Search Results (1,571)

This study investigates the combined effects of thermal and moisture aging on PVC-insulated low voltage (LV) photovoltaic (PV) cables using an accelerated-aging design to represent realistic PV operating conditions commonly encountered in hot and humid climates. Thermal aging was carried out at 90 °C for five aging cycles, with each thermal cycle followed by controlled moisture injection to simulate moisture stress. The degradation behavior was evaluated using broadband dielectric spectroscopy, FTIR analysis, and Shore D hardness measurements. Changes in dielectric dissipation factor (tanδ) and real permittivity (${\epsilon }^{\prime }$) were analyzed over a wide frequency range, with 100 kHz selected for its high sensitivity to aging-induced oxidation-related dipolar and interfacial polarization mechanisms. Degradation indices (DI) and degradation rates (DR) were derived from tanδ and correlated with mechanical and chemical changes. The results showed a 5% and 7% increase in tanδ at 100 kHz and in hardness, respectively, with decreases of 68% and 75% in the carbonyl and hydroxyl indices, respectively. Three distinct aging stages were identified: early thermo-oxidation with limited functional impact; mid-stage dehydrochlorination and moisture interaction; and late-stage chain scission, plasticizer loss, and insulation stiffening. The findings demonstrate the importance of climate-specific aging assessment and confirm the effectiveness of integrated electrical, mechanical, and chemical diagnostics for PV cable condition monitoring. Full article

This study aims to evaluate the use of Tectona grandis sawdust (Teak) and activated carbons (ACs) prepared from Teak and modified with urea on the removal of methylene blue (MB) from the aqueous phase. Activation is performed with potassium hydroxide (KOH), and urea is added during chemical activation to increase nitrogen content in the AC matrix and improve textural properties. ACs are physiochemically characterized by elemental and Fourier Transform Infrared (FTIR) spectroscopy analysis, with the determination of the point of zero charge (pHpzc) and nitrogen adsorption at 77 K. The addition of urea allows for obtaining ACs with a higher pHpzc and carbon and nitrogen content, with improved textural properties when compared with the original AC. The addition of urea also promotes an increase in surface area and porous volume (1246 m² g⁻¹ and 0.64 cm³ g⁻¹). The modifications slightly affect the performance of the ACs in removing MB from water. While the original AC (AC_Teak_KOH_1_2) has a maximum MB adsorption capacity of 270.2 mg g⁻¹, the modified one (AC_Teak_KOH_urea (1_2_1)) has a maximum adsorption capacity of 281.7 mg g⁻¹. MB adsorption isotherms fit well with the Freundlich equation. Kinetic data fit well with the pseudo-second-order model, and the Weber–Morris representation shows that MB adsorption is described as a succession of two diffusion steps. The results make clear that it is possible to recover Teak waste through its transformation into ACs, presenting high application in the removal of dyes from water. Full article

Increasing global demand for animal-based protein has created a critical environmental management challenge regarding manure accumulation in intensive livestock production. Gasification offers a sustainable solution by converting organic residues into renewable synthetic gas (syngas) and carbon-rich biochar. This study systematically evaluated the performance of three major types of animal waste—dairy manure, poultry litter, and swine manure—against a lignocellulosic control (wood veneer waste) in a top-lit updraft (TLUD) gasifier. Three airflow rates (10, 15, and 20 L min⁻¹) were studied. The results indicated that increasing airflow significantly elevated the gasifier flame front temperatures, with poultry litter achieving the highest peak temperature (825.5 °C), followed by swine manure and dairy manure (753.7 and 727.0 °C, respectively) at 20 L min⁻¹ airflow. While dairy manure exhibited the fastest linear burning rate (25.7 mm/min), poultry litter demonstrated the highest mass consumption rate (32.8 g/min). Feedstock chemistry drove distinct reaction pathways in syngas composition. Poultry litter emerged as the superior feedstock for H₂ production, achieving a peak H₂ concentration of 10.78% at 20 L min⁻¹, which attributed to a synergistic combination of outstanding temperature, moisture content and catalytic alkali metals that promoted steam reforming and water–gas shift reactions. CO production was dominated by wood veneer (17.6%), which was driven by the dominance of elemental carbon and fixed solid (FS) content that favored partial oxidation and a Boudouard reaction. These findings suggest that while airflow regulates thermal kinetics, the specific energy profile of the produced syngas is fundamentally determined by the physiochemical properties of the biomass precursor. Full article

