Nanomaterials, Volume 12, Issue 13 (July-1 2022) – 192 articles

Nanomaterials (NMs) solve specific problems with remarkable results in several industrial and scientific areas. Among NMs, silver nanoparticles (AgNPs) have been extensively employed as drug carriers, medical diagnostics, energy harvesting devices, sensors, lubricants, and bioremediation. Notably, they have shown excellent antimicrobial, anticancer, and antiviral properties in the biomedical field. The literature analysis shows a selective cytotoxic effect on cancer cells compared to healthy cells, making its potential application in cancer treatment evident, increasing the need to study the potential risk of their use to environmental and human health. A large battery of toxicity models, both in vitro and in vivo, have been established to predict the harmful effects of incorporating AgNPs in these numerous areas or those produced due to involuntary exposure. However, these models often report contradictory results due to their lack of standardization, generating controversy and slowing the advances in nanotoxicology research, fundamentally by generalizing the biological response produced by the AgNP formulations. This review summarizes the last ten years’ reports concerning AgNPs’ toxicity in cellular respiratory system models (e.g., mono-culture models, co-cultures, 3D cultures, ex vivo and in vivo). In turn, more complex cellular models represent in a better way the physical and chemical barriers of the body; however, results should be used carefully so as not to be misleading. The main objective of this work is to highlight current models with the highest physiological relevance, identifying the opportunity areas of lung nanotoxicology and contributing to the establishment and strengthening of specific regulations regarding health and the environment. Full article

Nanocomposites of poly (vinylidene fluoride) PVDF with graphene nanoflakes (GNF) were prepared using two different routes. Initially, a mix-melting method was used to prepare composites, and their thermal and mechanical properties were evaluated to choose the better method for future experiment and properties investigation. Then, nanocomposite films were prepared by a simple solution-casting technique using a PVDF/graphene solution. In both cases, the amount of graphene was varied to observe and to compare their thermal and mechanical properties. The addition of graphene to the PVDF matrix resulted in changes in the crystallization and melting behaviors as confirmed by DSC analyses. Increasing the graphene content led to improved thermal stability of the PVDF nanocomposites prepared using both methods. Improvements in mechanical properties by the addition of graphene were also observed. Better performance was observed by the nanocomposites prepared by a mix-melting technique suggesting better dispersion and strong interface bonding between PVDF and graphene particles. Thermal and electrical conductivity were measured and compared. Microstructure and morphology were characterized using FTIR, XRD, and SEM analyses. Full article

The pressure-driven membrane separation processes ultrafiltration (UF) and reverse osmosis (RO) enable the effective purification of wastewater, in particular in combination, allowing organic and inorganic contaminants to be separated from the wastewater. Consequently, this work investigates the suitability of this technology for slaughterhouse wastewater (SWW) recycling. This was investigated by means of laboratory and bench-scale plant membrane experiments, whereby slaughterhouse wastewater (SWW) pre-treated by flotation was first treated with UF and then further purified with RO. Through the process combination UF + RO in the bench scale experiment, a reduction of the parameters total organic carbon (TOC), chemical oxygen demand (COD) of more than 98% and 97% for the parameter total nitrogen (TN) could be achieved. This means that wastewater reuse without product contact can be guaranteed. For direct process water reuse, only the concentration limit for ammonium could not be reached. In addition, scanning electron microscopy (SEM) images and energy dispersive X-ray spectroscopy (EDX) analyses of the RO membrane were carried out before and after the experiment, which did not indicate any scaling effects. Full article

The new research presents highly conductive polymeric membranes with a large surface area to volume ratio of metal oxide nanoparticles that were used to determine atropine sulfate (AT) in commercial dosage forms. In sensing and biosensing applications, the nanomaterials zinc oxide (ZnONPs) and magnesium oxide (MgONPs) were employed as boosting potential electroactive materials. The electroactive atropine phosphotungstate (AT-PT) was created by combining atropine sulfate and phosphotungstic acid (PTA) and mixing it with polymeric polyvinyl chloride (PVC) with the plasticizer o-nitrophenyl octyl ether (o-NPOE). The modified sensors AT-PT-ZnONPs or AT-PT-MgONPs showed excellent selectivity and sensitivity for the measurements of atropine with a linear concentration range of 6.0 × 10⁻⁸ − 1.0 × 10⁻³ and 8.0 × 10⁻⁸ − 1.0 × 10⁻³ mol L⁻¹ with regression equations of E_(mV) = (56 ± 0.5) log [AT] − 294 and E_(mV) = (54 ± 0.5) log [AT] − 422 for AT-PT-NPs or AT-PT-MgONPs sensors, respectively. The AT-PT coated wire sensor, on the other hand, showed a Nernstian response at 4.0 × 10⁻⁶ − 1.0 × 10⁻³ mol L⁻¹ and a regression equation E_(mV) = (52.1 ± 0.2) log [AT] + 198. The methodology-recommended guidelines were used to validate the suggested modified potentiometric systems against various criteria. Full article

