Search Results (476)

In additively manufactured (AM) Ti-6Al-4V, the role of martensitic α′ in governing brittleness versus toughness remains debated, largely because complex thermal histories and other intertwined physical factors complicate interpretation. To isolate and clarify the intrinsic effect of cooling rate, we employed a Gleeble thermal simulator, which enables precisely controllable cooling rates while simultaneously achieving ultra-fast quenching comparable to AM (up to ~7000 °C/s). By varying the cooling rate only, three distinct microstructures were obtained: α/β, α_m/α′, and fully α′. Compression tests revealed that the ultra-fast-cooled fully martensitic Ti-6Al-4V attained both higher strength and larger fracture strain, with densely distributed elongated dimples indicative of ductile failure. Three-dimensional microstructures reconstructed from microscopy, analyzed using an EVP-FFT crystal plasticity model, demonstrated that refined α′ laths and abundant high-angle boundaries promote more homogeneous strain partitioning and reduce stress triaxiality, thereby delaying fracture. These results provide potential evidence that extreme-rate martensitic transformation can overcome the conventional strength–ductility trade-off in Ti-6Al-4V, offering a new paradigm for processing titanium alloys and AM components with superior performance. Full article

Argillaceous slate (AS) is a typical metamorphic rock with well-developed bedding, widely distributed globally. Its bedding structure significantly impacts slope stability assessment, and the challenges associated with slope anchoring and support arising from bedding characteristics have become a focal point in the engineering field. In this study, with bedding dip angle as the key variable, mechanical tests such as uniaxial compression, triaxial compression, direct shear, and Brazilian splitting tests were conducted on AS. Additionally, field anchoring grouting diffusion tests on AS slopes were carried out. The aim is to investigate the basic mechanical properties of AS and the grout diffusion law under different bedding dip angles. The research results indicate that the bedding dip angle has a remarkable influence on the failure mode, stress–strain curve, and mechanical indices such as compressive strength and elastic modulus of AS specimens. The stress–strain curves in uniaxial and triaxial tests, as well as the stress-displacement curve in the Brazilian splitting test, all undergo four stages: crack closure, elastic deformation, crack propagation, and post-peak failure. As the bedding dip angle increases, the uniaxial and triaxial compressive strengths and elastic modulus first decrease and then increase, while the splitting tensile strength continuously decreases. The consistency of the bedding in AS causes the grout to diffuse in a near-circular pattern on the bedding plane centered around the borehole. Among the factors affecting the diffusion range of the grout, the bedding dip angle and grouting angle have a relatively minor impact, while the grouting pressure has a significant impact. A correct understanding and grasp of the anisotropic characteristics of AS and the anchoring grouting diffusion law are of great significance for slope stability assessment and anchoring design in AS areas. Full article

With the deepening implementation of the coordinated development strategy for energy exploitation and ecological conservation, green coal mining technology has become a critical pathway to achieve balanced resource development and environmental protection. This study investigates the stress field evolution and dynamic fracture propagation mechanisms in overlying strata during shallow coal seam mining in the Shenfu mining area. By employing a multidisciplinary approach combining triaxial compression tests (0–15 MPa confining pressure), scanning electron microscopy (SEM) microstructural characterization, elastoplastic theoretical modeling, and FLAC3D numerical simulations, the synergistic failure mechanisms of overlying strata were systematically revealed. Gradient-controlled triaxial tests demonstrated significant variations in stress-strain responses across lithological types. Notably, Class IV sandstone exhibited exceptional uniaxial compressive strength of 106.7 MPa under zero confining pressure, surpassing the average strength of Class I–III sandstones (86.2 MPa) by 23.6%, attributable to its highly compacted grain structure. A nonlinear regression-derived linear strengthening model quantified that each 1 MPa increase in confining pressure enhanced axial peak stress by 4.2%. SEM microstructural analysis established critical linkages between microcrack networks/grain-boundary slippage at the mesoscale and macroscopic brittle failure patterns. Numerical simulations demonstrated that strata failure manifests as tensile-shear composite fractures, with lateral crack propagation inducing bed separation spaces. The stress field exhibited spatiotemporal heterogeneity, with maximum principal stress concentrating near the initial mining cut during early excavation. Fractures propagated obliquely at angles of 55–65° to the horizontal plane in an ‘inverted V’ pattern from the goaf boundaries, extending vertically 12–18 m before transitioning to the bent zone, ultimately forming a characteristic three-zone structure. Experimental and simulated vertical stress distributions showed minimal deviation (≤2.8%), confirming constitutive model reliability. This research quantitatively characterizes the spatiotemporal synergy of strata failure mechanisms in ecologically vulnerable northwestern China, proposing a confining pressure-effect quantification model for support parameter optimization. The revealed fracture dynamics provide critical insights for determining ecological restoration timelines, while establishing a novel theoretical framework for optimizing green mining systems and mitigating ecological damage in the Shenfu mining area. Full article

