Long-Term Forecasting of Electrical Loads in Kuwait Using Prophet and Holt–Winters Models

Abstract

The rapidly increasing population growth and expansion of urban development are undoubtedly two of the main reasons for increasing global energy consumption. Accurate long-term forecasting of peak load is essential for saving time and money for countries’ power generation utilities. This paper introduces the first investigation into the performance of the Prophet model in the long-term peak load forecasting of Kuwait. The Prophet model is compared with the well-established Holt–Winters model to assess its feasibility and accuracy in forecasting long-term peak loads. Real data of electric load peaks from Kuwait powerplants from 2010 to 2020 were used for the electric load peaks, forecasting the peak load between 2020 and 2030. The Prophet model has shown more accurate predictions than the Holt–Winters model in five statistical performance metrics. Besides, the robustness of the two models was investigated by adding Gaussian white noise of different intensities. The Prophet model has proven to be more robust to noise than the Holt–Winters model. Furthermore, the generalizability test of the two models has shown that the Prophet model outperforms the Holt–Winters model. The reported results suggest that the forecasted maximum peak load is expected to reach 18,550 and 19,588 MW for the Prophet and Holt–Winters models by 2030 in Kuwait. The study suggests that the best months for scheduling the preventive maintenance for the year 2020 and 2021 are from November 2020 until March 2021 for both models.

1. Introduction

Electricity power is an essential part of today’s life, and it is the backbone of modern civilization [1]. The generation of power for daily life is crucial in every country. Different challenges worldwide in economics, environment, and growing populations require electrical systems that operate efficiently and continually all around the year. Therefore, electrical load forecasting is one of the critical tools for policymakers to make the right decision in expanding and managing the electric grid and for the management of the existing powerplants. Energy forecasting provides vital information for generating capacity, control and planning, system management, distribution, and maintenance scheduling. Accurate forecasting assures an efficient capacity planning for the growing population and increasing demand for electricity that avoids over or underestimating of utility expansion plans. In addition, it would allow proper and data-driven economic and environmental management and planning. Different planning horizons of electrical load forecasting are investigated in various publications, which are traditionally categorized into short-term, medium-term, and long-term forecasting [2,3,4,5,6]. First, the short-term forecasting investigates the sub-hourly, hourly, daily, and weekly predictions. Second, the medium-term forecasting that includes weekly, monthly, and quarterly forecasting. Lastly, long-term forecasting contains periods of a year or beyond. Each one of these planning horizons is important; however, the long-term forecasting can be considered the most critical horizon due to the consequences of the strategic and costly decisions, such as the expansion of utility plants. An overestimation of electricity demand, especially in the long-term forecasting, will result in a significant increase in the construction of unnecessary electricity generation plants. In contrast, an underestimation of electricity demand forecasting will result in a shortage of electricity production and customer dissatisfaction. Therefore, the study of this research will focus on long-term electricity demand forecasting and the use of models that give the most accurate predictions.

An enormous number of research in electrical load forecasting is found in the literature that tackles the different challenges faced by the power industry and provides a superior forecasting method for predicting the demand of the electrical load. Various types of models and methodologies are implemented for electrical load forecasting in the literature with several parameters in a range of complexity degrees to achieve the best load forecasting accuracy. The methods can be categorized into several groups, but for simplicity, it can be divided into two main groups, namely the group of conventional models and the group of artificial intelligence (AI) models [1,2,3,4,5,6]. Conventional methods include models, such as regression models, time series models, exponential smoothing, and gray models [2,4]. In contrast, artificial intelligence models include models such as artificial neural network (ANN)-based models, support vector regression (SVR), genetic algorithm (GA) models, machine learning (ML) models, and deep learning (DL) models [1,2,3,4]. These models were used as simple or hybrid models or as a combination of more than one method, whether conventional or artificial intelligence models. Generally, the artificial intelligence models are more complex than conventional models. During the last two decades, the application of the AI models in the forecasting processes was rapidly increasing compared to the conventional models, and that can be attributed to the development of different AI models and the advancement of the computers [2]. However, a relatively recent review [3] depicted that the conventional methods, such as regression and/or multiple regression, are still widely efficiently used, especially for long-term forecasting despite their simplicity.