In this study, highly-sensitive piezoresistive strain sensors based on gold nanoparticle thin films deposited on a stretchable PDMS substrate by centrifugation were developed to measure arterial pulse waveform. By controlling carbon chain length of surfactants, pH value and particle density of the colloidal solutions, the gauge factors of nanoparticle thin film sensors can be optimized up to 677 in tensile mode and 338 in compressive mode, and the pressure sensitivity up to 350. Low pH and thin nanoparticle films produce positive influences to superior gauge factors. It has been demonstrated that nanoparticle thin film sensors on PDMS substrates were successfully applied to sense arterial pulses in different body positions, including wrist, elbow crease, neck, and chest. Full article

The SF₆/N₂ gas mixture is an alternative gas to SF₆. SF₆/N₂ will decompose and generate nitrogenous characteristic gases, such as NO, NO₂, N₂O, and NF₃, when exposed to long-term partial discharge. The adsorption models of Ti₃C₂T_x (T=O, F, OH) and NO, NO₂, N₂O, NF₃ were constructed, and the most stable adsorption structure was selected in this paper. The electron density and density of states of the adsorption system were further analyzed to study the adsorption behavior, and the sensing performance was evaluated in the end. The results are as follows: four gases could be spontaneously adsorbed on Ti₃C₂T_x, and strong adsorption occurred when surface terminal groups were OH, forming hydrogen or chemical bonds with significant charge transfer. Results show that Ti₃C₂(OH)₂ had a stronger sensing ability than Ti₃C₂F₂ and Ti₃C₂O₂. The conductivity of the Ti₃C₂T_x with different terminal groups was improved after the adsorption of NO and NO₂, showing Ti₃C₂T_x had a good sensing ability for NO and NO₂. It was difficult for the four gases to desorb from the Ti₃C₂(OH)₂ surface, but the adsorption on the Ti₃C₂F₂, Ti₃C₂O₂ surface had a short recovery time at room temperature. Full article

Solid-state batteries (SSBs) have emerged as a potential alternative to conventional Li-ion batteries (LIBs) since they are safer and offer higher energy density. Despite the hype, SSBs are yet to surpass their liquid counterparts in terms of electrochemical performance. This is mainly due to challenges at both the materials and cell integration levels. Various strategies have been devised to address the issue of SSBs. In this review, we have explored the role of graphene-based materials (GBM) in enhancing the electrochemical performance of SSBs. We have covered each individual component of an SSB (electrolyte, cathode, anode, and interface) and highlighted the approaches using GBMs to achieve stable and better performance. The recent literature shows that GBMs impart stability to SSBs by improving Li⁺ ion kinetics in the electrodes, electrolyte and at the interfaces. Furthermore, they improve the mechanical and thermal properties of the polymer and ceramic solid-state electrolytes (SSEs). Overall, the enhancements endowed by GBMs will address the challenges that are stunting the proliferation of SSBs. Full article

Fiber-shaped dye-sensitized solar cells (FDSSCs) with flexibility, weavablity, and wearability have attracted intense scientific interest and development in recent years due to their low cost, simple fabrication, and environmentally friendly operation. Since the Grätzel group used the organic radical 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO) as the redox system in dye-sensitized solar cells (DSSCs) in 2008, TEMPO has been utilized as an electrolyte to further improve power conversion efficiency (PCE) of solar cells. Hence, the TEMPO with high catalyst oxidant characteristics was developed as a hybrid solid-state electrolyte having high conductivity and stability structure by being integrated with a lithium bis(trifluoromethanesulfonyl)imide (Li-TFSI) film for FDSSCs. The optimized 4-Oxo TEMPO (OX) based solid-state FDSSC (SS-FDSSC) showed the PCE of up to 6%, which was improved by 34.2% compared to that of the reference device with 4.47%. The OX-enhanced SS-FDSSCs reduced a series resistance (R_s) resulting in effective electron extraction with improved short-circuit current density (J_SC), while increasing a shunt resistance (R_sh) to prevent the recombination of photo-excited electrons. The result is an improvement in a fill factor (FF) and consequently a higher value for the PCE. Full article

