1. Introduction
With the continuous development of the economy, society’s demand for energy is increasing. In the traditional energy industry, each energy network’s single operation and centralized energy supply mode are difficult to link with different energy sources [
1], and they cannot improve overall energy efficiency [
2]. With the progress of renewable energy sources such as wind power and hydropower, the ability to absorb renewable energy has become an important goal for future energy systems [
3,
4]. In this context, integrated energy system (IES) has become one of the most important trends in the future energy field [
5,
6,
7].
IES includes a variety of energy networks such as natural gas, heat, and power. The connection and mutual coupling between different subnetworks improve overall efficiency but put forward higher requirements for the system’s stability [
8]. Only one single energy network will be affected when a traditional energy system fails, but when an IES fails, the coupling between different energy networks will lead to cascading failures [
9]. For example, a natural gas network and a power network are coupled through a gas turbine, and the failure of the natural gas network may cause the failure of the power network as the gas turbine fails. Therefore, to ensure the safe and stable operation of IES, it is necessary to research the fault response and robust operation methods of IES.
For the failure of IES, Li et al. [
10] analyzed the reliability of an IES under three different operation objectives and verified the reasonability of the proposed indices and flexible scheduling of energy flow. Moslehi et al. [
11] built a three-dimensional matrix to combine failures and different operational periods to realize the quantification of failure loss in IES. Benjamin et al. [
12] defined a novel criticality index as the ratio of the output change to the capacity of the failed component. The computation of the criticality index makes it convenient to develop risk mitigation measures. Dehghani et al. [
13] studied the impact of false data injection attack on distributed generation systems. The result showed that the attack on loads and prices would lead to serious damage to the network as well as economic losses. The above research studies mainly focused on evaluating the reliability of IES and quantifying the possible impact of failures. The elimination of the impact was achieved by adjusting the equipment in IES without considering the possibility of using external equipment. This paper aims to find a way to eliminate the influence of failures in IES through the access of external equipment.
As a new energy storage system, compressed air energy storage (CAES) has wind power absorption, electricity storage, and thermal energy storage capabilities [
14,
15,
16]. At present, the ability of CAES to mitigate electricity scarcity has been proven [
17], and CAES’s cogeneration will not affect electric power generation [
18]. The similar multi-energy flow structure of CAES and IES makes CAES one of the best choices to eliminate the influence of failures in IES. In the various types of CAES, adiabatic compressed air energy storage (A-CAES) is proven to have the highest energy storage efficiency [
19] because the compression process is adiabatic. The number of compressor stages also has an impact on the performance of CAES [
20,
21], and less compression is suggested for a large heating supply [
22]. The integration of thermal energy storage (TES) and A-CAES improves the power and energy densities of the system [
23,
24], and the integrated system is called advanced adiabatic compressed air energy storage (AA-CAES).
In terms of joint operation of AA-CAES and IES, current research mainly focuses on the integrated system’s operation optimization and structure improvement. The economic advantages of the joint operation of CAES and IES have been proven [
25]. Capacity optimization [
26], emission reduction [
27], and cost optimization [
28] become the improvement targets of the CAES and IES joint system. The integrated system of AA-CAES and IES has better performance under variable working conditions [
29,
30]. Although the advantages of AA-CAES in improving the economics of IES have been demonstrated, the role that AA-CAES can play in realizing the robust operation of IES has not been involved.
In this paper, an integrated system composed of an IES and an AA-CAES is proposed. Two models to simulate possible failures in the IES are established, one pump failure model to simulate equipment failures and one gas pipeline failure model to simulate network failures. A robust operation method using AA-CAES is designed to maintain the balance of subnets in the IES. In this method, the energy release process of the AA-CAES is split into a heat-ensuring part which uses the high-temp tank to keep the balance of the heat subnet, and a power-ensuring part which uses the first stage of the air turbine to keep the balance of the power subnet. In order to verify the feasibility and economic efficiency of the AA-CAES method in ensuring the robust operation of the IES, two simulations are carried out in Apros (dynamic process simulation software). The first simulation is carried out under steady conditions, and the effectiveness of the AA-CAES method is verified by comparing the IES output values before and after applying the AA-CAES method during the failure period. The second simulation is carried out under dynamic conditions, and the incomes of the IES during the failure period are compared after applying the AA-CAES method and another method that uses a spare boiler instead of AA-CAES.
