Search Results (285)

Cationic surfactants from quaternary ammonium compounds (QACs) are increasingly recognized as relevant micropollutants particularly following their widespread use during and after the COVID-19 pandemic. The new EU Urban Wastewater Treatment Directive (2024/3019) highlights micropollutant removal as a regulatory priority, mandating advanced treatment for their elimination. In this context, this study examined benzalkonium chloride (BAC) retention and membrane response during nanofiltration (NF) and reverse osmosis (RO), across concentrations ranging from monomeric to micellar. RO membranes achieved >97% rejection, whereas NF showed 65–96% removal strongly affected by micelle formation. Flux decline was most pronounced in RO, with relative permeability (J/J₀) decreasing to ~0.12 at 1.0 CMC, while NF membranes exhibited better hydraulic stability. Membrane active layer zeta potential measurements confirmed adsorption and charge neutralization, with shifts toward less negative values after BAC exposure. Hermia model analysis revealed that fouling was governed by cake layer formation or pore blocking, depending on membrane type and feed concentration. Full article

This study investigates strategies to reduce mould growth on steamed beech wood by evaluating drying-based and fungicide-based protection approaches. The drying-based approach focused on optimising the temperature of warm-air drying parameters to control moisture content and limit mould development. The fungicide-based approach involved testing selected agents, including 3-iodo-2-propynyl butyl carbamate, boric acid, quaternary ammonium compounds, and nano-ZnO, for their effectiveness in preventing mould formation. Mould growth was assessed by macroscopic observation and classified according to standardised intensity levels. The results indicate that adjusting drying parameters alone is insufficient to prevent mould growth, whereas specific fungicide treatments provide effective surface protection. These findings offer practical guidance for minimising mould development on beech wood during drying and storage. Full article

Organic redox-active molecules are promising catholyte materials for aqueous organic redox flow batteries (AORFBs), yet they often suffer from low solubility and poor cycling stability. Herein, we report a series of water-soluble phenothiazine derivatives functionalized with quaternary ammonium groups. The optimized compound, N,N,N-trimethyl-1-(10H-phenothiazin-10-yl) propan-2-aminium chloride (TMiPrPTCl), exhibits exceptional solubility (2.69 M in water) and a high redox potential (0.902 V vs. SHE). A comparative study of four derivatives reveals that side-chain length and branching critically modulate both solubility and degradation pathways: while three-carbon-linked analogs N,N,N-trimethyl-3-(10H-phenothiazin-10-yl)propan-1-aminium chloride (TMPrPTCl) degrade primarily via irreversible oxidation to sulfoxide, two-carbon-linked species (TMiPrPTCl) undergo additional side-chain cleavage, leading to rapid capacity fade. Although the quaternization strategy successfully achieves record solubility, the electrochemical stability remains a key challenge. Post-cycling analysis confirms the loss of redox activity and the formation of inert products. This work highlights the delicate balance between solubility enhancement and molecular stability, providing clear design guidelines for future phenothiazine-based catholytes. Full article

Salmonella enterica remains a major food safety concern in poultry, and processing-related stress can influence its survival and persistence. This study evaluated the phenotypic expression of S. enterica serotypes Kentucky (SK), Infantis (SI), Schwarzengrund (SS), and Typhimurium (ST) following antimicrobial and temperature stressors. A pre-harvest isolate of each serotype was gradually exposed to increasing concentrations of peracetic acid (PAA) and quaternary ammonium compounds (QACs), starting at 40 ppm and 1 ppm, respectively, until minimum inhibitory and bactericidal concentrations (MICs/MBCs) were established. Stressed cells were then subjected to cold (4 °C, 60 min) and heat (55 °C, 6 min) shock and assessed for sanitizer tolerance, biofilm formation and recovery, and antibiotic resistance. Sanitizer tolerance after daily conditioning varied among S. enterica serotypes, with ST and SK showing the highest tolerance to PAA and QACs, respectively. The tolerance of PAA variants increased by 10–20 ppm and QAC variants by 2–8 ppm following stress exposure. The double-stressed variants of ST significantly (p < 0.05) formed more biofilm than the control after PAA, whereas no significant differences were observed among the variants for other serotypes. Biofilm recovery was higher for the stressed variants of SI and SS (p < 0.05) following PAA stress but remained the same across all serotypes after QAC stress. QAC-stressed variants showed more phenotypic changes across the antibiotics tested. Notably, the stressed variants of SK, SS, and ST displayed increased MICs, including a 2- to 4-fold rise in azithromycin for the SK and ST variants. There was an increase in the MICs of ceftriaxone and nalidixic acid for some SK and SS variants. These findings suggest that environmental stress can significantly enhance the tolerance, survival, and persistence of S. enterica. Full article