To improve the engineering properties of red clay, sodium polyacrylate (PAAS) and locust bean gum (LBG) were used as modifiers, either singly or in combination. The modified soils were subjected to variable head permeability tests, triaxial compression tests, and scanning electron microscopy (SEM) tests to analyze the effects of different modifiers on the permeability and shear strength of the red clay and systematically explore the modification mechanism. The results showed that both PAAS and LBG significantly reduced the permeability of the red clay, with PAAS having a more pronounced effect. This mechanism is attributed to PAAS swelling upon water absorption, forming a hydrogel network that fills micropores and forms ionic bonds with clay particles. LBG, on the other hand, encapsulates the particles in a highly viscous colloid, enhancing their aggregation. Regarding shear strength, both PAAS and LBG improved soil cohesion, with PAAS exhibiting a superior combined improvement in cohesion and internal friction angle compared to LBG. The PAAS-LBG composite modification exhibits a significant synergistic effect: PAAS forms a continuous hydrogel network as the primary skeletal structure of the soil, while LBG supplements the pores and increases bonding, resulting in a denser soil structure. Microscopic analysis further confirms that the PAAS-LBG composite modification significantly reduces porosity and enhances interparticle interlocking, thereby simultaneously improving both the impermeability and shear strength of the red clay. This research can provide a reference for sustainable development and red clay modification in red clay regions. Full article

The creep failure of open-pit mine slopes with weak interlayers is one of the main types of slope instability in open-pit mines. The scientific and reasonable treatment of this type of landslide is of great significance for improving the quality of open-pit mining. In this study, we study a gently inclined and creep-type slope with weak interlayers in an open-pit mine in Inner Mongolia, China, and conduct systematic on-site engineering geological investigations, laboratory tests, and numerical simulations. The particle swarm optimization algorithm is introduced, and the creep model combining Burgers and Mohr–Coulomb is selected. Combined with triaxial compression creep test data, the creep model parameters of the weak interlayer soil are intelligently inverted. A typical profile is selected to analyze the stability of the slope. The results show that the creep of the weak interlayer is the main controlling factor for the deformation and failure of the slope. Under natural conditions, a clear continuous plastic zone appears at the front edge of the weak interlayer and the rear edge of the sliding body, resulting in slope instability and large deformation. Our results are in good agreement with the reality of engineering. Furthermore, we study the effectiveness of the local reinforcement treatment method for the weak interlayer. This study shows that local reinforcement of the weak interlayer is one of the most economical and effective means of preventing and controlling landslides. After reinforcement, the plastic zone of the slope only appears near the rear edge of the sliding body and the reinforced rock mass, with a poor connection, and the stability of the slope is good. Our results provide effective technical support for the treatment of this slope and offer a reference for the disaster prevention and mitigation of gently inclined and creep-type open-pit mine slopes with weak interlayers. Full article

This study aims to evaluate the usability of agricultural wastes such as rice husk ash (RHA) and garlic husk ash (GHA) in improving silt soils by the alkali activation method. During the stabilization process, samples prepared with binder systems containing sodium hydroxide (SH) and sodium silicate (SS) at different SH/SS ratios (1, 3, and 9) and additive rates (0%, 4.5%, and 9%) were cured in two different curing environments (cured at ambient temperature—AC and cured in oven at 35 °C—OC) for 7, 28, 56, and 90 days. Mechanical behavior was evaluated by unconfined compressive strength (UCS) and unconsolidated-undrained triaxial compression (UU) tests; environmental strength was analyzed by 25 and 50 cycles of freeze–thaw (F–T) tests. Microstructure development was investigated by SEM and XRD analyses, while sustainability assessment was carried out with carbon footprint (kg·CO₂/kg) and carbon efficiency (CI) parameters. The findings showed that mixtures containing 9% RHA and a high SH/SS ratio provided high strength in both AC and OC environments. While using GHA alone provided limited mechanical performance, it increased the binding capacity by creating a synergistic effect when used with RHA. Oven-curing environment increased the speed of pozzolanic reactions and the development of the binder phase, resulting in denser microstructures. In addition, the RHA additive played a critical role in maintaining the resistance against freeze–thaw cycles. Carbon emission analyses revealed that SH and SS had high carbon loads, while RHA and GHA additives provided environmentally sustainable solutions with low carbon footprint and high strength. As a result, alkaline activation systems with RHA and GHA additives offer a strong alternative for sustainable soil improvement applications with high strength and environmental durability. Full article

