Search Results (1,286)

To promote sustainable wastewater treatment, this study developed an eco-friendly and low-cost ozone catalyst using natural zeolite for the advanced treatment of petrochemical wastewater. The Ca-Cu/zeolite catalyst (0.75 mol/kg Ca and 0.25 mol/kg Cu) demonstrated high efficiency in catalytic ozonation, achieving 55.52% TOC removal under optimized conditions (ozone dosage: 108.0 mg/(L·h), catalyst dosage: 406.0 g/L, reaction time: 90 min). Compared to ozonation alone, the catalyst enhanced oxidation rates by 10 times, promoting ozone decomposition into reactive oxygen species (e.g., OH and ¹O₂) while improving gas–liquid–solid mass transfer for efficient pollutant mineralization. Remarkably, the natural zeolite-based catalyst exhibited superior sustainability: compared to conventional alumina-based catalysts, its production cost (4000–4500 CNY/ton) is 44–53% lower, while its carbon footprint (533.7 kg CO₂/ton) is reduced by 45.4%. This work presents a sustainable, low-carbon, and economically viable catalytic ozonation solution, contributing to the development of green and cost-effective industrial wastewater treatment technologies. Full article

Aluminum powder is the most commonly used metal fuel in the industry of explosives and propellants. The research progress in preparation technology, reactivity and application of nano-aluminum in explosives and propellants is systematically reviewed in this paper. The preparation technology of nano-aluminum powder includes mechanical pulverization technology (such as the ball milling method and ultrasonic ablation method, etc.), evaporation condensation technology (such as the laser induction composite heating method, high-frequency induction method, arc method, pulsed laser ablation method, resistance heating condensation method, gas-phase pyrolysis method, wire explosion pulverization method, etc.), chemical reduction technology (such as the solid-phase reduction method, solution reduction method, etc.) and the ionic liquid electrodeposition method, each of which has its own advantages. Some new preparation methods have emerged, providing important reference value for the large-scale production of high-purity, high-quality nano-aluminum powder. The reactivity differences between nano-aluminum powder and micro-aluminum powder are compared in the thesis. It is clear that the reactivity of nano-aluminum powder is much higher than that of micro-aluminum powder in terms of ignition performance, combustion performance and reaction completeness, and it has a stronger influence on the detonation performance of mixed explosives and the combustion performance of propellants. Nano-aluminum powder is highly prone to oxidation, which seriously affects its application efficiency. In addition, when aluminum powder oxidizes or burns, a surface oxide layer will be formed, which hinders the continued reaction of internal aluminum powder. In addition, nano-aluminum powder may deteriorate the preparation process of explosives or propellants. To improve these shortcomings, appropriate coating or modification treatment is required. The application of nano-aluminum powder in mixed explosives can improve many properties of mixed explosives, such as detonation velocity, detonation heat, peak value of shock wave overpressure, etc. Applying nano-aluminum powder to propellants can significantly increase the burning rate and improve the properties of combustion products. It is pointed out that the high reactivity of nano-aluminum powder makes the preparation and storage of high-purity nano-aluminum powder extremely difficult. It is recommended to increase research on the preparation and storage technology of high-purity nano-aluminum powder. Full article

The article presents experimental data on the electrochemical oxidation of vanadium-bearing ore with the aim of increasing the efficiency of vanadium extraction during subsequent hydrometallurgical processing. Three different charge compositions were studied during the preliminary oxidative roasting stage, differing in the type of oxidizers used: calcined soda, sodium chloride, and their mixture in a mass ratio of 9:1. Electrochemical oxidation was carried out in a sulfuric acid medium using a membrane electrolysis cell equipped with an MK-40 type diaphragm. Experimental studies were conducted by varying key technological parameters: H₂SO₄ concentration (5–15%), solid-to-liquid phase ratio (1:2–1:5), temperature (25–85 °C), process duration (0.5–3 h), and current density (100–1000 A/m²). It was found that preliminary roasting promotes the conversion of vanadium into higher oxidation states, predominantly V⁵⁺, which significantly increases its solubility during subsequent electrochemical treatment. For the first time, the kinetic patterns of electrochemical vanadium leaching were identified, as well as the limiting mechanism of the process, associated with the formation of poorly soluble oxide films on the ore surface. Optimization of the electrochemical oxidation parameters allowed us to achieve vanadium extraction into solution up to 92%. Full article

