1. Introduction
Silicone/polyorganosiloxane polymers are the basis (film-forming) for the production of heat-resistant paint and varnish materials, namely organo-soluble enamels and powder paints [
1]. It is revealed that the duration of the protective life of silicone coatings at high temperatures is determined by a combination of a large number of factors, such as: the type of pigment, its dispersion in the coating [
2], supramolecular structure (the presence and size of domain structures of polyorganosiloxanes in the coating), and the type of organosilicon polymers used [
3,
4]. The dispersion of pigments included in silicone enamels is the most important characteristic that determines the properties of coatings. For all investigated silicone composite materials (paints, plastics, and rubber), the following rule is applied: “the maximum of the protective and mechanical properties of the composites corresponds to the maximum dispersion of solid-phase pigments and fillers in the polyorganosiloxane matrix”. Introduction of aluminum nanoparticles, titanium dioxide, etc. to silicone material allows us to obtain more corrosion-resistant coatings [
5]. In addition, silicone enamels require a very narrow technological range of coating thickness, due to the fact that with a small coating thickness, a long protective life of the painted steel surface is not provided. Additionally, when the recommended thickness is exceeded, the coating cracks (due to a catastrophic increase in internal stresses, with a temperature drop of several hundred degrees Celsius). Therefore, for silicone enamels, a very urgent issue is to increase their protective resource (when maintaining small thicknesses) what can be achieved by obtaining coatings with maximum pigment dispersion in a polyorganosiloxane matrix. The work of a number of authors shows an increase in the dispersion of pigments in coatings in the presence of surfactants [
6].
In silicone paint and varnish materials, substances of polyester (PEG) and alkyd nature are used as surfactants [
7,
8]. However, the oxidation of PEG in seawater causes a significant reduction in the service life of the silicone coating. In [
9], the effect of a new polyoxazoline (POS) additive on the properties of silicone coatings was investigated. It is shown that the introduction of POS makes it possible to obtain coatings with good anti-adhesive properties, despite the greater surface roughness and less compatibility with silicone polymer. It was shown in [
10] that the introduction of 2-benzimidazolyl ethantiol into silicone enamel causes the formation of a highly effective antifouling coating.
The study [
11] proves that the introduction of nanosilicon (SiO
2) containing benzotriazole into polydimethylsiloxane makes it possible to obtain a self-healing coating. These coatings demonstrate increased protection of carbon steel from corrosion. An interesting study is presented in [
12], showing that the introduction of an additive (adhesion enhancer) into a silicone composite can significantly increase its mechanical properties. Moreover, the high adhesive characteristics of the composite demonstrate good stability both when used for several hours and during many attachment/disconnection cycles. The study [
13] showed that the introduction of the amino-containing product A-39 into the polyorganosiloxane compositions causes the formation of smaller supramolecular structures with a denser packaging. As a result, the coatings obtained are characterized by a longer protective resource. The introduction of surfactants into a composite based on polymethylsiloxane resin makes it possible to obtain protective coatings with greater pigment dispersion in the polymer matrix [
14]. The coatings obtained in this case have a more ordered supramolecular structure and improved protective characteristics. The world scientific literature reports on the development of silicone composites and paints, using the following additives: aniline oligomer [
15], 3-aminopropyltriethoxysilane [
16], erucamide [
17], melamine [
18], polyamidoamine [
19], amines of the amiture/ancamide series [
20], and polyimides [
21].
Therefore, the use of nitrogen-containing additives as surfactants to improve the dispersion of pigment in silicone enamels seems quite promising. Due to the deteriorating economic and environmental situation in the world, it becomes urgent to develop cheap additives obtained from chemical waste. As an additive in the study, an original industrial product obtained from oil refining waste—AS-1 was used, the synthesis of this product was carried out in the laboratory of the M. Kozybayev NKU [
22]. In addition, to compare the assessment of the effect of AS-1 on pigment dispersion with effect of industrial additives produced on an industrial scale, the study used additional additives: “Telaz D Dispersant” and PEPA.
2. Materials and Methods
2.1. Materials
Polyphenylsiloxane varnish (hereinafter referred to as PPhS) was used as a polymer, the mass fraction of non-volatile substances is 17%; manufacturer: Spektr company, Russia. Toluene was used as a solvent (density 0.866 g/cm3 (at 20 °C); toluene content 99.80%; mass fraction of non-aromatic hydrocarbons 0.1%; manufacturer: Slavneft, Russia. The pigment used was aluminum pigment, PAP-2 grades; the content of active aluminum 97%; the content of iron 0.3%; the content of fat additives 2.5%, manufacturer: SUAL-PM, Russia.
As nitrogen-containing surfactants, we used:
- (1)
The original industrial product obtained from oil refining waste—a mixture of primary and secondary amines AS-1 (molecular weight 250 a.m.u.; amine number (mg HCl/g) 30) was synthesized by our laboratory [
22].
- (2)
The technical product of condensation of vegetable oils with diamines under the trademark “Telaz D Dispersant” (molecular weight 2121 a.m.u.; amine number (mg HCI/g) 32) manufacturer Avtokoninvest, Russia.
