Search Results (2,308)

Well-killing operations in water-sensitive hydrophilic formations are often complicated by extended well clean-up periods and, in some cases, failure to restore the well’s production potential post-kill. Typical development targets exhibiting these properties include the Neocomian and Jurassic deposits of fields in Western Siberia and Western Kazakhstan. This paper proposes a well-killing method incorporating simultaneous near-wellbore treatment. In cases where heavy oil components (asphaltenes, resins, or paraffins) are deposited in the near-wellbore zone, their removal with a solvent results in post-operation flow rates that exceed pre-restoration levels. For wells not affected by asphaltene, resin, and paraffin deposits, killing is performed using a blocking pill of invert emulsion stabilized with an emulsifier and hydrophobic nanosilica. During filtration into the formation, this emulsion does not break but rather reforms according to the pore throat sizes. Flow rates in such wells typically match pre-restoration levels. The described engineering solution proves less effective when the well fluid water cut exceeds 60%. For wells exhibiting premature water breakthrough that have not yet produced their estimated oil volume, the water source is identified, and water shutoff operations are conducted. This involves polymer-gel systems crosslinked with resorcinol and paraform, reinforced with inorganic components such as chrysotile microdispersions, micro- and nanodispersions of shungite mineral, and gas black. Oscillation testing identified the optimal additive concentration range of 0.6–0.7 wt%, resulting in a complex modulus increase of up to 25.7%. The most effective polymer-inorganic composite developed by us, incorporating gas black, demonstrates high water shutoff capability (residual resistance factor ranges from 12.5 to 65.0 units within the permeability interval of 151.7 to 10.5 mD). Furthermore, the developed composites exhibit the ability to selectively reduce water permeability disproportionately more than oil permeability. Filtration tests confirmed that the residual permeability to oil after placing the blocking composition with graphene is 6.75 times higher than that to water. Consequently, such treatments reduce the well water cut. Field trials confirmed the effectiveness of the developed polymer-inorganic composite systems. Full article

Agricultural and food by-products offer valuable opportunities for circular and bio-based innovation across sectors. In the textile industry, replacing fossil-based coatings with sustainable alternatives is increasingly urgent. This study evaluates the performance of a textile coating based on coffee silverskin (CS)—an abundant by-product of coffee roasting—applied to four natural fibre substrates: cotton, lyocell, wool, and silk. A formulation combining 60% CS sludge (8% solids), treated by wet ball milling, with an aliphatic polyester-polyurethane dispersion was applied via knife coating. Standardised tests assessed mechanical resistance, air permeability, colour fastness, moisture management, and water repellency, including contact angle and drop absorption analyses. Results revealed that all substrates were compatible with the CS-based coating, which reduced air permeability and increased hydrophobicity. Notably, silk showed the most significant functional enhancement, transitioning from hydrophilic to waterproof with increased durability—indicating strong potential for technical applications such as outerwear and performance textiles. Given the renewable origin of both the substrate and coating, this study highlights the feasibility of valorising agri-food waste in high-performance, bio-based textile systems. These findings demonstrate the potential of CS as a bio-based coating for technical textiles, supporting the development of high-performance and sustainable materials within the textile industry. Full article

This study describes the modification of polyamide fabric with the commercial name Cordura to create a material that is more resistant to the permeation of toxic gases and compound vapors while remaining permeable to water vapor and air. The surface of Cordura was modified by applying a very thin film, deposited from a vapor organic phase at room temperature under the influence of γ-radiation. The permeability of the modified fabric to water vapor, organic vapors, organic dyes, and toxic substances (sulfur mustard gas) was determined and compared to the properties of the unmodified fabric. Full article

