1. Introduction
Coalbed methane (CBM) is a green resource with high energy efficiency. Extraction of CBM not only increases energy supply, but can also reduce greenhouse gas emissions and the occurrence of gas disasters. China is rich in CBM resources, ranking third in the world [
1], but is highly dependent on natural gas imports. In 2018, China became the world’s largest importer of natural gas, with an import volume of 125.4 billion m
3 [
2,
3,
4]. CBM occurrence conditions in China are complex, mainly due to three factors: (i) low gas saturation, with an average gas content of 45%; (ii) low reservoir pressure, with a pressure coefficient of generally less than 0.8; and (iii) high degree of coal-seam metamorphism [
5]. Therefore, CBM is mainly exploited by underground extraction in China. CBM reservoir permeability in China is extremely low (10
−4–10
−3 mD), which is three to four orders of magnitude lower than that in Australia and the United States [
6]. Therefore, improving coal-seam permeability and increasing underground extraction of CBM has become a focus of research.
Methods that have been employed to increase the permeability of coal seams include dense boreholes, deep-hole blasting, hydraulic flushing, hydraulic slotting, and hydraulic fracturing [
7,
8,
9,
10]; however, these technologies have drawbacks. In particular, the range of coal-seam permeability enhancement is small and uneven, and the construction cost is high. To solve these problems, some scholars have proposed the use of slotting directional hydraulic fracturing (SDHF), which combines hydraulic slotting with hydraulic fracturing [
11,
12,
13]. The principle of this method is connecting a coal-seam slotting device with a high-pressure sealing drill rod. Water is forced into the slotting device through the drill rod by a pump and the water forms a high-speed jet after acceleration through the slotting nozzle; the slotting device simultaneously moves slowly into the borehole. In this way, coal around the borehole will be slotted and a regular slotted hole will be formed [
14]. After hydraulic slotting, the slotted hole is sealed and then connected to a high-pressure pump for hydraulic fracturing. Hence, the exposed area, coal-seam structure ratio, and permeability are increased. The gas flow conditions are improved and the gas extraction rate will increase. Use of this technology significantly decreases the number of drill rods required and shortens the time required for gas pre-drainage.
Ge found that the size of the slotted hole is the key parameter affecting slotting–directional hydraulic fracturing (SDHF) [
4]. The design of the slotting nozzle can enhance the water jet and its structure will significantly affect its ability to slot the coal seam [
15]. To improve the effectiveness of slotting, much research into optimized structures has been undertaken, based on various conditions [
16,
17,
18,
19,
20,
21]. Nikonov first proposed a conical straight slotting nozzle structure [
22]. Due to its high energy-transfer efficiency and simple manufacture, this nozzle has been widely used in mining, petroleum, fire, and other industries. Some scholars have found that streamlined inner-surface slotting nozzles designed on the basis of hydrodynamic theory have high energy-transfer efficiency. Li used a simple conical slotting nozzle to study the cavitation of a water jet [
23]. The results showed that the slotting nozzle can intensify the shear between the water jet and the surrounding liquid, resulting in a large amount of cavitation. The Rankin–Shape water jet slotting nozzle manufactured by Aqua-Dyne (USA) can maintain convergence and high efficiency of the water jet for a larger target distance [
24]. Liu studied the influence of slotting nozzle shape on the water jet flow coefficient and flow field [
25]. Vijay analyzed the influence of throat length of a convergent–expansion slotting nozzle on the flow-field parameters, both theoretically and experimentally [
26]. The slotting nozzle used in coal-seam slotting is, however, quite different from common slotting nozzles, especially with respect to limited slotting nozzle length and the sudden change of channel direction. The performance of slotting nozzles designed by existing experience is unsatisfactory, which seriously restricts application of this technology.
To design a slotting nozzle suitable for SDHF in coal mines, we used computational fluid dynamics (CFD) to study the effects of stable segment length L, convergent angle θ, and straight segment length l on the performance of a slotting nozzle using an orthogonal test. The slotting nozzle structure was optimized according to the performance. The optimized slotting nozzle was then used for flow measurements and slotting experiments, and compared with the existing slotting nozzle design to verify the validity of using this numerical method to optimize its structure.
2. Structural Optimization of Slotting Nozzle Design
2.1. Structural Parameters Affecting Performance of Slotting Nozzle
A conical straight slotting nozzle is most commonly used in coal-seam hydraulic slotting, as shown in
Figure 1. Due to its special working environment, the total length of the slotting nozzle is limited, and its special runner structure needs selection of different structural parameters from those of a conventional nozzle. The structure of a slotting nozzle comprises total length
L0, outlet diameter
D, stable segment length
L, convergent angle
θ, and straight segment length
l.
According to calculations using a 75 mm drill pipe commonly used in coal mines, the maximum length of the slotting nozzle is 26 mm. At present, the rating of high-pressure pumps commonly used in coal mines is 31.5 MPa, the flow rate is 200 L/min, and so the diameter of the slotting nozzle outlet was determined to be 3 mm. Hence, the three factors that affect the performance of slotting nozzle are stable segment length L, convergent angle θ, and straight segment length l. Reasonable values of these three factors will influence the slotting ability.
2.2. Design of Slotting Nozzle Structural Parameters Orthogonal Optimization
Orthogonal design is a scientific method used to select a suitable number of representative experimental points from a large number of experimental points according to the principle of mathematical statistics, and to rationally arrange multi-factor experiments using a standardized “orthogonal table”. The above analysis showed that the performance of a slotting nozzle is mainly related to stable segment length
L, convergent angle
θ, and straight segment length
l. Each factor was considered at four levels in the appropriate ranges for these three factors. According to the selected model of three factors and four levels, an orthogonal table was selected to include sixteen numerical experiments, as shown in
Table 1.
