1. Introduction
The existence of tau-neutrino was predicted in 1975 after the discovery of tau lepton [
1]. In 2000, tau-neutrino charged-current (CC) interactions were observed by the DONuT experiment [
2]. However, the first tau-neutrino interaction cross section measurement was performed with more than 50% systematic and 33% statistical uncertainties, due to the uncertainty in the tau-neutrino flux and the low statistics [
3].
DsTau experiment proposes to study the tau-neutrino production and to improve the calculation of tau neutrino flux in the DONuT experiment to 10% level. Moreover, with the help of DsTau results, in future neutrino experiments like SHiP [
4], where
tau neutrinos interactions are expected, from about
and
to be produced by
protons on target, both uncertainties in tau-neutrino interaction cross-section will be greatly reduced [
5,
6], making possible to the test of the Lepton Universality hypothesis.
The principal source of tau-neutrino is the leptonic decay of Ds meson [
3]. The Ds to tau decay has a peculiar topology, and can be recognised in 400 GeV proton interaction with a Tungsten target (
Figure 1). There are 1000 Ds-tau events expected from
proton interactions, from a total initial flux of
protons in the DsTau experiment [
5].
2. Materials and Methods
The Ds to tau events will be recognised by their double-kink topology [
5], taking advantage of the best spatial resolution of the emulsion detectors. The detector module structure, as presented in
Figure 2, is composed of 10 Tungsten targets. In total, 10 double-side emulsion plates on plastic support, separated by plastic plates, are inserted between two targets. At the end, an Emulsion Cloud Chamber (ECC) part is attached, composed of 26 double-side emulsion plates intercalated by Lead plates. The purpose of the ECC part is to measure the momenta of high energy particles. The proton beam is perpendicular to the detector module [
5,
6].
The module dimensions are
. The experiment will use in total 370 modules, containing more than 48,000 emulsion plates which have to be produced before the experiment and chemically processed after the exposure. The data readout (scanning process) is automatic, using the Hyper Track Selector (HTS) which could scan a plate in 5 min [
5]. After the scanning process, the information on all particle tracks will become available.
A module is positioned on a target mover as presented in the
Figure 2, whose purpose is to change the position of the module in front of the proton beam, assuring the uniformity of the irradiation. Additional telescopes of pixel detectors could be added in the scope of evaluating the proton beam (
Figure 2).
3. Results
The primary purpose of the analysis of the pilot run was to study the feasibility of the experiment. It was important to compare the experimentally observed characteristics expected from simulation. Here we present particular results for a study of multiplicity of secondary charged particles in proton interactions with different materials in detector.
The automatic data readout is followed by a geometrical reconstruction of tracks and vertexes of the proton interactions. When a vertex is found, it could be correlated with a parental proton track. In the performed preliminary analysis, only the vertexes with parent (named primary proton interactions [
5]) are considered.
The vertexes distribution in the detector module is presented in
Figure 3. The sub-sample of the detector structure taken into consideration is composed of one Tungsten plate and four double-side emulsion plates, together with the plastic separators and one side emulsion layer on the edges. The Tungsten plate is clearly distinguished from the other layers in terms of amount of primary proton interactions.
The distribution in
Figure 3 is useful for distinguishing the interactions in each material. The delimitation used in the analysis is showed by colors. The grey corresponds to the cuts applied for the Tungsten plate, and the green to the cuts applied for the plastic layers. The blue corresponds to the cuts applied for the emulsion layers.
In
Figure 4 the Monte Carlo (MC) comparison with the data for the multiplicity distributions in each structural material is presented. Only the charged daughters were considered from the regions indicated in the
Figure 3. The MC predictions were performed by FLUKA and scaled to the number of entries in data. Further study will be done on the number of proton interactions.
In
Figure 5 are presented the comparisons between the multiplicities in the three materials, for MC predictions and for the data. All the distributions were normalized to unity.
4. Conclusions and Outlook
The DsTau experiment studies tau neutrino production in high energy proton interactions, which will provide the needed information for the future tau-neutrino experiments [
5].
For the pilot run, the emulsion scanning as well as the analysis of the samples is an ongoing work, which will provide data for optimisation of the experiment in the main run in 2021–2022.