1. Introduction
During the practical implementation of several of the core fifth-generation (5G) technologies, there are significant hurdles [
1]. The network service providers in China, for example, recently announced the shutdown of a few 5G base stations (BS) mounted with massive multiple input multiple output (MIMO) [
2]. The increased number of radio frequency (RF) chains necessitates higher hardware costs and higher energy consumption. To meet the growing traffic demands, cell size must be shrunken. This necessitates an increasing number of BSs or access points (AP). This raises the expense of maintenance while also causing practical concerns, such as interference and backhaul management. Exploiting higher frequency bands causes considerable propagation losses, necessitating more complicated signal processing.
Following the completion of the standardization and commercialization of 5G networks, wireless researchers have begun looking for new technologies to support sixth-generation (6G) networks. Since they reconfigure the environment with nearly passive, low-cost elements, reconfigurable intelligent surfaces (RIS) or intelligent reflecting surfaces (IRS) have been identified as viable components for next-generation networks. The RIS system uses abundant low-cost, passive reflecting elements mounted on a planar surface to regulate the amplitude and phase of incident signals [
3,
4]. Active RF chains are not required for RIS, and nearly passive reflecting elements are required. When compared to massive MIMO, the hardware cost and energy consumption are significantly lower. They do not cause noise amplification or self-interference in the way that full duplex transmission does. As a result, it is more appealing than half-duplex relays. RIS can be readily installed on walls, billboards, automobiles, lampposts, and so on. With the help of RIS, cell coverage and network throughput can be greatly boosted.
The number of wirelessly connected devices, as well as the range of wireless services available, such as the internet of everything (IoE), virtual reality (VR), augmented reality (AR), and so on, is rapidly increasing. As a result, next-generation multiple access strategies should be capable of serving a high number of users with additional resources, while maintaining a low level of complexity [
5,
6]. While permitting a certain degree of multiple access interference at the receivers, non-orthogonal multiple access (NOMA) boosts spectral efficiency and facilitates massive connectivity [
7]. In NOMA, the signals pertaining to several users are superimposed in the power domain to more effectively utilize the spectrum. NOMA is classified into two types: fixed and ordered NOMA. In ordered NOMA, the decoding order is determined based on the channel gain of the users, as opposed to fixed NOMA, where the decoding order is predetermined. Because of its appealing qualities, RIS can be combined with other cutting-edge technologies such as NOMA, physical layer security, simultaneous wireless information and power transfer (SWIPT), cognitive radios, autonomous cars, and unmanned aerial vehicles (UAV)-assisted communication, etc. [
8,
9,
10]. The integration of power-domain NOMA with RIS can increase its spectral efficiency and massive connectivity. The symbols used in this work are listed in Nomenclature.
The order in which the remaining manuscript is arranged is as follows:
Section 2 lists the works connected to RIS and NOMA. The closed-form outage probability expressions for blind-RIS-smart reflector (SR)-NOMA uplink and blind-RIS-AP-NOMA uplink are derived in
Section 3. The optimum powers to allocate for maximizing uplink sum capacity are detailed in
Section 4. In
Section 5, Monte-Carlo simulations are performed to verify the obtained analytical expressions.
Section 6 wraps up the work by considering future works.
2. Related Work
In [
11], the RIS-assisted millimetre wave (mmWave) multi-user system’s uplink is examined. By jointly optimizing RIS phase shifts, analog-to-digital converter (ADC) quantization bits, and a beamforming selection matrix under the hardware constraints, the attainable sum capacity is increased. A block coordinated descent (BCD)-based technique is suggested to solve this non-convex problem. It is shown that the proposed BCD algorithm works better than cutting-edge methods. To increase spectrum efficiency, a multi-user uplink with RIS support is recommended in [
12]. In this work, a virtual constellation is built using RIS to transmit data from an additional user. By taking into account two users, the analytical average bit error rate (ABER) expressions are obtained.
For cost- and power-effective coverage extension, a hybrid transmission strategy combining RIS and decode-and-forward (DF) relays is recommended in [
13]. Simulations demonstrate that when used in conjunction rather than as competing technologies, RIS and DF relaying significantly improve rate and error performance. An RIS-aided DF cooperative relaying with energy harvesting is presented in [
14]. The effect of spatial correlation between RIS elements is also investigated. In terms of energy harvesting capability and outage probability, the proposed system is analyzed. Finally, index modulation (IM) is added to the idea of joint RIS and DF relaying. For indoor and outdoor environments and various frequency bands, the benefits of RIS deployment are examined in [
15]. For both single- and multiple-RIS, the system is tested. It has been demonstrated that RIS-assisted systems greatly enhance achievable rates and error performance for indoor and outdoor environments, as well as different operating frequencies.