Researchers globally tackled the long-term forecasting challenges by using different models and methodologies to achieve superior and accurate forecasting. For example, Dudic et al. [7] used a linear regression model to forecast the monthly and yearly electricity consumption for the German market, taking into account some factors, especially the higher efficiency of electricity usage from year to year. Filik et al. [8] proposed a nested combination of three subsections for modeling to reduce the forecasting error and can be used for several years ahead. Mohammed [9] examined the correlation of actual load supply with factors, such as population, gross national product, consumer price index, and weather temperature of Iraq using linear logarithmic and ANN models. García-Díaz and Trull [10] presented multiple Holt–Winters models to improve the forecasting electricity demand of the Spanish national electricity market for very short-term forecasting. Taylor [11] showed the superiority of triple seasonal methods of Holt–Winters and auto regressive moving average (ARMA) models for Short-Term Electricity Demand Forecasting. Recently, Trull et al. [12] proposed a new method to initialize the level, seasonality, and trend in multiple seasonal Holt–Winters models. Bianco et al. [13] used a trigonometric grey model with a rolling mechanism and Holt–Winters smoothing method to predict long-term non-residential electricity consumption for ten years up to the year 2020 and showed low average deviation. Hussain et al. [14] employed Holt–Winters and Autoregressive Integrated Moving Average (ARIMA) models using real data from the year 1980 to 2011 to forecast the electricity consumption for Pakistan up to the year 2020 and showed better results for the Holt–Winters model than ARIMA model. Ali et al. [15] employed a fuzzy logic model for long-term load forecasting of one year based on temperature and humidity in addition to historical load data. Ouedraogo [16] developed a scenario-based model for the African power system using the Schwartz methodology in this context and showed an increase in electricity demand of 4% by 2040. Liu et al. [17] proposed a least squares support vector machine optimized by two different models to forecast the demand of electric load in the multi-energy coupling mode. More examples can be found in several reviews carried out by Kuster et al. [3], Wei et al. [4], Ahmad et al. [5], Deb et al. [18], Khuntia et al. [19], Runge and Zmeureanu [20], and Su et al. [21]. A relatively new method called Prophet is introduced by Taylor and Letham [22] for forecasting, which has a high potential to be used in electric load forecasting. Different implementations were found for this model in recent years. For example, Yenidogan et al. [23] compared two models: ARIMA and Prophet in Bitcoin forecasting. The results show that Prophet had an accuracy of about 94.5%, which was much better than ARIMA, which had an accuracy of only 68%. In addition, Ashwini Chaudhari [24] used three models: ARIMA, Prophet, and long-short term memory (LSTM) recurrent neural networks in forecasting the prices of cryptocurrencies: Bitcoin, Ethereum, and Litecoin. The results show that the application of LSTM and Prophet led to very high accuracy between 93% and 99% for the three currencies, while the accuracy of the ARIMA model ranges between 82% and 66% only. In addition, Bianchi et al. [25] carried a comparative for heat short-term demand forecasting methods using the Autoregressive Model (ARM), Non-Autoregressive Model (NARM), and Prophet based on real data of an Italian utility company. The ARM was superior to the other models in short-term forecasting. A thorough recent study carried out by Das [26] where five different forecasting models (Simple Exponential Smoothing, ARIMA, Dynamic Harmonic Regression, Neural Network, and Prophet) were used for prediction of wind speed in two states in India (Tamil Nadu and Maharashtra). The neural network model provided the best results. However, the Prophet model showed promising results, and it was recommended to be used in the future.

Different studies about long-term forecasting for Kuwait were carried out. Almeshaiei and Soltan [27] proposed a methodology to be used as a guide for constructing electric power load forecasting models based on segmentation and decomposition of the load time series and used real daily load data from the Kuwaiti electric network and a model with a mean absolute percentage error (MAPE) value of 3.84% was reported. Al-Rashidi and El-Naggar [28] employed the particle swarm optimization to minimize the error associated with the estimated model parameters for annual peak load forecasting for Kuwaiti and Egyptian powerplants using the least error squares estimation technique to forecast the annual peak load for the years 2006 to 2010. Alhajeri et al. [29] used the cuckoo search algorithm to minimize the error associated with the estimated parameters of three long-term forecasting methods used to forecast the annual peak demands. Al-Hamad and Qamber [30] presented long-term forecasting for peak loads of Gulf Cooperation Council (GCC) countries using Multiple Linear Regression (MLR) and Adaptive Neuro-Fuzzy Inference System (ANFIS) methods. A recent study for the residential sector in Kuwait was carried out by Alajmi, and Phelan [31] created a baseline using a bottom-up approach for the end-use energy profile for the residential sector in Kuwait until 2040.