- (3)
A technical product, a mixture of high-molecular PEPA amines (molecular weight 4950 a.m.u.; amine number (mg HCI/g) 31), manufacturer JSC Uralkhimplast, Russia.
2.2. Computer-Optical Microscopy of the Dispersing Effect of Surfactants in Suspensions
To assess the effect of surfactants and solvent on the dispersion of pigment in the coating, it is necessary at first to evaluate their effect on the size of pigment particles in the suspensions “pigment-polymer-solvent“. This issue is quite complex and has various solutions: atomic force microscopy [
23] of electrophoretic light scattering (ELS) [
24], ultrasound research methods [
25], and fluorescent and dark-field microscopy [
26]. However, from a practical standpoint, the most effective method is the method of computer-optical microscopy [
27]. Based on the above, we used a complex of computer-optical microscopy to assess the dispersion of the pigment.
To assess the effect of surfactants on the dispersion of the pigment in suspensions “aluminum pigment-toluene-PPhS”, the method of computer-optical microscopy was used. We used an installation consisting of a Pentium III personal computer, a CARL ZEISS 451422 microscope, and a USB camera. A special computer program, DSS (differential distribution spectrum), was developed for the installation of computer-optical microscopy. This program allowed us to process suspensions on the base of obtained microscope images. At the same time, the program determines the number of pigment particles (per unit area) and their geometric parameters (linear dimensions and area). The program calculates the content of various fractions of pigment particles in suspensions. Calibration of the installation on standardized objects showed that the measurement error does not exceed 5–6% (rel.). The duration of the analysis of one sample (from photographing to issuing the results) is 3–4 min.
2.3. Experimental Design
To plan the experiment (due to the large number of surfactant and solvent concentrations studied), the Taguchi method was used. The Taguchi method makes it possible to find the best combination of initial components for obtaining polymer composites with the necessary parameters [
28,
29]. In our case, it is necessary to obtain polyorganosiloxane enamel with maximum pigment dispersion in suspensions “aluminum pigment-toluene-PPhS”.
During the research, compositions were used in which were varied:
- (1)
The content of surfactants (hereinafter CS) from 0 to 0.5 g/dm3;
- (2)
The solvent content (hereinafter referred to as SC) from 10 to 50% (by weight of the composition).
Table 1 shows the factors under consideration and their corresponding levels [
29].
2.3.1. Method of Preparation of Suspensions for Computer-Optical Microscopy
- (1)
A total of 8.65 g of PPhS varnish were poured into a sealed reactor (volume (0.2 ± 0.01) dm3, filling factor 0.60).
- (2)
Toluene was added to the PPhS varnish. The SC ranged from 10 to 50%.
- (3)
Surfactant (CS), previously dissolved in toluene, was introduced in the specified quantities.
- (4)
An aluminum pigment of 0.35 g (3.5% of the mass of the mixture) was added.
- (5)
The reactor lid was hermetically closed, and the mixing device was turned on (an impeller agitator, speed of rotation 300min−1).
- (6)
After 30 min of mixing, the agitator was turned off and the lid was opened.
- (7)
Then, the suspension samples were placed on a slide using a pipette (a drop volume of 20 mL), fixed with a cover glass and held for 5 min under a static load of 10 g/cm2.
- (8)
After exposure for 5 min, the sample was subjected to computer-micro-optical scanning.
2.3.2. The Method of Analysis of Suspensions
When performing the analyses, the multiplicity of magnification of the computer-optical system was set constant. The dispersion of the pigment was controlled by changes in the specific number of pigment particles on a fixed area (S0 = 0.04 mm2) of the processed image (SNP) and the average particle diameter of the pigment (APDP). The above characteristics were determined by the results of the analysis of five parallel samples.
2.3.3. Planning an Experiment Using the Taguchi Method
In this study, the L9 matrix was used, and the signal-to-noise ratio (S/N) was used as a characteristic of the selection quality. In the Taguchi method, three different functions are used to find the signal-to-noise ratio (S/N): “the-smaller-the-better” (SB), “the-nominal-the-best” (NB), or “the-larger-the-better” (LB). To minimize APDP, we used the SB function (Equation (1)), and to maximize SNP, we used the LB function (Equation (2)) [
29].
where
n is the number of test runs and
y is the measured dispersion values of APDP or SNP.
The
S/NS ratios for APDP were calculated according to Equation (1), as shown in
Table 2.
The
S/NL ratios for SNP were calculated according to Equation (2), as shown in
Table 3.
2.4. Methodology for Checking the Quality of Coatings
The corrosion rate was determined in the Caspian Sea water according to ISO 11845:2020(en) standard on steel plates 65 cm × 25 cm × 0.1 cm (length × width × thickness). The coating was applied to the plates by the filling method and kept for 8 h at a temperature of 350 ± 5 °C. The test time was 96 h. The corrosion rate was determined by gravimetric method (weighing the plates before and after exposure in the water of the Caspian Sea). Each sample was weighed at least 5 times. The results show the average values.