3. The Proposed Robust Operation of IES
3.1. Modeling of IES Failure
Water pumps play a key role in the stable operation of IES as an important fluid component [
34]. When a water pump fails, it is usually manifested as a decrease in the pump’s head. The pressure difference between the front and rear of the pump cannot be maintained in a normal state and the flow through the pump decreases. After preliminary research, a failure model of the circulating pump in the Li-Br absorption chiller is proposed. The similarity law of pump [
35] is as follows:
where
is the flow, m
3/h;
is the head, m;
is the speed, r/min; subscripts 1 and 2 represent conditions 1 and 2.
From Equation (12), the change of pump speed will cause the change in the head. Because of this, a speed control system for the circulating pump is established. The pump failure is simulated by adjusting the speed of the pump, thereby realizing the dynamic simulation of the automatic occurrence and elimination of the failure.
As shown in
Figure 1, the IES has three energy subnetworks: natural gas, heat, and power. The natural gas subnetwork supplies natural gas to the CHP system and the gas boiler to heat water. Due to the coupling between the subnetworks, when the natural gas subnetwork fails, it will affect the power subnetwork and cause cascading failures of heating. Therefore, a leakage failure model of the natural gas subnetwork is built. According to the hole model of pipelines, the relationship between the leakage flow and the hole diameter is as follows [
36]:
where
is mass discharge rate, kg/s;
is hole area, m
2;
is Mach number of the flow;
is pressure, Pa;
is molecular weight, kg/kmol;
is the ideal gas constant, J/kmol·K;
is temperature, K;
is the ratio of specific heats.
After considering the pipeline and the hole’s diameter, the leakage flow is set to be 30% of the normal flow. The leakage holes are set on the supply branches of the CHP system and the gas boiler. Due to the lack of pipeline leakage module in Apros software, a pipeline branch model is established to realize the impact of pipeline failures on the output of the IES. The model is shown in
Figure 2.
The pipeline leakage model uses the throttle model to simulate the leakage of the main pipe. The diameter of the leaking branch and the hole in the throttle are set to ensure the leakage flow is 30% of the normal flow.
3.2. Our Robust Operation Method
An integrated system composed of the IES and an AA-CAES is built to ensure the normal operation of the IES under failures. The equipment parameters of the AA-CAES are from TICC-500 [
37]. The model of TICC-500 is shown in
Figure 3. The equipment parameters are shown in
Table 2.
The operation process of the AA-CAES can be divided into two parts: an energy store process and an energy release process. During the energy store process, the motor powered by a wind turbine drives a five-stage compressor to generate high-pressure air, and the air is stored in two air storages. Between each compressor stage, the compression heat is used to heat water that flows from the low-temp tank and is stored in the high-temp tank and the mid-temp tank. The compression heat of the last stage is discarded as it cannot heat water to the fixed temperature. During the energy release process, a three-stage air turbine uses the air to drive the generator to generate power after being slowed down by the decelerator. The intake air temperatures of the three stages in the air turbine are all designed as 100 degrees, and the air is heated in four heaters by the water stored in the high-temp tank and the mid-temp tank. After being used to heat the air, the water flows back to the low-temp tank to complete the whole cycle.
Since the stable operation of the IES under failure conditions requires simultaneous protection of power and heat subnetworks, a robust operation method using AA-CAES is formulated, as shown in
Figure 4.
