Search Results (5)

The article presents a mathematical description of the thermal phenomena occurring both inside and on the surfaces of a homogeneous plate subjected to an external heat flux on one side. Analytical formulae for thermal excitation, with a given duration and constant power, are derived, enabling the determination of temperature increases on both the heated and unheated surfaces of the plate under specific heat transfer conditions to the surroundings. Convective heat transfer, with individual heat transfer coefficients on both sides of the slab, is considered; however, radiative heat loss can also be included. The solution of the problem obtained using two methods is presented: the method of separation of variables (MSV) and the Laplace transform (LT). The advantages and disadvantages of both analytical formulae, as well as the impact of various factors on the accuracy of the solution, are discussed. Among others, the MSV solution works well for a sufficiently long time, whereas the LT solution is better for a sufficiently short time. The theoretical considerations are illustrated with diagrams for several configurations, each representing various heat transfer conditions on both sides of the plate. The presented solution can serve as a starting point for further analysis of more complex geometries or multilayered structures, e.g., in non-destructive testing using active thermography. The developed theoretical model is verified for a determination of the thermal diffusivity of a reference material. The model can be useful for analyzing the method’s sensitivity to various factors occurring during the measurement process, or the method can be adapted to a pulse of known duration and constant power, which is much easier to implement technically than a very short impulse (Dirac) with high energy. Full article

Functional activation leads to an increase in local brain temperature via an increase in local perfusion. In the intraoperative setting, these cortical surface temperature fluctuations may be imaged using infrared thermography such that the activated brain areas are inferred. While it is known that temperature increases as a result of activation, a quantitative spatiotemporal description has yet to be achieved. A novel intraoperative infrared thermography device with data collection software was developed to isolate the thermal impulse response function. Device performance was validated using data from six patients undergoing awake craniotomy who participated in motor and sensory mapping tasks during infrared imaging following standard mapping with direct electrical stimulation. Shared spatiotemporal patterns of cortical temperature changes across patients were identified using group principal component analysis. Analysis of component time series revealed a thermal activation peak present across all patients with an onset delay of five seconds and a peak duration of ten seconds. Spatial loadings were converted to a functional map which showed strong correspondence to positive stimulation results for similar tasks. This component demonstrates the presence of a previously unknown impulse response function for functional mapping with infrared thermography. Full article

Thermal imaging plays a vital role in structural health monitoring of various materials and provides insight into the defect present due to aging, deterioration, and fault during construction. This study investigated the effectiveness of spatial filters during pre-processing of thermal images and a correlation technique in post-processing, as well as exploited its application in non-destructive testing and evaluation of defects in steel structures. Two linear filters (i.e., Gaussian and Window Averaging) and a non-linear filter (i.e., Median) were implemented during pre-processing of a pulsed thermography image sequence. The effectiveness of implemented filters was then assessed using signal to noise ratio as a quality metric. The result of pre-processing revealed that each implemented filter is capable of reducing impulse noise and producing high-quality images; additionally, when comparing the signal to noise ratio, the Gaussian filter dominated both Window Averaging and Median filters. Defect size was determined using a correlation technique on a sequence of pulsed thermography images that had been pre-processed with a Gaussian filter. Finally, it is concluded that the correlation technique could be applied to the fast measurement of defect size, even though the accuracy may depend on the detection limit of thermography and defect size to depth ratio. Full article

Gas turbines and their blades in particular might be damaged in the course of the aviation turbojet engine operation process. The degradation process of the blade microstructure is most evident from the change in the colour of its surface. This is assessed using the optoelectronic method. The article presents the concept of non-destructive methods, which are used to assess the degree of degradation of the alloy of a gas turbine blade. The proposed optoelectronic method is the basic method for the preliminary determination of color changes in the surface. Appropriate videoscopes or video-analyzers, capable of recording a test object in various electromagnetic wave ranges (infrared radiation, visible range), are used for this purpose. These preliminary results of the diagnosis make it possible to infer further studies of the blade. For accurate investigation of the state of the alloy microstructure, a non-destructive thermographic method (xenon flash pulsed thermography) was used. The results of studies of the degradation of the microstructure with the use of non-destructive methods were verified through the use of metallographic investigations. Appropriate metallographic specimens were created in order to recognize phase γ′ degradation (i.e., the phase strengthening the blade alloy). The results of the presented research allowed for an in-depth assessment of the degree of microstructure degradation of operated blades. Full article

Active thermal imaging is an effective nondestructive technique in the structural health monitoring field, especially for concrete structures not exposed directly to the sun. However, the impact of meteorological factors on the testing results is considerable and should be studied in detail. In this study, the impulse thermography technique with halogen lamps heat sources is used to detect defects in concrete structural components that are not exposed directly to sunlight and not significantly affected by the wind, such as interior bridge box-girders and buildings. To consider the effect of environment, ambient temperature and relative humidity, these factors are investigated in twelve cases of testing on a concrete slab in the laboratory, to minimize the influence of wind. The results showed that the absolute contrast between the defective and sound areas becomes more apparent with an increase of ambient temperature, and it increases at a faster rate with large and shallow delaminations than small and deep delaminations. In addition, the absolute contrast of delamination near the surface might be greater under a highly humid atmosphere. This study indicated that the results obtained from the active thermography technique will be more apparent if the inspection is conducted on a day with high ambient temperature and humidity. Full article