With reference to the aforementioned relevant literature, research to date has not yet investigated the performance of the Prophet model in long-term forecasting of maximum load. In this paper, real recorded data from the National Control Center (NCC) in Kuwait were used for long-term electric load forecasting using the Prophet model. The proposed method is simple yet powerful in prediction because of its features of adjusting parameters without exploring the specifications of the underlying model [22]. It consists of a decomposable time series model with three main model components: seasonality, trend, and holidays. The model is compared with a well-established Holt–Winters model for evaluation and to obtain the best forecasting model.

This study aims to contribute to the literature by investigating long-term maximum peak load forecasting performance of Kuwait peak loads using the Prophet method based on comparative quantitative analysis with the Holt–Winters forecasting method. To the best of our knowledge, no prior study has investigated the use of Prophet model in long-term forecasting of the maximum electricity load either in Kuwait’s electrical national grid or elsewhere. Furthermore, the generalizability and robustness of the Prophet and Holt–Winters methods for the long-term electric peak loads forecasting are explored and presented.

2. Methodologies

A dataset of the maximum load of Kuwait between January 2010 and May 2020 was acquired from the Ministry of Electricity and Water (MEW) to support this research. Figure 1 presents the maximum load (MW) of Kuwait for the past ten years. With reference to Figure 1, a yearly seasonality of the maximum load can be clearly observed. The maximum load peaks are within the summer period between June and August each year due to the subtropical weather nature of Kuwait with extreme temperatures in summer and cold winter seasons. In addition, the maximum load takes an increasing trend. The gradual and steady trend increase is likely to continue for the upcoming years due to the fact of the increasing population, increased factories, and the expansion of the urban and residential areas.

In order to forecast the maximum load of Kuwait for the upcoming years, forecasting models that incorporate seasonality and trends are required to ensure a well-fitted model to the actual data. In this work, Facebook’s Prophet and Holt–Winters forecasting models have been utilized in this research for the long-term forecasting of the maximum load in Kuwait.

The Prophet forecasting model that is used for forecasting the maximum load is a relatively new modular forecasting method based on various tunable parameters by analyst-in-the-loop, as shown in Figure 2. One of the Prophet forecasting method’s strengths is that it was designed to have intuitive tuning of the parameters and does not require knowledge of the underlying model. However, to date, long-term maximum load forecasting using Prophet has not been reported in the literature. Whereas, the Holt–Winters model, or else known as triple exponential smoothing, has been excessively reported in the relevant literature and was proven to be effective in forecasting energy consumption with high accuracy [32,33,34]. In addition, unlike the Holt–Winters method, the Prophet forecasting method is robust to missing data and does not require data interpolation. Furthermore, seasonality with multiple periods can be incorporated in the Prophet forecasting method to provide flexibility in modeling complex data using an analyst-in-the-loop experience. The Prophet method also enables the user to use extra regressors to present multivariate forecasting to explore the effects of different variables with a very fast-fitting procedure. In the next sections, the implementation of the Prophet and Holt–Winters forecasting methods is presented in detail.

2.1. Prophet Forecasting Method

Prophet forecasting model incorporates data trends, seasonality, and holidays that allow the possibility of modeling complicated time-series features. Multiple seasonality can be fitted as daily, weekly, and yearly patterns. The mathematical representation of the decomposed time series model is hence described as:

$$y\left(t\right)=g\left(t\right)+s\left(t\right)+h\left(t\right)+{\epsilon }_t$$

(1)

where g(t) represents the data trend function, s(t) represents the seasonality, and h(t) represents holidays effect that can be added within specific points of the data. The error term, ε_t, represents any distinctive features of the data that are not fitted by the model.