Laboratory triaxial tests are essential for studying sandy soil behavior but have limited ability to capture localized deformation and microstructural evolution. The discrete element method (DEM) overcomes these limitations by enabling particle-scale analysis, where boundary conditions can critically affect simulation results. This study employed DEM-based triaxial compression simulations to compare rigid wall and flexible membrane boundaries for sand specimens with initial porosities of 35.5%, 38.2%, 40.8%, and 41.5% under confining pressures of 50, 100, and 150 kPa. The analyses covered macroscopic stress–strain and volumetric responses, shear band morphology, local porosity evolution, and contact force fabric. The results indicate that rigid and flexible boundaries produce similar pre-peak responses, but differ markedly in post-peak behavior and volumetric strain. Rigid boundaries constrain lateral deformation, induce stress concentrations, and underestimate post-peak strength, while flexible membranes apply confining pressure more uniformly and reproduce realistic bulging and porosity evolution. Based on these findings, rigid boundaries are suitable for dense sands when post-peak strength is not a concern, and for loose sands at small strains, whereas flexible membranes are necessary to capture volumetric contraction and realistic post-peak responses. This work provides mechanistic insights into boundary effects and offers a basis for more efficient selection of boundary conditions in DEM triaxial simulations. Full article

Microbial Induced Carbonate Precipitation (MICP) is regarded as a promising eco-friendly alternative to traditional Portland cement for soil stabilization. However, the feasibility of applying bio-cemented soil as a road base material remains inadequately studied, particularly in terms of the relationships between MICP treatment parameters—such as solution content, curing age, and the ratio of bacterial solution (BS) to cementation solution (CS) —and key mechanical and durability properties under realistic road conditions. In this study, an optimal curing condition for bio-cemented sand was first determined through unconfined compression strength (UCS) tests and calcium carbonate content (CCC) determination. Subsequently, dynamic triaxial tests were conducted to evaluate its resistance to cyclic loading. Further road performance tests, including splitting tensile strength, freeze-thaw resistance, temperature shrinkage, and arch expansion assessments, were carried out to comprehensively evaluate the material’s applicability. Scanning electron microscopy (SEM) was employed to elucidate the microstructural mechanisms underlying strength development. The results show that the strength (4.28 MPa) of bio-cemented sand cured under optimal conditions (12% bio-cured solution content, a BS-to-CS ratio of 1:4 and 7-d curing age) satisfies the criteria for road base applications. MICP treatment significantly improved the dynamic properties of aeolian sand (AS), reducing the cumulative plastic axial strain (ε_p) by nearly 11–46% and increasing the dynamic elastic modulus (E_d) by approximately 7–31% compared to untreated sand. The material also demonstrates satisfactory performance across all four road performance metrics. Microstructural analysis reveals enhanced interparticle bonding due to calcium carbonate precipitation, with samples prepared near the optimum moisture content exhibiting superior integrity and strength. Overall, bio-cemented sand demonstrates excellent potential as a sustainable road base material. These findings provide a theoretical foundation for practical applications of similar bio-cemented soils in road engineering. Full article

In the mining of deep mineral resources and tunnel engineering, the degradation of mechanical properties and the evolution of energy of through-double-joint sandy slate under triaxial loading and unloading conditions are key scientific issues affecting the stability design of the project. The existing research has insufficiently explored the joint inclination angle effect, damage evolution mechanism, and energy distribution characteristics of this type of rock mass under the path of increasing axial pressure and removing confining pressure. Based on this, in this study, uniaxial compression, conventional triaxial compression and increasing axial pressure, and removing confining pressure tests were conducted on four types of rock-like materials with prefabricated 0°, 30°, 60°, and 90° through-double-joint inclinations under different confining pressures. The axial stress/strain curve, failure characteristics, and energy evolution law were comprehensively analyzed, and damage variables based on dissipated energy were proposed. The test results show that the joint inclination angle significantly affects the bearing capacity of the specimen, and the peak strength shows a trend of first increasing and then decreasing with the increase in the inclination angle. In terms of failure modes, the specimens under conventional triaxial compression exhibit progressive compression/shear failure (accompanied by rock bridge fracture zones), while under increased axial compression and relief of confining pressure, a combined tensioning and shear failure is induced. Moreover, brittleness is more pronounced under high confining pressure, and the joint inclination angle also has a significant control effect on the failure path. In terms of energy, under the same confining pressure, as the joint inclination angle increases, the dissipated energy and total energy of the cemented filling body at the end of triaxial compression first decrease and then increase. The triaxial compression damage constitutive model of jointed rock mass established based on dissipated energy can divide the damage evolution into three stages: initial damage, damage development, and accelerated damage growth. Verified by experimental data, this model can well describe the damage evolution characteristics of rock masses with different joint inclination angles. Moreover, an increase in the joint inclination angle will lead to varying degrees of damage during the loading process of the rock mass. The research results can provide key theoretical support and design basis for the stability assessment of surrounding rock in deep and high-stress plateau tunnels, the optimization of support parameters for jointed rock masses, and early warning of rockburst disasters. Full article