The energy release process of AA-CAES is split into two parts: a heat supply part and a power supply part. In the heat supply part, the water stored in the high-temp tank is used to heat the water from the water collector then flows back to the low-temp tank to complete the cycle. Meanwhile, the water in the mid-temp tank is used to heat the air in the pre-heater to ensure the fixed intake air temperature of the air turbine. In the power supply part, only the first stage of the air turbine is used to power the generator since the high-temp tank has been used. The control system monitors the temperature of the water collector and the shaft power of the CHP system to determine when to start the energy release process of the AA-CAES.
In the calculation process of the AA-CAES method, a one-dimensional unsteady homogeneous flow model is used [
38]. The equation system of the model is solved using an implicit backward Euler method with a SIMPLER algorithm [
39]. The proposed AA-CAES method is considered to have O (n
2) computational complexity [
40].
4. Simulations and Analysis of Results
The AA-CAES model and the IES model are built in Apros. To simplify the models, the assumptions of the IES model are listed in
Table 3, and the assumptions of the AA-CAES model are listed in
Table 4.
Model validation of the AA-CAES and the IES is designed to verify the accuracy of the two models. Two simulations are carried out to verify the effectiveness of the proposed AA-CAES method in balancing heat subnet and power subnet under steady conditions and economic advantages under dynamic conditions by recording the system response under failures and robust operation methods. The first simulation shows the response of IES under two failures and the response after the AA-CAES method is enabled. The second simulation compared the income of the IES with the AA-CAES method and spare gas boiler method under dynamic operation and pipeline failure conditions. The computer’s CPU used for the simulations is E5-2630 V3, and the software used is Apros 6.09.
4.1. Model Validation
4.1.1. AA-CAES Model
Figure 5 shows the result of the AA-CAES model’s energy storage process. The mass flow of the air is set to 1667 kg/h to match the design value of TICC-500. The initial pressure of the air storage was set to 2.5 MPa to match the lower limit of the air storage pressure.
Figure 5a shows that the air storage pressure rises linearly during the energy storage process, consistent with the experimental results of TICC-500 [
37]. Due to the lack of experimental parameters of the tanks, it is hard to verify whether the simulated value of the high-temp tank and the mid-temp tank is consistent with the experimental value. However,
Figure 5b shows that the high-temp tank and the mid-temp tank already have the heating capacity, so it can be considered that the AA-CAES model has been verified.
4.1.2. IES Model
Figure 6 shows the result of the IES model’s dynamic operation. The power of the CHP system and the gas boiler is set to maximum, and the power of the GSHP is controlled to meet the heat demand. The results show that the error between the heat supply of the IES model and the actual heat supply is less than 10%. After removing the period when the heat supply changes drastically, the error of the IES model is less than 5%. The accuracy of the IES model has been verified.
4.2. Simulation of IES under Steady Conditions
The heat demand of the IES is 7 MW, and all equipment runs at designed power. The power generated has a surplus of 89 kW under steady conditions. The temperature of the water collector is recorded from “Temperature” of “Horizontal Tank” in Apros software, the heat supply of the IES is recorded from “Average heat flow on tube surfaces” of “Counter Current Heat Exchanger”, and the power of the purchased electricity is recorded from “Produced active power” of “Elec. Generator”.
Figure 7 shows the heat and power subnetworks response of the IES during the pump failure period. The failure was set to 600 s to ensure the failure occurs in the IES during stable operation, and the total simulation time was 3600 s. During the pump failure period, the flue gas generated by the CHP system cannot be used to heat water. Therefore, the temperature of the water collector decreased from 47.7 °C to 45.6 °C, which reduces the heat supply from 7 MW to 6.62 MW. Since the CHP system generates electricity, the pump failure had no impact on the power subnetwork. The negative electricity purchase in
Figure 7b indicates a surplus of electricity in the IES, and there is no need to purchase electricity from the external network.
