1. Introduction
Soybeans originated in East Asia and were domesticated from wild soybeans (
Glycine soja) between 1700 and 1100 B.C. and are now grown worldwide [
1]. However, soybean production and utilization were limited within or near its center of Origin (the Orient) for centuries. The first recorded use of soybeans in the U.S. was in 1765 in Savannah, GA. It is thought that Samuel Bowen, a former seaman of the East India Company, brought soybeans to the U.S. from China via London. However, soybeans did not become widely cultivated in the U.S. until the mid-nineteenth century when soybean seeds were first grown in the Midwest. Soybeans continued to gain popularity in the 1870s when farmers began to use soybeans as forage for livestock [
2,
3], but it was not until 1917 that soybean meal was first reported for use as livestock feed. Since then, the soybean processing industry has continued to expand, and by the mid-1970s, the U.S. had been responsible for two-thirds of the world’s soybean production (University of Nebraska-Lincoln) [
4]. Today, the U.S. is a global top producer of soybeans, with soybeans as the second largest row crop in the U.S. [
5]. In 2023, 33.8 million hectares of soybeans were planted in the U.S., producing 4.16 billion bushels of soybeans. The total value of the crop exceeded
$60.7 billion. From the 2023 soybean crop, the U.S. produced 48 million metric tons of soybean meal at an average price of
$498.14 per metric ton. Also, an estimated 11.9 million metric tons of soybean oil was produced in the U.S. in 2023 at an average price of
$1439 per metric ton [
5].
Soybeans comprise almost 90% of U.S. oilseed production, with the U.S. as the second leading exporter of soybeans (USDA, ERS) [
6]. More than 80% of U.S. soybeans are grown in the northern Midwest region of the U.S., with Iowa, Illinois, Minnesota, and Indiana as the top four soybean-producing states producing more than 49% of the annual U.S. supply [
7]. Most U.S. soybeans are planted in late spring to early summer (May to June) and harvested in autumn (late September through October), depending upon the region (USDA, ERS) [
8]. When mature in late September and October, the soybean seeds and plant turn yellow in color and are ready for harvest. With favorable dry weather conditions, the mature soybeans are harvested, dried, and cleaned from debris (sticks, stones, stems, etc.) and prepared for processing in the production of various meals for use in animal diets.
The solvent extraction process is used to produce SE SBM, and almost all oil is removed from soybeans. Without oil extraction, full-fat soybean meal (FFSBM) is produced, and it is a good source of dietary energy in poultry feed [
9]. By using FFSBM, the cost of mixing liquid vegetable oil feed components can be avoided and is more economically feasible. Wider utilization of FFSBM has gained more acceptance, especially in regions without local soybean processing facilities. The use of FFSBM can save the cost of transportation associated with the shipment of soybeans to a large solvent extraction plant and return shipment. Hence, extrusion processing to produce FFSBM is easy to manage under these circumstances and is more practical and economically attractive [
10].
The inclusion of FFSBM is an easy way to add fat to poultry diets without the need for special spraying devices in the mixer and liquid handling and storage. Generally, lipid feed components must be heated to a liquid state before adding to the feed, but this step can be omitted with the utilization of FFSBM. The lipid component of FFSBM is more resistant to lipid oxidation and rancidity and can be stored for a longer duration as compared to individually stored fat and oil feed components. FFSBM produced by organic soybeans is a great way to raise organic poultry for a niche market worldwide, and solvent-extracted soybean meal cannot be used for this purpose [
11]. Interestingly, global utilization and market expansion of full-fat soybean meal is projected to have substantial growth between 2023 and 2031, driven by an 11.89% Compound Annual Growth Rate (CAGR), which is expected to increase the market value of soybeans to approximately
$149.3 billion by the year 2031 [
12].