Quaternary ammonium compounds (QACs) have dominated biocidal practice in cultural heritage conservation for decades, yet growing evidence of environmental persistence, aquatic ecotoxicity, and antimicrobial resistance induction has prompted the search for safer alternatives. Essential oils (EO) have emerged as promising bio-based biocides, though their environmental performance has rarely been quantified through rigorous life cycle approaches. This study presents a comparative Life Cycle Impact Assessment (LCIA) of EO-based and QAC-based biocidal formulations across representative conservation scenarios, following ISO 14040/14044 standards and the Environmental Footprint 3.1 methodology with USEtox^® 2.1 characterization factors. Three complementary functional units were employed: formulation-based, surface-based, and intervention-based. The results reveal a fundamental trade-off: EO-based systems exhibit 81% higher climate change impacts but 82–89% lower human toxicity and freshwater ecotoxicity impacts compared to QAC-based systems. Surface-normalized comparisons reduce the climate gap to 32%, while toxicity advantages remain robust across all sensitivity scenarios. Monte Carlo analysis confirms the robustness of toxicity findings (p > 99%), whereas climate comparisons remain scenario-dependent. These findings support context-dependent adoption of EO-based biocides in conservation practice and demonstrate that EO-related climate impacts are technically mitigable, while QAC toxicity is intrinsic to their molecular structure. Full article

Candidozyma auris is an emerging multidrug-resistant yeast that readily contaminates healthcare environments, persisting on dry surfaces and enabling transmission and difficult-to-control outbreaks. A systematic review of environmental hygiene interventions targeting C. auris was conducted, focusing on efficacy against planktonic cells and surface-associated biofilms (including dry-surface biofilms, DSB where available). PubMed and Scopus were searched for English-language records published from 1 January 2017 to 30 September 2025, and study selection followed PRISMA 2020. Thirty-six studies from nine countries met the inclusion criteria. These were predominantly laboratory efficacy evaluations using carrier/suspension or quantitative surface methods reporting log₁₀ Colony Forming Unit (CFU) reductions; only seven studies assessed biofilm-associated C. auris. Across clades I–IV, chlorine-based disinfectants and oxidizing chemistries (hydrogen peroxide/peracetic acid formulations) most consistently achieved high-level reductions (often ≥ 5 log₁₀ CFU) under label-relevant conditions. In contrast, products containing only quaternary ammonium compounds (QACs) frequently underperformed and demonstrated greater variability. No-touch methods, particularly 254 nm ultraviolet-C light (UV-C), provided meaningful adjunctive reductions, but were highly dependent on dose delivery and geometry, and evidence for ozone-based approaches was mixed. Limited data on C. auris DSBs suggest planktonic testing may overestimate real-world conditions and underscore the importance of endpoints, such as transfer prevention and regrowth suppression. Full article

The research hypothesis was that adjusting the content of the quaternary ammonium urethane dimethacrylate monomer bearing an N-dodecyl substituent (QAUDMA-12) would yield dental matrices with high antimicrobial activity, good biocompatibility, and favorable physicochemical properties. The research hypothesis was verified for six Bis-GMA, TEGDMA, and UDMA copolymers containing from 2.5 to 40 wt.% QAUDMA-12 by determining their degree of conversion, hardness, flexural properties, water behavior, antimicrobial activity against Staphylococcus aureus, Staphylococcus epidermidis, Escherichia coli, Candida albicans, and cytotoxicity towards L929 mouse fibroblast cells. The research hypothesis was confirmed. Copolymers containing less than 30 wt.% QAUDMA-12 exhibited favorable polymerization efficiency, water sorption and solubility, and mechanical properties comparable to those of conventional Bis-GMA/TEGDMA systems. At the same time, they showed no cytotoxic effects toward mouse fibroblast cells. The results of antimicrobial tests show that the minimum QAUDMA-12 concentration providing sufficient antimicrobial activity was 20 wt.%. Therefore, it can be concluded that the 20 wt.% concentration of QAUDMA-12 makes it possible to obtain dental matrices that are non-toxic, exhibit antimicrobial activity, and possess the desired physico-mechanical performance. Full article

