Search Results (74)

With increasing natural gas processing demands, triethylene glycol (TEG) in dehydration systems becomes contaminated by gas-carried impurities, leading to problematic foaming, degradation, and significant glycol losses that compromise operational economics, pipeline integrity, and product quality. To systematically investigate impurity effects, we conducted comprehensive single-factor TEG regeneration experiments simulating field conditions. Through precise measurements of foaming height, defoaming time, and interfacial tension, we established clear correlations between impurity types and TEG foaming characteristics. Our results demonstrate a distinct hierarchy of foaming influence: chemical additives > solid impurities > water-soluble inorganic salts > MDEA > hydrogen sulfide > hydrocarbons. Chemical additives showed the most pronounced effect on surface tension, reducing it to 31.1 mN/m at 1500 mg/L. Water-soluble inorganic salts affected foaming through combined decomposition and crystalline morphology effects, ranked as MgCl₂ > NaHCO₃ > KCl > NaCl > Na₂SO₄ > CaCl₂ (MgCl₂ achieving 33.8 mN/m at 2000 mg/L). Solid impurity impacts correlated strongly with particle morphology (CaCO₃ > Fe₂O₃ > CaSO₄ > ZnO > CuO > Al₂O₃ > FeS), stabilizing at 1.5 mg/L. Hydrocarbons showed negligible influence, while hydrogen sulfide and MDEA caused only minor surface tension reductions with limited foaming effects. Based on these findings, we propose targeted mitigation strategies for industrial implementation. Full article

Tattoo inks contain varying amounts of metal nanoparticles (NPs) < 100 nm that, due to their unique physicochemical properties, may have specific biological uptake and cause skin or systemic toxicities. The toxic effects of certified reference standards of metal NPs and samples of commercially available tattoo inks were investigated using an in vitro system and a novel human ex vivo model. In vitro toxicity was evaluated using vitality assays on human skin cells (HaCaT cell line, primary fibroblasts, and keratinocytes). No toxicity was observed for Al₂O₃, Cr₂O₃, Fe₂O₃, and TiO₂ NPs, whereas CuO NPs showed dose-dependent toxicity on HaCaT and primary fibroblasts. Fibroblasts and keratinocytes were also sensitive to high concentrations of ZnO NPs. Reference standards and ink samples were then injected ex vivo into human skin explants using tattoo needles. Histological analysis showed pigment distribution deep in the dermis and close to dermal vessels, suggesting possible systemic diffusion. The presence of an inflammatory infiltrate was also observed. Immunohistochemical analysis showed increased apoptosis and expression of the inflammatory cytokine interleukin-8 in explants specifically tattooed with the reference standard or red ink. Taken together, the results suggest that the tattooing technique leads to exposure to toxic metal NPs and skin damage. Full article

Bulgarian wines are renowned worldwide and serve as a symbol of the country. However, ensuring wine authenticity and establishing reliable methods for its assessment are critical challenges in wine quality control. This study investigates the migration of chemical elements within the soil/grape/wine system and utilizes the findings to develop a method for identifying specific elements capable of distinguishing the geographical origin of wine. Additionally, it explores the potential to determine its botanical origin. Thirty monovarietal Bulgarian wines, specifically produced for this study with precisely known geographical and botanical origins, were analyzed for 20 chemical elements. These included macroelements such as Al, B, Ba, Ca, Cu, Fe, K, Mg, Mn, Na, P, Sr, and Zn, as well as microelements like As, Cd, Co, Cr, Li, Ni, and Pb. The study encompassed white wines from Chardonnay, Muscat Ottonel, Sauvignon Blanc, Tamyanka, and Viognier varieties, as well as red wines from Egiodola, Broad-Leaved Melnik, Cabernet, Cabernet Franc, Cabernet Sauvignon, Marselan, Melnik, Merlot, Pinot Noir, and Syrah. The chemical composition was determined in soil extracts (using acetate and EDTA extract to represent the bioavailable fraction), vine leaves, primary musts, and raw wines before clarification and stabilization. Statistically significant correlation coefficients were calculated for the soil/leaves, soil/must, and must/wine systems, enabling an analysis of the migration of chemical elements from soil to wine and the concentration changes throughout the process. The results identified elemental descriptors capable of indicating the geographical origin of wine. Full article