Moreover, the COVID-19 global pandemic significantly impacted the production, supply, availability, and cost of palm (Malaysia) and coconut oil (Philippines), which are major sources of dietary energy in the diets of poultry and livestock globally and are utilized for binding in pelleted diets [
13]. Reduced production and availability of these items have created substantial increases in the cost of these commodities and have been reflected in the rising global cost of livestock and poultry feed. Hence, it has become imperative to discuss the use of alternative feed ingredients that can serve as replacements for these vegetable oils in poultry feed formulations. In this review, we aim to revisit the use of full-fat soybean meal as a solution and alternative to these current global shortages and rising costs. While full-fat soybean meal prepared from conventional normal-oleic soybean cultivars has existed for over 50 years [
13], utilization of full-fat soybean meal has been under-utilized within the poultry animal feed markets. Moreover, in this review, we explore the utilization of high-oleic soybean cultivars for the production of full-fat, high-oleic soybean meal is also explored. Thus, in this review we also aim to discuss the feed processing of normal-oleic and high-oleic soybeans with retention of their natural fat content and comparison of these soybean meals.
2. Nutrition
Soybeans have traditionally been grown primarily for their oil, with the remaining cake used to produce meal rich in digestible amino acids [
14]. Ninety-five percent of the world’s extracted soy oil is used as edible oil in the food industry [
15]. Interestingly, only a small percentage (2%) of the globally produced soybean meal is utilized for human consumption. Ninety-eight percent of globally produced soybean meal is predominately used for animal nutrition [
16], with the poultry industry utilizing approximately 64%, swine-24%, beef and dairy cattle-10%, and 2% for domestic animals of all U.S. produced commercial soybean meal [
17].
Soybeans provide more crude protein and a superior amino acid profile when compared to other legumes nutritionally [
18]. Soybean meal (defatted, partially defatted) provides an ideal dietary amino acid profile when fed with corn in livestock rations, with the exception of methionine. Soybeans are limited in methionine; thus, finished feeds must be supplemented with synthetic methionine [
18]. However, even with synthetic amino acid supplementation, performance can be adversely impacted by the presence of raw or marginally processed soybeans in finished feed [
19]. Unprocessed soybeans and soybean meal are about 35% and 40% carbohydrates, respectively, with most present as non-structural oligosaccharides and a small portion as pectic polysaccharides [
20], and approximately 6% as non-starch polysaccharide crude fiber [
18] possessing anti-nutritional properties [
21]. Unprocessed whole soybeans contain a number of anti-nutritional factors that have been shown to adversely affect animal growth performance caused by reduced protein digestion and absorption, resulting in reduced feed efficiency [
22,
23]. Among the most important anti-nutritional factors are trypsin inhibitors and lectins [
23]. The two most crucial trypsin inhibitors found in unprocessed soybeans are Bowman-Birk inhibitors and Kunitz inhibitors, which provide protection to the germinating plant from microorganisms found within the soil and air prior to seed maturation. Typical levels of these trypsin inhibitors (TI) found in unprocessed soybeans range in activity levels between 20 and 35 g/kg, with the recommended threshold level of 4 g/kg in finished feed [
17]. These trypsin inhibitors negatively impact nutrient digestion and absorption, resulting in reduced performance and animal growth. Animals fed diets containing unprocessed soybeans experience pancreatic enlargement as a result of overproduction of pancreatic trypsin and chymotrypsin [
24,
25]. Additionally, trypsin inhibitors have been shown to adversely impact nitrogen retention, causing increased excretion of metabolic nitrogen [
26].
Soybean seeds and soybean meal contain a moderate level of carbohydrates (35–40%), with only a small fraction having anti-nutritional properties [
21,
25,
27]. To date, heat treatment is the most used feed processing method to reduce and/or inactivate anti-nutritional factors. However, studies have shown that anti-nutritional factors, Bowman-Birk inhibitors, phytates, and oligosaccharides are not heat-labile [
28]. Sixty to eighty percent of the total phosphorus found in unprocessed whole soybeans is phytate-bound and has reduced bioavailability due to the lack of endogenous phytase to digest phytate-bound minerals [
29]. Moreover, studies have demonstrated that soybeans contain carbohydrase inhibitors, such as pectins and non-starch polysaccharides [
21,
27], which prevent the utilization and digestion of the carbohydrate fraction of the seed for dietary energy in poultry [
28,
30]. Unprocessed soybeans have moderate to high levels of trypsin inhibitors [
23,
25] in combination with low levels of sulfur amino acids, which greatly reduce the bioavailability of amino acids in soybeans [
31].