Ceramic matrix composites (CMCs) are extensively utilized in aero engines due to their high-temperature stability; however, they are prone to environmental corrosion at high temperatures, and environmental barrier coatings (EBCs) are necessary to resist oxidation and corrosion. Among various EBC materials, AlTaO₄ offers high cost-effectiveness and low thermal expansion coefficients (TECs), but its resistance to SiO₂ erosion and high-temperature stability remain unclear. We investigated the influences of SiO₂ additions on the structures and thermal properties of AlTaO₄; and AlTaO₄ mixtures containing 10 wt.% SiO₂ were kept at 1400 °C for 30–120 h. AlTaO₄ exhibited excellent high-temperature phase stability, and SiO₂ dissolved into AlTaO₄ to generate a solid solution. XRD Rietveld refinement was employed to confirm the position of Si in the lattices, while SEM and EDS characterizations demonstrated the homogeneous distribution of Si, Al, and Ta elements. At 1200 °C, the TECs of SiO₂-AlTaO₄ (4.65 × 10⁻⁶ K⁻¹) were close to those of SiC (4.5–5.5 × 10⁻⁶ K⁻¹). Additionally, the addition of SiO₂ could reduce TECs of AlTaO₄, a feature that helped alleviate the interface thermal stress between AlTaO₄ and the Si bond coat in the EBC systems. At 900 °C, the thermal conductivity was reduced by 26.9% compared to that of AlTaO₄, and the lowest value was 1.65 W·m⁻¹·K⁻¹. Accordingly, SiO₂ will enter the lattices of AlTaO₄ after heat treatments at 1400 °C, and SiO₂ additions will reduce the thermal conductivity and TECs of AlTaO₄, which is beneficial for its EBC applications. Full article

Local communities in many parts of the West Bank, Palestine have very limited water resources available for irrigation. In addition, since these communities are traditionally agricultural communities, water shortage and the lack of innovation in the agricultural sector led to loss of jobs in this sector. This in turn led young people to start looking for jobs in different sectors and even increased migration to urban centers. The reuse of treated wastewater can provide a viable solution to irrigation water shortage. It can help in creating jobs in the marginalized communities in the West Bank, especially in areas under full Israeli control (Area C according to the Oslo Accord). Furthermore, it is important to select crops that can resist the effects of climate change and create revenue for the farmers at the same time. In this research, we studied the impact of irrigating marigold (Tagetes erecta), which is a flower plant commonly used in the Palestinian market, with treated wastewater from the Nablus West Wastewater Treatment Plant (NWWTP). The quality of the treated wastewater, as indicated by parameters such as COD, BOD5, pH, EC, and TSS, shows its suitability for agricultural reuse. With low levels of organic matter, a near-neutral pH, and minimal suspended solids, the water poses minimal environmental risks and is ideal for irrigation, though monitoring for salinity buildup is necessary. Twenty-six marigold plants were planted, half of them were irrigated with the treated wastewater and the other half with tap water. Observations of length, number of roses, rose size, days to flower, and flowering days were recorded for both cases. The statistical analysis of the results shows that there is no significant difference between marigolds irrigated with treated wastewater and those treated with tap water, in terms of Plant Height, Rose Number and Rose Diameter. Full article

Balancing soil nitrogen leaching with production benefits remains a critical challenge in sustainable greenhouse tomato cultivation. This study evaluated the effects of reduced water-soluble nitrogen fertilizer (N) application rates on soil environmental parameters and production outcomes to optimize nitrogen management strategies. Four treatments were implemented across two growing seasons: control (CK), high-N (H), medium-N (M), and low-N (L) nitrogen fertilizer applications in soil solution (SS) and autumn–winter (AW) systems. Results demonstrated that reduced nitrogen inputs significantly decreased soil electrical conductivity and soil nitrogen retention by 88% and 83% in SS and AW, respectively, while reducing soil residual nitrate nitrogen. The tomato yield decreased by 14–26% under low fertilizer treatment, while fruit quality was substantially enhanced, with soluble solid content increasing by 56% in SS and 217% in AW for the L treatment compared to the CK. Nitrogen-use efficiency improved by 54.7% and 34.78% in SS and AW, respectively, demonstrating superior resource utilization under reduced fertilizer applications. Principal component analysis revealed that fruit quality was primarily influenced by soluble solid content, organic acid, total soluble solids, and sugar–acid ratio. Gray relational analysis identified the L treatment (361.62 kg ha⁻¹ in SS and 182.6 kg ha⁻¹ in AW) as optimal for comprehensive performance evaluation. The findings demonstrate that strategic nitrogen reduction effectively balances production benefits with environmental sustainability, providing a practical framework for sustainable nitrogen management in controlled environment agriculture. Full article

