Search Results (264)

In this paper, the molecular dynamics simulation method was adopted to systematically study the microstructure evolution behavior of TiAl alloys under impact compression under three typical crystal orientations ([001], [110], [111]). By analyzing the characteristics of structural phase transition, defect type evolution, dislocation expansion, and radial distribution function, the anisotropic response mechanism under the joint regulation of crystal orientation and impact velocity was revealed. The results show that the [111] crystal orientation is most prone to local amorphous transformation at high strain rates, and its structural collapse is due to the rapid accumulation and limited reconstruction of dislocations/faults. The [001] crystal orientation is prone to forming staggered stacking of layers and local HCP phase transformation, presenting as a medium-strength structural disorder. Under the strain regulation mechanism dominated by twinning, the [110] orientation exhibits superior structural stability and anti-disorder ability. With increases in the impact velocity, the defect type gradually changes from isolated dislocations to large-scale HCP regions and amorphous bands, and there are significant differences in the critical velocities of amorphous transformation corresponding to different crystal orientations. Further analysis indicates that the HCP structure and the formation of layering faults are important precursor states of amorphous transformation. The evolution of the g(r) function verifies the stepwise disintegration process of medium and long-range ordered structures under shock induction. It provides a new theoretical basis and microscopic perspective for the microstructure regulation, damage tolerance improvement, and impact resistance design of TiAl alloys under extreme stress conditions. Full article

Alzheimer’s disease is the most widespread neurodegenerative disease in the world. Galantamine hydrobromide (GH) is one of the drugs used to treat mild to moderate dementia of the Alzheimer type. Due to the fact that the specificity of the disease requires maximally facilitated intake, orodispersible films present such an opportunity. In the present study orodispersible films based on poly(2-ethyl-2-oxazoline) as well as partially hydrolyzed poly(2-ethyl-2-oxazoline) were prepared and studied as delivery systems for GH. Two samples of partially hydrolyzed PEtOx were synthesized—one of relatively low degree of hydrolysis and another one of relatively high degree of hydrolysis, and studied by Nuclear Magnetic Resonance (NMR). Cytotoxicity assay was performed that validated the low hydrolyzed derivative as biocompatible polymer that maintained desirable physicochemical characteristics without compromising the safety, thereby it was selected for further research. The films were prepared by the solution casting method and characterized by different methods. FTIR was used to determine the potential interactions between the galantamine molecule and the film components. Based on the Thermogravimetric Analysis (TGA) conducted, it was concluded that all films were sufficiently thermally stable, as the component decomposition stage (after initial solvent removal) began above 180 °C. The polymer films were further characterized with the determination of Shore hardness and the results showed that the films containing glycerol as a plasticizer exhibited higher hardness compared to those with PEG as a plasticizer. The disintegration time of the films was determined visually using Petri dishes and it was found that the films disintegrated within the range of 0.52 to 1.58 min, fully meeting the pharmacopoeial requirements. GH release profiles in PBS at 37 °C were obtained, and it was found that by the second minute, 80–90% of the drug were released from the different films, and the release followed an anomalous diffusion mechanism (Case II). Full article

Slender masonry structures, in the absence of disintegration phenomena, can be idealized as rigid bodies subjected to seismic excitation. In this study, a closed-form expression for the behavior factor (q-factor) associated with overturning collapse under out-of-plane seismic loading is derived. The analysis considers five-step pulse seismic inputs. In the proposed approach, valid for slender masonry structures, sliding failure is neglected, and collapse is assumed to occur when, at the end of the seismic excitation, the rotation of the structure reaches a value equal to its slenderness. Based on this criterion, it is possible to derive a formulation for the q-factor as a function of a dimensionless parameter that combines the geometric characteristics of the slender structure and the period of the applied accelerogram. To validate the proposed formulation, a comparative analysis is conducted against the results obtained from a numerical integration of the motion equation using a set of 20 natural accelerograms recorded in Italy. The characteristic period of each accelerogram is evaluated through different methodologies, with the aim of identifying the most suitable approach for application in simplified seismic assessment procedures. Full article