Prophet trend function, g(t), can be represented by a piecewise linear growth model or a saturating growth model. Since the maximum load data do not exhibit a saturating growth, a piecewise linear growth model is utilized as:

$$g\left(t\right)=\left(k+a{\left(t\right)}^T\delta \right)t+\left(m+a{\left(t\right)}^T\gamma \right)$$

(2)

where $k$ is the growth rate, $\delta$ is adjustment rate, $m$ is the offset parameter, and $\gamma$ represents the trend changepoints, $s_j$, and is set as $-s_j{\delta }_j$, with $a\left(t\right)$ defined as:

$$a_j\left(t\right)=\{\begin{array}{c}1 if t\ge s_j\\ 0 otherwise\end{array}$$

(3)

The change points allow the growth model to change the trend and can be utilized by the analyst-in-the-loop to fit the model better and produce reliable data forecasts. The Prophet model allows the user to specify the flexibility of the trend by the adjustment rate. It can also automatically detect the change points, or the data analyst can manually adjust them to describe trend-altering events in the time series.

For the seasonality function, $s\left(t\right)$, the time series’ multiperiod seasonality can be modeled using the Fourier series to represent the daily, weekly, and yearly seasonality. The seasonality function is hence written as:

$$s\left(t\right)={\displaystyle \sum }_{n=1}^N\left(a_n\cos \left(\frac{2\pi nt}{P}\right)+b_n\sin \left(\frac{2\pi nt}{P}\right)\right)$$

(4)

with P = 354.25 for yearly seasonality or P=7 for weekly seasonality. Lastly, to include holiday effects by the holiday function, $h\left(t\right)$, the user can define a matrix list of holidays with dates to be incorporated into the time series as a matrix of regressors, Z(t), defined as:

$$Z\left(t\right)=[1(\mathrm{t}ϵ{\mathrm{D}}_1),\dots ,1(\mathrm{t}ϵ{\mathrm{D}}_{\mathrm{L}}\left)\right]$$

(5)

$$h\left(t\right)=Z\left(t\right)\kappa$$

(6)

with D as the set of holiday dates, $\kappa ~ Normal\left(0,v^2\right)$ with $v$ as the holiday smoothing parameter.

2.2. Holt–Winters Forecasting Model

There are two variations of the Holt–Winters forecasting method: the additive and multiplicative models of the seasonal variations. The multiplicative model is suitable for a time series with an increasing seasonal pattern that is proportional to the data level. In contrast, the additive model is suitable for fitting a time series with a constant seasonal variation. In this work, the multiplicative method is utilized for forecasting the maximum load of Kuwait.

The Holt–Winters model consists of forecast equation and smoothing equations of the level, trend, and seasonality of the time series. Assuming that $s_t$ represents the seasonality, $b_t$ to represent the trend and that $l_t$ corresponds to the level with smoothing parameters of $\alpha , \beta$, and $\gamma$. Therefore, the Holt–Winters multiplicative forecast model can be expressed as:

$${\widehat{y}}_{t+h|t}\left(k\right)=(l_t+h{b}_t)s_{t+h-m\left(k+1\right)}$$

(7)

$$l_t=\alpha \frac{y_t}{s_{t-m}}+\left(1-\alpha \right)\left(l_{t-1}+b_{t-1}\right)$$

(8)

$$b_t={\beta }^{\ast }\left(l_t-l_{t-1}\right)+\left(1-{\beta }^{\ast }\right)b_{t-1}$$

(9)

$$s_t=\gamma \frac{y_t}{\left(l_{t-1}+b_{t-1}\right)}+\left(1-\gamma \right)s_{t-m}$$

(10)

where m denotes the seasonality period and the smoothing parameters defined as:

$$0\le \alpha \le 1,0\le \beta \le 1,\mathrm{and}0\le \gamma \le \left(1-\alpha \right)$$

In the Holt–Winters multiplicative method, the seasonality component is expressed relatively, and the time series can be seasonally adjusted by dividing through by the seasonality component. Equation (8) corresponds to the level, and it is expressed as a weighted average between the seasonal term and the non-seasonal term $\left(l_{t-1}+b_{t-1}\right)$. While Equation (9) corresponds to the trend of the time series, which is expressed as a weighted average of the trend between the level and previous slope $b_{t-1}$. Equation (10) corresponds to the seasonality and is calculated by the weighted average between the current and previous seasonal components of the time series.

