Search Results (3,598)

This study presents the synthesis of manganese molybdenum tetraoxide (MnMoO₄)-based nanoparticles and then their experimental demonstration as saturable absorbers (SAs) in erbium-doped fiber lasers (EDFLs). The MnMoO₄ nanoparticles were prepared and then embedded between the fiber ferrule to act as an SA to generate Q-switched pulsed operation in EDFLs. For the characterization, scanning electron microscopy (SEM) was employed to confirm the particle size of the prepared MnMoO₄ nanoparticles, and the SA optical properties were further investigated by measuring their modulation depth and saturation intensity. By implementing the prepared SA within the cavity, the measured results revealed that under pump power ranging from 28 to 312.5 mW, the laser exhibited Q-switched pulse durations varying from 15.22 to 2.35 µs and repetition rates spanning from 24.98 to 88.11 kHz. The proposed EDFL system delivered an average output power between 0.128 and 2.95 mW, pulse energies ranging from 5.12 to 33.49 nJ, and peak power from 0.281 to 6.26 mW. The laser stability was also confirmed by continuously noticing the pulse duration, emission wavelengths, and pulse repetition rates for 4 h. Finally, a numerical model based on a nonlinear Schrödinger equation (NLSE) was employed to validate both experimental and theoretical results of the passive Q-switched EDFL. These findings highlight the potential of EDFLs utilizing MnMoO₄-based SAs for potential applications in pulsed laser sources. Full article

In this study, we have demonstrated an ultrafast Tm-doped fiber laser utilizing the nonlinear multimode interference (NL-MMI) effect, with a single mode fiber–grade index multimode fiber–single mode fiber (SMF-GIMF-SMF) structure serving as the saturable absorber (SA). In addition to stable pulses, mode-locked pulses with chaotic features can be obtained in this fiber laser, characterized by a high average output power and pulse energy, resembling noise-like pulses. By employing the time-stretch dispersive Fourier transform (TS-DFT) technology, it can be seen that the sub-pulses constituting these pulses exhibit noisy characteristics with random intensities and energies. Furthermore, the numerical simulations elucidate the corresponding generation mechanism and dynamic evolution. These findings significantly enhance the comprehension of pulse dynamics and offer novel insights into the technological development and application prospects of ultrafast fiber lasers. Full article

Fault diagnosis based on the partial discharge (PD) recognition has been widely applied on a gas-insulated line breaker (GILB) and gas-insulated switchgear (GIS) as a reliable online condition monitoring method. This paper dealt with insulation defect diagnosis based on a Random Forest (RF) algorithm with an optimized feature selection method. Four different types of insulation defect models, such as the free-moving particle (FMP) defect, the protrusion-on-conductor (POC) defect, the protrusion-on-enclosure (POE) defect, and the delamination defect, were prepared to simulate representative PD single pulses and PRPD patterns generated from the GILB. The PD signals generated from defect models were detected using the PRPD sensor which can detect phase-synchronized PD signals with the applied high-voltage (HV) signals without the need for additional equipment. Various statistical PD features were extracted from PD single pulses and PRPD patterns according to four kinds of PD defect models, and optimized features were selected with respect to variance importance analysis. Two kinds of PD datasets were established using all statistical features and top-ranked features. From the experimental results, the RF algorithm achieved accuracy rates exceeding 92%, and the PD datasets using only half of the statistical PD features could reduce the computational times while maintaining the accuracy rates. Full article

In power systems, MOSFET devices used in industrial chips exhibit more pronounced degradation when subjected to intense electromagnetic pulses than in conventional environments. Conventional reliability testing methods, which fail to simulate dynamic electromagnetic environments, are unable to accurately assess the changes in device performance under electromagnetic interference. In this study, we employed a transmission line pulse generator to apply pulse stress to N-type MOSFET devices, systematically investigating the degradation mechanisms by varying pulse features such as pulse cycle, amplitude, rise/fall times, and intervals. The results indicate that changes in the electrical properties of the devices are primarily influenced by two types of charged traps. Under the conditions of low pulse cycles, the current response of the devices may even exceed that prior to stress application. The study further analyzed the competitive mechanisms of these different traps during the device degradation process. Additionally, by varying the test temperature to mimic industrial application scenarios, we analyzed the degradation behavior of the devices under multi-physics conditions. Full article