Soybean breeders have worked for decades to identify quantitative trait loci (QTL) that are associated with phenotypic traits to enhance or alter seed nutritional composition or characteristics. Monsanto released the first genetically modified soybean line to the U.S. market with a glyphosate-resistant, “Roundup Ready” series of soybeans in 1996, and by 2014, 90.7 million hectares of these genetically modified soybeans were planted globally [
32,
33]. Methionine and cysteine content are traditionally limited in soybeans [
34], and soybean breeders have been particularly interested in identifying QTL to enhance seed levels of methionine and cysteine and, hence, in soybean meal. Nonetheless, some studies have reported that genetically modified (GM) soybeans with increased total seed protein content had reduced crop yield and oil content [
34,
35].
Increased routine commercial use of affordable phytase feed supplementation has led to reduced emphasis on breeding programs aimed at reducing anti-nutritional factors in soybean lines [
36,
37,
38]. Nonetheless, soybean breeding programs have successfully developed GM soybean lines with reduced levels of anti-nutritional factors [
39]. In addition, soybean breeders have aimed to genetically enhance the levels of soluble sugars found in soybeans, such as sucrose (primary), fructose, and glucose (trace amounts), and multiple QTL have been identified that are associated with sucrose content in the seed [
40,
41]. Enhanced seed composition of sucrose and/or other sugars is highly desired for improved soy food flavor.
3. Processing Methods
“Cooking” is the simplest method for processing soybeans and other oilseeds. In these simple cooking methods, soybeans are submerged in water and heated for 30 minutes to 120 minutes, followed by air or mechanical drying. Other cooking methods involve roasting soybeans or other oilseeds using temperatures between 100 and 210 ℃, with various direct (flame) or indirect (coal burners, oven) heat sources with a minimum exposure time of approximately 20 seconds followed by milling. Flaking is a hydrothermal processing method that involves the use of injected low-pressure steam into a conditioner to cook the bean, releasing the oil of the beans in the press when rolled between two rollers, transforming the soybeans into flakes [
42].
Processing of soybeans for oil production is conducted at soy oil processing plants, which traditionally extract the oil from the bean using solvent extraction methods. After harvest, the cleaned and dried soybeans are cracked under the pressure of corrugated rollers, creating bean particles of various sizes while removing the hull and outer husk (
Figure 1). The removal of the outer husk prevents the retention of residual oil within the soy cake. Moreover, the removal of the outer husk reduces the fiber content while increasing the final protein content in the remaining soy cake after oil extraction [
42]. Dehulled soybeans are conditioned using rotating drums with steam at 149 ºF. The conditioning and flaking process ruptures the cell walls of the seed, allowing the release of oil. During conditioning and flaking, the surface area of the soybean seed is increased by flattening and stretching the bean, causing the release of oil [
42]. Lastly, successive hexane solvent washes are utilized to extract oil from the conditioned flakes. After solvent extraction, the residual hexane solvent is removed from the soybean flakes using de-solventization (
Figure 1), producing the final soybean cake with the intended use as solvent-extracted defatted soybean meal [
43,
44].
Solvent-extracted soybean oil from conventional normal-oleic soybeans has a typical fatty acid composition of 51% linoleic acid, 7–10% α-linolenic acid, 23% oleic acid, 10% palmitic acid and 4% stearic saturated [
45,
46]. However, current plant breeding programs have modified the fatty acid profile of new soybean cultivars with genetic modifications to the Δ9 and Δ12 desaturases to enhance the oleic fatty acid content while keeping the linoleic levels low with reduced linoleic acid, producing high-oleic soybean cultivars with increased oxidative stability, positive sensory flavor profiles, and improved nutritional profiles for animal feed use [
46]. In 2010, DuPont Pioneer released the first line of high-oleic soybeans with enhanced levels of oleic acid greater than 80% [
46].
Oil extracted from high-oleic soybeans has a lipid fatty acid profile of about 75% oleic acid, 8% linoleic acid, 2% α-linolenic acid, and 12% saturated fats [
47]. High-oleic soybean oil has superior heat stability and longer fry life compared to conventional soy oil. Moreover, studies have demonstrated that dietary replacement of vegetable oils high in saturated fatty acids with vegetable oils high in monounsaturated fats (oleic acid) may reduce the risk of coronary heart disease [
48]. Hence, several animal feeding trials have been conducted to examine the dietary effects of the use of full-fat soybean meal and extruded soybean meal as an alternative to solvent-extracted defatted soybean meal and soy oil or poultry fat as separate feed ingredients in poultry feed formulations [
49,
50]. Additionally, these research interests have become of greater interest with the reduced competitive use of edible plant oils as biofuel [
51].