Listeria monocytogenes biofilms on surfaces that come into contact with food create ongoing challenges in produce-processing environments, highlighting the necessity for effective surface sanitation. This research examined the effectiveness of chlorine (200 ppm), quaternary ammonium compound (QAC, 400 ppm), and UV-C light (0.85 J/cm²) against L. monocytogenes biofilms developed on stainless steel, polyethylene terephthalate (PET), and silicone rubber materials frequently used in apple packing settings. Biofilms were cultivated using a mixture of LCDC and V7 strains in diluted apple juice and evaluated after 1 and 7 days of growth. The type of surface material and the age of the biofilm had a significant impact on the performance of the sanitizing agents (p < 0.05). Chlorine achieved a reduction of 2.84 ± 0.06 log CFU/coupon on 1-day-old biofilms on stainless steel, although its effectiveness dropped to 1.90 ± 0.07 log CFU/coupon on biofilms aged 7 days. Similar trends were noted for QAC (2.42 ± 0.05 to 1.73 ± 0.06 log CFU/coupon) and UV-C (2.71 ± 0.05 to 1.57 ± 0.08 log CFU/coupon) over time. PET and silicone rubber consistently exhibited lower log reductions than stainless steel for all treatments. The presence of organic matter from apple juice reduced the efficacy of sanitizers on all surfaces. These results emphasize the significant role of surface material, biofilm age, and organic load on sanitation effectiveness, offering practical recommendations for enhancing the control of L. monocytogenes in produce-processing facilities. Full article

Background: Effective cetylpyridinium chloride (CPC)-based mouthwashes critically depend on maintaining maximum levels of bioavailable CPC to deliver optimum antimicrobial benefits. While this is traditionally assessed using cellulose-based methods, from economic and efficiency perspectives, there remains a need to identify other potential methods of assessing bioavailable CPC. Here, we explored whether quaternary ammonium compound (QAC) test strips are sensitive to CPC-based formulations, and if so, whether there might exist a possible correlation with glycolysis outcomes. Methods: Quantitative color parameters were obtained using spectrophotometric assessments of QAC test strips immersed in simple CPC solutions and eight commercial CPC-based mouthwashes available in the USA. Then, using our established glycolysis model, we assessed the glycolytic response of both the simple CPC solutions and commercial CPC-based mouthwashes, and compared these data sets. Results: Significant differences (p < 0.05) among the CPC simple solutions were found. Importantly, spectrophotometric assessments and glycolysis trials produced good correlations. Evaluations of the commercial mouthwashes further underlined this correlation, even though those that comprise zinc salts may impact QAC-based color. Conclusions: Based on these results, we believe the use of QAC test strips provides an attractive option to formulators and brands specializing in the development and/or testing of CPC-based oral care formulations. Full article

Produced water (PW) generated from oil and gas operations poses a significant environmental challenge due to its high salinity and complex organic–inorganic composition. This study evaluates forward osmosis (FO) as an energy-efficient approach for PW treatment by comparing a commercial cellulose triacetate (CTA) membrane and a fabricated electrospun nanofibrous membrane, both modified with a zwitterionic sulfobetaine methacrylate/polydopamine (SBMA/PDA) coating. Fourier Transform Infrared Spectroscopy (FTIR) spectra verified the successful incorporation of SBMA and PDA through the appearance of characteristic sulfonate, quaternary ammonium, and catechol/amine-related vibrations. Scanning electron microscopy (SEM) imaging revealed the intrinsic dense surface of the CTA membrane and the highly porous nanofibrous architecture of the electrospun membrane, with both materials showing uniform coating coverage after modification. Complementary analyses supported these observations: X-ray Photoelectron Spectroscopy (XPS) confirmed the presence of nitrogen, sulfur, and chlorine containing functionalities associated with the zwitterionic layer; Thermogravimetric Analysis (TGA) demonstrated that surface modification did not compromise the thermal stability of either membrane; and contact-angle measurements showed substantial increases in surface hydrophilicity following modification. Gas chromatography–mass spectrometry (GC–MS) analysis of the Permian Basin PW revealed a chemically complex mixture dominated by light hydrocarbons, alkylated aromatics, and heavy semi-volatile organic compounds. FO experiments using hypersaline PW demonstrated that the fabricated membrane consistently outperformed the commercial membrane under both MgCl₂ and Na₃PO₄ draw conditions, achieving up to ~40% higher initial water flux and total solids rejection as high as ~62% when operated with 2.5 M Na₃PO₄. The improved performance is attributed to the nanofibrous architecture and zwitterionic surface chemistry, which together reduced fouling and reverse solute transport. These findings highlight the potential of engineered zwitterionic nanofibrous membranes as robust alternatives to commercial FO membranes for sustainable produced water treatment. Full article

