Search Results (447)

Plant Microbial Fuel Cells (PMFCs) represent a promising technology that uses electroactive bacteria to convert the chemical energy in organic matter into electrical energy. The addition of carbon pellet on electrodes may increase the specific surface area for colonization via bacteria. Use of nutrients such as urea could enhance plant growth. Our study aims to address the following questions: (1) Does carbon pellet layering affect the electrical performance of PMFCs? (2) Does urea treatment of the plants used to feed the PMFCs affect the electrical performance? A new prototype of PMFC has been tested: the plant pot is on the top, drainage water percolates to the tub below, containing the Microbial Fuel Cells (MFCs). To evaluate the best layering setup, two groups of MFCs were constructed: a “Double layer” group (with carbon pellet both on the cathode and on the anode), and a “Single layer” group (with graphite only on the cathode). All MFCs were plant-fed by Spathiphyllum lanceifolium L leachate. After one year, each of the previous two sets has been divided into two subsets: one wetted with percolate from plants fertilized with urea, and the other with percolate from unfertilized plants. Open circuit voltage (mV), short circuit peak current, and short circuit current after 5 s (mA) produced values that were measured on a weekly basis. PMFCs characterized by a “Single layer” group performed better than the “Double layer” group most times, in terms of higher and steadier values for voltage and calculated power. Undesirable results regarding urea treatment suggest the use of less concentrated urea solution. The treatment may provide consistency but appears to limit voltage and peak values, particularly in the “Double layer” configuration. Full article

Microalgae are promising candidates for renewable biofuel production and nutrient-rich animal feed. Cultivating microalgae using wastewater can lower production costs but often results in biomass contamination and increases downstream processing requirements. This study presents a novel system that integrates an algae cultivator (AC) with a single-chamber microbial fuel cell (MFC) equipped with photosynthetic and air-cathode functionalities, separated by a ceramic membrane. The system enables the generation of electricity and production of clean microalgae biomass concurrently, in both light and dark conditions, utilizing wastewater as a nutrient source and renewable energy. The MFC chamber was filled with simulated potato processing wastewater, while the AC chamber contained microalgae Chlorella vulgaris in a growth medium. The ceramic membrane allowed nutrient diffusion while preventing direct contact between algae and wastewater. This design effectively supported algal growth and produced uncontaminated, harvestable biomass. At the same time, larger particulates and undesirable substances were retained in the MFC. The system can be operated with synergy between the MFC and AC systems, reducing operational and pretreatment costs. Overall, this hybrid design highlights a sustainable pathway for integrating electricity generation, nutrient recovery, and algae-based biofuel feedstock production, with improved economic feasibility due to high-quality biomass cultivation and the ability to operate continuously under variable lighting conditions. Full article

The underutilization of fruit waste in agroindustry—particularly star fruit—leads to leachate generation, emissions, and disposal costs, highlighting the need for circular alternatives that treat organic fractions while producing energy. This study evaluated the bioelectrochemical conversion of carambola (Averrhoa carambola) residues in single-chamber microbial fuel cells (MFCs). Three 1000 mL reactors were constructed using carbon anodes and zinc cathodes, operated for 35 days with continuous voltage recording and daily monitoring of pH, conductivity, and ORP. Polarization curves were obtained, and FTIR and SEM analyses were conducted to characterize substrate transformation and anode colonization. The anodic biofilm was also profiled using metagenomics. Measurements were performed using calibrated electrodes and a data logger with one minute intervals. The systems exhibited rapid startup and reached peak performance on day 22, with a voltage of 1.352 V, current of 3.489 mA, conductivity of 177.90 mS/cm, ORP of 202.01 mV, and pH of 4.89. The V–I curve indicated an internal resistance of 16.51 Ω, and the maximum power density reached 0.517 mW/cm². FTIR revealed a reduction in bands associated with carbohydrates and proteins, consistent with biodegradation, while SEM confirmed extensive biofilm formation and increased anode surface roughness. Metagenomic analysis showed dominance of Acetobacter (59.35%), with Bacteroides (12.93%) and lactobacilli contributing to fermentative and electrogenic synergies. Finally, the series connection of three MFCs generated 2.71 V, sufficient to power an LED, demonstrating the feasibility of low-power applications and the potential for system scalability. Full article