This study compared the physicochemical and biological properties of Bio-C Repair (BR), a new putty-type calcium silicate-based material, with ProRoot MTA (P) and Super-Bond (SB). Discs of the three materials were prepared. Human periodontal ligament cells were seeded onto the discs, and metabolic activity was assessed by MTT assay on days 7 and 28; cells without discs served as the negative control (NC). Moreover, the pH and calcium ion concentration of the eluate, the mass change, and the water sorption were investigated. On day 7, BR showed significantly lower cell activity than P and NC. However, by day 28, BR activity increased significantly, with no significant difference relative to other groups, whereas P activity was significantly suppressed relative to SB and NC. Physiochemically, BR maintained a significantly higher alkalinity (pH ~11.0) and greater calcium ion release than P throughout the 28 days. Furthermore, BR exhibited significant mass gain (15.7%) and the highest water sorption (15.4%), whereas P showed mass loss (−1.1%). Although the high pH of BR initially suppressed cell activity, it demonstrated favorable cytocompatibility by day 28. BR showed a significantly improved long-term cellular response compared to P, suggesting it is a promising alternative as a root-end filling material. Full article

Zosteric acid (ZA) is a marine-derived phenolic sulfate with great application potential as a natural antifouling agent in food safety. This review provides a comprehensive overview of ZA, focusing on its physio-chemical properties, structure–function relationships, and antifouling mechanisms, with particular emphasis on its relevance to controlling biofilms associated with food spoilage and foodborne contamination. It further discusses the major production strategies for ZA, including natural extraction, chemical synthesis, enzymatic synthesis, and microbial biosynthesis. Key challenges related to production efficiency, process scalability, and regulatory compliance are critically analyzed. Finally, future perspectives are proposed for the development and application of ZA in food processing, packaging, and hygiene control, with emphasis on integrating sustainable biosynthesis with practical implementation in food-related environments. This review aims to provide valuable insights that support the development of natural, safe, and sustainable antifouling strategies to enhance food safety and quality. Full article

To identify a suitable plastic film type for broccoli cultivation in the subtropical humid region of southern China, a field experiment was conducted with four treatments, including no film control (CK), reinforced polyethylene film (RF), biodegradable film PBAT + starch (BDF1), and biodegradable film PBAT + PLA (BDF2). Soil physiochemical properties, temperature and humidity dynamics, microbial community structure, and film degradation status were investigated. The results showed that the RF treatment improved available P and K contents, while the BDF2 treatment significantly increased soil organic matter, NH4⁺-N, water-soluble Ca^2+, and Mg²⁺ contents. The soil temperature followed the order of RF > BDF1 > BDF2 > CK, and the humidity was BDF1 > RF > CK > BDF2, with RF treatment showing a more stable soil temperature, while BDF2 treatment fluctuated the most. There were no significant differences in bacterial diversity among the treatments, while the highest fungal diversity was observed in the BDF2. Water-soluble Mg was the key factor driving the changes in microbial community structure (p < 0.05). The film degradation rate followed BDF2 > BDF1 > RF. Collectively, RF is suitable for targeting short-term yield improvement, while BDF2 has significant advantages in sustainable cultivation in the long-term. Full article

This study examines the application of mining effluents as feed solutions in a bench scale pressure retarded osmosis (PRO) system for energy generation and the prospect of water recycling or safe discharge to the environment. Effluents were characterized and pretreated by ultrafiltration (UF) and nanofiltration (NF) prior to PRO. The PRO process was then conducted over 6 h in a cross flow flat plate cell with an effective membrane area of 34 cm², a hydraulic pressure of 12.4 bar and a 3M ammonium carbonate (NH₄)₂CO₃ as draw solution. Effluent 1 contained ions such as Cl⁻ (539 mg/L), NO₃⁻ (585 mg/L), SO₄²⁻ (3000 mg/L), Na⁺ (560 mg/L), and Mg²⁺ (656 mg/L), with a total dissolved solids (TDS) concentration of 5400 mg/L, chemical oxygen demand (COD) of 136 mg/L, total organic carbon (TOC) concentration of 3.5 mg/L, and acidic pH of 3.8, while effluent 2 was highly dominated by Cl⁻ (32,100 mg/L), NO₃⁻ (9720 mg/L), SO₄²⁻ (6512 mg/L), Na⁺ (14,306 mg/L), and Mg²⁺ (5336 mg/L), had a TDS concentration of 73,315 mg/L, COD of 8100 mg/L, TOC concentration of 10.2 mg/L, and pH of 7.4. These physiochemical properties indicated a significant potential of fouling and scaling which necessitated the appropriate pretreatments. It was shown that integrating UF and NF pretreatments was highly effective in refining the quality of effluents with a significant removal efficiency of above 90% for ions and heavy metals by NF, led to fouling mitigation, higher and more stable power density as well as potential water reuse or safe environmental discharge. The achieved water fluxes and power densities were 54 L/m²h and 18.6 W/m², for effluent 1, and 38 L/m²h and 13 W/m², for effluent 2, respectively. The outcome of this study is applicable for the mining sector especially in remote areas with the potential for water and energy recoveries to contribute to more sustainable mining operations. Full article

