhances atom utilization efficiency. Ca-doped platinum catalysts have been employed in alkane dehydrogenation due to their ability to selectively activate C–H bonds while minimizing C–C bond cleavage. However, owing to their limited selectivity toward cyclohexene, Pt-Ca/Al₂O₃ catalysts have not been widely adopted in the field of partial dehydrogenation to alkenes. In this work, Al₂O₃ supports are fabricated using the direct ink writing (DIW) 3D printing technique, incorporating designed channels. After impregnation and calcination at 550 °C, the distribution of active species, surface acidity, and basicity are optimized, resulting in a cyclohexene yield of 8.9%. The cyclohexene yield and stability of the 3D-printed catalysts are significantly higher than those of the granular catalyst, attributed to enhanced heat and mass transfer performance facilitated by the internal channels. Full article

Additive manufacturing methods can constitute a valuable alternative to conventional production techniques for components used in the heavy industry, particularly in foundry applications. This innovative manufacturing approach enables an expanded product portfolio as well as higher precision and geometrical complexity of ceramic components. One additive technology applicable to ceramic processing is robocasting, classified within the direct ink writing (DIW) family. In this method, a semi-fluid ceramic paste is extruded to build the part layer by layer; the shaped green body is subsequently fired (sintered) to attain its final functional properties. This study presents the results of materials characterization of printed ceramic filters, encompassing phase composition analysis, density measurements, three-point bending strength testing, hardness, and microstructural examination. The investigations demonstrated that the oxide ceramic Al₂O₃ processed by the modern robocasting method exhibits mechanical performance at a comparably high level relative to classical manufacturing routes (slip casting, ceramic injection molding, dry pressing). Moreover, the porosity results indicate that 3D printing technology enables lower post-sintering porosity. Full article

The increasing demand for novel tissue engineering (TE) applications in bone tissue regeneration underscores the importance of exploring advanced manufacturing techniques and biomaterials for personalised treatment approaches. Three-dimensional printing (3DP) technology facilitates the development of implantable devices with intricate geometries, enabling patient-specific therapeutic solutions. Although Fused Filament Fabrication (FFF) and Direct Ink Writing (DIW) are widely utilised for fabricating bone-like implants, the need for multiple processing steps often prolongs the overall production time. In this study, a single-step melt-extrusion 3DP technique was performed to develop multi-material scaffolds including bioceramics, hydroxyapatite (HA), and β-tricalcium phosphate (TCP) in both their bioactive and calcined forms at 10% and 20% w/w, within polycaprolactone (PCL) matrices. Printing parameters were optimised, and physicochemical properties of all biomaterials and final forms were evaluated. Thermal degradation and surface morphology analyses assessed the consistency and distribution of the ceramics across the different formulations. The tensile testing of the scaffolds defined the impact of each ceramic type and wt% on scaffold flexibility performance, while in vitro cell studies determined the cytocompatibility efficiency. Hence, all 3D-printed PCL–ceramic composite scaffolds achieved structural integrity and physicochemical and thermal stability. The mechanical profile of extruded samples was relevant to the ceramic consistency, providing valuable insights for further mechanotransduction investigations. Notably, all materials showed high cell viability and proliferation, indicating strong biocompatibility. Therefore, this additive manufacturing (AM) process is a precise and fast approach for developing biomaterial-based scaffolds, with potential applications in surgical restoration and support of segmental bone defects. Full article

The present study offers a systematic review of the current state of research on lattice structures manufactured by additive technologies for biomedical applications, with the aim of identifying common patterns, such as the use of triply periodic minimal surfaces (TPMS) for bone scaffolds, as well as technological gaps and future research opportunities. Employing the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) methodology, the review process ensures methodological rigor and replicability across the identification, screening, eligibility, and inclusion phases. Additionally, PRISMA was tailored by prioritizing technical databases and engineering-specific inclusion criteria, thereby aligning the methodology with the scope of this field. In recent years, a substantial surge in interdisciplinary research has underscored the promise of architected porous structures in enhancing mechanical compatibility, fostering osseointegration, and facilitating personalized medicine. A growing body of literature has emerged that explores the optimization of geometric features to replicate the behavior of biological tissues, particularly bone. Additive manufacturing (AM) has played a pivotal role in enabling the fabrication of complex geometries that are otherwise unachievable by conventional methods. The applications of lattice structures range from permanent load-bearing implants, commonly manufactured through selective laser melting (SLM), to temporary scaffolds for tissue regeneration, often produced with extrusion-based processes such as fused filament fabrication (FFF) or direct ink writing (DIW). Notwithstanding these advances, challenges persist in areas such as long-term in vivo validation, standardization of mechanical and biological testing, such as ISO standards for fatigue testing, and integration into clinical workflows. Full article