The growing demand for lithium-ion batteries (LIBs) requires efficient and sustainable recycling solutions. This study investigates bioleaching as an alternative to conventional hydrometallurgical methods, focusing on (i) organic acid-mediated leaching with Gluconobacter oxydans and (ii) sulfuric acid bioleaching with Acidithiobacillus thiooxidans. Experiments were conducted at 26 °C with leaching durations of one to three weeks, depending on the microbial system, at pH 1.35 for sulfuric acid treatments, and with liquid-to-solid ratios equivalent to 100 mL g⁻¹ (A. thiooxidans) or 100 mL g⁻¹ in culture medium (G. oxydans). Results show that indirect bioleaching with G. oxydans achieved high recovery rates for cobalt (96%), manganese (100%), nickel (65%), and lithium (68%), while the direct approach was less effective due to microbial inhibition by black mass components. Similarly, biologically produced sulfuric acid exhibited moderate leaching efficiencies, but chemically synthesized sulfuric acid outperformed it, particularly for nickel (93%) and lithium (76%) after one week of leaching. These findings suggest that bioleaching is a promising, eco-friendly alternative for LIB recycling but requires further process optimization to improve metal recovery and industrial scalability. Future research should explore hybrid approaches combining bioleaching with conventional leaching techniques. Full article

The use of molybdenum-based alloys as materials for components operating under high temperatures and significant mechanical loads is widely recognized due to their excellent mechanical properties. However, their low high-temperature resistance remains a critical limitation, which can be effectively mitigated by applying protective coatings. In this study, we investigate the influence of a two-step coating process on the properties and performance of the TZM molybdenum alloy. In the first step, pack cementation was performed. Simultaneous surface saturation with aluminum and silicon, a process known as aluminosiliconizing, was conducted at 1000 °C for 6 h. The saturating mixture comprised powders of aluminum, silicon, aluminum oxide, and ammonium chloride. The second step involved the application of a pre-ceramic coating based on polyhydrosiloxane modified with silicon and boron. This treatment effectively eliminated pores and cracks within the coating. Thermodynamic calculations were carried out to evaluate the likelihood of aluminizing and siliconizing reactions under the applied conditions. Aluminosiliconizing of the TZM alloy resulted in the formation of a protective layer 20–30 µm thick. The multiphase structure of this layer included intermetallics (Al₆₃Mo₃₇, MoAl₃), nitrides (Mo₂N, AlN, Si₃N₄), oxide (Al₂O₃), and a solid solution α-Mo(Al). Subsequent treatment with silicon- and boron-modified polyhydrosiloxane led to the development of a thicker surface layer, 130–160 µm in thickness, composed of crystalline Si, amorphous SiO₂, and likely amorphous boron. A transitional oxide layer ((Al,Si)₂O₃) 5–7 µm thick was also observed. The resulting coating demonstrated excellent structural integrity and chemical inertness in an argon atmosphere at temperatures up to 1100 °C. High-temperature stability at 800 °C was observed for both coating types: aluminosiliconizing, and aluminosiliconizing followed by the pre-ceramic coating. Moreover, additional oxide layers of SiO₂ and B₂O₃ formed on the two-step coated TZM alloy during heating at 800 °C for 24 h. These layers acted as an effective barrier, preventing the evaporation of the substrate material. Full article

The direct deposition of highly concentrated polyelectrolyte complexes based on poly(ethyleneimine) (PEI) and poly(sodium methacrylate) (PMANa) onto inorganic sand microparticles (F100 and F200) resulted in the formation of versatile core-shell composites with fast removal properties in dynamic conditions toward anionic charged pollutants. Herein, in situ-generated nonstoichiometric PEI/PMANa polyelectrolyte complexes were directly precipitated as a soft organic shell onto solid sand microparticles at a 5% mass ratio (organic/inorganic part = 5%, w/w%). The sorption of an anionic model pollutant (Indigo Carmine (IC)) onto the composite particles in dynamic conditions depended on the inorganic core size, the flow rate, the bed type (fixed or fluidized) and the initial dye concentration. The maximum sorption capacity, after 10 cycles of sorption/desorption of IC onto F100@P5% and F200@P5%, was between 16 and 18 mg IC/mL composite. The newly synthesized core-shell composites could immobilize IC at a high flow rate (8 mL/min), either from concentrated (C_IC = 60 mg/L) or very diluted (C_IC = 0.2 mg/L) IC aqueous solution, demonstrating that this type of material could be promising in water treatment or efficient in solid-phase extraction (concentration factor of 2000). Full article