2.3. Validation Approach

In order to validate the performance of the prediction of the models, a simulated historical forecast (SMH) approach is conducted. SMH is based on the rolling origin cross-validation approach, or otherwise known as forward chaining, where the data are split into training and testing sets and each day is tested based on the prior training data. However, this method would be computationally intensive due to conducting tests each day and would result in more forecasts that are likely to have correlated estimates of errors. While with SMH, fewer forecasts can be defined at cut-off dates and the total error can be evaluated based on all the forecast horizons. Figure 3 illustrates the process of the rolling origin cross-validation. This approach would allow the models to train on a dataset and test on another unseen dataset of the time series. Moreover, the SMH approach could be used as an indicator of the models’ generalizability in forecasting the maximum load.

In addition, to assess the performance of each model in terms of accuracy, various statistical metrics were adopted, such as root mean square error (RMSE), the mean absolute percentage error (MAPE), coefficient of determination (R²), mean absolute error (MAE), and coefficient of variation of root mean square error (CVRMSE) that can be expressed as in the following equations:

$$RMSE=\frac{\sqrt{{{\displaystyle \sum }}_{i=1}^n{\left({\widehat{y}}_i-y_i\right)}^2}}{n}$$

(11)

$$CVRMSE=\frac{\sqrt{{{\displaystyle \sum }}_{i=1}^n{\left({\widehat{y}}_i-y_i\right)}^2}}{\breve{y}}$$

(12)

$$MAE=\frac{1}{n}{\displaystyle \sum }_{i=1}^n\left|y_i-{\widehat{y}}_i\right|$$

(13)

$$MAPE=\frac{1}{n}{\displaystyle \sum }_{i=1}^n\left|\frac{{\widehat{y}}_i-y_i}{y_i}\right|\times 100\%$$

(14)

$$R^2=1-\frac{{{\displaystyle \sum }}_{i=1}^n{\left(y_i-{\widehat{y}}_i\right)}^2}{{{\displaystyle \sum }}_{i=1}^n{\left(y_i-\breve{y}\right)}^2}$$

(15)

where $y,$ $\widehat{y}$ and $\breve{y}$ represent the measured, predicted, and averaged values respectively.

3. Results and Discussion

The Prophet and Holt–Winters models are implemented in R and Python, using real data of electrical daily peak load from Kuwaiti powerplants from 2010 to 2020. The two models’ outputs are plotted in Figure 4 and Figure 5, along with the real electrical peak of daily loads. The data include Kuwait’s peak loads from 2010 to 2020. Moreover, the forecasted from 2020 to 2030, along with a 99% confidence interval, are included. The forecasted region of this period is enlarged and presented in Figure 6, along with the 99% confidence interval for both models.

The graphs in the previous figures demonstrate that there has been a steady increase in the values of daily peak loads with a yearly seasonality for both models. The two models share several key features, such as trend similarity of the forecasted maximum and minimum peaks. However, the Holt–Winters model generally shows a higher magnitude of the forecasted maximum and minimum peaks than the Prophet model. The superiority of the models is assessed from different aspects by three indicators: accuracy, generalization, and robustness. Also, the future peak loads forecasting for Kuwait is discussed, and the maximum capacity needed by 2030 is investigated.

3.1. Model Accuracy

Various accuracy and statistical performance metrics were used in this study, which include MAPE, MAE, RMSE, CVRMSE, and the coefficient of determination R². MAE demonstrates the gap between the estimated value and the real value using the absolute error. RMSE assesses the instability of model response regarding variance and sensitivity to large errors. CVRMSE normalizes the forecasted error and provides a unitless metric that evaluates the variability of the errors between real and predicted values. The advantage of using these statistical indicators is to explore various aspects of the presented models.

Table 1. The calculated values of different performance statistical metrics for both models.