The development of new anti-inflammatory agents with improved safety and efficacy remains a major therapeutic challenge, particularly in light of the adverse effects associated with conventional nonsteroidal anti-inflammatory drugs. In this study, a series of new flavone derivatives were synthesized and evaluated for their inhibitory activities against Cyclooxygenase-1 (COX-1), Cyclooxygenase-2 (COX-2), and 5-Lipooxygenase (5-LOX) through combined in vitro and in silico approaches. Biological screening demonstrated that several derivatives exhibited moderate to strong inhibitory activity across the three enzymes, with IC₅₀ values ranging from 35.67 ± 2.92 to 1137.44 ± 371.05µM. Among these, compounds 5a and 5b emerged as the most promising dual COX-2/5-LOX inhibitors, displaying potent activity toward both targets while maintaining limited COX-1 inhibition, as reflected by their favorable selectivity indices (SI = 2.09 and 5.21, respectively). Molecular docking studies supported the experimental findings, revealing favorable binding affinities of compounds 5a and 5b within the COX-2 active site (PDB: 1CX2), while the flavone–tetrazole hybrid 6b exhibited the highest binding affinity toward the 5-LOX active site (PDB: 6N2W), consistent with its notable inhibitory activity. In silico ADME and toxicity predictions further suggested that the selected derivatives (4a-b, 5a-b, and 6a-b) possess acceptable physiochemical properties, low predicted toxicity, and favorable drug-likeness. Overall, this study identifies flavone-based scaffolds as a promising early-stage lead for the development of dual COX-2/5-LOX inhibitors and provides a rational basis for the design of safer anti-inflammatory agents. Full article

Soil salinization is a major environmental hazard, hindering rapeseed development due to sodium ion (Na⁺) toxicity and ionic imbalances in plant cells. Understanding tolerance mechanisms and categorizing reliable physiochemical indicators is vital for enhancing rapeseed tolerance. Herein, we aimed to enhance knowledge about the stress-responsive mechanism of ten rapeseed varieties (C71, C88, C91, C97, C123, C136, C196, C272, C280, and C320) exposed to five NaCl concentrations (0, 150, 200, 250, and 300 mM) through determining key factors related to salt tolerance at the seedling stage. Our results showed that salt stress significantly reduced seedling growth and biomass with increasing salt stress concentration in a similar pattern in all studied varieties, especially in sensitive seedlings. Furthermore, photosynthetic pigment, osmotic solutes, and MDA showed significant variations under salt treatment versus control in all studied varieties. Based on morpho-physiochemical trait analysis of ten rapeseed varieties, C71 and C272 were selected as tolerant and sensitive varieties to study stress responses during six weeks (weekly time points) in the leaf, petiole, stem, and root of seedlings under 250 mM NaCl. Current findings demonstrated superior osmotic adjustment of C71 through higher accumulation of total soluble sugars and protein, reflected in lower MDA levels, which contributed to maintaining cellular homeostasis and membrane integrity to improve resilience under salinity versus C272. Besides, total amino acid content was enhanced in C71 versus C272 seedlings, which was attributed to stress tolerance. In different tissues of C71 and C272, Na⁺ and K⁺ levels varied with increasing growing time, reaching the maximum increment at the 6th week under salt stress conditions. Moreover, Na⁺ initially accumulates in roots and enhances the K⁺ level in tolerant seedlings; besides, K⁺ was accumulated higher in the roots of tolerant seedlings, resulting in K⁺ homeostasis, thereby improving stress tolerance. Our results can be a great reference value for rapeseed plant breeders to develop salt-tolerant cultivars. Full article