Adjustable lubrication aims to achieve active control of the relative motion of the friction interface, providing a new idea for intelligent operation. A new phenomenon of sudden changes of friction coefficient (COF) in the poly(vinylphosphoric acid) (PVPA) superlubricity system by mixing different lubricants, was found in this study. It was found that anions were the critical factor for the COF change. The change degrees of the COF were investigated by a universal micro tribometer (UMT). A quartz crystal microbalance (QCM)-D was used to analyze the adsorption quantity of anions on the PVPA surface. The hydratability of the PVPA interface was controlled by changing the anionic properties (the amount of charge and structure), thus regulating the COF. The adsorption difference of anions is an important reasoning of how anionic properties can regulate the hydratability. It was analyzed by molecular dynamics simulation. For anions carrying different numbers of charges or double bonds, the adsorption quantity of anions was mainly affected by the adsorption degree on the PVPA surface, while the adsorption quantity of anions with different molecular configuration was synergistically regulated by the adsorption degree and adsorption area of anions on the PVPA surface. This work can be used to develop smart surfaces for applications. Full article

Amorphous silica nanoparticles (ASNP) are present in a variety of products and their biological effects are actively investigated. Although several studies have documented pro-inflammatory effects of ASNP, the possibility that they also modify the response of innate immunity cells to natural activators has not been thoroughly investigated. Here, we study the effects of pyrogenic ASNP on the LPS-dependent activation of human macrophages differentiated from peripheral blood monocytes. In macrophages, 24 h of pre-exposure to non-cytotoxic doses of ASNP markedly inhibited the LPS-dependent induction of pro-inflammatory (TNFα, IL-6) and anti-inflammatory cytokines (IL-10). The inhibitory effect was associated with the suppression of NFκB activation and the increased intracellular sequestration of the TLR4 receptor. The late induction of glutamine synthetase (GS) by LPS was also prevented by pre-exposure to ASNP, while GS silencing did not interfere with cytokine secretion. It is concluded that (i) macrophages exposed to ASNP are less sensitive to LPS-dependent activation and (ii) GS induction by LPS is likely secondary to the stimulation of cytokine secretion. The observed interference with LPS effects may point to a dampening of the acute inflammatory response after exposure to ASNP in humans. Full article

Morphology of support is of fundamental significance to the fabrication of highly efficient catalysts for CO oxidation reaction. Many methods for the construction of supports with specific morphology and structures greatly rely on controlling general physical and chemical synthesis conditions such as temperature or pH. In this paper, we report a facile route to prepare yttria nanosheet using NaCl as template to support platinum nanoparticles exhibiting higher CO oxidation activity than that of the normally prepared Pt/Y₂O₃. With the help of TEM and SEM, we found that Pt NPs evenly distributed on the surface of NaCl modified 2D-nanosheets with smaller size. The combination of XAFS and TEM characterizations demonstrated that the nano-size Pt species with Pt_xO_y structure played an essential role in the conversion of CO and kept steady during the CO oxidation process. Moreover, the Pt nanoparticles supported on the NaCl templated Y₂O₃ nanosheets could be more easily reduced and thus exposed more Pt sites to adsorb CO molecules for CO oxidation according to XPS and DRIFTS results. This work offers a unique and general method for the preparation of potential non-cerium oxide rare earth element oxide supported nanocatalysts. Full article

Considering how important rare earth elements (REEs) are for many different industries, it is important to separate them from other elements. An extractant that binds to REEs inexpensively and selectively even in the presence of interfering ions can be used to develop a useful separation method. This work was designed to recover REEs from spent nickel–metal hydride batteries using ammonium sulfate. The chemical composition of the Ni–MH batteries was examined. The operating leaching conditions of REE extraction from black powder were experimentally optimized. The optimal conditions for the dissolution of approximately 99.98% of REEs and almost all zinc were attained through use of a 300 g/L (NH₄)₂SO₄ concentration after 180 min of leaching time and a 1:3 solid/liquid phase ratio at 120 °C. The kinetic data fit the chemical control model. The separation of total REEs and zinc was conducted under traditional conditions to produce both metal values in marketable forms. The work then shifted to separate cerium as an individual REE through acid baking with HCl, thus leaving pure cerium behind. Full article