Plastic pollution is an increasingly pressing environmental concern due to its persistence in ecosystems. To address this issue, this study evaluates polyethylene biodegradation and bioelectricity generation using Aspergillus ochraceopetaliformis in microbial fuel cells (MFCs). Single-chamber MFCs were designed (three) with carbon and zinc electrodes, where the fungus was cultivated in a nutrient-rich medium to enhance its metabolic activity. Parameters such as pH, power density, and FTIR spectra were monitored to assess plastic biodegradation. The results demonstrated a significant reduction in polyethylene mass and structure, along with a maximum generation of 0.921 V and 4.441 mA on day 26, with a power density of 0.148 mW/cm² and a current of 5.847 mA/cm². The optimal pH for fungal activity in the MFC was recorded at 7.059. Furthermore, FTIR analysis revealed a decrease in peak intensity at 1470 cm⁻¹ and 723 cm⁻¹, indicating structural modifications in the treated plastics. Furthermore, microbial fuel cells connected in series successfully powered an LED bulb, generating a maximum voltage of 2.78 V. These findings confirm the feasibility of using Aspergillus ochraceopetaliformis for biodegradation and bioelectricity generation, although practical applications require further optimization of system conditions and improvements in long-term stability. This research contributes to the development of biotechnological strategies for plastic waste management, sustainable integrating approaches with energy potential. Full article

This study discussed the influence of acetate and sodium chloride concentration on monitoring 2,4-dichlorophenol(2,4-DCP) by electroactive bacteria. The performance of the reactor was represented by power density, and the electrochemical activity was represented by redox capacity. At the same time, micro-electrodes were used to detect the redox potential between biofilms, and the changes in extracellular polymers and microbial community structure under different conditions were also explored. With acetate concentration of 1 g/L and sodium chloride concentration of 0.0125 g/L, the electroactive microorganisms were more sensitive to toxic substances and responded fast. The biofilm also evenly covered on the surface of the carrier, which aided in the diffusion of substances. Although the maximum power density monotonically increased with acetate concentration, high concentration of substrate may mask the inhibitory effect and affect the judgment of inhibitory results. The content of protein and polysaccharide increased monotonically with sodium chloride concentration. However, more polysaccharides would lead to high resistance to electron transfer. Compared to sodium chloride, the microbial content was more affected by acetate. The electroactive microorganisms had strong adaptability to salinity. In practical application, it is conducive to increase the sensitivity of MFCs to reasonably reduce the concentration of acetic acid and sodium chloride. Full article

This study reports the development of a simple and sensitive electrochemical sensor based on activated screen-printed electrodes modified by electrodeposition of nickel(II) tetrasulfonated phthalocyanine film (poly-NiTSPc), denoted SPE-A-polyNiTSPc, for the direct determination of BPA in landfill leachate samples. BPA concentrations in raw landfill leachate solutions and in residual solutions after a reverse osmosis (RO) treatment were determined, using differential pulse voltammetry (DPV) on SPE-A-polyNiTSPc, to be 29.7 mgL⁻¹ and 6.4 µgL⁻¹, respectively. The obtained BPA concentrations were very close to those found by the accredited lab in the same samples, which were 29.6 mgL⁻¹ and 6.0 µgL⁻¹, respectively. The applicability of SPE-A-polyNiTSPc for BPA bioremediation was investigated in landfill leachate samples using Trichoderma harzianum fungus in a microbial fuel cell (MFC), where the kinetics data were modeled. The first results showed an IC₅₀ of 175 mgL⁻¹ BPA, indicating that the inhibition factor could be negligeable for MFC experiments at 30 mgL⁻¹ BPA. The biodegradation kinetics was found to be of first order, with a kinetic constant of 0.795 h⁻¹ at 22 °C and a half-degradation time of 0.872 h for an initial concentration of 29 mgL⁻¹. The developed MFC displayed higher stability, offering a maximum power of 100 mWm⁻³. Full article

This study investigates microbial fuel cell (MFC) performance through the modification of Saccharomyces cerevisiae with gold nanoparticles (AuNPs) and polypyrrole (PPy). The yeast/AuNP-modified electrodes generated the highest median current of 2.57 nA, significantly outperforming the yeast/PPy-modified (0.82 nA) electrodes. Power density measurements further confirmed the superior performance of the yeast/AuNP-modified electrodes, showcasing a notable improvement in current densities and power outputs. Yeast/AuNP-modified graphite electrodes produced a higher power density of 22.8 mW/m², while exhibiting a lower current density compared to electrodes modified solely with yeast, which achieved a power density of 5.7 mW/m². These findings highlight the potential of AuNPs in significantly enhancing the electrochemical performance of yeast-based MFCs, providing a promising approach for the development of more efficient bioelectrochemical systems. Full article