Prolonged exposure to landfill leachate can weaken the impermeability of liner systems, leading to leachate leakage and the contamination of surrounding soil and water. To improve loess impermeability to enable its use as a liner material, this study uses synthetic landfill leachate to investigate its effects on loess permeability via a series of laboratory tests. This study focused on the influence of varying dosages of calcium lignosulfonate (CLS) on loess permeability, along with its capacity to adsorb and immobilize heavy metal ions. Microscale characterization techniques, including Zeta potential analysis, X-ray fluorescence spectroscopy (XRF), and scanning electron microscopy (SEM), were employed to investigate the impermeability mechanisms of CLS-modified loess and its adsorption behavior toward heavy metals. The results indicate that the permeability coefficient of loess decreases significantly with increasing compaction, while higher leachate concentrations lead to a notable increase in permeability. At a compaction degree of 0.90, the permeability coefficient was reduced to 8 × 10⁻⁸ cm/s. In contrast, under conditions of maximum leachate concentration, the permeability coefficient rose markedly to 1.5 × 10⁻⁴ cm/s. Additionally, increasing the dosage of the compacted loess stabilizer (CLS) effectively reduced the permeability coefficient of the modified loess to 7.1 × 10⁻⁵ cm/s, indicating improved impermeability and enhanced resistance to contaminant migration. With the prolonged infiltration time of landfill leachate, the removal efficiency of Pb²⁺ gradually decreases and stabilizes, while the Pb²⁺ removal efficiency of the modified loess increased by approximately 40%. CLS-modified loess, through multiple mechanisms, reduces the fluid flow pathways and enhances its adsorption capacity for Pb²⁺, thereby improving the soil’s protection against heavy metal contamination. While these results demonstrate the potential of CLS-modified loess as a sustainable landfill liner material, the findings are based on controlled laboratory conditions with Pb²⁺ as the sole target contaminant. Future work should evaluate long-term performance under field conditions, including seasonal wetting–drying and freeze–thaw cycles, and investigate multi-metal systems to validate the broader applicability of this modification technique. Full article

This study incorporates a nonlinear seepage relationship into Biot’s consolidation theory and simulates the consolidation of a single vertical drain under vacuum preloading using the finite element method. The model, simplified via the equal-strain assumption, is validated against theoretical predictions. Under the axisymmetric Biot’s framework, consolidation behavior is analyzed in detail. The results show that in the early stages of consolidation, excess pore water pressure in the vicinity of the prefabricated vertical drain (PVD) does not fully dissipate and may even increase, indicating the occurrence of the Mandel–Cryer effect. As the consolidation process advances, the consolidation front gradually extends outward, and the void ratio near the PVD decreases rapidly, leading to the formation of a clogging zone. In contrast, the reduction in the void ratio in the non-clogging region is relatively slow. The progressive development of the clogging zone significantly impedes the overall consolidation rate. Furthermore, this study explores the influence of key parameters—including the compression index, permeability coefficient, well diameter ratio, smear effect, and well resistance—on the formation of the clogging zone and the Mandel–Cryer effect. Full article

Background/Objectives: Resistance of pathogenic microorganisms to antibiotics poses a serious threat to public health and often leads to devastating consequences. In this context, one of the pressing challenges in pharmacochemistry is the search for new, effective antibiotics to combat severe human diseases. Cyclic lipopeptides have emerged as some of the most promising candidates and have been widely studied. These compounds are a class of microbial secondary metabolites produced by various microorganisms, and they possess significant medical and biotechnological importance. The defining structural feature of these compounds is the presence of both a hydrophobic fragment, primarily a hydrocarbon tail of varying length, and a hydrophilic cyclic peptide moiety. This hydrocarbon tail confers amphiphilic properties to the lipopeptides, which are essential for their broad spectrum of biological activities. Their mechanism of action involves disruption of the cell membrane, and in many cases, the formation of ion-permeable defects has also been shown. Results: This review summarizes the data on cyclic lipopeptides produced by Pseudomonas spp., Streptomyces spp., and Bacillus spp. that modify membrane permeability through the formation of ion channels. The main emphasis is on understanding how the structure of the CLP can be related to the probability and mode of pore formation. Conclusions: The findings can contribute to expanding the arsenal of effective antimicrobial agents with a mechanism of action that reduces the risk of developing resistance. Full article