Heating has recently been applied as an alternative to electrical stimulation to modulate excitability and to induce neuritogenesis and the expression of neuronal markers; however, a long-term functional differentiation has not been described so far. Here, we present the results obtained by a new approach for scalable thermal stimulation on the behavior of a model of dorsal root ganglion neurons, the F-11 cell line. Initially, we performed experiments of bulk stimulation in an incubator for different time intervals and temperatures, and significant differences in neurite elongation and in electrophysiological properties were observed in cultures exposed at 41.5 °C for 30 min. Thus, we exposed the cultures to the same temperature increase using a near-infrared laser to irradiate a disc of Prussian blue nanoparticles and poly-vinyl alcohol that we had adhered to the outer surface of the petri dish. In irradiated cells, neurites were significantly longer, and the electrophysiological properties (action potential firing frequency and spontaneous activity) were significantly increased compared to the control. These results show for the first time that a targeted thermal stimulation could induce morphological and functional neuronal differentiation and support the future application of this method as a strategy to modify neuronal behavior in vivo. Full article

This study describes the preparation and characterization of eggplant peel extract-loaded electrospun gelatin nanofiber and study of its in vitro release. Results obtained by scanning electron microscopy (SEM) and transmission electronic microscopy (TEM) micrograph revealed that eggplant peel extract-loaded electrospun gelatin nanofiber is in nanometric range with an average diameter 606.7 ± 184.5 and 643.6 ± 186.7 nm for 20 and 33.3 mg mL⁻¹ of extract addition, respectively. Moreover, the incorporation of extract improved morphology by being smooth, homogeneous, and without account formation compared to nanofibers without extract (control). Fourier transform-infrared (FT-IR) spectra indicated that interaction exists between electrospun gelatin nanofiber and eggplant peel extract by hydrogen bond interactions, mainly. Electrospun gelatin nanofibers showed encapsulation efficiency greater than 90% of extract and a maximum release of 95 and 80% for the medium at pH 1.5 and 7.5, respectively. Therefore, the electrospinning technique is a good alternative for the conservation of bioactive compounds present in the eggplant peel through electrospun gelatin nanofiber. Full article

This paper presents the results of a study of the change in the stability of Fe₂O₃/NdFeO₃ nanocomposites when exposed to aggressive media over a long period of time. The main purpose of these studies is to investigate the mechanisms of degradation and corrosion processes occurring in Fe₂O₃/NdFeO₃ nanocomposites, as well as the influence of the phase composition on the properties and degradation resistance. According to the X-ray phase analysis, it was found that the variation of the initial components leads to the formation of mixed composition nanocomposites with different Fe₂O₃/NdFeO₃ phase ratios. During corrosion tests, it was found that the dominance of the NdFeO₃ phase in the composition of nanocomposites leads to a decrease in the degradation and amorphization rate of nanostructures by a factor of 1.5–2 compared to structures in which the Fe₂O₃ phase dominates. Such a difference in the degradation processes indicates the high stability of two-phase composites. Moreover, in the case of an aqueous medium, nanocomposites dominated by the NdFeO₃ phase are practically not subjected to corrosion and deterioration of properties. The results obtained helped to determine the resistance of Fe₂O₃/NdFeO₃ nanocomposites to degradation processes caused by exposure to aggressive media, as well as to determine the mechanisms of property changes in the process of degradation. The results of the study of the absorption capacity of Fe₂O₃/NdFeO₃ nanocomposites in the case of the purification of aqueous media from manganese and arsenic showed that a change in the phase ratio in nanocomposites leads to an increase in the absorption efficiency of pollutants from aqueous media. Full article

Van der Waals heterostructures offer an additional degree of freedom to tailor the electronic structure of two-dimensional materials, especially for the band-gap tuning that leads to various applications such as thermoelectric and optoelectronic conversions. In general, the electronic gap of a given system can be accurately predicted by using first-principles calculations, which is, however, restricted to a small unit cell. Here, we adopt a machine-learning algorithm to propose a physically intuitive descriptor by which the band gap of any heterostructures can be readily obtained, using group III, IV, and V elements as examples of the constituent atoms. The strong predictive power of our approach is demonstrated by high Pearson correlation coefficient for both the training (292 entries) and testing data (33 entries). By utilizing such a descriptor, which contains only four fundamental properties of the constituent atoms, we have rapidly predicted the gaps of 7140 possible heterostructures that agree well with first-principles results for randomly selected candidates. Full article