This study aimed to develop dissolving microneedles (MNs) for the buccal delivery of cannabidiol (CBD). CBD is a non-psychotomimetic phytocannabinoid with anti-inflammatory and anxiolytic properties. The MN arrays were produced using micromolding, which has the ability of scalability. However, this approach lacks the ability to customize needle geometry; thus, additive manufacturing was implemented in the study. Digital Light Processing (DLP) printing is a promising way to produce molds with customized MN architecture. In the present study, molds were fabricated from 3D-printed MN arrays to prepare dissolving MNs for buccal administration. Polymeric needles based on Eudragit L100-55 and Eudragit RSPO were produced from reverse molds and they were evaluated regarding their physiochemical and mechanical properties, followed by in vitro and ex vivo studies using porcine buccal mucosa. Visualization studies were conducted using confocal scanning laser microscopy, whereas the membrane integrity of the porcine mucosa upon application of the MNs was assessed by histological evaluation. Our results suggest that the needles can be effectively inserted into the buccal tissue and release the active pharmaceutical ingredient (API) in a controlled manner. This approach offers a patient-friendly alternative to oral CBD delivery, bypassing first-pass metabolism. Full article

Glioblastoma (GBM) is the most common malignant primary brain tumor among adults and one of the deadliest human cancers. Its infiltrative growth pattern, high intratumor heterogeneity, and the existence of the blood–brain barrier severely limits current treatment approaches. Precision medicine-guided treatment decision-making based on unique molecular characteristics of patients’ tumors and tumor microenvironments is highly desired. Gold nanoparticles (AuNPs) are promising nanoplatforms that enable precision medicine and personalized treatments for GBM. Their size- and shape-dependent tunable physiochemical properties, ease of surface functionalization, unique optical/electronic properties, and biocompatibility have facilitated the development of AuNP-based multimodal agents with the capability of delivering therapies, molecular imaging, and diagnosis in one platform. Recent research has shown that AuNPs can deliver chemotherapeutics, genes, and immunotherapeutics and aid in imaging, radiosensitization, and photothermal therapy for GBM therapy. Ligand-targeted and stimuli-responsive AuNPs enable site-selective targeting of GBM cells and the tumor microenvironment, allowing for personalized medicine approaches. Here, we review the progress made in biomedical applications of AuNPs for GBM treatment with a focus on precision-based drug/gene delivery, diagnosis/imaging, and therapy enhancement. We also discuss safety, biodistribution, scalability for translation, and regulatory challenges that need to be addressed for AuNP development. Future opportunities for AuNPs in personalizing GBM treatment are also highlighted. Full article

Oral administration of tocotrienol has poor systemic distribution due to poor selectivity by the α-tocopherol transfer protein at the liver. Local injection of tocotrienols with appropriate drug delivery systems is significant to ensure that the drug is delivered directly to the site of injury or fracture. This paper presents a tocotrienol-loaded gelatin hydrogel crosslinked with genipin for bone regeneration. This innovative method improves the incorporation and sustained delivery of tocotrienol while overcoming its incompatibility with hydrophilic biomaterials. It establishes a novel platform for targeted therapeutic applications in bone treatment. The cytotoxicity and physicochemical properties of tocotrienol were examined using the genipin-crosslinked gelatin hydrogel. A 10% tocotrienol nanoemulsion (TTE) was prepared using a sonicator and characterized with a zeta sizer and FTIR. A dose–response analysis was conducted to determine the appropriate tocotrienol concentration for hydrogel integration with gelatin (7% or 10% w/v) and crosslinked with genipin (0.1% or 0.3% w/v). The dose–response study’s tocotrienol nanoemulsion was added to gelatin before polymerization. With 141.9 nm particles and 0.150 PDI, the nanoemulsion was homogeneous and stable. The 1% tocotrienol nanoemulsion was chosen due to its viability. Formulations 1% TTE_0.1% GNP_7% GEL and 1%TTE_0.3% GNP_7% GEL had superior physicochemical properties compared to other groups. The 1% TTE_0.3% GNP_7% GEL had outstanding hydrophilicity, low weight loss, and a suitable swelling ratio for bone application. SEM scans of the surface and cross-section showed that 1% TTE_0. 3% GNP_7% GEL had interconnected pores with an optimal average pore size of 292 ± 37 μm. Adding tocotrienol to the gelatin hydrogel matrix did not affect FTIR, XRD, or EDX. In vitro cytotoxicity studies indicated >90% cell viability of hFOB 1.19 cells cultured on 1% TTE_0.1% GNP_7% GEL and 1% TTE_0.3% GNP_7% GEL (105 ± 4.36% and 95.36 ± 9.78%). Combining tocotrienol with a genipin-crosslinked gelatin hydrogel demonstrated superior physicochemical properties and no in vitro toxicity. Full article