Background/Objectives: Hot-melt extrusion (HME) has gained prominence for the manufacture of sustained-release oral dosage forms, yet the application of wax-based matrices and their resilience to alcohol-induced dose dumping (AIDD) remains underexplored. This study aimed to develop and characterise wax-based sustained-release felodipine formulations, with a particular focus on excipient functionality and robustness against AIDD. Methods: Felodipine sustained-release formulations were prepared via HME using Syncrowax HGLC as a thermally processable wax matrix. Microcrystalline cellulose (MCC) and lactose monohydrate were incorporated as functional fillers and processing aids. The influence of wax content and filler type on mechanical properties, wettability, and drug release behaviour was systematically evaluated. Ethanol susceptibility testing was conducted under simulated co-ingestion conditions (4%, 20%, and 40% v/v ethanol) to assess AIDD risk. Results: MCC-containing tablets demonstrated superior sustained-release characteristics over 24 h, showing better wettability and disintegration. In contrast, tablets formulated with lactose monohydrate remained structurally intact during dissolution, overly restricting drug release. This limitation was effectively addressed through granulation, where reduced particle size significantly improved surface accessibility, with 0.5–1 mm granules achieving a satisfactory release profile. Ethanol susceptibility testing revealed divergent behaviours between the two filler systems. Unexpectedly, MCC-containing tablets showed suppressed drug release in ethanolic media, likely resulting from inhibitory effect of ethanol on filler swelling and disintegration. Conversely, formulations containing lactose monohydrate retained their release performance in up to 20% v/v ethanol, with only high concentrations (40% v/v) compromising matrix drug-retaining functionality and leading to remarkably increased drug release. Conclusions: This study highlights the pivotal role of excipient type and constitutional ratios in engineering wax-based sustained-release formulations. It further contributes to the understanding of AIDD risk through in vitro assessment and offers a rational design strategy for robust, alcohol-resistant oral delivery systems for felodipine. Full article

Three-dimensional (3D) computational fluid dynamic (CFD) simulations have been performed to investigate the complex flow features and stripping of fluid materials from a cylindrical water drop at the late-stage in a Shock Liquid Drop Interaction (SLDI) process when the drop’s downstream end experiences compression after it is impacted by a supersonic shock wave ($Ma$ = 1.47). The drop trajectory/breakup has been simulated using a Lagrangian model and the unsteady Reynolds-averaged Navier–Stokes (URANS) approach has been employed for simulating the ambient airflow. The Kelvin–Helmholtz Rayleigh–Taylor (KHRT) breakup model has been used to capture the liquid drop fragmentation process and a coupled level-set volume of fluid (CLSVOF) method has been applied to investigate the topological transformations at the air/water interface. The predicted changes of the drop length/width/area with time have been compared against experimental measurements, and a very good agreement has been obtained. The complex flow features and the qualitative characteristics of the material stripping process in the compression phase, as well as disintegration and flattening of the drop are analyzed via comprehensive flow visualization. Characteristics of the drop distortion and fragmentation in the stripping breakup mode, and the development of turbulence at the later stage of the shock drop interaction process are also examined. Finally, this study investigated the effect of increasing $Ma$ on the breakup of a water drop by shear stripping. The results show that the shed fluid materials and micro-drops are spread over a narrower distribution as $Ma$ increases. It illustrates that the flattened area bounded by the downstream separation points experienced less compression, and the liquid sheet suffered a slower growth. Full article

Loess Plateau is the region with the most concentrated loess distribution and the deepest loess soil layer in the world, and it is facing serious problems of soil erosion and ecological degradation. The nano carbon modification of soil surface properties is a novel strategy for soil improvement and enhancing the soil’s capacity to sequester carbon, which has been extensively researched. However, the mechanisms underlying the influence of carbon surface structure on the efficacy of loess soil remediation remain unclear. Herein, graphene oxide (GO) with a unique two-dimensional structure and adjustable surface properties was optimized as a model carbon filler to investigate the modification effect on loess. As a result, the addition amount of 0.03% GO significantly reduced the disintegration amount of loess, but, if inhibited for a long time, the disintegration effect would weaken. The highly reduced GO can delay the loess disintegration rate due to its enhanced hydrophobicity, but the inhibitory effect fails over a long period of time. After adjusting the reduce degree with a 50% SA (sodium ascorbate), the water-holding capacity of the modified soil in the high suction range is enhanced. This study reveals the synergistic mechanism of the sheet structure and surface properties of GO on the water stability of loess, providing a reference for the prevention and control of soil erosion and ecological restoration in the Loess Plateau. Full article