Vertically aligned carbon nanotubes (VACNT) are manufactured nanomaterials with excellent properties and great potential for numerous applications. Recently, research has intensified toward achieving VACNT synthesis on different planar and non-planar substrates of various natures, mainly dependent on the user-defined application. Indeed, VACNT growth has to be adjusted and optimized according to the substrate nature and shape to reach the requirements for the application envisaged. To date, different substrates have been decorated with VACNT, involving the use of diffusion barrier layers (DBLs) that are often insulating, such as SiO₂ or Al₂O₃. These commonly used DBLs limit the conducting and other vital physico-chemical properties of the final nanomaterial composite. One interesting route to improve the contact resistance of VACNT on a substrate surface and the deficient composite properties is the development of semi-/conducting interlayers. The present review summarizes different methods and techniques for the deposition of suitable conducting interfaces and controlled growth of VACNT on diverse flat and 3-D fibrous substrates. Apart from exhibiting a catalytic efficiency, the DBL can generate a conducting and adhesive interface involving performance enhancements in VACNT composites. The abilities of different conducting interlayers are compared for VACNT growth and subsequent composite properties. A conducting interface is also emphasized for the synthesis of VACNT on carbonaceous substrates in order to produce cost-effective and high-performance nano-engineered carbon composites. Full article

In this work, WS₂ was adopted as a channel material among transition metal dichalcogenides (TMD) materials that have recently been in the spotlight, and the circuit power performance (power consumption, operating frequency) of the monolayer WS₂ field-effect transistor with a double gate structure (DG WS₂-FET) was analyzed. It was confirmed that the effective capacitance, which is circuit power performance, was greatly changed by the extrinsic capacitance components of DG WS₂-FET, and the spacer region length (L_SPC) and dielectric constant (K_SPC) values of the spacer that could affect the extrinsic capacitance components were analyzed to identify the circuit power performance. As a result, when L_SPC is increased by 1.5 nm with the typical spacer material (K_SPC = 7.5), increased operating speed (+4.9%) and reduced active power (–6.8%) are expected. In addition, it is expected that the spacer material improvement by developing the low-k spacer from K_SPC = 7.5 to K_SPC = 2 at typical L_SPC = 8 nm can increase the operating speed by 36.8% while maintaining similar active power consumption. Considering back-end-of-line (BEOL), the change in circuit power performance according to wire length was also analyzed. From these results, it can be seen that reducing the capacitance components of the extrinsic region is very important for improving the circuit power performance of the DG WS₂-FET. Full article

To enhance the utilization efficiency of visible light and reduce the recombination of photogenerated electrons and holes, spindle-shaped TiO₂ photocatalysts with different Ti³⁺ concentrations were fabricated by a simple solvothermal strategy using low-cost, environmentally friendly TiH₂ and H₂O₂ as raw materials and triethanolamine-aqueous as the medium. The photocatalytic activities of the obtained photocatalysts were investigated in the presence of visible light. X-ray diffraction (XRD), Raman spectra, transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FT-IR) spectra were applied to characterize the structure, morphologies, and chemical compositions of as-fabricated Ti³⁺ self-doped TiO₂. The concentration of triethanolamine in the mixed solvent plays a significant role on the crystallinity, morphologies, and photocatalytic activities. The electron–hole separation efficiency was found to increase with the increase in the aspect ratio of as-fabricated Ti³⁺ self-doped TiO₂, which was proved by transient photocurrent response and electrochemical impedance spectroscopy. Full article

Ag-Co films with ultra-high resistivity were prepared on polyimide by magnetron sputtering. The effect of Co content and annealing temperatures on the resistivity and microstructure of Ag-Co films has been thoroughly investigated and the relation between resistivity and microstructure has been discussed. Results show that thicker Ag-Co films without annealing present lower resistivity due to better crystallinity. However, thin Ag-Co films (≤21 nm) annealed at 360 °C present ultra-high film resistivity because of the formation of diffusion pits on the film surface which blocks the transmission of electrons in films to increase film resistivity. Inversely, the resistivity of thick Ag-Co films (≥45 nm) annealed at 360 °C is much less than that annealed at lower than 260 °C owing to no diffusion pits. Furthermore, the addition of Co inhibits the growth of Ag grains and limits the migration of electrons in Ag-Co films further, also resulting in the increase of Ag-Co films’ resistivity. Full article