Benzalkonium chloride (BC) is widely used as a disinfectant in the food industry; however, increasing reports of Listeria innocua isolates exhibiting tolerance to this compound highlight the need to better understand their adaptive mechanisms. This study aimed to evaluate BC tolerance in 51 L. innocua isolates originating from raw and processed meat products (n = 32) and meat-processing environments in Poland (n = 19). Phenotypic tolerance was assessed using the agar diffusion method on two media: Brain Heart Infusion (BHI) agar and Mueller–Hinton (M-H) agar supplemented with 1.2% sheep blood, across BC concentrations of 0, 5, 10, 15, 20, 25, 30, 35, 40, and 45 µg/mL, allowing the determination of minimum inhibitory concentrations (MICs). Genotypic analysis of tolerance determinants (brcABC, ermC, qacE, qacF, qacG, qacH, and qacJ) was performed by PCR. On BHI agar, MIC values ranged from 15 to 30 µg/mL, with 15 µg/mL most frequently observed, whereas on blood-supplemented M-H agar, MICs were lower (5–20 µg/mL), most commonly 10 µg/mL. Among tolerance-associated genes, qacH was the most prevalent (29% of isolates), followed by brcABC (4%) and ermC (2%), while the remaining genes were absent. These findings suggest that food products may serve as a reservoir for L. innocua isolates harboring tolerance to BC and contribute to a deeper understanding of how this species adapts to quaternary ammonium compounds. Full article

Sewage sludge is increasingly recognized as a major reservoir for pharmaceuticals and emerging contaminants that are only partially removed by conventional wastewater treatment. This study provides the first comprehensive assessment of these contaminants in biosolids generated from ten major wastewater treatment plants (WWTPs) across Jordan. Different pharmaceuticals were quantified in the sludge samples generated. The results revealed concentrations ranging from 10 to over 2000 µg kg⁻¹, with antibiotics typically showing the highest enrichment (e.g., ciprofloxacin up to 2165 µg kg⁻¹, ofloxacin up to 303 µg kg⁻¹). Anti-inflammatory compounds such as diclofenac reached 196 µg kg⁻¹, while the antimicrobial triclosan exceeded 4700 µg kg⁻¹ in some sludge samples. Carbamazepine, a recalcitrant antiepileptic drug, ranged between 50 and 223 µg kg⁻¹, reflecting both widespread use and strong persistence. Elevated levels of quaternary ammonium compounds (QACs) were also detected. The highest levels were generally associated with large urban WWTPs and plants receiving industrial discharges. Environmental risk assessment (ERA) indicated that the risk for soil biota was acceptable for most cases for low application doses (5–10 t/ha) except for WWTP6-MD, WWTP8-S, and WWTP9-IC, where the risk was non-acceptable. Severe limitations in the risk assessment were noted: reliable toxicity endpoints in terrestrial soil organisms such as microbiota, collembola, and earthworms are few, while deriving endpoints via aquatic available data is not always reliable. Overall, the findings demonstrate that Jordanian sewage sludge contains environmentally relevant levels of pharmaceuticals and QACs and that risk assessment is, therefore, pertinent before any stabilization and realistic land application scenarios are chosen. Full article