A slotting nozzle suitable for coal-seam slotting conditions requires not only good convergence of the water jet, but also higher velocity and striking force of the jet for the same target distance. The striking force of a water jet on a target is directly related to its dynamic pressure (pk). The dynamic pressure of a water jet is proportional to the jet velocity, so we used dynamic pressure as the evaluation index. The performances of 16 different types of slotting nozzles were compared by investigating the water jet dynamic pressure under the same working pressure: specifically, the axial dynamic pressure (pk1) and longitudinal profile dynamic pressure (pk2) of the water jet were evaluated at a distance of 150 mm from the slotting nozzle outlet.
2.3. Numerical Experiments to Optimize Slotting Nozzle Index
Numerical simulation of the performances of the slotting nozzles was carried out using CFD modeling. Each slotting nozzle was installed vertically on the slotting device, within which there was high-speed turbulent flow. The control equation therefore comprised equations of continuity, the Navier–Stokes equation, and realizable
k–ε equations. The geometric model was relatively small; therefore, quadrilateral mesh generation was used to generate the meshes of the inner and outer flow fields. The grid spacing was 0.5 mm. The geometric model of the slotting nozzle flow field is shown in
Figure 2.
The finite-volume method was used to disperse the control equation; simple algorithms were used to couple the pressure and velocity. The fluid was assumed to be ideal, that is, the flow was steady, and gravity and cavitation were not be taken into consideration. The boundary conditions are shown in
Table 2.
In the process of optimizing the slotting nozzle structural parameters, a submerged water jet was used to simulate the inner and outer flow fields. Since the submerged water jet had the characteristics of fast attenuation, using a smaller model to simulate the slotting nozzle outflow could clearly distinguish the advantages and disadvantages of the structure and save calculation time. The numerical simulation results of Experiment 1 are shown in
Figure 3.
Figure 3 shows that the high-pressure water underwent acceleration inside the slotting nozzle, and the dynamic pressure gradually increased in this section; however, the dynamic pressure on the section did not change uniformly. In particular, in the area between the bend of the flow channel and the convergent section, the distribution of the slotting dynamic pressure was greatly influenced by the structure of the flow channel. At the turning point of the main channel of the slotting device into the slotting nozzle, the dynamic pressure distribution was larger in the upper part of the nozzle axis, but smaller in the lower part. When high-pressure water entered the stable section of the slotting nozzle, the distribution of dynamic pressure was high in the middle and low on both sides of the same cross-section. An obvious low-pressure zone formed near the inner wall of the slotting nozzle. The non-uniform distribution of the dynamic pressure inside the slotting nozzle created conditions for the generation of vortices and flow recirculation. The formation of a large number of vortices and recirculation greatly reduce the quality of the water jet.
Based on simulated data of internal and external flow fields of sixteen different slotting nozzles, the axial and longitudinal dynamic pressure curves of the water jet at a distance of 150 mm from the slotting nozzle outlet were plotted, as shown in
Figure 4.
The curves of
Figure 4a show that with an increase of the abscissa, the dynamic pressure gradually decreased and its rate of change gradually decreased. Slotting nozzles with different structural parameters had different outlet dynamic pressures for the same pressure source. The type 0-30-9 slotting nozzle (stable segment length
L = 0 mm, convergent angle
θ = 30°, and straight segment length
l = 9 mm) had the best performance. Not only was the outlet dynamic pressure larger than those of other slotting nozzles, but the attenuation of the axial pressure was slower. Slotting nozzle type 9-10-12 had the worst performance.
Figure 4b presents longitudinal profiles of the dynamic pressures of the sixteen different types of slotting nozzles at a distance of 150 mm from the slotting nozzle outlet under submerged conditions. The maximum dynamic pressure at the slotting nozzle axis gradually decreased with increase of the distance from the axis to both sides, and the rate of change gradually decreased. Slotting nozzles with different structural parameters had different dynamic pressures at the outlet of the slotting nozzle under the same pressure source: the difference was most obvious at the axis. The above optimization results showed that the slotting nozzle with structural parameters of 0-30-9 had the best performance.
2.4. Numerical Experiment Results and Discussion
The performance of a slotting nozzle is mainly related to stable segment length
L, convergent angle
θ, and straight segment length
l. To evaluate the influence of each parameter on its performance and to provide a basis for the processing accuracy of each parameter, the significance of each parameter was analyzed. The results are shown in
Table 3.
As seen from
Table 3, the convergent angle
θ had the largest range; the ranges of the stable segment length
L and straight segment length
l were similar. The data show that the convergent angle
θ had the greatest influence on slotting nozzle performance, while the influences of stable segment length
L and straight segment length
l were small. According to the magnitude of range, the primary and secondary orders of parameters affecting nozzle performance are: nozzle convergent angle
θ > stable segment length
L > straight segment length
l.
Taking the influencing factors as the abscissa and the water jet pressure at a distance of 150 mm from the outlet as the ordinate, the trends of slotting nozzle structure parameters and performance were plotted, as shown in
Figure 5.
When the total length of the slotting nozzle was fixed, the dynamic pressure gradually decreased and the rate of decrease slowed down with an increase of the length of the stable section L. With an increase of convergent angle θ, the dynamic pressure increased quadratically and the rate of change gradually decreased. With an increase of straight segment length l, the dynamic pressure decreased quadratically and the rate of change gradually increased.