In this work, we demonstrated the ability of the cyanobacterium Pseudanabaena/Limnothrix sp. to produce ultra-small silver nanoparticlesin the forms of metallic silver (Ag⁰) and silver oxides (Ag_xO_y) via a facile green synthetic process. The biological compounds in the cyanobacterial cellular extract acted both as reducing agents for silver ions and functional stabilizing agents for the silver nanoparticles. Furthermore, the antibacterical activity of the as-synthesized nanoparticles against Gram-negative Escherichia coli and Gram-positive Corynebacterium glutamicum bacterial cells was evaluated. The experimental results revealed a remarkable bactericidal activity of the nanoparticles that was both time-dependent and dose-dependent. In addition to their excellent bactericidal properties, the developed nanoparticles can be used as nanosupports in various environmental, biological, and medical applications. Full article

The resonance property of a magnetic vortex contained within a micron-sized square Py dot was detected using an amplitude-modulated magnetic field excitation technique. We found a significant modulation of the resonant spectra as the external magnetic field changes. The Lorentzian-like spectrum changes from a peak to a dip via a transition of anti-Lorentzian-like spectra. By conducting the micromagnetic simulations, we confirmed that the transition behavior results from the unusual resistance change depending on the vortex core center position. Additionally, the power dependence of the anti-Lorentzian-like spectra revealed a fairly persistent coexistence of peak and dip. Thus, the tunable spectra suggest one way to develop an integratable radiofrequency microcircuits. Full article

Here, the controlled formation of platinum nanoparticles (PtNPs) and silver nanoparticles (AgNPs) using amine-functionalized multivalent ligands are reported. The effects of reaction temperature and ligand multivalency on the growth kinetics, size, and shape of PtNPs and AgNPs were systematically studied by performing a stepwise and a one-step process. PtNPs and AgNPs were prepared in the presence of amine ligands using platinum (II) acetylacetonate and silver (I) acetylacetonate, respectively. The effects of ligands and temperature on the formation of PtNPs were studied using a transmission electron microscope (TEM). For the characterization of AgNPs, additionally, ultraviolet-visible (UV-Vis) absorption was employed. The TEM measurements revealed that PtNPs prepared at different temperatures (160–200 °C, in a stepwise process) are monodispersed and of spherical shape regardless of the ligand multivalency or reaction temperature. In the preparation of PtNPs by the one-step process, ligands affect the shape of the PtNPs, which can be explained by the affinity of the ligands. The TEM and UV-Vis absorption studies on the formation of AgNPs with mono-, di-, and trivalent ligands showed narrower size distributions, while increasing the temperature from 80 °C to 120 °C and with a trivalent ligand in a one-step process. Full article

Exciting Fano resonance can improve the quality factor (Q-factor) and enhance the light energy utilization rate of optical devices. However, due to the large inherent loss of metals and the limitation of phase matching, traditional optical devices based on surface plasmon resonance cannot obtain a larger Q-factor. In this study, a silicon square-hole nano disk (SHND) array device is proposed and studied numerically. The results show that, by breaking the symmetry of the SHND structure and transforming an ideal bound state in the continuum (BIC) with an infinite Q-factor into a quasi-BIC with a finite Q-factor, three Fano resonances can be realized. The calculation results also show that the three Fano resonances with narrow linewidth can produce significant local electric and magnetic field enhancements: the highest Q-factor value reaches 35,837, and the modulation depth of those Fano resonances can reach almost 100%. Considering these properties, the SHND structure realizes multi-Fano resonances with a high Q-factor, narrow line width, large modulation depth and high near-field enhancement, which could provide a new method for applications such as multi-wavelength communications, lasing, and nonlinear optical devices. Full article

The increased requirements in design and manufacturing nanotechnology have favored the development of enhanced composite materials with tailored properties, such as functionally graded (FG) and carbon-based materials, primarily carbon nanotubes (CNTs), and graphene sheets or nanoplatelets, because of their remarkable mechanical properties, electrical conductivity, and high permeability [...] Full article