Criteria	Prophet	Holt–Winters
MAPE	1.75%	4.17%
MAE	147.89	343.33
RMSE	205.64	475.76
CVRMSE	7.61%	17.59%
R2	0.9942	0.9694

presents the calculated values of five statistical performance metrics (MAPE, MAE, RMSE, CVRMSE, and R²) for both the Prophet and Holt–Winters models using the equations aforementioned in the methodology section. MAPE is one of the most used tools for measuring the accuracy of models [35]. MAPE is proposed in [4] as a reference range for evaluating the performance of energy consumption forecasting at different horizons. Highly accurate models are considered when the MAPE is less than 10%, as benchmarked in [36]. The highly accurate models were divided into levels into four sublevels for each planning horizon. For example, the long-term forecasting is divided into these sublevels: I (≤1.2%), II (1.2–2.8%), III (2.8–4.6%), and IV (4.6–10%) [4].

Accurate values of MAPE were achieved by the Prophet and Holt–Winters methods with superiority by the Prophet model. The values of MAPE were 1.75% and 4.17% for Prophet and Holt–Winters models, respectively. Both values indicate an accurate prediction of the values of both models with relatively low MAPE values. Based on the sublevels of accuracy mentioned above and in [4], the Prophet model falls within sublevel II, whereas the Holt–Winters model falls within sublevel III accuracy.

Figure 7 depicts the coefficient of determination, R², and illustrates the variations between the forecasted and real data values for both the Prophet and Holt–Winters models. Both models achieved high values of the coefficient of determination R² equal to 0.9942 and 0.9694 for the Prophet and Holt–Winters models, respectively. The MAE of the Prophet model is reported as 147.89, whereas the value of MAE for Holt–Winters model is 343.33, which is approximately more than the double of the Prophet model MAE. In addition, the Prophet model results in a better RMSE value than the Holt–Winters model with a value of 205.64. Moreover, the CVRMSE percentage of the Prophet model is less than the Holt–Winters model with values of 7.61% and 17.59%, respectively.

It is clear that the Prophet model has a superior fitting to the real data and has better performance and accuracy than the Holt–Winters model. From the five different statistical metrics, both the Prophet and Holt–Winters models show high accuracy with the superiority of the Prophet model over the Holt–Winters model.

Another measure to assess the accuracy of the models is to use the simulated historical forecast (SHF) [22,37], as depicted in Figure 8. The Prophet model forecasts have a considerably lower prediction error than the Holt–Winters model. The Prophet model’s MAPE values are limited within the range between 1.3 and 2.1 approximately, and there is no clear trend of MAPE with the forecast window. The MAPE values of the Holt–Winters model across the different forecasting periods were generally good but higher than the Prophet model. The Holt–Winters model showed a generally increasing trend of MAPE values with the increase in the forecast horizon. These results are evidence that both models exhibit a great extent of accuracy in long-term energy forecasting.

3.2. Model Generalization

The model’s generalization is assessed by the model’s ability to forecast samples beyond the training range. Figure 9 depicts the relative error variation in each of the Prophet and Holt–Winters models. The relative error percentage of the Prophet model outperforms the Holt–Winters model. The percentage of maximum relative error in the Prophet model is less than 16%, whereas the Holt–Winters model’s relative error reached 30%. Besides, the SHF results can be used to show the generalizability of both models. The Prophet model shows better generalizability than the Holt–Winters model, as suggested by the MAPE values and the relative error percentage.

3.3. Model Robustness

To test the model robustness, Gaussian white noise with different intensities is utilized and added into testing data sets of actual data. This approach has been utilized by relevant literature, such as in [38,39]. The data is split into training dataset and multiple testing sets with each set corresponding to a defined noisy intensity. Gaussian white noise is generated with four different intensities of 20%, 40%, 60%, and 80% to assess the robustness of the Prophet and Holt–Winter models. The generated Gaussian white noise samples are distributed randomly at each testing data set, with the corresponding noise intensity, and model robustness is evaluated by the effect of the noise intensity over the accuracy of the model, measured by the coefficient of determination R². Low variance in R² indicates high robustness where high variance indicates low robustness.

Table 2. The accuracy reduction of different models under various noise intensities.

Noise Intensity	Prophet	Holt–Winter
0%	0.9942	0.9694
20%	0.9892	0.9483
40%	0.9795	0.9275
60%	0.9708	0.9014
80%	0.9604	0.8883

presents the results of the R² of both models under various noise intensities.