Dendritic cells (DCs) are critical antigen-presenting cells that orchestrate the interface between innate and adaptive immunity, making them attractive approaches for cancer immunotherapy. Recent advances in the characterization of DC subsets, antigen delivery strategies, and adjuvant design have enabled the enhancement of DC-based vaccines for solid tumors. Clinical studies across melanoma, glioblastoma, prostate cancer, and non-small cell lung cancer have demonstrated safety and immunogenicity, with encouraging signals of clinical efficacy, particularly when DC vaccination is combined with immune checkpoint blockade or personalized neoantigen approaches. However, translational barriers remain, including the immunosuppressive tumor microenvironment, inefficient DC migration, and variability in manufacturing protocols. Developing solutions such as in vivo DC targeting, biomaterials-based delivery systems, high-resolution single-cell analyses, and artificial intelligence-driven epitope prediction are controlled to overcome these challenges. Together, these innovations highlight the evolving role of DC immunotherapy as a foundation of precision oncology, offering the potential to integrate personalized vaccination strategies into standard treatment paradigms for solid tumors. Therefore, in this review, we specifically focus on these advances in dendritic cell immunotherapy for solid tumors and their translational implications. Full article

This study investigates the enhancement of polyvinylidene fluoride (PVDF) membranes with polyethylene glycol (PEG) to improve their efficacy in treating tofu wastewater through the ultrafiltration (UF) process. PVDF membranes with varying PEG concentrations of 0, 0.5, 1, and 1.5% in the dope solution were produced, characterized via FTIR, mechanical strength, porosity, and contact angle measurements, and evaluated in wastewater treatment at varying pressures of 3, 4, and 5 bar in the UF process. The incorporation of PEG increased the membrane’s porosity from 28.2% for M-0 to 43.5% for M-1.5. The contact angle decreased from 65.3° for M-0 to 53.3° for M-1.5, indicating an increase in hydrophilicity. Elongation increased from 36.0% for M-0 to 113.5% for M-1.5; however, the tensile strength decreased from 11.8 MPa for M-0 to 5.4 MPa for M-1.5. Although PEG-modified membranes demonstrated enhanced flux, with values of 6.3 L∙m⁻²∙h⁻¹ for M-0 and 15.7 L∙m⁻²∙h⁻¹ for M-1.5 at a pressure of 5 bar, pure PVDF membranes (M-0) showed greater rejection rates for chemical oxygen demand (COD), total dissolve solid (TDS), total suspended solid (TSS), and turbidity at 3 bar, achieving values of 66.3%, 41.6%, 99.6%, and 99.1%, respectively. Following ultrafiltration, the pH and TDS levels conformed to Indonesian government guidelines; however, the COD levels were non-compliant, indicating the need for additional treatment. The findings suggest that PVDF/PEG ultrafiltration membranes are suitable for pre-treatment; however, nanofiltrationor reverse osmosis may be necessary to meet the stringent regulatory standards for tofu wastewater treatment. The modified M-1.5 membrane is recommended as the primary ultrafiltration membrane for tofu wastewater treatment due to its superior flux, prior to nanofiltration or reverse osmosis, to comply with the stringent regulatory standards established by the Government of the Republic of Indonesia. Full article

This study investigated the effects of silver doping, natural ageing, and thermal-induced oxidation on the surface chemistry, morphology, and thermal performance of copper thin films. Ag is used as a doping element in Cu because, in bulk materials it usually refines microstructures, leading to increased hardness and mechanical strength through mechanisms such as solid solution strengthening and twinning. In this work was also used due to its oxidation resistance. Thin films of pure and silver-doped copper (Cu_2Ag and Cu_4Ag) were deposited by RF magnetron sputtering and characterized as-deposited, naturally aged, at room temperature and humidity for one year, and thermally treated at 200 °C, in air. The characterization included X-ray photoelectron spectroscopy (XPS), Atomic Force microscopy (AFM), and thermal analysis, specifically thermal conductivity (λ), thermal diffusivity (α), and thermal capacity (ρ.Cp). Surface XPS analysis revealed changes in copper and silver oxidation states after natural aging and annealing. AFM revelead that the incorporation of silver and heat treatment altered the surface roughness and morphology. Thermal analysis found that for lower silver concentrations, the thermal conductivity increased, but aging and annealing had varying effects depending on the silver content. The Cu_4Ag film showed the best thermal stability after natural ageing. Overall, the results suggest that carefully controlled silver doping can enhance the thermal stability of copper thin films for applications where aging is a concern, such as microelectronics. Full article