The appearance of the coatings was evaluated on steel plates measuring 15 cm × 7 cm (length × width) in natural (sunlight) light. The coating was applied to the plates by the filling method and kept for 8 h at a temperature of 350 ± 5 °C. All samples were examined at least 5 times.
4. Discussion
The improvement of pigment dispersion is recorded for all the studied additives. The maximum dispersion of the pigment was recorded at CS 0.25 g/dm3 for all the studied surfactants. For a PEPA at CS 0.25 g/dm3, the APDP decrease was 46% (from 26 to 14 microns), and the SNP increased by 2 times (from 258 to 550 pcs). In similar conditions for AS-1, the decrease in APDP was 31%, and the SNP increased by 1.7 times. For Telaz, the decrease in APDP was 38.5%, and the SNP increased by 1.9 times. Therefore, the three studied additives according to the quantitative indicators of the dispersing effect (APDP and SNP) can be arranged in a row (followed in descending order of activity): PEPA > Telaz > AS-1. The most effective surfactant dispersant for polyphenylsiloxane enamel is PEPA.
As the solvent content in the composition (SC) increases, computer-optical microscopy revealed a decrease in the dispersing effect of surfactants, expressed in an increase in the diameter of pigment particles (APDP) and a decrease in their number (SNP) (
Figure 1,
Figure 2 and
Figure 3). However, the presence of additives in the enamel allows us to minimize the harmful effect of the solvent. With an increase in the solvent content (SC) from 10 to 50% in suspensions (without surfactants), APDP increases from 26 to 36 microns (by 38.5%), and SNP decreased from 258 to 208 pcs. (by 20%). With the introduction of additives in the composition, it is possible to stabilize the dispersing effect of surfactants. Thus, PEPA at a concentration of 0.25 g/dm
3 with an increase in SC from 10 to 50% stabilizes the APDP value at a level of up to 22–24 microns (without surfactants up to 36 microns), and SNP decreases to 400 pcs. (without surfactants up to 208 pcs.). Therefore, even in highly dilute solutions of polyphenylsiloxanes, it is possible to stabilize the dispersion of the pigment due to the optimal selection of the type and content of the additive.
To explain the dispersing effect of additives, we consider the effect of surfactants on the surface tension of solutions of polyphenylsiloxanes and wetting of aluminum pigment, described by us in [
30]. We have previously proven the surface activity of the studied additives in a polyphenylsiloxane composition at the liquid–gas interface (“polyphenylsiloxane solution/air”) [
30]. The minimum surface energy for solutions of polyphenylsiloxane and all surfactants was observed at CS 0.25 g/dm
3. The effect of surfactants on the change in wetting performance in industrial varnish (SC10%) is closely correlated with the results of our study of the dispersibility of pigment presented on
Figure 7.
According to
Figure 7, the maximum increase in ΔW
cm is recorded for PEPA on the pigment/aluminum substrate; at the same time, it is characterized by the greatest dispersing activity. Thus, the given content of additives in the compositions provides an improvement in the wetting of the pigment with solutions of polyphenylsiloxane. Based on all of the above, it can be argued that the studied additives exhibit surface activity at the interface of the “liquid/gas” phases (reducing the surface energy of solutions of polyphenylsiloxanes) and “liquid/solid” (improving the wetting of the pigment), as a result, there is an improvement in the dispersion of the pigment in the enamel. The obtained results can be explained by the possible adsorption of the studied additives on the active/adsorption centers of the pigment.
The dispersing activity of the studied additives, revealed by computer-optical microscopy, is confirmed by the previously shown decrease in the sedimentation rate of suspensions, presented on
Figure 8.
The three studied surfactants according to the degree of influence on the sedimentation rate of suspensions can be arranged in a row (followed in descending order of stability): PEPA > Telaz > AS-1, which is completely consistent with the results of the study of the dispersing activity of surfactants by computer-optical microscopy.
Using the Taguchi method, and on the basis of Equations (5) and (6), the optimal surfactant and solvent contents in the enamel were determined, ensuring maximum dispersion of the pigment. For the obtained additive AS-1, nomograms for finding APDP and SNP from known surfactant and solvent contents are presented in
Figure 9.
The introduction of the studied additives into polyphenylsilaxane enamel causes an 11-fold decrease in the corrosion rate (from 0.6 to 0.053 mm/year). A similar effect of reducing the corrosion rate can be achieved without the use of surfactants by simply increasing the coating thickness (from 60 to 120 microns) from 0.6 to 0.12 mm/year. However, in this case, the coating will have a significantly low protective resource due to its cracking. The increase in the anticorrosive resistance of the coating, with an increase in the content of PEPA in the coating from 0.25 to 0.5 g/dm
3, can be explained by the inhibitory activity of the introduced additives, primarily amines, which can be adsorbed on the active corrosion centers of the steel substrate and shield them. The effect of the PEPA on the dispersion of the pigment can be seen from
Figure 6; as a result, the decorative properties (roughness, gloss, etc.) should improve in the coating.
A logical continuation of this study is to study the influence of the considered additives on the protective and decorative properties of coatings. It would be especially interesting to check the effect of surfactants on the heat resistance of coatings (by thermogravimetry, in the temperature range from 100 to 450 °C).