A reduction in the coefficient of determination is associated with the increase in the noise level, as depicted in Figure 10. The Prophet model showed high R² values across the different noise intensities with a minimum value of 0.9604 at 80% noise intensity. On the other hand, the Holt–Winters model showed high values of R² but relatively lower than the Prophet model. The minimum value of R² for Holt–Winters was 0.8883 at 80% noise intensity. The results indicate that the Prophet model is more robust than the Holt–Winters model under various Gaussian white noise intensities.

3.4. Future Peak Loads Forecasting

According to the assessment of the two models, the Prophet model outperforms the Holt–Winters model and, therefore, should provide more reliable forecasting. The real data of daily peak loads consumption from 2010 to the end of May 2020 are used to forecast the daily peak load from June 2020 to 31-12-2030, with results plotted in Figure 4 and Figure 5. The forecasting plots also provide essential information about the yearly maximum peak demand. Estimating the maximum peak demand is crucial for long-term strategic decisions in terms of electricity capacity expansion plans to withstand the foreseen maximum loads. Soares et al. [40] reported that the electric peak demand is expected to reach 30,000 MW by 2030. Al-Hamad and Qamber [30] applied the Adaptive Neuro-Fuzzy Inference System (ANFIS) and Multiple Linear Regression (MLR) methods to forecast the peak loads for Kuwait in three scenarios according to the expected growth rates of the gross domestic product (GDP) for the years 2014–2024. The three sceneries were associated with high, average, and low growth of GDP. The high, average, and low growth of GDP models were increasing in different rates reaching maximum forecasted loads of 18,700, 27,300, and 44,500 MW, respectively, for the year 2024. Alhajeri et al. [41] showed that the expected demand in Kuwait is increasing by an average of 2.8% annually by 2030, and the installed capacity should be higher than 21.8 GW. Past studies [30,40,41,42,43] about the maximum peak loads forecasting showed a clear increasing trend for peak loads in the coming years, reaching about 30 GW by 2030. On the other hand, the recent study and the new forecast of MEW show a similar trend but lower in magnitude.

The long-term forecasting provides daily, monthly, and annual maximum peaks.

Table 3. Comparison between the maximum load of actual data, forecasted maximum peaks from Ministry of Electricity and Water and the Prophet and Holt–Winters models.

Year	Actual	MEW [44]	Prophet	Max 99% CI	Holt–Winters	Max 99% CI
2010	10,890		10,648	12,817	10,195	12,123
2011	11,220		10,925	13,057	11,050	13,146
2012	11,850		11,618	13,996	11,278	13,521
2013	12,060		11,700	13,995	11,882	14,164
2014	12,410		11,982	14,233	11,662	14,015
2015	12,810		12,617	15,048	12,393	14,725
2016	13,390		13,214	15,979	12,933	15,420
2017	13,800		13,646	16,482	13,500	16,088
2018	13,910		13,866	16,634	13,834	16,570
2019	14,420	14,049	14,235	17,197	14,438	17,314
2020		14,190	14,727	17,561	15,758	18,894
2021		14,331	14,900	17,771	15,943	19,026
2022		14,475	14,975	17,875	16,024	19,200
2023		14,620	15,431	18,538	16,511	19,860
2024		14,766	15,978	19,157	17,096	20,547
2025		14,913	16,184	19,208	17,316	20,858
2026		15,063	16,451	19,751	17,602	21,188
2027			16,746	20,240	17,918	21,594
2028			17,446	21,084	18,668	22,485
2029			17,836	21,372	19,085	22,972
2030			18,550	22,061	19,558	23,305