Figure 8 shows the heat and power subnetworks response of the IES with AA-CAES method during the pump failure period. The failure was set to appear in the 600 s and was eliminated in the 1800 s to meet the maximum energy release period of the AA-CAES, and the total simulation time is 3600 s. When the pump failure was detected, the high-temperature water stored in the high-temp tank of the AA-CAES released to heat the water in the water collector of the IES to maintain the normal heat supply. The water collector temperature was kept above 47.5 °C and the heat supply was kept above 6.95 MW during the failure period. After the failure, the temperature of the water collector rose, the AA-CAES was closed, and the IES returned to a stable operation state. The integration of the IES and the AA-CAES kept the balance of the heat subnetwork, ensuring that the pump failure will not have an excessive impact on the IES.
Figure 9 shows the heat and power subnetworks response of the IES during the pipeline failure period. The failure was set to 600 s, and the total simulation time was 3600 s. Unlike the pump failure, the pipeline failure caused a reduction in the fuel of the gas boiler and the CHP system, which led the temperature of the water collector to decrease from 47.7 °C to 45.7 °C and heat supply to reduce from 7 MW to 6.65 MW. The IES purchased 10 kW from the external network to keep the balance of the power subnet.
Figure 10 shows the heat and power subnetworks response of the IES with AA-CAES method during the pipeline failure period. The failure was set to appear in the 600 s and was eliminated in the 1800 s, and the total simulation time was 3600 s. When the pipeline failure was detected, the control system opened the high-temp tank and started the discharging process of the AA-CAES to deliver heat and electric power to the IES. During the pipeline failure period, the water collector’s temperature was maintained at 47.7 °C, and the IES generated a surplus of electric power about 90 kW, which was consistent with the normal operation of the IES. After the failure was eliminated, the AA-CAES was shut down, and the IES gradually returned to normal operation.
4.3. Simulation of IES under Dynamic Conditions
4.3.1. Operation of the IES during Failure Period
Since the power of the Li-Br absorption chiller is 275 kW under dynamic conditions, which accounts for less than 5% of the IES heat supply, the pump failure will not have much impact on the heat supply of the IES. According to this, only the pipeline failure is considered in the dynamic operation of the IES. The failure is set to appear at 9 o’clock (32,400 s) and is eliminated at 11 o’clock (39,600 s). The total operation time is 24 h (86,400 s). The heat supply of the IES and power of equipment are recorded from “Average heat flow on tube surfaces” of “Counter Current Heat Exchanger” in Apros. The result of the IES operation under pipeline failure is shown in
Figure 11.
The pipeline failure resulted in a power decrease of the gas boiler and the CHP system. The power of the GSHP remained the same as normal since the IES purchased electricity from the external network, but the power of the gas boiler and the CHP system decreased because of the lack of gas.
The two robust operation methods were initiated to eliminate the impact of the pipeline failure on the IES. The results of the IES operation with two methods under pipeline failure conditions are shown in
Figure 12 and
Figure 13.
During the IES operation under pipeline failure conditions, the heat supply results using two methods both met the heat demand. In the method using AA-CAES, the water level of the high-temp tank dropped from the highest level to the lowest level during the failure, which means two hours is the maximum thermal energy release period of the AA-CAES under the simulated conditions. The decrease of the IES’s heat supply with AA-CAES at 11 o’clock (39,600 s) in
Figure 12a can also prove this. In the method using the spare gas boiler, the GSHP was set to maximum power during the failure while the power of the spare gas boiler was controlled to meet the heat demand. As there is no limit in the spare gas boiler method such as the water level of the tanks, the heat supply of the IES with the spare gas boiler was maintained as normal in
Figure 13a.
4.3.2. Economic Analysis
The local electric price is CNY 0.94 per kWh, the gas price is CNY 3.12 per cubic meter, and the heating income is CNY 100 per GJ. The dynamic operating income of the IES in one day with the two robust operation methods is calculated as shown in
Table 5.
During the dynamic operation, both robust operation methods using AA-CAES and spare gas boiler can guarantee the stable operation of the IES. In terms of the dynamic operating income, the income of the AA-CAES robust operation method is CNY 1036.96 higher than the income of the spare gas boiler method. The result verifies the possibility of the integrated operation of IES and AA-CAES, and it also reflects the economic advantage of using the AA-CAES robust operation method during the pipeline failure period.