Microbial fuel cells (MFCs) can have high pollutant removal efficiencies and generate electricity; however, the use of selective membranes represents a considerable expense. In this investigation, the performance of a membraneless MFC was evaluated at different hydraulic retention times (HRTs) of 12, 24, 36, and 48 h. The chemical oxygen demand removal efficiencies (CODREs) were 93.5, 90.9, 87.3, and 85.4%, and the biochemical oxygen demand (BODRE) values were 94.5, 91.5, 88.9, and 85.5 at HRTs of 48, 36, 24, and 12 h, respectively. Lower concentrations of solids (suspended solids and total dissolved solids), total nitrogen, phosphorus, fats and oils, and microbiological contamination (helminth eggs and fecal coliforms) were detected when operating the system at a 48 h HRT. At an HRT of 12 h, no decrease in electrical conductivity was detected, whereas at 48 h, it decreased by 19.6%. The oxidation–reduction potential and OCV increased at longer HRTs. The microorganisms detected at the anode were Achromobacter denitrificans, Achromobacter anxifer, and Pseudomonas aeruginosa. The 48 h HRT improved the chemical, physical, and microbiological quality of the municipal wastewater, favoring voltage generation. Full article

Wastewater treatment has become a priority in the global attempt to address environmental pollution. Conventional wastewater treatment processes are often limited by their high energy consumption, so it is necessary to develop new technologies. This work shows the results obtained using a passive aerated membraneless microbial fuel cell (PAML-MFC) system consisting of 10 individual units, designed to treat 1000 L/day of real wastewater, using granular activated carbon anodes and cathodes. The pilot-scale water treatment system under study combines design and materials to result in low-cost operation. After 300 days of treating real wastewater originally characterized by a chemical oxygen demand (COD) value of 500 mg/L on average, it was found that the PAML-MFC under study removed 60 to 80% of the COD contained in real wastewater. Under these conditions, the individual MFCs reached an average power density below 1 mW/m³. Full article

Microbial fuel cells (MFCs) are one of the contributors to the novel sustainable energy generation from organic waste. However, the application of MFCs is limited due to the slow charge transfer between cells and electrodes. This problem can be solved by modifying cells with conductive polymers, such as polypyrrole (PPy). We investigated the viability and electroactivity of modified cells at five different pyrrole concentrations, namely 8, 25, 50, 100, and 200 mM. The 100 mM concentration of PPy solution had the highest impact on yeast cells’ proliferation and growth, with the CFU/mL of PPy-treated yeast cells being 0.6 × 10⁷ ± 5 × 10⁻². The power density of the constructed MFC was evaluated by using an external load. The MFCs were analyzed using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Although CV results with different pyrrole concentrations were similar, DPV indicated that yeast modification with 50 mM pyrrole resulted in the most significant current density, which may be attributed to an increase in charge transfer due to the conductive properties of polypyrrole. The power density achieved with modified yeast in wastewater, 12 mW/m², reached levels similar to those in laboratory solutions, 45 mW/m². Full article

Microbial fuel cells (MFCs) are bio-electrochemical systems that harness microorganisms to convert organic pollutants in wastewater directly into electricity, offering a dual solution for sustainable wastewater treatment and renewable energy generation. This paper presents a holistic techno-economic and environmental feasibility assessment of large-scale MFC deployment in Dhaka’s industrial zone, Bangladesh, as a relevant case study. Here, treating 100,000 cubic meters of wastewater daily would require a capital investment of approximately USD 500 million, with a total project cost ranging between USD 307.38 million and 1.711 billion, depending on system configurations. This setup has an estimated theoretical energy recovery of 478.4 MWh/day and a realistic output of 382 MWh/day, translating to a per-unit energy cost of USD 0.2–1/kWh. MFCs show great potential for treating wastewater and addressing energy challenges. However, this paper explores remaining challenges, including high capital costs, electrode and membrane inefficiencies, and scalability issues. Full article

This study focuses on electrical stimulation for composting. Using the PSALSAR method, a comprehensive systematic review analysis identified 22 relevant articles. The examined studies fall into four main systems: electric field-assisted aerobic composting (EAAC), electrolytic oxygen aerobic composting (EOAC), microbial fuel cells (MFCs), and thermoelectric generators (TEGs). Apart from the main systems highlighted above, bioelectrochemically assisted anaerobic composting (AnC_{BE, III}) is discussed as an underexplored system with the potential to improve the efficiency of anaerobic degradation. Each system is described in terms of key materials, composter design, operating conditions, temperature evolution, compost maturity, microbial community, and environmental outcomes. EAAC and EOAC systems accelerate organic matter decomposition by improving oxygen distribution and microbial activity, whereas MFC and TEG systems have dual functioning due to the energy generated alongside waste degradation. These innovative systems not only significantly improve composting efficiency by speeding up organic matter breakdown and increasing oxygen supply but also support sustainable waste management by reducing greenhouse gas emissions and generating bioelectricity or heat. Together, these systems overcome the drawbacks of conventional composting systems and promote future environmental sustainability solutions. Full article

