Search Results (6)

Superhydrophobic coatings are regarded as a promising passive anti-icing strategy; however, their practical engineering application, particularly in electrical insulation, is severely hindered by the performance deterioration caused by mechanical damage and a lack of theoretical understanding of microscopic ice adhesion mechanisms. In this study, a layered polymer composite coating was designed to resolve the trade-off between abrasion resistance and low ice adhesion. The chemistry of the coating relies on a synergistic “primer–topcoat” design: the primer consists of an epoxy resin matrix chemically modified by amino silicone oil to lower its surface energy and improve toughness, while the topcoat features hierarchical SiO₂ clusters functionalized with hexamethyldisilazane (HMDS) and silane coupling agents. This architecture was fabricated via a controllable layer-by-layer spraying method. Systematic investigations revealed that the hierarchical micro/nanostructure, composed of microscale protrusions and nanoscale SiO₂ clusters, provides excellent superhydrophobicity (contact angle of 155.2°, sliding angle of 2°). Crucially, the crosslinked polymer network and stable siloxane (Si-O-Si) covalent bonding ensure that the coating maintains its functionality after a cumulative sand impact of 3 kg, demonstrating superior mechanical durability. Furthermore, differentiated theoretical models for ice adhesion in Cassie–Baxter and Wenzel states were established based on intermolecular interactions, identifying that maintaining a stable Cassie–Baxter state is key to reducing adhesion. This study offers a robust approach to balancing functionality and durability in polymer composites through synergistic structural design, providing both a scalable fabrication strategy and a quantitative theoretical framework for understanding interfacial ice adhesion. Full article

The deposition of low-adhesive siloxane coatings is a current trend for the non-toxic control of bacterial growth and biofilm formation. Total elimination of biofilm formation has not been reported so far. The aim of this investigation was to study the ability of a non-toxic, natural, biologically active substance, such as fucoidan, to inhibit bacterial growth on similar medical coatings. The fucoidan amount was varied, and its impact on the bioadhesion-influencing surface characteristics, as well as on bacterial cell growth, was investigated. The inclusion of up to 3–4 wt.% brown algae-derived fucoidan in the coatings increases their inhibitory effect, more significantly on the Gram-positive bacterium S. aureus than on the Gram-negative bacterium Escherichia coli. The biological activity of the studied siloxane coatings was ascribed to the formation of a low-adhesive, biologically active surface top layer consisting of siloxane oil and dispersed water-soluble fucoidan particles. This is the first report on the antibacterial activity of fucoidan-containing medical siloxane coatings. The experimental results give reason to expect that relevantly selected, natural biologically active substances can be efficient in the non-toxic control of bacterial growth on medical devices and, as a result, medical device-associated infections. Full article

Atomic oxygen in the low Earth orbit (LEO) environment is highly oxidizing. Due to the high flight speed of spacecraft, the relative kinetic energy of high-flux atomic oxygen bombarding the spacecraft surface can reach up to about 5 eV. Therefore, atomic oxygen is one of the most dangerous space environment factors in LEO, which seriously affects the safe operation and service life of spacecraft in orbit. In order to meet the requirements for the high reliability and long lifetime of spacecraft, effective protection measures must be taken on their sensitive surfaces. Siloxane is a coating with an organic–inorganic hybrid structure. Compared with SiO₂ and other inorganic atomic oxygen protective coatings, it has better flexibility and is better at anti-atomic oxygen performance. In this paper, the plasma polymerization deposition technique was used to prepare large-area siloxane coatings on different substrates with different thicknesses for improving atomic oxygen resistance by optimizing the process parameters. The thickness of the coating was measured by different methods, and the results showed that the thickness distribution was consistent. By observing the surface morphology of the coating, it was uniform and compact without obvious defects, so the uniformity of large-area coating was also ideal. The adhesion and heat/humidity resistance of siloxane coatings were examined by pull-off testing and damp-heat testing, respectively. The results showed that the siloxane coatings with a thickness of about 400 nm exhibited better physical properties. At the same time, the ground simulation testing of atomic oxygen confirmed that siloxane coatings with a thickness of 418 nm presented the best performance of atomic oxygen resistance. The atomic oxygen erosion yield of siloxane coatings with a thickness of 418 nm was as low as 5.39 × 10⁻²⁷ cm³/atoms, which was three orders of magnitude lower than that of the uncoated Kapton substrate and presented a good anti-atomic oxygen performance. Meanwhile, it has also successfully passed the damp-heat test. The coating thickness is only several hundred nanometers and does not increase the weight of the spacecraft, which makes it a relatively ideal LEO atomic oxygen protection material. Furthermore, a possible mechanism was proposed to explicate the physicochemical process of atomic oxygen attacking the coating materials. Full article