Traditional mining activities in Zaruma-Portovelo (SE Ecuador) have led to high concentrations of pollutants in the Puyango River due to acid mine drainage (AMD) from abandoned waste. Dispersed alkaline substrate (DAS) passive treatment systems have shown efficacy in neutralizing acidity and retaining metals and sulfates in acidic waters, achieving near a 100% retention for Fe, Al, and Cu, over 70% for trace elements, and 25% for SO₄²⁻. However, significant solid residues are generated, requiring proper geochemical and mineralogical understanding for management. This study investigates the fractionation of elements in AMD precipitates. Results indicate that Fe³⁺ and Al³⁺ predominantly precipitate as low-crystallinity oxyhydroxysulfate minerals such as schwertmannite [Fe³⁺₁₆(OHSO₄)_12–13O₁₆·10–12H₂O] and jarosite [KFe³⁺₃(SO₄)₂(OH)₆], which retain elements like As, Cr, Cu, Pb, and Zn through adsorption and co-precipitation processes. Sulfate removal occurs via salts like coquimbite [AlFe₃(SO₄)₆(H₂O)₁₂·6H₂O] and gypsum [CaSO₄·2H₂O]. Divalent metals are primarily removed through carbonate and bicarbonate phases, with minerals such as azurite [Cu(OH)₂·2CuCO₃], malachite [Cu₂(CO₃)(OH)₂], rhodochrosite [MnCO₃], and calcite [CaCO₃]. Despite the effectiveness of DAS, leachates from the precipitates exceed regulatory thresholds for aquatic life protection, classifying them as hazardous and posing environmental risks. However, these residues offer opportunities for the recovery of valuable metals. Full article

Different mixed cultures of extremely thermoacidophilic microorganisms were used for bioleaching of metalliferous industrial dust waste derived from the basic oxygen furnace (BOF) steelmaking process. Such mixed cultures can extract various metals from multi-metallic BOF-dust waste, improving the metal dissolution and bioleaching performance in frames of metal recycling processes to assist circular economies and waste management. The results of the investigation showed that mixed cultures of thermoacidophilic archaea of the order Sulfolobales (Acidianus spp., Sulfolobus spp., and Metallosphaera sedula) during their growth in laboratory glass bioreactors provided a superior bioleaching system to Acidianus manzaensis alone. Depending on the composition of mixed thermoacidophilic cultures, extraction of various metals from BOF-dust could be achieved. Among the three different types of mixed cultures tested, the mixed culture system of A. manzaensis, A. brierleyi, and S. acidocaldarius was most effective for extraction of major elements (Fe, Ca, Zn, Mn, and Al). The mixed culture of A. manzaensis, A. brierleyi, and M. sedula showed high performance for bioleaching of most of the minor elements (Cu, Ni, Pb, Co, Mo, and Sr). The efficient ability of mixed cultures to colonise the mineral matrix of the metal waste product was observed via scanning electron microscopy, while their metal extraction capacities were analysed by inductively coupled plasma mass spectrometry. These investigations will promote the further design of microbial consortia in order to break down the solid matrix and efficiently extract metals from metalliferous waste materials. Full article