The optimization of photoinjector brightness is crucial for achieving the highest performance at X-ray free-electron lasers. To this end, photocathode laser pulse shaping has been identified as a key technology for enhancing photon flux and lasing efficiency at short wavelengths. Supported by beam dynamics simulations, we identify transversely and longitudinally truncated Gaussian electron bunches as a beneficial bunch shape in terms of the projected emittance and 5D brightness. The realization of such pulses from chirped Gaussian pulses is studied for 514 nm and 257 nm wavelengths by inserting an amplitude mask in the symmetry plane of the pulse stretcher to achieve longitudinal shaping and an aperture for transverse beam shaping. Using this scheme, transversely and longitudinally truncated Gaussian pulses can be generated and later used for the production of up to 3 nC electron bunches in the photoinjector. The 3D pulse shape at a wavelength of 514 nm is characterized via imaging spectroscopy, and second-harmonic generation frequency-resolved optical gating (SHG FROG) measurements are also performed to analyze the shaping scheme’s efficacy. Furthermore, this pulse-shaping scheme is transferred to a UV stretcher, allowing for direct application of the shaped pulses to cesium telluride photocathodes. Full article

Active magnetic bearings (AMBs), pivotal in high-speed rotating machinery for their frictionless operation and precise control, demand power amplifiers with exceptional dynamic performance and minimal current ripple. However, conventional amplifier designs often overlook eddy current effects, a critical oversight given the high-frequency switching inherent to pulse-width modulation (PWM). These induced eddy currents distort output waveforms, amplify ripple, and degrade system bandwidth. This paper bridges this critical gap by proposing a comprehensive methodology to model, quantify, and mitigate eddy current impacts on three-level half-bridge power amplifiers. A novel mutual inductance-embedded circuit model was developed, integrating winding–eddy current interactions under PWM operations, while a discretized transfer function framework dissects frequency-dependent ripple amplification and phase hysteresis. A voltage selection criterion was analytically derived to suppress nonlinear distortions, ensuring stable operation in high-precision applications. A Simulink simulation model was established to verify the accuracy of the theoretical model. Experimental validation demonstrated a 212% surge in steady-state ripple (48 mA to 150 mA at 4 A DC bias) under a 20 kHz PWM operation, aligning with theoretical predictions. Dynamic load tests (400 Hz) showed a 6.28% current amplitude reduction at 80 V DC bus voltage compared to 40 V, highlighting bandwidth degradation. This research provides a paradigm for optimizing AMB power electronics, enhancing precision in next-generation high-speed systems. Full article

A passively Q-switched Thulium-doped fiber laser based on glycerin as the saturable absorber is experimentally demonstrated for the first time. The saturable absorber consists of two FC/PC connectors aligned within a mechanical fiber-fiber coupler, with the intervening gap filled with glycerin. Such a saturable absorber is integrated into a compact ring cavity, enabling passive Q-switched laser operation. Starting at a minimum pump power of 1.7 W, Q-switched pulses with a central wavelength of 1946 nm are obtained. At the maximum pump power of 2.4 W, the laser generates pulses with a duration of approximately 2 µs, a repetition rate of 26.7 kHz, and a pulse energy of 1.08 µJ. To the best of our knowledge, this is the first demonstration of passively Q-switched laser operation utilizing a glycerin-based saturable absorber for generating pulsed emission at the 2-µm wavelength region. This breakthrough represents a significant advancement in fiber laser technology, introducing a novel and efficient approach to pulse generation. Full article

This paper reports a comparative study on the high temperature pyrolysis characteristics of three C₉H₁₂ isomers, including n-propylbenzene (PBZ), 1,3,5-trimethylbenzene (T135MBZ), and 1,2,4-trimethylbenzene (T124MBZ), via single-pulse shock tube (SPST) experiments and kinetic simulations. The SPST experiments were conducted in the temperature range of 1100–1700 K, at pressures of 10 bar and 15 bar, with a fixed fuel concentration of 200 ppm. The reaction time was approximately 1.8 ms for all of the experiments. The distributions of the pyrolysis products were quantitatively analyzed as functions of pressure and temperature. A detailed kinetic mechanism was used to simulate the experimental results, and it is demonstrated that the mechanism can capture the pyrolysis characteristics reasonably well. Both experimental and simulation results reveal that PBZ exhibits higher fuel reactivity than T124MBZ and T135MBZ under the studied conditions. Pyrolysis of all three C₉H₁₂ isomers generates key soot precursors, including acetylene and benzene. Sensitivity and rate-of-production (ROP) analyses indicate similar primary pyrolysis pathways. The benzyl radical is first formed through the dehydrogenation reaction and then it undergoes a series of decomposition reactions leading to the detected small hydrocarbon species. This study not only provides an in-depth understanding of the high temperature pyrolysis characteristics of the three C₉H₁₂ isomers, but also provides essential validation data for the development and optimization of chemical kinetic mechanisms for alkyl aromatic hydrocarbons. Full article