Efficient resource allocation during fruit expansion and ripening is critical for enhancing mango (Mangifera indica L.) productivity and fruit quality. A study was conducted to quantify the effects of foliar-applied GA₃ at concentrations of 0 (control), 50 (GA50), 100 (GA100) and 200 (GA200) mg L⁻¹, applied at 15, 25 and 35 days after full bloom, on fruit physiochemical attributes during the fruit expansion and ripening phases. In addition, metabolic profiling and pathway analysis were conducted after fruit ripening. Compared with the control, GA₃ application at 50, 100, and 200 mg L⁻¹ increased fruit length by 8, 12, and 14%, and fruit diameter by 5, 11, and 14%, respectively. The mean single-fruit weight was increased by 5–11% at physiological maturity. During the fruit expansion phase, GA₃ treatment decreased starch and total acidity by up to 11% and 29%, respectively, while increasing the soluble sugar content by 21%. Furthermore, enhanced antioxidant enzyme activities (SOD, POD, and CAT), accompanied by a reduction in malondialdehyde (MDA) contents in leaves, were observed. At the ripening stage, GA₃-treated fruits exhibited lower weight loss, higher firmness, more uniform color development, and reduced disease incidence, although vitamin C content and total soluble solids declined. PCA analysis identified GA100 as the optimal treatment. Metabolomics analysis revealed 287 differentially regulated metabolites between GA100 and the control. Sweet, fruity, and floral compounds were upregulated, whereas terpenoids and aldehydes were downregulated. KEGG pathway analysis indicated that GA100 modulated key resource-related metabolic pathways, including nitrogen, carbon and energy metabolism, thereby promoting efficient resource allocation toward fruit growth, quality, and aroma development. Overall, preharvest foliar application of GA₃, particularly at a concentration of 100 mg L⁻¹ (GA100), markedly improved mango fruit growth and quality but tended to simplify the aroma profiles by favoring ester production over complex terpenoid-derived notes. Full article

The development of effective inhalable drugs remains a key challenge in the treatment of pulmonary diseases, due to the physiological barriers of the respiratory tract and the lack of predictive models that accurately reproduce the human lung environment. In this context, liposomes (LP) have emerged as promising nanocarriers for pulmonary drug delivery due to their high biocompatibility, surfactant-like composition, capacity to encapsulate both hydrophilic and lipophilic drugs, and potential to provide sustained drug release while reducing systemic toxicity. This study evaluates the influence of size and PEGylation on their physicochemical properties, cytotoxicity, interaction with the pulmonary mucus, and cellular internalisation. LP of 100 nm (LP 100), 200 nm (LP 200), and 600 nm (LP 600) were characterised physiochemically and evaluated in pulmonary cell lines (A549 and Calu-3) exposed in liquid–liquid interface (LLI) and air–liquid interface (ALI) by nebulisation. In addition, artificial pulmonary mucus (APM) was employed to analyse LP penetration through the pulmonary mucus barrier. Results indicate that LP 100 exhibits greater colloidal stability, lower cytotoxicity, and sustained migration through the APM over time with respect to larger particles. PEGylation of LP 100 (LP-PEG) further increases their stability and ability to penetrate the APM, although cellular internalisation is reduced due to the steric effect of the PEG coating. These findings highlight the importance of adjusting the size and surface modifications of LPs according to the therapeutic target of the drug, optimising their persistence on the epithelial surface or their cellular uptake. Full article

Extracellular vesicles (EVs) of human origin show promise for regenerative medicine and wound healing. However, they have limitations regarding scalability, variability, safety, and costs. Plant-derived EVs may represent a valid alternative. This study investigated the regenerative potential of EVs extracted from orange juice (oEVs). oEVs obtained by standard ultracentrifugation were compared with oEVs purified by tangential flow filtration (TFF), a scalable technique suitable for large-scale and regulatory-compliant manufacturing. Comparisons included size, morphology, pH, Zeta potential, protein and RNA content, Raman spectroscopy, and proteomic, metabolomic, and RNA sequencing. The regenerative potential of oEVs was tested in vitro, with cell migration, endothelial tube formation, and proliferation assays performed. Antioxidant ability was tested on endothelial cells stressed by hyperglycemia or pro-inflammatory cytokine cocktails. Next, oEVs were formulated with different hydrogels and tested at different doses on skin ulcers on healthy and diabetic mice. TFF oEVs showed the same physio-chemical characteristics and a comparable molecular content as those isolated by ultracentrifugation, confirming the path to scalability. In vitro oEVs promoted cell migration, formation of capillary-like structures, cell proliferation, and strong antioxidant activity. Moreover, oEVs effectively accelerated in vivo wound closure in healthy and diabetic mice. Thus, oEVs may provide a useful and cost-effective ingredient for improved and effective wound treatment strategies. Full article