A series of M(x)CoCeMgAlO mixed oxides with different transition metals (M = Cu, Fe, Mn, and Ni) with an M content x = 3 at. %, and another series of Fe(x)CoCeMgAlO mixed oxides with Fe contents x ranging from 1 to 9 at. % with respect to cations, while keeping constant in both cases 40 at. % Co, 10 at. % Ce and Mg/Al atomic ratio of 3 were prepared via thermal decomposition at 750 °C in air of their corresponding layered double hydroxide (LDH) precursors obtained by coprecipitation. They were tested in a fixed bed reactor for complete methane oxidation with a gas feed of 1 vol.% methane in air to evaluate their catalytic performance. The physico-structural properties of the mixed oxide samples were investigated with several techniques, such as powder X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDX), elemental mappings, inductively coupled plasma optical emission spectroscopy (ICP-OES), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction under hydrogen (H₂-TPR) and nitrogen adsorption–desorption at −196 °C. XRD analysis revealed in all the samples the presence of Co₃O₄ crystallites together with periclase-like and CeO₂ phases, with no separate M-based oxide phase. All the cations were distributed homogeneously, as suggested by EDX measurements and elemental mappings of the samples. The metal contents, determined by EDX and ICP-OES, were in accordance with the theoretical values set for the catalysts’ preparation. The redox properties studied by H₂-TPR, along with the surface composition determined by XPS, provided information to elucidate the catalytic combustion properties of the studied mixed oxide materials. The methane combustion tests showed that all the M-promoted CoCeMgAlO mixed oxides were more active than the M-free counterpart, the highest promoting effect being observed for Fe as the doping transition metal. The Fe(x)CoCeMgAlO mixed oxide sample, with x = 3 at. % Fe displayed the highest catalytic activity for methane combustion with a temperature corresponding to 50% methane conversion, T₅₀, of 489 °C, which is ca. 40 °C lower than that of the unpromoted catalyst. This was attributed to its superior redox properties and lowest activation energy among the studied catalysts, likely due to a Fe–Co–Ce synergistic interaction. In addition, long-term tests of Fe(3)CoCeMgAlO mixed oxide were performed, showing good stability over 60 h on-stream. On the other hand, the addition of water vapors in the feed led to textural and structural changes in the Fe(3)CoCeMgAlO system, affecting its catalytic performance in methane complete oxidation. At the same time, the catalyst showed relatively good recovery of its catalytic activity as soon as the water vapors were removed from the feed. Full article

In this study, the thermodynamic simulation model and system of the copper side-blown smelting process were established using the chemical equilibrium constant method, based on the process reaction mechanism, multiphase equilibrium principle, and MetCal software platform (MetCal v7.81). Under typical production conditions, the composition of the product and the distribution behavior of impurity elements were simulated. The results indicate that the average relative error between the calculated mass fractions of major elements such as Cu, S, Fe, SiO₂, CaO, MgO, and Al₂O₃ in copper matte and smelting slag, and the actual production values, is 4.25%. Additionally, the average relative error between the calculated distribution ratios of impurity elements such as Pb, Zn, As, Bi, Mo, Au, and Ag in copper matte and smelting slag, and the actual production data, is 6.74%. Therefore, this model and calculation system accurately reflects the actual production situation of the copper side-blown smelting process well and has potential to predict process output accurately while optimizing process parameters, effectively guiding production practice. Full article

Printed circuit boards (PCBs) are the main components of e-waste. In order to reduce the negative impact of waste PCBs on human health and the environment, they must be properly disposed of. A new method is demonstrated for recycling waste PCBs. It is referred to as the high-temperature thermo-mechano-chemical gasification (TMCG) of PCBs by the detonation-born gasification agent (GA), which is a blend of H₂O and CO₂ heated to a temperature above 2000 °C. The GA is produced in a pulsed detonation gun (PDG) operating on a near-stoichiometric methane–oxygen mixture. The PDG operates in a pulsed mode producing pulsed supersonic jets of GA and pulsed shock waves possessing a huge destructive power. When the PDG is attached to a compact flow reactor filled with waste PCBs, the PCBs are subject to the intense thermo-mechano-chemical action of both strong shock waves and high-temperature supersonic jets of GA in powerful vortical structures established in the flow reactor. The shock waves grind waste PCBs into fine particles, which undergo repeated involvement and gasification in the high-temperature vortical structures of the GA. Demonstration experiments show full (above 98%) gasification of the 1 kg batch of organic matter in a setup operation time of less than 350 s. The gaseous products of PCB gasification are mainly composed of CO₂, CO, H₂, N₂, and CH₄, with the share of flammable gas components reaching about 45 vol%. The solid residues appear in the form of fine powder with visible metal inclusions of different sizes. All particles in the powder freed from the visible metal inclusions possess a size less than 300–400 μm, including a large fraction of sizes less than 100 μm. The powder contains Sn, Pb, Cu, Ni, Fe, In, Cd, Zn, Ca, Si, Al, Ti, Ni, and Cl. Among these substances, Sn (10–20 wt%), Pb (5–10 wt%), and Cu (up to 1.5 wt%) are detected in the maximum amounts. In the powder submitted for analysis, precious elements Ag, Au, and Pt are not detected. Some solid mass (about 20 wt% of the processed PCBs) is removed from the flow reactor with the escaping gas and is partly (about 10 wt%) trapped by the cyclones in the exhaust cleaning system. Metal inclusions of all visible sizes accumulate only in the flow reactor and are not detected in powder samples extracted from the cyclones. The gasification degree of the solid residues extracted from the cyclones ranges from 76 to 91 wt%, i.e., they are gasified only partly. This problem will be eliminated in future work. Full article