During the construction of subgrade, the remolding water content w of lime–sand-stabilized clay usually varies in a wide range, leading to inconsistent effectiveness in strength enhancement. Until now, this aspect has not been investigated. In this study, an unconfined compression test and microscopic observation were carried out on clay and stabilized clay (adding 4% lime by mass and 50% sand by volume). The results show the following: (1) remolding water content w had a strong effect on the soil fabrics of pure clay and lime-stabilized clay. An increase in the w from the dry to wet side of optimum reduced matric suction, which diminished the aggregation effect among fine-grained particles in both clay and lime-stabilized clay. Correspondingly, fine-grained aggregate progressively disintegrated, and dispersed fine-grained particles increased. As a result, the w increment at w ≤ w_cha made the dispersed fine-grained particles successively fill the large pores between aggregates, densifying the soil fabric. In contrast, at w > w_cha, the ongoing disintegration of aggregate resulted in progressive structural weakening. Herein, w_cha was defined as the characteristic water content at which the soil fabric transitioned from structural densification to weakening. (2) The UCS of both pure clay and lime–sand-stabilized clay followed a bell-shaped pattern as the w increased, with w_cha acting as the turning point. For pure clay soils, the UCS increased with increasing w up to w_cha because of structural densification, but decreased beyond w_cha due to structural weakening. In lime–sand-stabilized clay, where a sand grain skeleton developed, the compression of lime-stabilized clay induced by the movement of sand grains during shearing activated its contribution to the overall strength. The compressive capacity of the lime-stabilized clay varied in a bell-shaped manner with w, and this trend was mirrored in the UCS of lime–sand-stabilized clay. (3) At a low w, the fact that the clay aggregate exhibited sand-like mechanical behavior reduced the effectiveness of incorporating sand and lime for enhancing the UCS. As the w increased at w ≤ w_cha, the breakdown of aggregates enlarged the distinction between pure clay and sand, resulting in a more pronounced improvement in the UCS with the addition of sand and lime. At w > w_cha, the lubrication effect occurring at the contact between sand grains diminished the interlocking between the sand grains. Consequently, the effectiveness of the UCS enhancement decreased. Full article

The fast-disintegrating capsules rapidly disintegrate in various physiological environments, ensuring therapeutic efficacy. The formulation of plant-based capsules with balanced mechanical and fast disintegration characteristics continues to present technical challenges in pharmaceutical development. In this study, natural marine polysaccharides were utilized to achieve both rapid disintegration and excellent mechanical properties by combining κ-Carrageenan (κ-C) and ι-Carrageenan (ι-C). Additionally, the selection of KCl + NaCl mixed coagulants, along with the evaluation of their types, mass fractions, and ratios, enhanced the mechanical properties and transmittance of the capsules. FTIR analysis revealed that the membrane with a 5:5 κ-C/ι-C ratio formed hydrogen bonds, which were beneficial to its fast disintegration. SEM analysis revealed a dense microstructure in this formulation, contributing to its improved mechanical properties. Finally, this study hypothesizes that the disintegration behaviors of the capsules exhibited significant pH dependence, with ion exudation predominating in pH 1.2 and pH 7.0 media, while swelling dominated under pH 4.5 and pH 6.8 media. The prepared carrageenan blend-based capsules exhibited fast disintegration properties while maintaining excellent mechanical and barrier properties, thereby broadening the application of plant-based capsules in the field of medicine. Full article

Aim: This study aimed to evaluate the potential impact of stone characteristics, patient factors, and upper tract anatomical parameters in the prediction of residual fragments (RFs) following the flexible ureteroscopic (fURS) management of renal stones. Patients and Methods: Between June 2023 and July 2024, a total of 104 cases underwent fURS for the minimally invasive management of medium-sized renal stones (10–25 mm), and 28 cases presenting with RFs 3 months after these procedures were included for further evaluation. In addition to the assessment of patient-related factors, non-contrast computed tomography (NCCT) was performed in all cases in an attempt to assess specific stone characteristics and upper tract anatomical parameters in detail during the 3-month follow-up period. Results: An evaluation of our findings indicated that, among the evaluated parameters, a higher degree of hydronephrosis (>Grade 2), a larger stone size (>15 mm), and the presence of multiple stones were found to affect the presence of RFs significantly (p = 0.020, p = 0.012, and p = 0.040, respectively). On the other hand, although the analysis of other parameters such as patient gender, stone side, stone hardness, and the use of an access sheath with univariate regression demonstrated potential correlations, none of these parameters demonstrated a significant impact when analyzed using backward logistic regression. Logistic regression revealed that Grade 2 hydronephrosis (OR = 18.3, p = 0.020), stone size > 15 mm (OR = 7.0, p = 0.012), and multiple stones (OR = 3.7, p = 0.040) significantly increased the risk of residual fragments following fURS. Conclusions: In light of our findings and published data, we can conclude that endourologists should consider the likelihood of RFs’ presence after successful stone disintegration with fURS. A detailed evaluation of the relevant factors revealed that patients with larger stones, higher degrees of hydronephrosis, and multiple calculi may carry the risk of residual fragments after these procedures. Thus, the utilization of such reliable predictive parameters may aid in selecting optimal stone removal strategies and planning subsequent interventions in the rational management of RFs. Full article