For orthogonal frequency division multiplexing (OFDM)-based NOMA, a low-complexity user selection and power allocation mechanism is presented in [
16]. Users who do not meet the derived criterion are removed. The expressions for closed-form optimal power allocation are derived to maximize the weighted sum capacity of users. The results reveal that the suggested system outperforms the optimal exhaustive user search technique, while being significantly less complex. In [
17], NOMA-aided mmWave networks are presented, which can suit the needs of users in a variety of applications. For user association, the Lagrange dual decomposition approach is employed, while power and subcarrier allocation are handled using semi-supervised learning and deep neural networks. The proposed method enhances energy efficiency while meeting the quality of service (QoS), power budget, and interference limitations constraints.
The uplink and downlink multiple user power domain NOMA is presented in [
18], where it is assumed that the fading links of each user follow distinct distributions, such as Rayleigh, Rician, Nakagami-
, Nakagami-
,
, and
. Closed-form outage probability expressions are developed for both uplink and downlink, assuming both statistical channel state information and instantaneous channel-based ordering. The simulation results are finally presented to verify the analytical expressions. NOMA can be utilized in land mobile satellite communications to improve coverage and link reliability [
19]. Two terrestrial user nodes are used to execute the NOMA uplink, while a satellite is used to do successive interference cancellation (SIC) or joint decoding. The shadowed Rician fading channel is used to develop the closed-form outage probability expressions. Monte-Carlo simulations are performed to validate the closed-form expressions.
Downlink NOMA’s energy efficiency and fairness are maximized by optimizing subcarrier and power allocation jointly [
20]. To accomplish this, a novel greedy subcarrier allocation approach with minimal complexity and fast convergence is proposed. NOMA and cognitive radio (CR) are powerful solutions that address wireless communication’s spectrum scarcity issue. NOMA and CR are integrated in [
21] to improve spectrum efficiency. For a two-user case, the closed-form outage probability expressions are constructed. It is also proven that fairness between two users is realized through proper power factor allocation. NOMA does not surpass orthogonal multiple access (OMA) in terms of spectral efficiency gain when the channel gains of various users are not significantly different [
22]. In these circumstances, classic OMA is preferable. In NOMA, fairness among users can be attained through effective power allocation. However, increasing the rate of weaker users may result in a decrease in the rate of stronger users. The addition of RIS to NOMA can improve its performance by enabling stronger combined channels.
The effects of coherent and random phase shifting on the performance of RIS-aided NOMA are investigated in [
23]. Analytical and simulation results reveal the trade-off between complexity and reliability. To improve reception reliability, a low-complexity phase selection approach is also presented. In [
24], multiple RIS are used in NOMA to increase the quality of each user’s received signal. Based on the availability of a line-of-sight (LoS) between the BS and the user, the outage probability expressions are derived. For high signal-to-noise-ratio (SNR) regimes, the upper and lower bounds of outage probability expressions are derived. It is proven that the diversity order is not degraded when using a discrete phase shifter. It is also proven that RIS with a three-bit discrete phase shifter achieves near-optimal outage performance. The simulation results further demonstrate that RIS outperforms full duplex DF relays.
In [
25], the outage probability of RIS-assisted NOMA downlink transmission is examined for two users. RIS is used here between the source and the users. It has been shown that the introduction of RIS increases the performance of the far user. Analysis is also done on the impact that the number of RIS elements, power factor allocation, desired rates, and SNR have on the probability of an outage. Fairness among users is ensured by the implementation of RIS.