The tight conglomerate oil reservoir in Xinjiang’s Mahu area is situated on the northwestern margin of the Junggar Basin. The reservoir comprises five stacked fan bodies, with the Triassic Baikouquan Formation serving as the primary pay zone. To delineate the study scope and conduct a field validation, the Ma-X well block was selected for investigation. Through triaxial compression tests and large-scale true triaxial hydraulic fracturing simulations, we analyzed the failure mechanisms of tight conglomerates and identified key factors governing hydraulic fracture propagation. The experimental results reveal several important points. (1) Gravel characteristics control failure modes: Larger gravel size and higher content increase inter-gravel stress concentration, promoting gravel crushing under confining pressure. At low-to-medium confining pressures, shear failure primarily occurs within the matrix, forming bypassing fractures around gravel particles. (2) Horizontal stress differential dominates fracture geometry: Fractures preferentially propagate as transverse fractures perpendicular to the wellbore, with stress anisotropy being the primary control factor. (3) Injection rate dictates fracture complexity: Weakly cemented interfaces in conglomerates lead to distinct fracture morphologies—low rates favor interface activation, while high rates enhance penetration through gravels. (4) Stimulation strategy impacts SRV: Multi-cluster perforations show limited effectiveness in enhancing fracture network complexity. In contrast, variable-rate fracturing significantly increases stimulated reservoir volume (SRV) compared to constant-rate methods, as evidenced by microseismic data demonstrating improved interface connectivity and broader fracture coverage. Full article

Every year, a billion tires are discarded worldwide, with only a small percentage being recycled. This leads to significant environmental hazards, such as fire risks and improper disposal. Silty sand also presents technical challenges due to its poor shear strength, susceptibility to erosion, and low permeability. This study explores the incorporation of crumb rubber derived from waste tires into silty sand to enhance its mechanical properties. Crumb rubber particles of varying sizes (3–6 mm, 5–10 mm, and 10–20 mm) were mixed with silty sand at 0%, 3%, 6%, and 9% percentages, respectively. Triaxial compression tests of unconsolidated and consolidated undrained tests with cell pressures of 100, 300, and 500 kPa were conducted. The deviatoric stress, shear stress, and stiffness modulus were investigated. The results revealed that the addition of crumb rubber significantly increased the deviatoric and shear stresses, especially at particle sizes of 5–10 mm, with contents of 3%, 6%, and 9%. Additionally, the stiffness modulus was notably reduced in the mixture containing 6% crumb rubber tire. These findings suggest that incorporating crumb rubber tires into silty sand not only improves silty sand performance but also offers an environmentally sustainable approach to tire waste recycling, making it a viable strategy for silty sand stabilization in construction and geotechnical engineering performance. Full article

In this study, the efficacy of super white cement (SWC) to improve organic soils was researched. For stabilization, 10%, 15%, and 20% proportions of SWC were added to organic soil. After improvement with SWC, Atterberg limit testing, standard Proctor tests, triaxial compression tests, and swelling and compressibility tests were performed on the organic soil. Proctor tests showed that stabilization of organic soil with SWC increased maximum dry density (MDD) and optimum moisture content (OMC) values. After stabilization, the unconfined compressional strength values of the soil increased. This increase continued until the 28th day and had a reducing trend after improvement with SWC, linked to time. In addition to the reaction between SWC and OS, the time-dependent behavior of OS also contributed to this behavior. With the increase in SWC proportions, the cohesion intercept and internal friction angle values rapidly increased until the 56th day. This increase began to reduce after the 56th day. After stabilization, the swelling percentage and compressibility values for the soil reduced. The addition of SWC within organic soil appeared to improve the engineering properties of the soil. Full article