Reinforced concrete is the most widely utilized building material for bridges, buildings, and other infrastructure components, and its longevity is significantly influenced by corrosion or rust. Corrosion shortens reinforced concrete’s service life and safety, which raises maintenance expenses. Concrete is a porous material that allows air and water to pass through, and corrosion begins when the air and water reach the steel. This study evaluated the mechanical and corrosion resistance properties of reinforced concrete containing recycled and supplemented cementitious materials. The results showed that mixtures containing fine glass aggregate, glass powder, slag, fly ash, or silica fume significantly improved the compressive, tensile, and flexural strengths, but the 10% slag mix, and 5% glass aggregate with 10% glass powder with 10% fly ash mix produced the best results overall. In addition, the mixture containing 15% fly ash produced the best result against corrosion. The corrosion tests revealed that mixtures with 10% slag and 20% glass powder also significantly enhanced the corrosion resistance of steel with the same results, confirming their effectiveness in reducing the permeability and increasing the durability of reinforced concrete. Full article

Asphalt pavements are widely used in airports due to their excellent skid resistance, vibration damping, and ease of construction. However, traditional fog seal materials often suffer from insufficient adhesion between fine sand and the emulsified asphalt binder, resulting in limited durability of the maintenance effect. This study aims to optimize the design of traditional fog seal materials and systematically evaluate their surface and durability performance. Firstly, a composite modified emulsified asphalt was prepared as the sand suspension slurry for the sand-containing fog seal. Through the dry wheel abrasion test, the optimal fine aggregates content was determined for four different spraying amounts (0.8, 0.9, 1.0, and 1.1 kg/m²). When the proportion of fine aggregates increases, the spraying amount needs to be increased accordingly to ensure the wrapping effect. Subsequently, pavement performance evaluation was conducted based on several indicators, including surface curing time, British Pendulum Number (BPN) friction coefficient, permeability coefficient, and mass loss rate. The results showed that the designed sand-containing fog seal significantly reduced surface curing time and exhibited superior skid resistance and permeability property compared to styrene-butadiene rubber (SBR)-modified emulsified asphalt. After freeze–thaw cycles, the maximum decrease in friction coefficient was 10.2%, and the mass loss rate after abrasion was approximately 67%, which were lower than those of SBR-modified emulsified asphalt (22.2% and 81%, respectively). Finally, considering the comprehensive performance comparison and evaluation, the optimal mix proportion was determined as 1.0 kg/m² spraying amount with 30% fine aggregates content. The findings of this study provide practical support for improving the durability and service life of airport asphalt pavements. Full article

Steel fiber reinforced concrete in marine environments often suffers from stress corrosion coupling. Under mechanical loading, the formation of penetrating cracks in the matrix increases susceptibility to seawater penetration and interfacial degradation. Using molecular dynamics simulations, this study investigated the effects of calcium-to-silicon (Ca/Si) ratios on the interfacial bonding and transport properties of a γ-FeOOH/CSH system. The results show that higher Ca/Si ratios strengthen ionic bonding between CSH and γ-FeOOH, thereby improving interfacial adhesion. Additionally, increased Ca/Si ratios significantly slow the transport of water molecules and ions (Na⁺, Cl⁻, SO₄²⁻) within γ-FeOOH/CSH nanopores. It was observed that Cl⁻ and SO₄²⁻ exhibited pronounced filtration effects at Ca/Si = 2.0. These findings suggest that optimizing the Ca/Si ratio in concrete can simultaneously enhance interfacial strength and reduce permeability. This provides an effective strategy for improving the marine erosion resistance of steel fiber reinforced concrete structures. Full article

