Next Article in Journal
Effect of Carboxylmethyl Cellulose Coating and Osmotic Dehydration on Freeze Drying Kinetics of Apple Slices
Previous Article in Journal
Use of Donkey Milk in Children with Cow’s Milk Protein Allergy
Article Menu

Export Article

Open AccessArticle
Foods 2013, 2(2), 160-169; doi:10.3390/foods2020160

The Development of Expanded Snack Product Made from Pumpkin Flour-Corn Grits: Effect of Extrusion Conditions and Formulations on Physical Characteristics and Microstructure

Foodservice Department, Faculty of Hotel and Tourism Management, Universiti Teknologi MARA (UiTM), Pulau Pinang, 13500 Permatang Pauh, Penang, Malaysia
Institute of Food, Nutrition and Human Health, College of Sciences, Massey University, Private Bag 11222, Palmerston North 4442, New Zealand
Department of Wine, Food and Molecular Biosciences, P.O. Box 84, Lincoln University, Lincoln 7647, Christchurch, New Zealand
These authors contributed equally to this work.
Author to whom correspondence should be addressed.
Received: 30 December 2012 / Revised: 4 April 2013 / Accepted: 3 May 2013 / Published: 14 May 2013
View Full-Text   |   Download PDF [817 KB, uploaded 15 May 2013]   |  


Pumpkin products confer natural sweetness, desirable flavours and β-carotene, a vitamin A precursor when added as ingredients to extruded snacks. Therefore, a potential use for dried pumpkin flour is as an ingredient in ready-to-eat (RTE) snack foods. Growth in this market has driven food manufacturers to produce a variety of new high value snack foods incorporating diverse ingredients to enhance the appearance and nutritional properties of these foods. Ready-to-eat snacks were made by extruding corn grits with 5%, 10%, 15% and 20% of pumpkin flour. Snacks made from 100% corn grits were used as control products for this work. The effect of formulation and screw speeds of 250 rpm and 350 rpm on torque and specific mechanical energy (SME, kWh/kg), physical characteristics (expansion ratio, bulk density, true density and hardness) and the microstructure of the snacks were studied. Increasing the screw speed resulted in a decrease of torque for all formulations. When pumpkin flour was added the specific mechanical energy (SME) decreased by approximately 45%. Increasing the percentage of pumpkin flour at the higher screw speed resulted in a harder texture for the extruded products. X-ray tomography of pumpkin flour-corn grit snacks showed that increased levels of pumpkin flour decreased both the bubble area and bubble size. However, no significant differences (p > 0.05) in bubble wall thickness were measured. By understanding the conditions during extrusion, desirable nutritional characteristics can be incorporated while maximizing expansion to make a product with low bulk density, a fine bubble structure and acceptable organoleptic properties. View Full-Text
Keywords: pumpkin; extrusion; screw speed; feed rate; physical characteristic pumpkin; extrusion; screw speed; feed rate; physical characteristic

Figure 1

This is an open access article distributed under the Creative Commons Attribution License (CC BY 3.0).

Scifeed alert for new publications

Never miss any articles matching your research from any publisher
  • Get alerts for new papers matching your research
  • Find out the new papers from selected authors
  • Updated daily for 49'000+ journals and 6000+ publishers
  • Define your Scifeed now

SciFeed Share & Cite This Article

MDPI and ACS Style

Nor, N.M.; Carr, A.; Hardacre, A.; Brennan, C.S. The Development of Expanded Snack Product Made from Pumpkin Flour-Corn Grits: Effect of Extrusion Conditions and Formulations on Physical Characteristics and Microstructure. Foods 2013, 2, 160-169.

Show more citation formats Show less citations formats

Related Articles

Article Metrics

Article Access Statistics



[Return to top]
Foods EISSN 2304-8158 Published by MDPI AG, Basel, Switzerland RSS E-Mail Table of Contents Alert
Back to Top