This study investigates the improvement effect and micro-mechanism of guar gum and palm fibers, two eco-friendly materials, on expansive soil. The study uses disintegration tests, unconfined compressive strength tests, triaxial compression tests, and SEM analysis to evaluate the enhancement of mechanical properties. The results show that the guar gum–palm fiber composite significantly improves the compressive and shear strength of expansive soil. The optimal ratio is 2% guar gum, 0.4% palm fiber, and 6 mm palm fiber length. Increasing fiber length initially boosts and then reduces unconfined compressive strength. Guar gum increases unconfined compressive strength by 187.18%, further improved by 20.9% with palm fibers. When fiber length is fixed, increasing palm fiber content increases and then stabilizes peak stress and shear strength (cohesion and internal friction angle), improving by 27.30%, 52.1%, and 12.4%, respectively, compared to soil improved with only guar gum. Micro-analysis reveals that guar gum enhances bonding between soil particles via a gel matrix, improving water stability and mechanical properties, while palm fibers reinforce the soil and inhibit crack propagation. The synergistic effect significantly enhances composite-improved soil performance, offering economic and environmental benefits, and provides insights for expansive soil engineering management. Full article

Using the enzyme-induced carbonate precipitation (EICP) technique to solidify rubber and clay mixtures as lightweight backfill is a feasible way to reduce waste tire impacts and boost rubber recycling in geotech engineering. In this study, a comprehensive laboratory investigation, including triaxial compression, oedometer, permeability, and nuclear magnetic resonance (NMR) tests, was conducted on EICP-reinforced rubber particle solidified clay (hereafter referred to as EICP-RC solidified clay) to evaluate the effects of rubber particle content and size on the mechanical behavior of the improved soil under various solidification conditions and to elucidate the solidification mechanism. The results show that although rubber particles inhibit EICP, they significantly enhance the mechanical properties of the samples. The addition of 5% rubber particles (rubber A) increased cohesion by 11% and the internal friction angle by 18% compared to EICP-treated clay without rubber. Additionally, incorporating smaller-sized tire particles facilitated pore filling, resulting in lower compression and swelling indices and reduced permeability coefficients, making these materials suitable for use behind retaining walls and in embankment construction. Full article

In response to the high-performance requirements of concrete materials under complex triaxial stress states and water-containing environments in marine engineering, this study focuses on water-containing basalt fiber-reinforced concrete (BFRC). Uniaxial compression and splitting tensile tests were conducted on specimens with different fiber contents (0.0%, 0.05%, 0.10%, 0.15%, and 0.20%) to determine the optimal fiber content of 0.1%. The compressive strength of the concrete with this fiber content increased by 13.5% compared to the control group without fiber, reaching 36.90 MPa, while the tensile strength increased by 15.9%, reaching 2.33 MPa. Subsequently, NMR and SEM techniques were employed to analyze the internal pore structure and micro-morphology of BFRC. It was found that an appropriate amount of basalt fiber (content of 0.1%) can optimize the pore structure and form a reticular three-dimensional structure. The pore grading was also improved, with the total porosity decreasing from 7.48% to 7.43%, the proportion of harmless pores increasing from 4.03% to 4.87%, and the proportion of harmful pores decreasing from 1.67% to 1.42%, thereby significantly enhancing the strength of the concrete. Further triaxial compression tests were conducted to investigate the mechanical properties of BFRC under different confining pressures (0, 3, and 6 MPa) and water contents (0%, 1%, 2%, and 4.16%). The results showed that the stress–strain curves primarily underwent four stages: initial crack compaction, elastic deformation, yielding, and failure. In terms of mechanical properties, when the confining pressure increased from 0 MPa to 6 MPa, taking dry sandstone as an example, the peak stress increased by 54.0%, the elastic modulus increased by 15.7%, the peak strain increased by 37.0%, and the peak volumetric strain increased by 80.0%. In contrast, when the water content increased from 0% to 4.16%, taking a confining pressure of 0 MPa as an example, the peak stress decreased by 27.4%, the elastic modulus decreased by 43.2%, the peak strain decreased by 59.3%, and the peak volumetric strain decreased by 106.7%. Regarding failure characteristics, the failure mode shifted from longitudinal splitting under no confining pressure to diagonal shear under confining pressure. Moreover, as the confining pressure increased, the degree of failure became more severe, with more extensive cracks. However, when the water content increased, the failure degree was relatively mild, but it gradually worsened with further increases in water content. Based on the CDP model, a numerical model for simulating the triaxial compression behavior of BFRC was developed. The simulation results exhibited strong consistency with the experimental data, thereby validating the accuracy and applicability of the model. Full article