USP (usual temperature pitch)-modified asphalt optimizes its rheological properties through reactions between the modifier and the asphalt. This significantly enhances the high- and low-temperature adaptability and environmental friendliness of asphalt. It has now become an important research direction in the field of highway engineering. This article systematically investigates the impact of different dosages of USP warm mix modifier on asphalt binders through rheological and microstructural analysis. Base asphalt and SBS-modified asphalt were blended with USP at varying ratios. Conventional tests (penetration, softening point, ductility) were combined with dynamic shear rheometry (DSR, AASHTO T315) and bending beam rheometry (BBR, AASHTO T313) to characterize temperature/frequency-dependent viscoelasticity. High-temperature performance was quantified via multiple stress creep recovery (MSCR, ASTM D7405), while fluorescence microscopy and FTIR spectroscopy elucidated modification mechanisms. Key findings reveal that (1) optimal USP thresholds exist at 4.0% for base asphalt and 4.5% for SBS modified asphalt, beyond which the rutting resistance factor (G*/sin δ) decreases by 20–31% due to plasticization effects; (2) USP significantly improves low-temperature flexibility, reducing creep stiffness at −12 °C by 38% (USP-modified) and 35% (USP/SBS composite) versus controls; (3) infrared spectroscopy displays that no new characteristic peaks appeared in the functional group region of 4000–1300 cm⁻¹ for the two types of modified asphalt after the incorporation of USP, indicating that no chemical changes occurred in the asphalt; and (4) fluorescence imaging confirmed that the incorporation of USP led to disintegration of the spatial network structure of the control asphalt, explaining the reason for the deterioration of high-temperature performance. Full article

This study investigated the solid-state reduction characteristics of natural chromite ore and the effect of iron powder on the solid-state reduction characteristics of natural chromite ore under isothermal conditions below 1200 °C. The enhancement mechanism of iron powder on the solid-state reduction of natural chromite ore was revealed using optical microscopy, X-ray diffraction (XRD), and scanning electron microscopy–energy dispersive spectroscopy (SEM-EDS). The iron metallization rate of chromite ore exhibited a trend of increasing first and then decreasing with the addition of iron powder, and the optimal iron powder addition was determined to be 30%. The multi-step reaction gradually transforms into a single-step reaction with the increase in the dosage of iron powder. Iron powder facilitates the generation of a low-melting Fe-C alloy liquid phase and accelerates the speed of the solid-state reduction reaction of chromite ore and the disintegration of chromite spinel particles. When the iron powder dosage exceeds 30%, most of the multi-step reduction reaction of chromite ore is transformed into the single-step reduction reaction, which reduces the disintegration of chromite spinel particles and weakens the enhancement effect of iron powder on the solid-state reduction of chromite ore. Full article

Public health crises triggered by viral infections pose severe threats to individual health and disrupt global socioeconomic systems. Against the backdrop of global pandemics caused by highly infectious diseases such as COVID-19 and Ebola virus disease (EVD), the development of innovative prevention and treatment strategies has become a strategic priority in the field of biomedicine. Neutralizing antibodies, as biological agents, are increasingly recognized for their potential in infectious disease control. Among these, nanobodies (Nbs) derived from camelid heavy-chain antibodies exhibit remarkable technical advantages due to their unique structural features. Compared to traditional neutralizing antibodies, nanobodies offer significant cost-effectiveness in production and enable versatile administration routes (e.g., subcutaneous injection, oral delivery, or aerosol inhalation), making them particularly suitable for respiratory infection control and resource-limited settings. Furthermore, engineered modification strategies—including multivalent constructs, multi-epitope recognition designs, and fragment crystallizable (Fc) domain fusion—effectively enhance their neutralizing activity and suppress viral immune escape mechanisms. Breakthroughs have been achieved in combating pathogens such as the Ebola virus and SARS-CoV-2, with mechanisms involving the blockade of virus–host interactions, induction of viral particle disintegration, and enhancement of immune responses. This review comprehensively discusses the structural characteristics, high-throughput screening technologies, and engineering strategies of nanobodies, providing theoretical foundations for the development of novel antiviral therapeutics. These advances hold strategic significance for addressing emerging and re-emerging infectious diseases. Full article

