Search Results (3)

Thermoelectric nanoantennas have been extensively investigated due to their ability to directly convert infrared (IR) radiation into direct current without an additional rectification device. In this study, we introduce a thermoelectric nanoantenna geometry for maximum output voltage (V_oc) and propose an optimal series array configuration with a finite number of antennas to enhance the V_oc. A finite and open-ended SiO₂ substrate, with a thickness of a quarter-effective wavelength at a frequency of 28.3 THz, is used to generate standing waves within the substrate. An array of antennas is then positioned optimally on the substrate to maximize the temperature difference ($∆T$) between hot and cold areas, thereby increasing the average V_oc per antenna element. In numerical simulations, a linearly polarized incident wave with a power density of 1.42 W/cm² is applied to the structure. The results show that a single antenna with the optimum geometry on a substrate measuring 35 µm × 35 µm generates a $∆$T of 64.89 mK, corresponding to a V_oc of 1.75 µV. Finally, a series array of 5 × 6 thermoelectric nanoantennas on a 150 µm × 75 µm substrate including measurement pads achieves an average $∆$T of 49.60 mK with a total V_oc of 40.18 µV, resulting in an average V_oc of 1.34 µV per antenna element and a voltage responsivity (β_v) of 0.77 V/W. This value, achieved solely by optimizing the antenna geometry and open-ended substrate, matches or exceeds the V_oc and β_v of approximately 1 µV and 0.66 V/W, respectively, from suspended thermoelectric antenna arrays over air cavities. Therefore, the proposed thermoelectric nanoantenna array device, characterized by high stability and ease of fabrication, is suitable for manufacturing massive nanoantenna arrays for high-output IR-DC energy harvesters. Full article

This paper presents the results of beam investigations on semiconductor IR lasers using novel detectors based on thermocouples. The work covers the design, the fabrication of detectors, and the experimental validation of their sensitivity to IR radiation. The principle of operation of the manufactured detectors is based on the Seebeck effect (the temperature difference between hot and cold junctions induced voltage appearance). The devices were composed of several thermocouples arranged in a linear array. The nano- and microscale thermocouples (the hot junctions) were fabricated using a typical Si-compatible MEMS process enhanced with focused ion beam (FIB) milling. The performance of the hot junctions was tested, focusing on their sensitivity to IR radiation covering the near-infrared (NIR) radiation (λ = 976 nm). The output voltage was measured as a function of the detector position in the XY plane. The measurement results allowed for reconstructing the Gaussian-like intensity distribution of the incident light beam. Full article

The focused ion beam (FIB) technique was used to fabricate a nanothermocouple (with a 90 nm wide nanojunction) based on a metal–semiconductor (Pt–Si) structure, which showed a sensitivity up to 10 times larger (with Seebeck coefficient up to 140 µV/K) than typical metal–metal nanothermocouples. In contrast to the fabrication of nanothermocouples which requires a high-tech semiconductor manufacturing line with sophisticated fabrication techniques, environment, and advanced equipment, FIB systems are available in many research laboratories without the need for a high-tech environment, and the described processing is performed relatively quickly by a single operator. The linear response of the manufactured nanothermocouple enabled sensitive measurements even with small changes of temperature when heated with a stream of hot air. A nonlinear response of the nanothermocouple (up to 83.85 mV) was observed during the exposition to an argon-laser beam with a high optical power density (up to 17.4 Wcm⁻²), which was also used for the laser annealing of metal–semiconductor interfaces. The analysis of the results implies the application of such nanothermocouples, especially for the characterization of laser beams with nanometer spatial resolution. Improvements of the FIB processing should lead to an even higher Seebeck coefficient of the nanothermocouples; e.g., in case of the availability of other suitable metal sources (e.g., Cr). Full article