In the healthcare industry, the selection of biocompatible materials suitable for 3D printing is markedly less extensive than what is typically available through conventional manufacturing processes. Liquid silicone rubber (LSR) is distinguished by its exceptional stability, excellent biocompatibility, and considerable flexibility, offering significant prospects for manufacturers of medical devices involved in 3D printing. The primary aim of this research is to examine the essential factors and their interconnections that affect the 3D printing process with a Direct Ink Writing (DIW) 3D printer, which is specifically tailored for the production of aortic heart valves made from UV-cured silicone. Additionally, this study aims to investigate how the size of the heart valve impacts cardiac performance. This study implements House of Quality (HOQ) and Interpretive Structural Modeling (ISM) techniques to evaluate the interrelations among the different factors identified in the 3D printing process. Liquid silicone is especially advantageous for Direct Ink Writing (DIW) due to its low-temperature curing properties and low viscosity, which enable precise printing for intricate designs. Two different sizes of aortic heart valves, namely 23 mm and 36 mm, will be manufactured using UV-cured silicone, with both sizes having the same leaflet thickness of 0.8 mm and 1.6 mm. An examination will be conducted to assess how the size of the valve influences its performance and functionality. A Mock Circulatory Loop experimental setup will be used to test the silicone-printed heart valves, focusing on their capacity to maintain unidirectional flow and inhibit backflow through the flexible leaflets that function in alignment with the cardiac cycle. Full article

Direct ink writing (DIW) has emerged as a powerful technique for functional-structure fabrication. However, its application to materials with heterogeneous or time-dependent rheology remains limited. This study introduces dual-mode electropneumatic extrusion, supported by a real-time digital twin. This platform integrates a motorized pneumatic cylinder with an electropneumatic pressure regulator, enabling continuous blending of pressure and displacement control. System performance is evaluated across five material characteristics: homogeneity, heterogeneity, time-dependent rheology, self-curing ability, and thermoplasticity. The results demonstrate that feedback current control reduces the linewidth variability to ≈2% and settling time to <250 ms, even under four-fold increases in viscosity. Adaptive pressure ramps restore variability to ≤4% throughout material curing, while hybrid velocity–pressure operation maintains variability at ≤4% and a pore geometry error below 4% over 20 layers. These findings establish a robust framework for rheology-adaptive DIW and offer practical guidelines for implementing dual-mode control in high-throughput, multi-nozzle applications. Full article

Developing advanced nuclear fuel technologies is critical for high-performance applications such as nuclear thermal propulsion (NTP). This study explores the feasibility of direct ink writing (DIW) for fabricating ceramic pellets for potential nuclear applications. Zirconium carbide (ZrC) is used as a matrix material and vanadium carbide (VC) is used as a surrogate for uranium carbide (UC) in this study. A series of ink formulations were developed with varying concentrations of VC and nanocrystalline cellulose (NCC) to optimize the rheological properties for DIW processing. Post-sintering analysis revealed that conventionally sintered samples at 1750 °C exhibited high porosity (>60%), significantly reducing the compressive strength compared to dense ZrC ceramics. However, increasing VC content improved densification and mechanical properties, albeit at the cost of increased shrinkage and ink flow challenges. Spark plasma sintering (SPS) achieved near-theoretical density (~97%) but introduced geometric distortions and microcracking. Despite these challenges, this study demonstrates that DIW offers a viable route for fabricating ZrC-based ceramic structures, provided that sintering strategies and ink rheology are further optimized. These findings establish a baseline for DIW of ZrC-based materials and offer valuable insights into the porosity control, mechanical stability, and processing limitations of DIW for future nuclear fuel applications. Full article