In [
22], the joint optimization of transmit beamforming at the BS and phase shifts at the RIS are solved by block coordinated descent and semi-definite relaxation techniques to improve the user fairness in a downlink scenario of RIS-assisted NOMA system. Depending on the channel strength, the users are ordered. It is shown that the suggested RIS-assisted NOMA outperforms the traditional NOMA and traditional OMA with and without RIS in terms of the downlink sum capacity. It employs a low-resolution phase shifter with a performance that is nearly identical to that of an ideal RIS with an infinite resolution phase shifter. Here, the outage probability of ordered users is not investigated. It is noted that even for more passive controllable reflecting elements, the improvements in sum capacity are not appreciably greater. The authors intended to increase user fairness in this case. As a result, even with higher SNR, the sum capacity remains nearly constant. In this study, an LoS is assumed to exist between the BS and the RIS, and the BS-RIS channel is modeled using the Rician distribution. Rayleigh distribution is used to model the RIS-users channel since it is expected that there is a non-line-of-sight (NLoS) between the RIS and the users. The LoS assumption between BS and RIS is not realistic in many cases. The system has not been analyzed for RIS as an AP setup.
In [
26], the performance of the cell edge user device is improved by employing IRS-assisted NOMA in both the uplink and the downlink. In this paper, a blind-RIS system is proposed for the uplink scenario of both users in a NOMA system. For each case, closed-form outage probability and Ergodic rate expressions are derived. The number of RIS elements appears to have an effect on the diversity order. Furthermore, the RIS-assisted system outperforms the full duplex DF relay system. In [
27], it is proven that RIS-aided mmWave NOMA in the downlink scenario outperforms mmWave NOMA without RIS. A downlink IRS-aided system over fading channels is considered in which two users are served by different multiple access techniques, namely, NOMA, time division multiple access (TDMA) and frequency division multiple access (FDMA) system in [
28]. A success convex approximation method is framed for the joint optimization of phase shift and resource allocation in solving average sum rate maximization. It is observed that the focus is mainly on the sum rate maximization and error performance of an RIS-assisted downlink NOMA system with and without the assistance of intelligent RIS.
RIS is an excellent option for improving the performance of vehicle-to-everything (V2X) applications. In [
29], it is proven that RIS improves QoS demands for vehicle-to-infrastructure (V2I) and vehicle-to-vehicle (V2I) communications, assuming slowly varying channels. However, the nature of V2X channels is rapidly changing. Recently, the concept of blind-RIS was introduced in [
30]. It has been proven that blind-RIS systems have the advantage of improving SNR by
times at the user end. In blind-RIS, low-cost and passive reflector elements are used for transmission without RF processing. This is more suitable for the uplink process. The following research gaps have been identified from the related work:
The majority of the research assumes intelligent RIS, where the BS-RIS and RIS-users’ channels are known in advance at the RIS. Each RIS element in these models is supposed to pre- and post-cancel the phase distortions brought on by the related channels. The channels are rapidly varying in applications such as V2X. It is quite difficult to gather precise channel information for every user, especially when there are many users and reflecting elements;
The majority of classic works presuppose the deployment of RIS between the transmitter and receiver. The received signal at the RIS may be quite weak when it is far from the transmitter. RIS may not therefore provide the anticipated benefits. The majority of studies examined the sum capacity and outage probability for RIS when configured as an SR. These models might not be realistic in all scenarios;
Further, it is also noted that outage analysis and optimal power allocation for near user and far user of the uplink NOMA system with RIS have not been addressed.
In this paper, the concept of blind-RIS is used for the uplink process, especially in the NOMA system. Motivated by these observations, the technical contributions of this paper are listed below:
Two different system models are proposed for the blind-RIS-assisted uplink NOMA system:
RIS is modeled as a smart reflector (SR) for the near and far users of the uplink NOMA system and it is termed as blind-RIS-SR-NOMA.
RIS is modeled as an access point (AP) for the near and far users of the uplink NOMA system and it is termed as blind-RIS-AP-NOMA.
The optimization problem is formulated to allocate optimal powers at both near and far users to maximize the sum rate of the proposed uplink NOMA systems. Closed-form expressions for optimal power allocation are also obtained by solving the optimization problem;
Extensive Monte-Carlo simulations are performed to corroborate the closed-form expressions that have been derived. The analytical and simulation curves are nearly identical, indicating that the obtained expressions are accurate.
4. Optimal Power Allocation for Uplink Sum Capacity Maximization
The uplink sum capacity is given by
where
and
are the capacity (b/s/Hz) achieved by user 1 and user 2, respectively.