Extruder-expeller processing is also utilized to produce partially defatted soybean meal [
44], leaving 6–7% residual oil within the soy cake [
42,
43]. Dry extrusion processing uses no external heat and relies on the heat generated from the mechanical friction of the material passing through the screw barrel of the extruder. The mechanical screw press has a vertical feeder and a horizontal screw with an increasing diameter, which increases the pressure exerted on the oilseeds as they move along the length of the screw press. The barrel of the screw contains slots along the length, allowing the release of internal pressure and draining of extracted oil for collection in a trough below and the final discharge of the partially de-oiled cake at the end of the screw. Partially defatted soybean meal produced using extruder-expeller processing has traditionally been used in organic poultry feed, with nutritional qualities comparable to those of conventional solvent-extracted defatted soybean meal. Nonetheless, a number of investigations have reported large variations in the nutritional quality of extruded expeller-processed soybean meal with reduced amino acid composition [
52].
Without oil extraction in the dry extrusion process, a full-fat soybean (FFSBM) meal is produced with a nutritional profile of approximately 38–40% crude protein and 18–20% crude fat [
10,
11,
50]. Studies conducted by Ravindran et al. [
53,
54] demonstrated that FFSBM collected from four commercial feed mills in Southeast Asia had greater AME than defatted soybean meal (SBM) but less digestibility of dietary protein and amino acids, with values of crude protein, fat, AME, and standardized ileal digestibility coefficient of protein of 351 to 399 g/kg, 177 to 192 g/kg, 12.62 to 15.46 MJ/kg and 0.763 to 0.821, respectively. However, these studies utilized a small sample size and unknown processing history of the commercial feed mills selected. Chemical analysis of various processed soybean meals has shown that FFSBM has higher levels of metabolizable energy and crude fat, with partially defatted extruded expelled soybean meal and solvent-extracted defatted soybean meal providing higher levels of dietary protein [
55,
56].
Extrusion, micronizing, and jet-sploding are other processing methods used frequently with soybeans and other oilseeds. The extrusion process utilizes high temperatures (80–200 °C) with short intervals of time (10–270 s) for processing soybeans [
57]. Soybean extrusion using a high-shear process requires a residence time of 15 seconds with a maximum temperature of about 5 seconds [
57]. The extrusion process can be either performed using dry processing or wet processing. Dry processing occurs when frictional heat is produced between the beans and the extruder barrel as it travels along the barrel. Wet extrusion processing utilizes steam along with the mechanical energy generated in the screw press. Steam can also be utilized to precondition the beans or directly add them to the extruder barrel. The processing temperatures are different for both methods, with wet extrusion using lower temperatures (135–140 °C) [
58,
59], which is suitable in the presence of moisture/steam and hence requires less mechanical or frictional energy as compared to dry extrusion (150–160 °C) [
59,
60]. During dry extrusion, the pressure inside the extruder barrel is very high and can reach 40 atm [
59]. Dry extrusion processing has greater screw speeds to generate the additional shear force required to properly process soybeans compared to wet extrusion. However, wet extrusion processing of preconditioned (steam) beans provides almost double the efficiency of the extruder and reduces the wear of the extruder barrel components by 20% [
59]. The quality of soybean meal produced using different extrusion processing methods is related to the use of moisture during wet processing, which interferes with mechanical oil extraction. Upon comparison, FFSBM prepared using dry extrusion processing methods has a final moisture content of 5–6% as compared to 10% in FFSBM prepared by wet extrusion [
60,
61].
Micronizing is an infrared dry-heating processing method that uses radiant heat to thermally process grains [
62]. Micronizing involves the use of electric burners or gas to heat ceramic plates that emit infrared dry radiant heat to the beans. This processing method is highly efficient and thermally penetrates beans. Jet-sploding is an alternative processing method for oilseeds that also reduces anti-nutritional factors found in unprocessed oilseeds. The jet-sploding process exposes the beans to a stream of pre-heated air between 140 and 315 °C, causing the heating of grain to occur from the inside out with an internal temperature of 90–95 °C, resulting in intracellular water boiling and cooking of the grains within. After the jet-sploding heating process, the beans are transferred into a cylinder mill to complete the process and allow the release of the intercellular oil [
57,
63].