presents a comparison between actual maximum peak load data and forecasted demand from the MEW in different years (2017–2019) [42,43,44], Prophet, and Holt–Winters models. The MEW forecasting showed variations in the percentage increase in annual maximum load from 2017 to 2019 with a decreasing trend. In the year 2017, there was a yearly increase in the maximum peak load by an average of 5.4%. The average increase was reduced in the forecast for 2018 to reach 4.7% annually. However, the growth became more conservative in the statistical book of the year 2019 and reached 1% only. The forecasting for years between 2020 and 2030 by the Prophet and Holt–Winters models showed an increasing trend with varying percentages for each year, reaching a maximum peak load of 18,550 and 19,588 MW by the year 2030, respectively. The magnitude of the increase in the Prophet model is between the value of the maximum peaks of MEW in the year 2019 and the Holt–Winters model that suggests the Prophet model is more reliable when compared with the actual data. It is a common practice to have a capacity reservoir to withstand any sharp increase in the daily consumption of electricity. Accordingly, the 99% confidence interval can be used to be the capacity reservoir. As a result, the capacity reservoir should reach up to 22.1 and 23.3 GW for the Prophet and Holt–Winters models to tolerate any failure or disruption of the electrical system during the maximum peak load time by 2030.

On the other hand,

Table 4. Comparison between the monthly maximum load of forecasted maximum peaks from the Prophet and Holt–Winters models.

Month/YY	Prophet		Holt–Winters
	Max	Upper 99% CI	Max	Upper 99% CI
Aug-20	14,727	15,887	15,758	17,292
Sep-20	13,744	15,036	14,706	16,031
Oct-20	10,951	11,813	11,718	12,552
Nov-20	8771	9568	9384	10,313
Dec-20	6930	7619	7415	8034
Jan-21	6828	7534	7306	7823
Feb-21	6866	7504	7347	7962
Mar-21	8095	8684	8661	9424
Apr-21	10,079	11,120	10,785	11,814
May-21	12,821	13,873	13,719	14,743
Jun-21	14,571	15,986	15,591	16,836
Jul-21	14,899	16,263	15,942	17,436
Aug-21	14,628	16,002	15,652	16,779
Sep-21	14,173	15,180	15,165	16,363
Oct-21	11,500	12,375	12,305	13,528
Nov-21	9190	10,028	9834	10,861
Dec-21	6972	7492	7460	8122

presents the monthly forecasted maximum load peaks for 17 months from August 2020 to December 2021. The data provided in Table 4 are essential for monthly planning in the powerplants. It offers a clear vision for the expected maximum consumption of power by proposing the monthly maximum load peaks, which is essential for planning activity in powerplants, such as maintenance scheduling. Optimum planning for the maintenance schedule is vital for unit availability and avoiding any unexpected failures or shutdowns. Preventive maintenance is a cost-effective option that can be implemented when planning is accurate. The monthly maximum load peaks indicate that the best months for scheduling maintenance are from November 2020 until March 2021 for both models. Even with 99% confidence interval, the maximum peaks do not exceed 10,000 MW and 10,500 MW for the Prophet and Holt–Winters models. Additional months can be alternatives, such as October 2020 and April 2021 but with some low risk.

4. Conclusions

Long-term energy forecasting plays a pivotal role in providing insights for policymakers’ decisions, such as the need to expand the electrical power utilities. In this study, two forecasting models were utilized for long-term maximum electrical load forecasting of Kuwait; the Prophet and Holt–Winters forecasting models. Both models performed outstandingly in three performance metrics: accuracy, generalization, and robustness and provided essential knowledge for planning as follows:

• The Prophet model achieved excellent values for MAPE, MAE, RMSE, CVRMSE, and R² with values of 1.75%, 147.89, 205.64, 7.61, and 0.9942, respectively. The Holt–Winters model performance metrics were 4.17, 343.33, 475.76, 17.59%, and 0.9694 for MAPE, MAE, RMSE, CVRMSE, and R², respectively. The superiority of the Prophet model in these values indicates higher accuracy when compared to the Holt–Winters model.
• The Prophet model exhibits better generalizability than Holt–Winters, as suggested by the simulated historical forecast investigation.
• The robustness of the two models was assessed by adding white noise and found that the Prophet model is more robust than the Holt–Winters.
• The forecasted maximum peak load reached 18,550 and 19,588 MW for the Prophet model and Holt–Winters model, respectively, by 2030. An additional capacity reservoir should be available to tolerate any failure or disruption of the electrical system.
• The study suggests that the best months for scheduling the preventive maintenance for the years 2020 and 2021 are from November 2020 until March 2021 for both models.

It is believed that the insights concluded from this study would be of assistance to policymakers in estimating the future electricity demands and the strategic development plan of the State of Kuwait in addition to the maintenance schedule.