Simplifying (27) results in
Substituting
in (28) gives
To maximize the sum capacity, the power fractions allocated to users 1 and 2 must be optimized. The users should be able to meet the expected QoS requirements without experiencing an outage, and the sum of the power fractions should equal 1. The following optimization problem is formulated in order to identify the feasible region for both users:
From (29), it is clear that
is a monotonically increasing function of
. When
,
becomes
. For
,
reaches
. For maximum uplink capacity,
. This may not satisfy the QoS demand of user 2. The optimization problem formulated in (30) for optimal power allocation to user 1 and user 2 is non-convex in nature. Alternatively, an analytical method is used to identify the feasibility region. Solving (17) for
, the feasible region for user 1 can be obtained.
The detailed derivation of (31) is highlighted in
Appendix F. Similarly, solving (20) for
gives a feasible region for user 2.
The detailed derivation of (32) is highlighted in
Appendix G. By combining the conditions (31) and (32),
The above equation can be written as
Simplifying (34) for
results in
The simplification of (34) is given in
Appendix H. The condition in (35) is the minimum SNR required to meet the QoS constraints of both the users. The optimal power to be allocated for user 1 is the maximum value of
The remaining power is allocated to user 2
5. Results and Discussion
In this section, Monte-Carlo simulations are used to substantiate the outage probability and sum capacity performances of the proposed blind-RIS-NOMA uplink. The simulations are repeated for
channel realizations and the average results are presented. The simulation parameters are listed in
Table 1.
For the blind-RIS-assisted NOMA uplink, the closed-form probability of outage expressions is developed in this work. The related works have emphasized that NOMA does not necessarily outperform OMA. RIS is introduced to enhance the performance of conventional NOMA. Most classic works take an ideal RIS with an infinite resolution phase shifter into consideration. A low-resolution phase shifter RIS is taken into consideration in several works. Here, we sought to demonstrate that even a blind-RIS will have a considerable impact on the effectiveness of uplink outages and sum capacity. For a classic NOMA uplink, the probability of outage expressions is derived in [
18].
The probability of outage expressions for user 1 of the traditional NOMA system is given by [
18]
where
and
are the average channel gains of user 1 and user 2 of a traditional NOMA system. The probability of outage expression for user 2 of a traditional NOMA system is given by [
18]
Hence, the proposed model is compared to the classic NOMA discussed in [
18].
The outage performance of the proposed blind-RIS-SR-NOMA and traditional NOMA is shown in
Figure 3. The power fractions assigned to users 1 and 2 are 0.9 and 0.1, respectively. The number of RIS elements is 32. Due to higher channel gain and more power allocation for user 1, the outage probability of user 1 of traditional NOMA is better than user 2. As per (38), a larger
makes larger
. This results in a lower outage probability compared to user 2. The introduction of blind-RIS elements in the environment increases the array gain, thereby decreasing the outage probability. RIS adds
channel paths to create stronger combined channels. In accordance with (14) and (21),
is introduced to the probability of outage expressions for the RIS-assisted NOMA system. Higher
and
make
in (14) higher. As a result, user 1 of the proposed system is less likely to experience an outage than in the conventional NOMA system. Similarly,
is introduced into the denominator of
of (21). When compared to a traditional NOMA system, a higher
introduces a significant reduction in the outage probability of user 2. At the SNR of 10 dB, user 1′s outage probability in the blind-RIS-SR-NOMA and traditional NOMA is 0.0224 and 0.0432, respectively. User 2’s outage probability in the blind-RIS-SR-NOMA and traditional NOMA is 0.0532 and 0.6558, respectively, for 10 dB SNR. A drastic reduction in outage probability is observed for user 2 when blind-RIS elements are introduced.
The outage analysis is repeated in
Figure 4 by keeping everything the same as in
Figure 3 except the power factors. Users 1 and 2 have been given power fractions of 0.7 and 0.3, respectively. User 1’s outage probability in the blind-RIS-SR-NOMA and traditional NOMA is 0.0798 and 0.1049, respectively, for 10 dB SNR. User 2’s outage probability in the blind-RIS-SR-NOMA and traditional NOMA is 0.0901 and 0.3767, respectively, for 10 dB SNR. It has been noted that the possibility of an outage for both systems has increased as a result of the reduction in power allocated to user 1. The probability of an outage for both systems is decreased by the increased power factor allocation for user 2.