4. Comparative Nutrition and Utilization
Initial efforts to include soybeans in animal diets were not fruitful due to growth retardation compared to those fed other protein sources. In 1917, Osborne and Mendel established a reasonable growth rate for livestock by adding heat treatment to whole soybeans prior to their inclusion in the diet [
64]. Subsequently, it was observed that heat denatured protease inhibitors, which were responsible for growth retardation. Currently, feed manufacturers use conventional solvent-extracted defatted soybean meal as a standard against which other protein sources are generally compared [
52].
Generally, soybeans contain 160–210 g/kg of oil, and upon solvent extraction of the oil, the remaining soya cake contains only 10 g/kg oil. In general, conventional normal-oleic soybean oil contains approximately 500 grams of unsaturated linoleic (18:2) fatty acid/kg as an indispensable fatty acid for poultry [
55]. However, with the declining market for soy oil and increased consumer use of alternative plant-based oils, the use of full-fat soybeans in animal production has gained new interest in providing highly digestible protein and energy in the diets of poultry and other livestock.
The polyunsaturated fatty acids (linolenic and linoleic) present in conventional FFSBM and soybean oil are highly labile to oxidation, causing rancidity, reduced shelf-life, and off-flavors in the oil and/or soy-oil-containing products. Consequently, genetic manipulation of conventional soybeans is creating high-oleic soybeans with improved lipid chemistry, elevated oleic fatty acid content, and extended shelf-life stability. Comparatively, the primary difference found in high-oleic soybean oil is the replacement of elevated linoleic acid levels by elevated oleic fatty acid levels and reduced linoleic and linolenic fatty acid levels (
Table 1). Currently, the utilization of high-oleic soybeans has become a major research interest due to the increased stability and potential health benefits [
48,
65] of high-oleic FFSBM, high-oleic soy oil, and/or high-oleic soy oil-containing products.
While the protein (37–38% crude protein) and lipid (16–18% crude fat) contents are similar between conventional normal-oleic and high-oleic soybean cultivars, the fatty acid profiles are dissimilar in the bean and the full-fat soybean meals that are produced (
Table 2). The fatty acid profile of full-fat conventional soybean meal prepared from normal-oleic soybeans has a fatty acid profile of 11% palmitic acid, 4% stearic acid, 18% oleic acid, and 55% linoleic acid (
Table 1). In comparison, the fatty acid profile of full-fat soybean meal prepared from high-oleic soybeans has a fatty acid profile of 7% palmitic acid, 3% stearic acid, 72% oleic acid, and 11% linoleic acid (
Table 2). While full-fat soybean meal contains less crude protein as compared to defatted soybean meals, FFSBM contains greater digestible energy than defatted soybean meals comparatively (
Table 2). Full-fat soybean meal delivers dietary fatty acids to poultry in excess of their nutrient requirements, which may adversely affect carcass quality with softer carcass fat and the potential for oxidation during storage. Hence, care must be taken when utilizing conventional full-fat soybean meal in broiler feed formulations [
52].
FFSBM is a desirable high-energy poultry feed ingredient with enhanced AME in comparison to defatted soybean meal and may be alternatively utilized in food animal production as a replacement for these two-feed ingredients of defatted soybean meal and vegetable oil. However, it is necessary to consider the practical implications, economic viability, and inclusion rates. Experiments conducted by Mirghelenj et al. [
69] revealed that wet extruded full-fat soybean meal (WE-FFSBM) can be used in broiler diets up to 15% (
Table 3). In their experiment, full-fat soybean meal was wet extruded at a temperature of 155 °C for 15 s and added to four feed samples at 0, 7.5, 15, and 22.5% in place of dehulled soybean meal (D-SBM) and soybean oil. The growth performance of broiler birds was not influenced when WE-FFSBM was added up to 15%. However, when 22.5% WE-FFSBM was included in the diet, feed intake and body weight gains were reduced with reduced absorptive mucosal surface area in the upper small intestine of broilers. Due to a decrease in feed intake, body weight was reduced at the highest inclusion of FFSBM, which may be attributed to the presence of anti-nutritional factors in the FFSBM as a result of improper processing or heat treatment (
Table 3).