High-test peroxide (HTP) monopropellant thrusters are being considered for spacecraft lander missions due to their simplicity and reduced toxicity compared to traditional propellants. Pulse-Width Modulation (PWM) throttling is a key technique for precise thrust control in such systems. However, PWM throttling can lead to pressure surges and oscillations in the propellant feed system, potentially compromising system reliability. This study investigates the influence of PWM parameters, specifically duty cycle and frequency, on pressure surges and oscillations in a 50-newton-class HTP monopropellant thruster. The objective is to identify stable operating conditions that mitigate these effects, thereby enhancing the reliability of PWM throttling for lander applications. An experimental setup was developed, including a 50-newton-class thruster with a ${\mathrm{MnO}}_2{\mathrm{/La/Al}}_2{\mathrm{O}}_3$ catalyst and a solenoid valve for PWM control. Cold flow tests using water characterized the valve response and water hammer effects, while hot fire tests with 90 wt.% HTP were used to evaluate thruster performance under steady-state and PWM conditions. Analytical methods, including Joukowsky’s equation and power spectral density analysis, were used to interpret the data and understand the underlying mechanisms. The results showed that while surge pressures generally aligned with steady-state values, specific PWM conditions led to amplified surges, particularly at low duty cycles. Additionally, high duty cycles induced chugging instability. The natural frequencies of the feed system were found to play a crucial role in these phenomena. Stable operating conditions were identified by avoiding duty cycles that cause constructive interference of pressure waves. This research demonstrates that by carefully selecting PWM parameters based on the feed system’s dynamic characteristics, pressure surges and oscillations can be minimized, ensuring reliable operation of HTP monopropellant thrusters in PWM throttling mode. These findings contribute to the development of more efficient and safer propulsion systems for spacecraft landers. Full article

The Shuixie Cu–Co polymetallic orefield, located in western Yunnan Province (southeastern margin of the Qinghai–Tibet Plateau), is renowned for its Cu–Co mineralization. A recent resource reassessment identified Sb–Au and Cu–Co–Bi (Sb–Au) orebodies as genetically associated with primary Cu–Co mineralization. The mineralization characteristics and microscopic observations indicate that gold mineralization in the Sb–Au orebodies follow a pulsating fluid injection model. The model includes four pulses: (1) euhedral gold-poor pyrite (PyI₁) precipitation; (2) margin-parallel growth of gold-rich pyrite (PyI₂) on PyI₁; (3) continued growth of gold-rich pyrite (PyI₃) along PyI₂; and (4) outermost concentric gold-rich pyrite (PyI₄) formation. This study examined gold-bearing pyrite in orebodies and host rocks. In situ laser ablation inductively coupled plasma mass spectrometry (LA–ICP–MS) analysis of pyrite and inductively coupled plasma mass spectrometry (ICP–MS) whole-rock trace element analysis were conducted to track the ore-forming fluid evolution. Compared with CI chondrite, pyrites from all pulses were enriched in LREEs over HREEs. The pyrite REE distribution curves exhibited right-skewed patterns, reflecting LREE enrichment. The Hf/Sm, Nb/La, and Th/La ratios were generally below 1, indicating high-field-strength element depletion. These results suggest a Cl-rich, F-poor ore-forming fluid. The pyrite trace elements showed enrichment in the chalcophile elements (e.g., Cu and Pb) and exceptionally high Bi levels compared with the continental crust. The chalcophile elements (e.g., Zn and Cd) were depleted, whereas iron-group elements (e.g., Co) were enriched and Ni was depleted. The pyrite δCe values (0.87–1.28, mean = 1.01) showed weak anomalies, indicating a reducing ore-forming environment. The δEu values of pyrite during pulses 1 to 4 ranged widely, from 0.2–3.01 (mean of 1.17), 0.27–1.39 (0.6), and 0.41–1.40 (0.96) to 0.4–1.36 (0.84), respectively, suggesting an initial temperature decline and subsequent increase in the ore-forming fluid. Significant variations were found in the Y/Ho, Zr/Hf, and Nb/Ta ratios across pulses, indicating the potential involvement of high-temperature hydrothermal fluids or late-stage alteration during ore formation. The Y/Ho ratio of pyrite overlapped most closely with that of the continental crust of China, indicating a close relationship between the ore-forming fluids and the crust. Full article

Event data loggers are frequently used to record the date and time of tip events in tipping-bucket rain gauges. The HOBO^® pendant event data logger is one such commercially available device commonly used for this purpose. It can record the contact closure of a TBGR reed switch at a maximum timing resolution of 1 s, tied to the timing of the logger clock, which is set each time the logger is launched. These event loggers are ideal for the routine recording of rainfall. This paper addresses the issue of whether they can also be relied upon when estimating short-term intensities, for which they were not designed. New experiments show that for a series of switch closures at fixed intervals other than exact multiples of 1 s, the HOBO^® logger fails to record evenly spaced tip events. Thus, for example, with pulses at fixed 2.75 s intervals, the logger records some events as occurring at 2 s intervals and others at 3 s intervals. This quantization error means that there can be large errors in the logged time between bucket tip events. In natural rainfall, tip events can occur at any time, and inter-tip times, from which intensity can be estimated, will generally not be an integral number of seconds. Consequently, particularly in intense rain, the logger behaviour just described can lead to erroneous estimates of the rainfall rate estimated from the duration of individual inter-tip times. Possible solutions are discussed. Full article

