Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766

Polozov, Igor; Razumov, Nikolay; Masaylo, Dmitriy; Silin, Alexey; Lebedeva, Yuliya; Popovich, Anatoly

doi:10.3390/ma13112630

Open AccessErratum

Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766

¹

Peter the Great St. Petersburg Polytechnic University, Polytechnicheskaya, 29, St. Petersburg 195251, Russia

²

Federal State Unitary Enterprise “All-Russian Scientific Research Institute of Aviation Materials” State Research Center of the Russian Federation, 17 Radio str., Moscow 105005, Russia

^*

Author to whom correspondence should be addressed.

Materials 2020, 13(11), 2630; https://doi.org/10.3390/ma13112630

Submission received: 19 May 2020 / Accepted: 5 June 2020 / Published: 9 June 2020

(This article belongs to the Special Issue Materials, Design and Process Development for Additive Manufacturing)

Download Versions Notes

The authors wish to make the following correction to this paper [1]:

Change in Funding.

The authors wish to change the funding part from:

Funding: This research was supported by Russian Science Foundation grant (project No 19-79-30002).

to

Funding: This research received no external funding.

The authors would like to apologize for any inconvenience caused to the readers by these changes.

References

Polozov, I.; Razumov, N.; Masaylo, D.; Silin, A.; Lebedeva, Y.; Popovich, A. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766. [Google Scholar] [CrossRef] [Green Version]

© 2020 by the authors. Licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution (CC BY) license (http://creativecommons.org/licenses/by/4.0/).

Share and Cite

MDPI and ACS Style

Polozov, I.; Razumov, N.; Masaylo, D.; Silin, A.; Lebedeva, Y.; Popovich, A. Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766. Materials 2020, 13, 2630. https://doi.org/10.3390/ma13112630

AMA Style

Polozov I, Razumov N, Masaylo D, Silin A, Lebedeva Y, Popovich A. Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766. Materials. 2020; 13(11):2630. https://doi.org/10.3390/ma13112630

Chicago/Turabian Style

Polozov, Igor, Nikolay Razumov, Dmitriy Masaylo, Alexey Silin, Yuliya Lebedeva, and Anatoly Popovich. 2020. "Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766" Materials 13, no. 11: 2630. https://doi.org/10.3390/ma13112630

Note that from the first issue of 2016, this journal uses article numbers instead of page numbers. See further details here.

Article Menu

Erratum: Polozov, I., et al. Fabrication of Silicon Carbide Fiber-Reinforced Silicon Carbide Matrix Composites Using Binder Jetting Additive Manufacturing from Irregularly-Shaped and Spherical Powders. Materials 2020, 13, 1766

References

Share and Cite

Article Metrics

Article Access Statistics

Further Information

Guidelines

MDPI Initiatives

Follow MDPI