The shelf life of perishable foods is traditionally determined by microbiological, chemical, and sensory analyses, which are well-established and reliable. However, these methods can be time-consuming and resource-intensive, and they may not fully account for unexpected storage deviations, such as temperature fluctuations or equipment failures. Smart films emerge as a promising alternative, enabling rapid, visual, and low-cost food quality monitoring. This study developed smart films based on zein/gelatin/cellulose nanocrystals (Z/G/CNC) functionalized with alizarin (AL, 0–3% w/w), produced by casting (12.5% zein, 12.5% gelatin, and 5% CNC w/w). The films were characterized for morphological, physicochemical, thermal, and spectroscopic properties, chromatic response at pH 3–11, activity against Escherichia coli and Staphylococcus aureus, and applicability in monitoring Merluccid hake fillets. The incorporation of AL reduced water solubility, increased water vapor permeability and contact angle, imparted a more intense orange coloration, and improved thermal resistance. AL also increased thickness and elongation at break while reducing tensile strength and Young’s modulus. All films exhibited excellent UV-blocking capacity (<1% transmittance). Noticeable color changes were observed, with the Z/G/CNC/AL1 film being the most sensitive to pH variations. During Merluccid hake storage, ΔE values exceeded 3 within 72 h, with a color change from orange to purple, correlating with fillet pH (8.14) and total volatile basic nitrogen (TVB-N) (24.73 mg/100 g). These findings demonstrate the potential of the developed films as biodegradable sensors for smart packaging of perishable foods. Full article

Vertical low-permeability barriers are widely used to improve the stability and seepage resistance of flood embankments. The present study evaluates three barrier technologies—vibrating beam slurry walls (VBSWs), deep soil mixing (DSM), and low-pressure grout injection (LPG)—through a series of consolidated drained triaxial tests and permeability coefficient tests on soil samples collected from the sites where different barrier installation technologies were used. All three barrier installation methods produced substantial improvements in both mechanical and hydraulic performance: the effective angle of internal friction (φ′) increased by 3–6° in samples with a plasticity index near 3.5%, and coefficients of permeability dropped from 10⁻⁸–10⁻⁷ m/s in untreated soils to below 10⁻⁹ m/s in treated specimens. The key finding of the study is that the barrier performance varies by the technology and the soil type. According to the result, DSM is the most effective technology used in clay-rich soils (φ′ increased up to 4°); LPG achieved the lowest permeability (7 × 10⁻¹¹ m/s) in granular soils; and VBSWs balanced strength and impermeability, most effective in silty sands. Flow-pump tests further demonstrated that treated soils required much longer to stabilize under a constant flow rate and could sustain higher hydraulic gradients before reaching equilibrium. These findings show the importance of matching barrier technology to soil plasticity and liquidity characteristics and highlight saturation as essential for reliable laboratory evaluation. The results provide a scientific basis for selecting and designing vertical barriers in flood-preventing infrastructure, offering performance benchmarks for improving hydraulic and geotechnical structures. Full article

Membrane technology is widely used in gas separation processes due to its small footprint, high energy efficiency, and favorable economic viability. The current membrane market predominantly relies on polymer membranes, among which polyimide (PI) membranes stand out as highly promising materials due to their superior gas separation performance coupled with exceptional thermal and chemical stability. However, traditional polyimide membranes suffer from low gas permeability and insufficient plasticization resistance, hindering their broader industrial application. In order to meet the demands of more stringent application fields, it is crucial to further improve their gas performance and anti-plasticization to enhance their cost-effectiveness. Consequently, it is essential to modify traditional polyimides and formulate membrane fabrication strategies to solve these problems. This review introduces the monomer structures and synthesis approaches of polyimides, including solution-based and solid-state thermal condensation. Then, we propose representative preparation methods of polyimide-based membranes. Additionally, modification strategies, including thermal rearrangement, cross-linking, and physical blending, are summarized, which address the critical issues in contemporary polyimide-based gas separation membranes. Finally, this review critically discusses the current challenges and prospects for developing polyimide membranes for gas separation. Full article