No systematic study of antioxidant containing coatings and their anti-biofilm action has been reported so far. The utilization of antioxidants in protective coatings to inhibit marine biofilm formation is a current challenge. The aim of this preliminary study was to prepare, characterize and compare the efficiency of low adhesive siloxane composite coatings equally loaded with different antioxidants against mono-species biofilms formation. Most often participating in the marine biofilms formation, Marinobacter hydrocarbonoclasticus was the test bacterium. Both the biofilm covered surface area (BCSA) and corrected total cell fluorescence (CTCF) (by fluorescent microscopy) were selected as the parameters for quantification of the biofilm after 1 h and 4 h incubation. Differing extents of altered surface characteristics (physical-chemical; physical-mechanical) and the specific affection of M. hydrocarbonoclasticus biofilm formation in both reduction and stimulation, were found in the studied antioxidant containing coatings, depending on the chemical nature of the used antioxidant. It was concluded that not all antioxidants reduce mono-species biofilm formation; antioxidant chemical reactivity stipulates the formation of an altered vulcanization network of the siloxane composites and thus microbial adhesion which influences the surface characteristics of the vulcanized coatings; and low surface energy combined with a low indentation elastic modulus are probably pre-requisites of low microbial adhesion. Full article

We prepared a series of polyurethane (PU) coatings with defined contents using poly(tetramethylene oxide)glycol (PTMG) with two different molecular weights (i.e., M_n = 2000 and 650), as well as polydimethyl siloxane (PDMS) with a molecular weight of M_n 550. For every coating, maximum adhesive strength and excellent self-healing character (three times) were found using 6.775 mol% mixed with low-molecular-weight-based polyols (PU-11-3-3). Defined 1.0 wt% CeO₂ was also used for the PU-11-3-3 coating (i.e., PU-11-3-3-CeO₂) to obtain UV shielding properties. Both the in situ polymerization and blending processes were separately applied during the preparation of the PU-11-3-3-CeO₂ coating dispersion. The in situ polymerization-based coating (i.e., PU-11-3-3-CeO₂-P) showed similar self-healing properties. The PU-11-3-3-CeO₂-P coating also showed excellent UV shielding in real outdoor exposure conditions. Full article

A simple process to obtain a slippery surface with anti-ice and ice-phobic properties has been developed and characterized in laboratory. The coating is realized by growing a nanostructured pseudo-boehmite on an aluminum substrate and applying an environmentally compatible final functionalization consisting of a fluorine-free oligomeric short-chain alkylfunctional silane. The resulting surface is conceptually similar to a slippery liquid infused porous surface (SLIP) material, but the porous infrastructure is inorganic and the process to generate it is very simple, rapid and economic. The coating performance in terms of hydrophobicity at room and low temperatures, ice nucleation temperature and ice adhesion forces were assessed in laboratory. Moreover, hydrophobicity persistence was tested after prolonged immersion in acid, basic and saline solutions while the durability of ice-phobic behavior was assessed by repeated shear stress tests. Results are compared with those of a superhydrophobic hierarchical aluminum surface obtained with a fluorinated siloxane. The novel coating shows very good anti-ice properties and relevant durability, with some differences from the fluorinated surface. The novel slippery coating process is promising for industrial applications, also taking into account its environmental compatibility, simplicity and low cost. Full article