Carbon microspheres were prepared by microwave-assisted hydrothermal treatment, at 180 °C, of commercial carbohydrates (saccharose, glucose, and xylose) and xylose extract obtained from almond shells with varying synthesis parameters. When 1.6 M aqueous solutions of commercial carbohydrates were used, 2–10 μm carbon microspheres were obtained from saccharose after 15 min, while a longer amount of time (60 min) and the addition of acid medium (1% v/v H₂SO₄, 1% v/v H₃PO₄) were needed to obtain carbon microspheres from commercial xylose and glucose (≤ 1 μm). The higher reactivity of saccharose could be related to the formation, during heating, of fructose, which is more reactive than glucose and xylose. An increase in the acid concentration and in the carbohydrate concentration increased the formation and size of the microspheres. Comparative experiments with conventional heating did not produce a solid. Interestingly, when xylose extract obtained from almond shells was used, small carbon microspheres (1–3 μm) were obtained at a much lower concentration (0.2 M) and time (15 min) than with commercial xylose. This could be related to the acid medium used during extraction of xylose from the biomass. Activation of microspheres with CO₂ resulted in high-surface area materials (243–326 m²/g) with great potential as catalytic supports. Full article

Water pollution continues to pose a critical global challenge, largely due to the unregulated discharge of industrial, agricultural, and municipal effluents. Among emerging solutions, enzymatic bioremediation stands out as a sustainable and environmentally friendly approach, offering high specificity and efficiency under mild conditions. Nonetheless, the practical application of free enzymes is hindered by their inherent instability, poor reusability, and susceptibility to denaturation. To address these limitations, the immobilization of enzymes onto solid supports, particularly clay minerals, has garnered increasing attention. This review presents a detailed analysis of clay minerals as promising carriers for enzyme immobilization in wastewater treatment. It explores their classification, structural characteristics, and physicochemical properties, highlighting key advantages such as a large surface area, cation exchange capacity, and thermal stability. Functionalization techniques, including acid/base activation, intercalation, grafting, and pillaring, are discussed in terms of improving enzyme compatibility and catalytic performance. Various immobilization methods such as physical adsorption, covalent bonding, entrapment, crosslinking, and intercalation are critically evaluated with regard to enhancing enzyme activity, stability, and recyclability. Recent case studies demonstrate the effective removal of pollutants such as dyes, pharmaceuticals, and heavy metals using enzyme–clay composites. Despite these advances, challenges such as enzyme leaching, mass transfer resistance, and variability in clay composition persist. This review concludes by outlining future prospects, including the development of hybrid and magnetic clay-based systems and their integration into advanced water treatment technologies. Overall, enzyme immobilization on clay minerals represents a promising and scalable approach for the next generation of wastewater bioremediation strategies. Full article

Objective: This scoping review synthesized and mapped the breadth of the existing literature on technological resources used to support individuals undergoing hemodialysis treatment. Methods: Following the methodological guidelines of the Joanna Briggs Institute (JBI) for scoping reviews and the Preferred Reporting Items for Systematic Reviews and Meta-Analyses extension for Scoping Reviews (PRISMA-ScR) checklist, comprehensive searches were conducted across the following databases: MEDLINE, Cumulative Index to Nursing and Allied Health Literature (CINAHL), PsycINFO, Scopus, Scientific Electronic Library Online (SciELO), MedicLatina, and the Cochrane Central Register of Controlled Trials, with no time restrictions. Results: Thirty-nine studies conducted between 2003 and 2023 met the inclusion criteria. These studies covered a range of technological innovations developed specifically for hemodialysis treatment, including virtual reality, exergames, websites, and mobile applications. These technologies were designed with diverse objectives: to facilitate physical exercise, optimize dietary and medication management, improve disease adherence and management, and promote self-efficacy and self-care in patients. Conclusions: The review revealed a wide range of technological resources available to hemodialysis patients. These digital solutions show great potential to transform care by promoting more engaged and personalized health practices. Although this study did not directly assess the impact of these technologies, it provides a solid foundation for future investigations that can explore in-depth how such innovations contribute to effective disease management and improvement in clinical outcomes. Full article