Graphene is considered one of the most promising flexible transparent electrode materials as it has high charge carrier mobility, high electrical conductivity, low optical absorption, excellent mechanical strength, and good bendability. However, graphene-based flexible transparent electrodes face a critical challenge in balancing electrical conductivity and optical transmittance. Here, we present a green and scalable direct ink writing (DIW) strategy to fabricate graphene grid patterns by optimizing ink formulation with sodium dodecyl sulfate (SDS) and ethanol. SDS eliminates the coffee ring effect via Marangoni flow, while ethanol enhances graphene flake alignment during hot-pressing, achieving a high conductivity of 5.22 × 10⁵ S m⁻¹. The grid-patterned graphene-based flexible transparent electrodes exhibit a low sheet resistance of 21.3 Ω/sq with 68.5% transmittance as well as a high stability in high-temperature and corrosive environments, surpassing most metal/graphene composites. This method avoids toxic solvents and high-temperature treatments, demonstrating excellent stability in harsh environments. Full article

Solid-state electrolytes (SSEs) have emerged as a promising solution for next-generation lithium-ion batteries due to their excellent safety and high energy density. However, their practical application is still hindered by critical challenges such as their low ionic conductivity and high interfacial resistance at room temperature. The innovative application of 3D printing in the field of electrochemistry, particularly in solid-state electrolytes, endows energy storage devices with attractive characteristics. In this study, ceramic-in-gel polymer electrolytes (GPEs) based on PVDF-HFP/PAN@LLZTO were fabricated using a direct ink writing (DIW) 3D printing technique. Under the optimal printing conditions (printing speed of 40 mm/s and fill density of 70%), the printed electrolyte exhibited a uniform and dense sponge-like porous structure, achieving a high ionic conductivity of 5.77 × 10⁻⁴ S·cm⁻¹, which effectively facilitated lithium-ion transport. A structural analysis indicated that the LLZTO fillers were uniformly dispersed within the polymer matrix, significantly enhancing the electrochemical stability of the electrolyte. When applied in a LiFePO₄|GPEs|Li cell configuration, the electrolyte delivered excellent electrochemical performance, with high initial discharge capacities of 168 mAh·g⁻¹ at 0.1 C and 166 mAh·g⁻¹ at 0.2 C, and retained 92.8% of its capacity after 100 cycles at 0.2 C. This work demonstrates the great potential of 3D printing technology in fabricating high-performance GPEs. It provides a novel strategy for the structural design and industrial scalability of lithium-ion batteries. Full article

This study investigates the application of additive manufacturing (AM) in fabricating transverse thermoelectric (TTE) composites, demonstrating the feasibility of this methodology for TTE material synthesis. Zinc oxide (ZnO), a wide-bandgap semiconductor with moderate thermoelectric performance, and copper (Cu), a highly conductive metal, were selected as base materials. These were formulated into stable paste-like feedstocks for direct ink writing (DIW). A custom dual-nozzle 3D printer was developed to precisely deposit these materials in pre-designed architectures. The resulting structures exhibited measurable transverse Seebeck effects. Unlike prior TE research primarily focused on longitudinal configurations, this work demonstrates a novel AM-enabled strategy that integrates directional compositional anisotropy, embedded metal–semiconductor interfaces, and scalable multi-material printing to realize TTE behavior. The approach offers a cost-effective and programmable pathway toward next-generation energy harvesting and thermal management systems. Full article

Stimulus-responsive hydrogels have broad applications in the biomedical, sensing, and actuation fields. However, conventional fabrication methods are often limited to 2D structures, hindering the creation of complex, personalized 3D hydrogel architectures. Furthermore, hydrogels responding to only a single stimulus and delays in fabrication techniques restrict their practical utility in biomedicine. In this study, we developed two novel multi-stimuli-responsive hydrogels (based on Gelatin/Sodium Alginate and Tannic Acid/EDTA-FeNa complexes) specifically designed for direct ink writing (DIW) 3D printing. We systematically characterized the printed properties and optimized component ratio, revealing sufficient mechanical strength (e.g., tensile modulus: Gel/SA-TA ≥ 0.22854 ± 0.021 MPa and Gel/SA-TA@Fe³⁺ ≥ 0.35881 ± 0.021 MPa), high water content (e.g., water absorption rate Gel/SA-TA ≥ 70.21% ± 1.5% and Gel/SA-TA@Fe³⁺ ≥ 64.86% ± 1.28%), excellent biocompatibility (e.g., cell viability: Gel/SA-TA and Gel/SA-TA@Fe³⁺ ≥ 90%) and good shape memory performance (e.g., the highest shape recovery rate of Gel/SA-TA reaches 74.85% ± 4.776%). Furthermore, we explored electrical characteristics, showing that the impedance value of Gel/SA-TA@Fe³⁺ hydrogel changes significantly under finger bending and NIR irradiation. This investigation demonstrates the potential of these 3D-printed multi-stimuli hydrogels for applications such as wearable flexible strain sensors. Full article