In parallel, Papadopoulos and Vandoros (1988) demonstrated that heat-treated FFSBM up to 15% in broiler diets did not adversely affect the body weights at 6 weeks of age [
70]. Moreover, Wang et al. (2000) demonstrated that the growth performance of broilers fed a 15% FFSBM diet was equal to or better than that of control broilers fed a 15% defatted soybean meal diet supplemented with soy oil [
71]. Todorov et al., (1999) reported no adverse effects on growth performance in broilers fed WE-FFSBM up to 20% of the finished diet [
72]. Other studies have demonstrated that broiler growth performance was not affected at 21 and 42 days of age when WE-FFSBM was included in the diet up to 14% [
73]. Another study reported that broiler body weights at 1 to 21 days of age were not affected when fed an FFSBM and solvent-extracted defatted soybean meal (SE SBM) blend [
73]. However, body weights and feed-to-gain ratios were improved in broilers fed an FFSBM:SE SBM blend of 75/25 and 100/0 at 1 to 42 days (
Table 4).
Erdaw et al. (2017) conducted experiments to study the growth and physiological response of broilers fed diets containing raw FFSBM supplemented with high-impact microbial protease [
27]. Raw FFSBM was added at 0, 10, and 20% to replace defatted soybean meal, and three levels of mono-component protease, derived from
Nocardiopsis prasina were added at 0.1, 0.2 and 0.3 g/kg diet (equivalent to ~7500, 15,000, and ~22,500 protease units/kg diet, respectively) for 0–35 days. By increasing the raw FFSBM alone in the diets, there was an increase in the weight of the pancreas by 24, 32, and 26% at days 10, 24, and 35 (
Table 5), respectively, but a decrease in apparent ileal digestibility of crude protein and amino acids at day 24. The highest villus length and mucosal depth were observed compared to other time points (day 24) when 20% raw FFSBM was supplemented with 0.2 g protease/kg. It is important to note that when fed in combination, raw FFSBM and protease supplementation did not significantly alter the body weight of broilers in comparison to the controls during the entire period (0–35 days).
In laying hen diets, FFSBM is also a valuable source of dietary protein and high-quality fats. Also, the use of FFSBM is often a preferable feed ingredient to vegetable oil sources, particularly on farms and feed mills that lack liquid handling capabilities. FFSBM provides ample amounts of lysine, the profile of unsaturated fatty acids, vitamin E, and linoleic acid [
74,
75]. In addition to these nutrients, FFSBM provides almost 30% to 50% of the nutritional requirements of riboflavin, niacin, pantothenic acid, thiamine, folic acid, and choline found within the lecithin of whole soybeans, all nutrients vital for egg production in egg-producing laying hens [
76]. Additionally, the use of FFSBM may be preferable due to less dustiness and improved palatability of the feed of laying hen diets [
75,
76]. The inclusion of 11% of a full-fat extruded soybean meal diet of laying hens reduced the cholesterol content from 11.3 to 10.1 mg/g in egg yolk, with increased egg production from 275 eggs to 283 eggs, egg weight from 60.3 to 61.6 g and FCR of 2.29 during the lay period of 324 days which was unchanged in comparison of the control group [
76]. Feed intake was also noticed to have increased from 117.1 g to 122.9 g [
75]. Senkoylu et al., (2005) conducted experimentation by incorporating 10, 16, and 22% FFSBM in layer diets in comparison to a conventional control diet during post-peak egg production [
75]. Experimental diets were provided to hens (Bovans White Strain) from 33 to 42 weeks. In this study, it was observed that FFSBM can be added up to 22% in laying hens’ diet without any adverse effects and with improvement in egg mass and FCR [
75]. Egg production was not affected so much between the control and FFSBM treatment groups. However, feed intake was reduced at FFSBM inclusion levels of 10% and 16% in comparison to the controls. In this study, egg weights (g/egg) were not significantly altered, yet there was an increase of almost 1 g between inclusion levels of 10% and 22% of FFSBM. Furthermore, egg mass (g/hen/day) and FCR were improved with the increasing inclusion of FFSBM (
Table 6).