This study introduces an advanced strategy for improving microbial fuel cell (MFC) performance in hexavalent chromium (Cr(VI)) wastewater treatment. A high-performance nano-iron sulfide (nano-FeS) hybridized biocathode was developed by regulating glucose concentration and applying an external voltage. The combination of a glucose concentration of 1000 mg/L and a 0.2 V applied voltage greatly promoted the in situ biosynthesis of nano-FeS, resulting in smaller particle sizes and increased quantities within the biocathode, leading to enhanced electrochemical performance. The MFC with the hybridized biocathode exhibited the highest power density (43.45 ± 1.69 mW/m²) and Cr(VI) removal rate (3.99 ± 0.09 mg/L·h), outperforming the control by 29% and 71%, respectively. The improvements were attributed to the following processes. (1) Nano-FeS provided additional active sites that enhanced electron transfer and electrocatalytic activity, reducing cathode passivation; (2) it protected microorganisms by reducing Cr(VI) toxicity, promoting redox-active substance enrichment and antioxidant enzyme secretion, which maintained microbial activity; (3) the biocathode selectively enriched electroactive and Cr(VI)-reducing bacteria (such as Brucella), fostering a stable and symbiotic microbial community. This study highlights the promising potential of regulating carbon source and external voltage to boost nano-FeS biosynthesis, offering a sustainable and efficient strategy for MFC-based Cr(VI) wastewater treatment with practical implications. Full article

This study systematically compares the environmental and economic performance of three wastewater treatment systems: constructed wetlands (CWs), microbial fuel cells (MFCs), and their integration (CW–MFC). Lab-scale units of each system were constructed using a multi-media matrix (gravel, zeolite, and granular activated carbon), composite native wetland species (Juncus effusus, Iris sp., and Typha angustifolia), carbon-based electrodes (graphite), and standard inoculum for CW and CW–MFC. The MFC system employed carbon-based electrodes and proton-exchange membrane. The experimental design included a parallel operation of all systems treating domestic wastewater under identical hydraulic and organic loading rates. Environmental impacts were quantified across construction and operational phases using life cycle assessment (LCA) with GaBi software 9.2, employing TRACI 2021 and ReCiPe 2016 methods, while techno-economic analysis (TEA) evaluated capital and operational costs. The key results indicate that CW demonstrates the lowest global warming potential (142.26 kg CO₂-eq) due to its reliance on natural biological processes. The integrated CW–MFC system achieved enhanced pollutant removal (82.8%, 87.13%, 78.13%, and 90.3% for COD, NO₃, TN, and TP) and bioenergy generation of 2.68 kWh, balancing environmental benefits with superior treatment efficiency. In contrast, the stand-alone MFC shows higher environmental burdens, primarily due to energy-intensive material requirements and fabrication processes. TEA results highlight CW as the most cost-effective solution (USD 627/m³), with CW–MFC emerging as a competitive alternative when considering environmental benefits and operational efficiencies (USD 718/m³). This study highlights the potential of hybrid systems, such as CW–MFC, to advance sustainable wastewater treatment technologies by minimizing environmental impacts and enhancing resource recovery, supporting their broader adoption in future water management strategies. Future research should focus on optimizing materials and energy use to improve scalability and feasibility. Full article

Microbial Fuel Cell (MFC) is a novel bioelectrochemical system that catalyzes the oxidation of chemical energy in organic waste and converts it directly into electrical energy through the attachment and growth of electroactive microorganisms on the electrode surface. This technology realizes the synergistic effect of waste treatment and renewable energy production. A CF-NiO-PANI capacitor composite anode was prepared by loading polyaniline on a CF-NiO electrode to improve the capacitance of a CF electrode. The electrochemical characteristics of the composite anode were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), and the electrode materials were analyzed comprehensively by scanning electron microscopy (SEM), energy diffusion spectrometer (EDS), and Fourier transform infrared spectroscopy (FTIR). MFC system based on CF-NiO-PANI composite anode showed excellent energy conversion efficiency in potato starch wastewater treatment, and its maximum power density increased to 0.4 W/m³, which was 300% higher than that of the traditional CF anode. In the standard charge–discharge test (C1000/D1000), the charge storage capacity of the composite anode reached 2607.06 C/m², which was higher than that of the CF anode (348.77 C/m²). Microbial community analysis revealed that the CF-NiO-PANI anode surface formed a highly efficient electroactive biofilm dominated by electrogenic bacteria (accounting for 47.01%), confirming its excellent electron transfer ability. The development of this innovative capacitance-catalytic dual-function anode material provides a new technical path for the synergistic optimization of wastewater treatment and energy recovery in MFC systems. Full article