The growing threat of antimicrobial resistance drives the need for innovative and multifunctional therapeutic systems. In this study, a controlled-release system based on a bioactive film composed of gelatin, bacterial cellulose (BC), sericin, citric acid, PEG 400, and nisin was developed for topical applications in infected wound treatment. BC membranes were produced using Komagataeibacter xylinus and enzymatically treated to optimize dispersion within the polymer matrix. The resulting system exhibited a semi-rigid, homogeneous morphology with appropriate visual characteristics for dermatological use. Microbiological assays demonstrated significant antimicrobial activity against Gram-positive (Staphylococcus aureus) and resistant Gram-negative strains (Escherichia coli and Enterobacter cloacae), attributed to the synergistic action of nisin and citric acid, which enhanced bacterial outer membrane permeability. The antioxidant capacity was confirmed through DPPH radical scavenging assays, indicating a progressive release of bioactive compounds over time. Scanning electron microscopy (SEM) analyses revealed good integration of biopolymers within the matrix. These results suggest that the strategic combination of natural biopolymers and antimicrobial agents produced a functional system with improved mechanical properties, a broadened antimicrobial spectrum, and promising potential as a bioactive wound dressing for the treatment of infected skin lesions. Full article

Xylazine (XYL), an FDA-approved veterinary tranquilizer, is being abused both as an opioid adulterant in a street-drug known as “Tranq-dope” and as a date rape drug. Given its now nearly ubiquitous use with fentanyl and fentanyl derivatives across the globe, XYL has become a primary target for researchers seeking to develop portable and cost-effective sensors for its detection. Electrochemical sensors based on the oxidation of XYL, while useful, have limitations due to certain interferents and inherent electrode fouling that render the approach less reliable, especially in certain sample matrices. In this work, modified electrode platforms incorporating layers of multi-walled carbon nanotubes for sensitivity along with semi-permeable polyurethane (PU) layers and host–guest chemistry using β-cyclodextrin for selectivity are deployed for XYL detection using complementary adsorptive cathodic stripping analysis. The modified electrode sensors are optimized to minimize high potentials and maintain fouling resistant capabilities and investigated to better understand the function of the PU layer. The use of adsorptive cathodic stripping differential pulse voltammetry indirectly indicates the presence and concentration of XYL within complex sample media (beverages and synthetic urine). When used in this manner, the modified electrodes exhibited an overall average sensitivity of ~35 (±9) nA/μM toward XYL with a limit of quantification of <10 ppm, while also offering adaptability for the analysis of XYL in different types of samples. By expanding the capability of these XYL sensors, this study represents another facet of tool development for use by medical professionals, first-responders, forensic investigators, and drug-users to limit exposure and help stem the dangerous and illegal use of XYL. Full article

Background: Acute lung injury (ALI) and its severe form, acute respiratory distress syndrome (ARDS), are critical conditions lacking effective pharmacologic therapies. Lipopolysaccharide (LPS), a bacterial endotoxin, is a well-established trigger of ALI. Emerging evidence suggests that heparin derivatives may attenuate lung injury, but their mechanisms remain unclear. Methods: This study evaluated the protective effects of 2-O, 3-O desulfated heparin (ODSH) in a murine model of LPS-induced ALI. Mice received LPS intratracheally with or without ODSH pre-treatment. Lung injury was assessed by bronchoalveolar lavage fluid (BALF) analysis, Evans blue dye albumin EBDA) extravasation, and histopathology. Results: ODSH treatment significantly reduced BALF protein concentration, inflammatory cell infiltration, and EBDA leakage. ODSH preserved endothelial barrier function in vitro, as evidenced by transendothelial electrical resistance (TER) measurements in human lung microvascular endothelial cell (HLMVEC) monolayers. Histological assessment (H&E staining) and myeloperoxidase (MPO) staining demonstrated reduced lung injury and neutrophil infiltration in the ODSH group. ODSH also downregulated pro-inflammatory mediators (NF-κB, IL-6, p38 MAPK) and upregulated the anti-inflammatory cytokine IL-10. Conclusions: ODSH mitigates LPS-induced ALI by reducing vascular permeability, neutrophilic inflammation, and pro-inflammatory signaling while enhancing IL-10 expression. These findings suggest ODSH may offer a novel therapeutic approach for treating ALI. Full article