Another aspect of this study covers the effect of different dietary inclusion levels of FFSBM on internal and external egg qualities, both of which were not adversely affected in comparison to conventional eggs [
76]. In addition, shell weight and shell thickness were not significantly different between eggs produced from laying hens fed diets with FFSBM and those fed conventional controls [
76]. The same was the case for shell thickness, Haugh unit, checked, and percentage of cracked eggs. (
Table 6). Interestingly, the most recent nutrient digestibility studies conducted in layer hens fed diets containing either full-fat (normal-oleic and high-oleic) or defatted (solvent extracted and extruded expelled) soybean meals (Maharjan et al., 2023) reported similar crude fat digestibility values ranging from 71 to 84 % and crude protein digestibility values ranging from 67 to72 % (
p > 0.05) [
49].
Ali et al., (2024) [
50] conducted a broiler feeding trial comparing a blend of SE SBM with either extruded expelled normal-oleic defatted soybean meal (EENO), full-fat normal-oleic soybean meal (FFNO), or full-fat high-oleic soybean meal (FFHO). Five hundred forty Ross-708 male broilers were randomly assigned to three isocaloric, isonitrogenous dietary treatment groups for 6 weeks (
Table 7). The EENO blend consisted of 5 to 7% SE SBM and 25 to 32% extruder expelled normal-oleic defatted soybean meal. The FFNO blend consisted of 5 to 17% SE SBM and 25 to 31% full-fat normal-oleic soybean meal. The FFHO blend consisted of 5 to 17% SE SBM+25 to 31% full-fat high-oleic soybean meal. Broilers fed diets containing a blend of SE SBM and either full-fat normal-oleic or high-oleic soybean meals had acceptable performance parameters compared to broilers fed an extruded expelled defatted soybean meal diet [
50]. From days 0 to 14, broilers fed the EENO had greater body weights as compared to broilers fed the full-fat normal-oleic (FFNO) and full-fat high-oleic (FFHO) soybean meal diets (
p < 0.001) [
77]. However, there were no significant differences in the feed conversion ratio between the treatment groups from 0 to 14 days. Nonetheless, there were no significant differences in the final 0-to-47-day body weights or feed intake (FI) between the treatment groups (
p > 0.05), while FCR was best (lowest value) in birds fed the EENO diet as compared to the FFHO treatment group with similar FCR values between the EENO and FFNO treatments. Also, broilers fed a blend of SE SBM and full-fat high-oleic soybean meal (FFHO) produced poultry meat (
Pectoralis major) that was enriched with oleic acid (
p < 0.001) and reduced saturated fat (palmitic, stearic and lignoceric acid) content (
p < 0.01) as compared to poultry meat produced from broilers fed a diet containing extruded expelled defatted soybean meal diet or full-fat normal-oleic soybean meal (
Table 8).
Comparatively, layer performance (final average body weights, feed conversion ratio, number of eggs produced, and average weekly egg mass-
Table 9) was dissimilar between hens fed diets containing either 21% solvent-extracted defatted soybean meal (SE SBM), 21% extruded expelled defatted normal-oleic soybean meal (EENO), 25% full-fat normal-oleic soybean meal (FFNO), or 24% full-fat high-oleic soybean meal (FFHO) in a 3-week feeding trial [
49]. In parallel to the findings of Ali et al. (2024) [
50], eggs produced from hens fed a full-fat, high-oleic soybean meal diet were enriched with oleic acid (
p < 0.0001) and reduced saturated fat (palmitic and stearic acid) content (
p < 0.0001) as compared to eggs produced from hens fed the other dietary treatment groups (
Table 10). Eggs produced from hens fed the FFHO dietary treatment also had linoleic and linolenic acid contents that were significantly lower as compared to eggs produced from hens fed the FFNO treatment (
p < 0.0001) [
49]. Taken together, the utilization of high-oleic soybeans and/or full-fat high-oleic soybean meal has become a major research interest due to the increased shelf stability of high-oleic soybean-containing products and due to the potential health benefits in animal production nutrition and health and/or improved lipid chemistry of the meat, eggs or milk produced.