The development of biocompatible, conductive hydrogels via direct ink writing (DIW) has gained increasing attention for strain sensor applications. In this work, a hydrogel matrix composed of polyvinyl alcohol (PVA) and κ-carrageenan (KC) was formulated and enhanced with polyvinylidene fluoride (PVDF) and silver nanoparticles (AgNPs) to impart piezoelectric properties. The ink formulation was optimized to achieve shear-thinning and thixotropic recovery behavior, ensuring printability through extrusion-based 3D printing. The resulting hydrogels exhibited high water uptake (~280–300%) and retained mechanical integrity. Rheological assessments showed that increasing PVDF content improved stiffness without compromising printability. Electrical characterization demonstrated that AgNPs were essential for generating piezoelectric signals under mechanical stress, as PVDF alone was insufficient. While AgNPs did not significantly alter the crystalline phase distribution of PVDF, they enhanced conductivity and signal responsiveness. XRD and SEM-EDX analyses confirmed the presence and uneven distribution of AgNPs within the hydrogel. The optimized ink formulation (5% PVA, 0.94% KC, 6% PVDF) enabled the successful fabrication of functional sensors, highlighting the material’s strong potential for use in wearable or biomedical strain-sensing applications. Full article

Direct ink writing (DIW) is an attractive, extrusion-based, additive manufacturing method for fabricating scaffold structures with controlled porosity using custom composite inks. Polycaprolactone–bioactive glass (PCL-BG) inks have gained attention for bone applications, but optimizing the formulation and fabrication of PCL-BG-based inks for improved printability and desired mechano-biological properties remains a challenge. This study employs a two-step design to systematically evaluate the effect of three factors in terms of PCL-BG composite printability and mechano-biological properties: ink preparation (acetone or dichloromethane (DCM) as the solvent, and mechanical compounding), the extrusion temperature (90 °C, 110 °C, and 130 °C), and the BG content (0%, 10%, and 20% BG). Pure PCL was used as the control. Rheological, calorimetric, and thermo-gravimetric analyses were conducted before printing. Cylindrical scaffolds and solid wells were printed to evaluate the printability, mechanical properties, and cytocompatibility. The scaffold porosity and pore size were carefully examined. Mechanical tests demonstrated that composite formulations with added BG and higher printing temperatures increased the elastic modulus and yield strength. However, PCL-DCM-BG combinations exhibited increased brittleness with higher BG content. Despite concerns about the toxic solvent DCM, the cytocompatibility was comparable to pure PCL for all ink preparation methods. The results suggest that the interaction between the ink preparation solvent, the BG content, and the printing temperature is critical for material design and fabrication planning in bone tissue engineering applications, providing insights into optimizing PCL-BG composite ink formulations for 3D printing in bone tissue engineering. Full article

High-performance flexible sensors capable of direct integration with biological tissues are essential for personalized health monitoring, assistive rehabilitation, and human–machine interaction. However, conventional devices face significant challenges in achieving conformal integration with biological surfaces, along with sufficient biomechanical compatibility and biocompatibility. This research presents an in situ 3D biomanufacturing strategy utilizing Direct Ink Writing (DIW) technology to fabricate functional bioelectronic interfaces directly onto human skin, based on a novel annealing PEDOT:PSS/PVA composite bio-ink. Central to this strategy is the utilization of a novel annealing PEDOT:PSS/PVA composite material, subjected to specialized processing involving freeze-drying and subsequent thermal annealing, which is then formulated into a DIW ink exhibiting excellent printability. Owing to the enhanced network structure resulting from this unique fabrication process, films derived from this composite material exhibit favorable electrical conductivity (ca. 6 S/m in the dry state and 2 S/m when swollen) and excellent mechanical stretchability (maximum strain reaching 170%). The material also demonstrates good adhesion to biological interfaces and high-fidelity printability. Devices fabricated using this material achieved good conformal integration onto a finger joint and demonstrated strain-sensitive, repeatable responses during joint flexion and extension, capable of effectively transducing local strain into real-time electrical resistance signals. This study validates the feasibility of using the DIW biomanufacturing technique with this novel material for the direct on-body fabrication of functional sensors. It offers new material and manufacturing paradigms for developing highly customized and seamlessly integrated bioelectronic devices. Full article