For various choices of
, the outage probability of user 1 in the blind-RIS-SR-NOMA uplink is shown in
Figure 5. User 1 of blind-RIS-SR-NOMA has a lower outage probability than user 2 due to the higher channel gain and greater power allocation. The probability of an outage decreases as the number of reflecting elements grows. The outage probabilities of the proposed blind-RIS system are 0.0219, 0.0221, 0.0224, 0.0231, and 0.0244, with the number of elements 512, 256, 128, 64, and 32 at 4 dB SNR. At low SNR, it is observed that there is a gap between the theoretical and simulation curves, due to the assumptions made in (4) and (5) for mathematical tractability. However, the theoretical and simulation curves are nearly identical for higher values of
. For various choices of
, the outage probability of user 2 of the blind-RIS-SR-NOMA uplink is shown in
Figure 6. The probability of an outage falls as the number of reflecting elements grows. The outage probability of a blind-RIS system is 0.0297, 0.0375, 0.053, 0.0833, and 0.1409 with
, at 4 dB SNR. For higher values of
, the analytical and simulation curves are found to be very similar.
According to the configuration of the simulation, user 1 has a stronger channel than user 2. The capacity of user 2 is reduced as a result of improper random power allocation. The sum capacity is finally reduced as a result. In the proposed work, the power factors are optimally chosen with the objective of maximizing the sum capacity while also satisfying the minimum rate requirements of each individual user. For various values of
, the sum capacity (b/s/Hz) of the blind-RIS-SR-NOMA uplink is shown in
Figure 7. It has been observed that increasing
increases the sum capacity regardless of optimal or sub-optimal power allocations. To validate the performance of optimal power allocation, the following sub-optimal power allocation is used for comparison:
The sum capacity is maximized when optimal powers are allocated as per (36) and (37), compared to sub-optimal power allocations as per (40) and (41). The sum capacity of the optimal and sub-optimal power allocations for = 32 and 20 dB SNR are 13.21 b/s/Hz and 12.71 b/s/Hz, respectively. Other values of show nearly identical gains.
In
Figure 8, the outage performance of the proposed blind-RIS-AP-NOMA and traditional NOMA is shown. The parameters used in this simulation are similar to those in
Figure 3. User 1 of the blind-RIS-AP-NOMA has a lower outage probability than user 2 due to the higher channel gain and greater power allocation. The presence of RIS elements in the environment boosts array gain, lowering the probability of an outage. Blind-RIS-AP-NOMA achieves nearly identical results as blind-RIS-SR-NOMA when compared to the traditional NOMA system. For various choices of
, the outage probability of user 1 of the blind-RIS-AP-NOMA uplink is compared in
Figure 9.
Figure 9’s explanation is identical to that of
Figure 5. In
Figure 10, the outage probability of user 2 of the blind-RIS-AP-NOMA uplink is shown for various values of
.
The proposed blind-RIS-AP-NOMA uplink’s sum capacity (b/s/Hz) is shown in
Figure 11, for various values of
. It has been observed that raising
increases the sum capacity regardless of whether power allocations are optimal or sub-optimal. When optimal powers are allocated, as per (36) and (37), against sub-optimal power allocations, as per (40) and (41), the sum capacity is increased. For
= 32 and 20 dB SNR, the sum capacities of the optimal and sub-optimal power allocations are 13.11 b/s/Hz and 12.64 b/s/Hz, respectively. Other
values yield essentially equal results.
For optimal and sub-optimal power allocations, the sum capacities (b/s/Hz) of NOMA, blind-RIS-SR-NOMA, and blind-RIS-AP-NOMA are compared in
Figure 12. For all systems, the sum capacity of the optimal power allocation is greater than that of the sub-optimal power allocation. The blind-RIS-AP-NOMA system’s capacity is nearly identical to that of the blind-RIS-SR-NOMA system. For 32 RIS elements and 20 dB SNR, the sum capacity of the optimal power assigned blind-RIS-SR-NOMA, blind-RIS-AP-NOMA, and traditional NOMA is 13.21 b/s/Hz, 13.11 b/s/Hz, and 8.13 b/s/Hz, respectively. In comparison to the traditional NOMA system, this represents a
38% increase in sum capacity. The sum capacity of the optimal and sub-optimal power assigned blind-RIS-SR-NOMA is 14.12 b/s/Hz and 13.64 b/s/Hz, respectively, for 64 RIS elements and 20 dB SNR. The sum capacity for the optimal power allocation is
3.4% higher than for the sub-optimal power allocation. The sum capacity of optimal power allotted blind-RIS-SR-NOMA is improved by
6.44% by increasing
from 32 to 64. The number of reflecting elements can be increased to further improve the results.