Bentonite is the most widely used raw material for producing organoclays, which have numerous industrial and environmental applications. Due to their hydrophobicity, high swelling, and strong affinity for organic compounds, organoclays are effective in removing organic solvents from contaminated water originating from pipeline leaks, oil spills, traffic accidents, and industrial discharges. Such contamination not only degrades water quality but also forms surface films that hinder oxygen transfer, threatening aquatic ecosystems. In this study, two sodium bentonites with different specific surface areas (30 and 50 m²/g) were modified with three quaternary ammonium salts of varying molar masses and alkyl chain lengths (Sun, Arq, and Arm) to evaluate their performance in organic solvent sorption (gasoline, diesel, and kerosene). The materials were characterized by X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential thermal analysis (DTA), scanning electron microscopy (SEM), and swelling capacity and sorption efficiency. The swelling capacity was determined according to ASTM D5890-19 (Foster method) using gasoline, diesel, kerosene, toluene, and xylene, while the sorption efficiency was assessed following ASTM F726-17 in gasoline, diesel, and kerosene, chosen due to their high potential for water contamination and frequent occurrence in oil spill and leakage scenarios. These solvents also differ in polarity and aromatic content, providing a relevant model for hydrocarbon mixtures commonly found in the environment. Results showed that the interaction between the clay and the surfactant depended strongly on the modifier’s chemical structure. The sorption capacity increased with greater interlayer expansion, surfactant molar mass, and specific surface area of the clay. Among all samples, the Arm-modified natural bentonite (VLArm) exhibited the best performance, with adsorption capacities of up to 6 g/g for diesel, 5 g/g for gasoline, and 5 g/g for kerosene. These values exceeded most previously reported organoclays. These findings demonstrate that optimizing the combination of clay properties and surfactant chemistry can yield highly efficient, low-cost organoclays for environmental remediation of organic contaminants. Full article

Background/Objectives: Deep eutectic solvents (DESs) have recently gained attention for their antimicrobial properties, particularly because they target both planktonic bacteria and biofilms. Among these, DESs based on α-hydroxy acids (αHAs) are of interest due to their inherent antibacterial properties and favorable biocompatibility. However, effects of the αHA molecular structure and hydrogen bonding ability within a DES formulation on biological activity has not yet been thoroughly investigated. Methods: This study systematically investigates DESs formed by combining glycolic acid, lactic acid or tartaric acid with either choline chloride or tetraethylammonium chloride. Results: All DESs demonstrate broad-spectrum antibacterial activity against Staphylococcus aureus, methicillin-resistant Staphylococcus aureus, Escherichia coli, and Pseudomonas aeruginosa and effectively inhibit biofilm formation while exhibiting low cytotoxicity toward 3T3-L1 fibroblasts. Conclusions: DES formation enhances antibacterial efficacy while attenuating cytotoxicity compared to the individual components, thereby decoupling bactericidal activity from toxicity. Physicochemical characterization confirms the formation of a eutectic phase and reveals that biological activity is primarily governed by acidity rather than by the specific αHA structure or eutectic strength. These results provide new insights into structure-function relationships in DESs and establish a design strategy for biocompatible, non-cytotoxic antimicrobial agents. Full article

Tomato brown rugose fruit virus (ToBRFV) has become a major threat to global tomato production due to its exceptional mechanical transmissibility and virion stability. Effective sanitation is essential for containment, yet the performance of commonly used disinfectants on greenhouse-relevant surfaces remains poorly characterized. This study evaluated multiple disinfectant formulations, applied by spraying or dipping, on polyethylene film, pruning shears, and human hands. After controlled inoculation with a standardized inoculum, treated surfaces were swabbed and extracts mechanically inoculated onto Nicotiana rustica L. Lesion number was visually quantified, and lesion area was measured using a computational image-analysis pipeline. Fifth-generation quaternary ammonium compounds (5°QAS) showed the highest virucidal activity on smooth, non-porous surfaces, reducing lesion numbers to fewer than 10 per leaf at 800–1000 ppm and maintaining infection severities below 1%. Glutaraldehyde at 500 ppm also performed strongly, achieving severities as low as 0.20% on plastic. Metallic pruning shears consistently retained infectious particles, with untreated controls exceeding 100 lesions per leaf and treated samples showing incomplete inactivation. Mechanical agents such as powdered milk and soap reduced infection but did not eliminate transmission. No clear dose–response trend was observed. The two most effective treatments, 5°QAS at 800–1000 ppm and glutaraldehyde at 500 ppm, significantly reduced or prevented systemic infection in tomato assays. These findings demonstrate that sanitation efficacy depends on formulation, surface type, and application method, providing operationally relevant guidelines for ToBRFV management. Full article