Early caregiving can evoke feelings of helplessness in mothers that are potentially associated with disintegrative responses, i.e., intrusive thoughts and dissociative experiences in the context of infant care. Given the associated increase in stress and exposure to life-threatening dangers, crises such as pandemics and wars may intensify these responses, but this has not previously been tested. Objectives: This cross-sectional study aimed to (1) examine maternal disintegrative responses across three contexts—a high-intensity phase of the COVID-19 pandemic, a subsequent low-intensity pandemic period, and the Israel–Hamas war—and (2) compare the two crisis periods in terms of trauma-related exposure, a damaged experience of childbirth and childcare, and their links to disintegrative responses. Method: This study had two parts and was conducted among Israeli mothers. Part 1 involved 1416 mothers across three groups: high-intensity pandemic (N = 637), low-intensity pandemic (N = 360), and war (N = 419). Part 2 involved a subsample from Part 1 comparing the 1056 mothers from the high-intensity pandemic and war groups. All the participants completed questionnaires assessing maternal disintegrative responses, trauma-related exposure, and a damaged experience of childbirth and childcare. The analyses included ANOVA and mediation models, controlling for maternal characteristics. Results: Intrusive thoughts and dissociative experiences were significantly higher during both the high-intensity pandemic and war periods compared to the low-intensity pandemic period. Trauma exposure indirectly predicted intrusive thoughts and dissociative experiences through a damaged experience of childbirth and childcare, particularly during war. Conclusions: The findings indicate that maternal disintegrative responses were higher during high-intensity crisis contexts, with the highest levels reported by mothers during the war. Trauma exposure and a damaged experience of childbirth and childcare were associated with more intrusive thoughts and dissociative experiences, underscoring the need for targeted support to protect maternal well-being and caregiving during crises. Full article

Spraying remains the primary method of pesticide application in plant protection, and spray drift is one of the important reasons that cause pesticide loss and environmental pollution. Air-induction spray is an anti-drift technology based on the Venturi effect. Unlike standard flat-fan sprays, the atomization mechanism of air-induction sprays has not yet been thoroughly studied. Therefore, a deep understanding of atomization and disintegration characteristics of air-induction spray liquid sheets is very important. This study utilized high-speed camera imaging technology to visualize the liquid sheet of air-induction sprays. Quantitative measurements were conducted on the disintegration length, spray angle, and bubble size of the liquid sheets. A comparative analysis was performed to examine the differences in liquid sheet structures between air-induction sprays and standard flat-fan sprays. The effects of different nozzle configurations and spray pressures on the liquid sheet of air-induction sprays were also discussed. The results indicate that bubbles are typical structures of the liquid sheets of the air-induction spray, and their disintegration can lead to perforations or interfacial disturbances in the liquid sheet. The study observed the coalescence of double or multiple bubbles within the liquid sheet, with atomized droplets potentially containing single or multiple bubbles. Compared to standard flat-fan sprays, air-induction sprays have smaller liquid sheet spray angles and disintegration lengths, by 23.48% and 16.32%, respectively. Bubble size decreases with increasing spray pressure but increases with larger nozzle orifice sizes. The spray angle of the liquid sheet significantly increases with higher spray pressures and larger nozzle orifice sizes. Meanwhile, the disintegration length of the liquid sheet shows a slight increase with rising spray pressures and larger nozzle orifice sizes. Full article

Methods: Effervescent granules containing citric acid and sodium bicarbonate were successfully prepared for the first time via TS-MG using a polyol (sorbitol) as a melt binder. Results: Processing parameters, specifically granulation temperature and screw speed, were systematically varied to investigate their influence. The granulation efficiency, inversely related to the wt.% of fines, decreased in the following order across the tested conditions (granulation temperature–screw speed; ℃-rpm): 95-6 > 100-5 > 90-5 > 100-7 > 90-7. Granulation temperature had a minimal impact on the bulk and tapped densities of the uncalibrated granules, whereas increased screw speed led to higher densities, associated with a reduced proportion of fines. The tensile strength of the resulting effervescent tablets increased with granulation temperature and was generally higher for tablets derived from granules with higher granulation efficiency. The residence time within the TS-MG barrel decreased with increasing temperature and screw speed. Notably, the greatest effect of granulation temperature on tensile strength occurred between 90 and 95 °C, particularly under longer residence times. The disintegration time of the tablets was shortest for the 90 °C and 5 rpm condition, corresponding to the lowest tensile strength, while tablets across formulations showed consistent homogeneity as indicated by similar pH values post-disintegration. Conclusions: These findings underscore sorbitol’s suitability as a melt binder and highlight the interplay between TS-MG parameters and the physical characteristics of effervescent granules and tablets. Full article