We conducted a comprehensive comparative study of numerical solvers for the generalized Korteweg–de Vries (gKdV) equation, focusing on classical Fourier-based Crank–Nicolson methods and physics-informed neural networks (PINNs). Our work benchmarks these approaches across nonlinear regimes—including the cubic case ($\nu =3$)—and diverse initial conditions such as solitons, smooth pulses, discontinuities, and noisy profiles. In addition to pure PINN and spectral models, we propose a novel hybrid PINN–spectral method incorporating a regularization term based on Fourier reference solutions, leading to improved accuracy and stability. Numerical experiments show that while spectral methods achieve superior efficiency in structured domains, PINNs provide flexible, mesh-free alternatives for data-driven and irregular setups. The hybrid model achieves lower relative $L^2$ error and better captures soliton interactions. Our results demonstrate the complementary strengths of spectral and machine learning methods for nonlinear dispersive PDEs. Full article

In the rapidly advancing era of intelligent technology, flexible strain sensors are emerging as a key component in wearable electronics. Laser-induced graphene (LIG) stands out as a promising fabrication method due to its rapid processing, environmental sustainability, low cost, and superior physicochemical properties. However, the stretchability and conformability of LIG are often limited by the substrate material, hindering its application in scenarios requiring high deformation. To address this issue, we propose a high-performance flexible and stretchable strain sensor fabricated by generating graphene on a polyimide (PI) substrate using laser induction and subsequently transferred onto a polydimethylsiloxane (PDMS). The resultant sensor demonstrates an ultra-low detection limit (0.1%), a rapid response time (150 ms), a wide strain range (40%), and retains stable performance after 1000 stretching cycles. Notably, this sensor has been successfully applied to the real-time monitoring of civil aviation test pilots during flight for the first time, enabling the accurate detection of physiological signals such as pulse, hand movements, and blink frequency. This study introduces a unique and innovative solution for the real-time health monitoring of civil aviation test pilots, with significant implications for enhancing flight safety. Full article

Previous studies have demonstrated that underwater low-temperature plasma is effective for synthesizing nanomaterials by generating plasma discharges between metal electrodes submerged in water. This study extends this approach to the one-step synthesis of MXenes containing titanium, molybdenum, and titanium–molybdenum composites through pulsed discharges in carbon tetrachloride, an oxygen-free, non-flammable solvent characterized by a high boiling point and low permittivity. By employing titanium and molybdenum electrodes in various configurations, three MXene samples were synthesized: Ti₂CT_X, Mo₂CT_X, and Mo₂TiC₂T_X. Characterization techniques, including UV-Vis spectroscopy, X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy, confirmed the successful synthesis of high-purity MXenes with distinct structural and optical properties. Notably, the bandgap values of the synthesized MXenes were determined as 1.71 eV for Ti₂CT_X, 1.42 eV for Mo₂TiC₂T_X, and 1.07 eV for Mo₂CT_X. The photocatalytic performance of the synthesized MXenes was evaluated, showing a removal efficiency of 65% to 98% for dye mixtures, with methylene blue showing the highest degradation rate. This plasma-assisted method offers a scalable, precursor-free route for the synthesis of MXenes with potential applications in energy storage, environmental remediation, and optoelectronics due to their tunable bandgaps and high catalytic activity. Full article

Under the framework of classical electrodynamics, this article investigates the nonlinear Thomson scattering generated by the cross-collision between a tightly focused linearly polarized Gaussian laser pulse and a relativistic electron through numerical simulation and emulation. The oscillation direction and emission angle of the electron’s trajectory are influenced by the beam waist radius and the delay time. The spatial radiation distribution of electrons exhibits a comet-shaped pattern, with the radiation being concentrated in the forward position. This is attributed to the high laser intensity at the focus, resulting in intense electron motion. As the beam waist radius keeps increasing continuously, the maximum radiation polar angle in the spatial distribution decreases. The time spectrum exhibits a symmetrical three-peak structure, with a high secondary peak. Meanwhile, the supercontinuum spectrum gradually transforms into a multi-peak distribution spectrum. In the multi-peak mode, the main peak and the secondary peak will interchange during the increase in the waist radius, generating rays with higher frequencies and energies. The aforementioned research findings reveal a portion of the mechanism of the nonlinear Thomson scattering theory and are beneficial for generating X-rays of higher quality. Full article