This work presents the use of encapsulated mini protein 20 mimicking uricase (mp20)-zeolitic imidazolate framework-8 (ZIF-8) as a bioreceptor for the development of a nanozyme-based electrochemical biosensor for uric acid detection. The electrochemical performance of the biofunctionalized mp20@ZIF-8 on the reduced graphene oxide/screen-printed carbon electrode (rGO/SPCE) was investigated by optimizing operating parameters such as pH, deposition potential, and deposition time using a central composite design-response surface methodology (CCD-RSM). The quadratic regression model was developed to correlate the combination of each variable to the oxidation current density as a response. A significant effect on current response was observed under optimized conditions of pH of 7.4 at −0.35 V deposition potential and 56.56 s deposition time, with p < 0.05 for each interacted factor. The obtained coefficient of determination (R²) value of 0.9992 indicated good agreement with the experimental finding. The developed nanozyme biosensor (mp20@ZIF-8/rGO/SPCE) exhibited high selectivity in the presence of the same fold concentration of interfering species with a detection limit of 0.27 μM, over a concentration range of 1 to 34 μM. The practicality of the tailored biosensor in monitoring uric acid in human serum and urine samples was validated with high-performance liquid chromatography (HPLC) and a commercial uric acid meter. Hence, nanozyme-based is a promising platform that offers a rapid, sensitive, selective, and low-cost biosensor for the non-enzymatic detection of uric acid in biological samples. Full article

A memristor is a fundamental electronic device that operates like a biological synapse and is considered as the solution of classical von Neumann computers. Here, a fully printed and flexible memristor is fabricated by depositing a thin film of metal–non-metal (chromium-nitrogen)-doped titanium dioxide (TiO₂). The resulting device exhibited enhanced performance with self-rectifying and forming free bipolar switching behavior. Doping was performed to bring stability in the performance of the memristor by controlling the defects and impurity levels. The forming free memristor exhibited characteristic behavior of bipolar resistive switching with a high on/off ratio (2.5 × 10³), high endurance (500 cycles), long retention time (5 × 10³ s) and low operating voltage (±1 V). Doping the thin film of TiO₂ with metal–non-metal had a significant effect on the switching properties and conduction mechanism as it directly affected the energy bandgap by lowering it from 3.2 eV to 2.76 eV. Doping enhanced the mobility of charge carriers and eased the process of filament formation by suppressing its randomness between electrodes under the applied electric field. Furthermore, metal–non-metal-doped TiO₂ thin film exhibited less switching current and improved non-linearity by controlling the surface defects. Full article

In this paper, hydrophobic luminescent CdSe quantum dots are successfully dispersed in a mixture of styrene and methyl methacrylate through the oleic to methacrylic acid ligand exchange. Further in situ solution polymerization of the quantum dots in a mixture of styrene and methyl methacrylate followed by electrospinning allowed us to prepare luminescence hybrid styrene-co-methyl methacrylate fibers embedded with quantum dots. CdSe@P(S+MMA) hybrid fibers with 27% quantum yield showed excellent moisture, heat and salt resistance with a photoluminescence output below 120 °C. When dry heated, the hybrid fibers of the fluorescence signals decreased with temperature to 79%, 40%, 28%, 20% and 13% at 120 °C, 140 °C, 160 °C, 180 °C and 200 °C, respectively, due the to the chemical degradation of CdSe QDs. Such hybrid fibers show the potential to manufacture wearable moisture- and heat-sensing protective clothing in a 120–200 °C range due to the thermal-induced quenching of quantum dot photoluminescence. Full article

Nanomaterials exhibit intriguing tribological performance and have received particular attention in the lubrication field. However, little research has been found that surveyed the application of nanometer Ni in lithium grease. In this study, nanometer Ni with an average size of 100 nm was synthesized by the direct reduction method and dispersed in lithium grease. The feasibility of nanometer Ni as a grease additive in different lubrication scenarios was evaluated by a four-ball friction tester and a TE77 reciprocating friction tester. The lubrication mechanism was analyzed based on the evaluated physical properties of lithium grease and the characterization of the wear surface. The tribology test results showed the tribological properties of lithium grease were enhanced after introducing nanometer Ni. When the dosage was 0.2 wt%, the friction-reducing and anti-wear properties of point-to-point contact increased by 34.8% and 35.2%, respectively, while those of the point-to-flat contact increased by 28.8% and 38.7%, respectively. Our work not only provides theoretical guidance and practical reference for the utilization of nanometer Ni in grease, but also explains several possible lubrication mechanisms of nanomaterials in grease. Full article