6. Perspectives
Soybeans (Glycine max) are the most valuable and widely grown oilseed globally, with a 350% increase in global crop production between 1987 and 2018 [
68]. Today, the U.S., Brazil, and Argentina are the largest global producers of soybeans, while China and other Asian countries are the largest global consumers of soybeans, with U.S. exports of soybeans to China totaling over
$3 billion in 2019 [
77]. Much of the early success of soybeans is attributed to the U.S. Department of Agriculture (USDA) and commodity-based organizations. The Office of Foreign Seed and Plant Introduction was established in 1898 by the USDA and was responsible for introducing new soybean germplasm. Prior to 1898, only eight soybean varieties were reported to have been grown in the U.S [
66]. In 1929, two USDA scientists, Howard Dorsett and William Morse, went to Japan, Korea, and China to collect soybean germplasm, which totaled over 4000 soybean accessions over the course of two years. Currently, there are more than 22,000 soybean lines in the USDA Soybean Germplasm Collection in Urbana, IL [
67,
78].
The establishment of a soybean checkoff fund approved by Congress in 1990–1991 (Soybean Promotion, Research and Consumer Act) with contributions of 0.5% of the price of each bushel sold by soybean farmers was appropriated for sustained investments in research (in breeding, production, abiotic and abiotic resistance, new uses), and marketing has been the key to the fast and wonderful success of soybeans in the U.S. Furthermore, this success has been spear-headed under the governance of the United Soybean Board, which directs the soybean checkoff’s national efforts. The United Soybean Board consists of 78 volunteer farmer directors, often nominated by their state-level soybean checkoff organizations and appointed to the national board by the U.S. Secretary of Agriculture [
79]. In addition, many states have local soybean boards that invest local checkoff funds into their respective state programs.
The establishment of the soybean checkoff fund and the United Soybean Board, along with state checkoff funds to support sustained investments in research and marketing, catapulted the fast and wonderful success stories of U.S. soybeans. As the economies of developing countries continue to improve, the global population’s shifting dietary preferences favoring animal proteins have resulted in dramatic increases in the demand for poultry, livestock, and fish around the world, in turn increasing the demand for soybean feed products. Sustained investment by the soybean checkoff fund, alongside further improvement of world economies, will result in further expansion and demand for soybean products in the future. With continually growing economic development globally, and growing consumer demand for high-quality poultry meat and eggs, and soy-containing foods, global soybean sectors are projected to expand with greater market utilization within animal food production and food sectors and the subject of much discussion.
In the last decade, USDA scientists have aimed to conduct “farm to fork” applied research to meet USDA research initiatives to deliver a 20% increase in the quality of agricultural commodities with a 20% reduction in environmental impact and to improve the nutritional quality of the foods produced. As such, much research, development, and investment has been focused on the development of improved seed cultivar varieties and technological applications to enhance the quality of agricultural commodities and products for use in poultry and animal feed and food.
While the use of conventional full-fat soybean meal offers the benefits of reduced need for feed processing methods and cost association with solvent extraction and the need for liquid storage and handling of vegetable oils at the feed mill, utilization of high-oleic full-fat soybean meal offers a plethora of additional end-user benefits. Utilization of high-oleic full-fat soybean meals as a poultry feed ingredient reduces lipid oxidation and rancidity in finished poultry feed products and nutritionally enriches poultry meat and eggs produced with monounsaturated oleic acid, with the potential for human nutrition and health benefits. Given this, it is expected that the high-oleic soybean global market and utilization will greatly expand, driven by increased consumer preferences and demand for healthier, high-quality foods produced sustainably. The high-oleic soybean market is expected to have significant growth, with a projected CAGR of 12.8% over the next seven years, driven by the demand for healthier vegetable cooking oils and increasing awareness regarding the health benefits of consuming high-oleic soybean products.
Due to this ever-changing global landscape directly impacting the global supply, exchange, production, and cost of agricultural commodities, it is imperative that we examine the current and projected utilization of alternative feed ingredients for use in poultry and animal feed formulations. The global COVID-19 pandemic changed the trajectory of the production, supply, and cost of a number of conventional poultry feed ingredients, such as solvent-extracted soybean meal and palm and coconut vegetable oils. Hence, in this manuscript, we discuss poultry research with the replacement of these ingredients with the use of full-fat normal-oleic or high-oleic soybean meals in poultry diets.
High-oleic soybeans and full-fat high-oleic soybean meal may be a feed for the global future due to improvements in lipid chemistry and benefits offered within poultry, animal, and human nutrition. Nonetheless, much additional applied research is needed to adequately assess the limitation of high-oleic full-fat soybean meal as an alternative poultry and animal feed ingredient.