Magnetism, Volume 1, Issue 1 (December 2021) – 6 articles

In this paper, a unique approach to the imaging of non-metallic media using capacitive sensing is presented. By using customized sensor plates in single-ended and differential configurations, responses to hidden objects can be captured over a cylindrical aperture surrounding the inspected medium. Then, by processing the acquired data using a novel imaging technique based on the convolution theory, Fourier and inverse Fourier transforms, and exact low resolution electromagnetic tomography (eLORETA), images are reconstructed over multiple radial depths using the acquired sensor data. Imaging hidden objects over multiple depths has wide range of applications, from biomedical imaging to nondestructive testing of the materials. Performance of the proposed imaging technique is demonstrated via experimental results. Full article

Polymer bonded magnets based on thermoplastics are economically produced by the injection molding process for applications in sensor and drive technology. Especially the lack of orientation in the edge layer, as well as the chemical resistance and the creep behavior limit the possible implementations of thermoplastic based polymer bonded magnets. However, thermoset based polymer bonded magnets have the opportunity to expand the applications by complying with the demands of the chemical industry or pump systems through to improved chemical and thermal resistance, viscosity and creep behavior of thermosets. This paper investigates the influence of hard magnetic particles on the flow and curing behavior of highly filled thermoset compounds based on an epoxy resin. The basic understanding of the behavior of those highly filled hard magnetic thermoset systems is essential for the fabrication of polymer bonded magnets based on thermosets in the injection molding process. It is shown that several factors like the crystal structure, the particle shape and size, as well as the thermal conductivity and the adherence between filler and matrix influence the flow and curing behavior of highly filled thermoset compounds based on epoxy resin. However, these influencing factors can be applied to any filler system with respect to a high filler amount in a thermoset compound, as they are based on the material behavior of particles. Further, the impact of the flow and curing behavior on the magnetic properties of polymer bonded magnets based on thermosets is shown. With that, the correlation between material based factors and magnetic properties within thermosets are portrayed. Full article

Ferroelectric samples Sr_1−xBa_xTiO₃ (BST), where x = 0, 0.2, 0.4, 0.6, 0.8 and 1, were prepared using the tartrate precursor method and annealed at 1200 °C for 2 h. X-ray diffraction, “XRD”, pattern analysis verified the structure phase. The crystallite size of the SrTiO₃ phase was calculated to be 83.6 nm, and for the TiO₂ phase it was 72.25 nm. The TEM images showed that the crystallites were agglomerated, due to their nanosize nature. The AC resistivity was measured as temperature dependence with different frequencies 1 kHz and 10 kHz. The resistivity was decreased by raising the frequency. The dielectric properties were measured as the temperature dependence at two frequencies, 1 kHz and 10 kHz. The maximum amount of dielectric constant corresponded to the Curie temperature and the transformation from ferroelectric to paraelectric at 1 kHz was sharp at 10 kHz. Polarization–electric field hysteresis loops for BST samples were measured using a Sawer–Tawer modified circuit. It was shown that the polarization decreased with increasing temperature for all samples. Full article

Due to lower magnetic properties of polymer-bonded magnets compared to sintered magnets, a complete redesign of the multipolar soft magnetic flux barriers in rotors with alignment guidelines was carried out to eliminate the frequently used rare-earth magnets, causing a new influence of the outer magnetic field on the cavity by using soft magnetic inserts. Within this new process, the main influencing factors on the magnetic flux density such as filler content, tool temperature, holding pressure and injection velocity were analysed and correlated. The studies were based on the compound of Polyamide 12 and up to a 60 vol.-% of the hard magnetic filler, strontium ferrite. Based on the study, the injection moulding of multipolar-bonded magnets into soft magnetic inserts for rotors and, in turn, into complex geometries can be optimized in terms of the orientation of the filler, the microstructure and the magnetic flux density. The investigations show no significant influence of the process parameters known from the literature such as the mass temperature T_m, which affects the magnetic flux density, as well as the orientation and the microstructure similar to tool temperature Tt, but is less efficient. The main influencing factors identified during the investigations are the tool temperature Tt, the injection velocity v_in and the holding pressure p_h. As known influencing factors are only based on simple geometries such as ring structures or plates, new factors were determined for complex rotor geometries. Full article