Chalkbrood is a disease of honey bee brood caused by the fungal parasite Ascosphaera apis. Many factors such as genetics, temperature, humidity and nutrition influence the appearance of clinical symptoms. Poor nutrition impairs the immune system, which favors the manifestation of symptoms of many honey bee diseases. However, a direct link between dietary ingredients and the symptoms of chalkbrood disease has not yet been established. We show here that the elemental composition of chalkbrood mummies and healthy larvae from the same infected hives differ, as well as that mummies differ from larvae from healthy hives. Chalkbrood mummies had the highest concentration of macroelements such as Na, Mg, P, S, K and Ca and some microelements such as Rb and Sn, and at the same time the lowest concentration of B, As, Sr, Ag, Cd, Sb, Ba and Pb. Larvae from infected hives contained less Pb, Ba, Cs, Sb, Cd, Sr, As, Zn, Cu, Ni, Co, Mn, Cr, V and Al in contrast to healthy larvae from a disease-free apiary. This is the first study to demonstrate such differences, suggesting that an infection alters the larval nutrition or that nutrition is a predisposition for the outbreak of a chalkbrood infection. Though, based on results obtained from a case study, rather than from a controlled experiment, our findings stress the differences in elements of healthy versus diseased honey bee larvae. Full article

The present work was carried out to obtain and highlight the fifth comprehensive baseline dataset on atmospheric deposition of trace elements and to assess air quality in Macedonia. In the period from August to September 2020, a total of 72 moss samples were collected in accessible areas in the country. The content of 28 elements (Ag, Al, B, Ba, Ca, Cd, Co, Cr, Cu, Fe, Ga, Hg, K, La, Mg, Mn, Mo, Na, Ni, P, Pb, S, Sb, Sc, Sr, Ti, U, and Zn) was determined using inductively coupled plasma–mass spectrometry. Based on the data obtained on the content of the elements, a factor analysis was carried out to identify and characterise different sources of pollution. In addition, distribution maps were created for all elements to show the regions most affected by anthropogenic activities. The survey conducted in 2020 has shown that air pollution with potentially toxic elements (PTEs) has slightly decreased compared to the results of the previous survey from 2015. This is due to the fact that, despite the operation of all mining and smelting facilities with the same capacity, government regulations for the installation of cleaning systems and additional regulations to reduce pollution have been introduced in the last five years. Nevertheless, the fact remains that the highest anthropogenic air pollution with PTEs is still caused by the operation of the ferronickel smelter in Kavadarci (Ni and Cr) in the southern part and by the lead and zinc mines in Probištip, Makedonska Kamenica, and Kriva Palanka in the eastern part of the country (Cd, Pb, and Zn). Full article

Pyrometallurgy is the primary technique for the production of many nonferrous metals such as copper, lead, and zinc. The phase equilibrium information of smelting slags plays an important role in the efficient extraction of metals and energy consumption. The experimental technologies used in phase equilibrium studies are compared. The presentation and applications of the pseudo-ternary and pseudo-binary phase diagrams are demonstrated in the Fe–Si–Ca–Zn–Mg–Al–Cu–S–O system. Experimental results are also compared with the predictions of FactSage to evaluate the accuracy of the current thermodynamic database. This review paper provides comprehensive information for the operation of nonferrous metals and optimization of the thermodynamic database. Full article

Studies on the mineral and vitamin C contents of different species and ripening stages of Solanum fruits are very limited. The aim of the research was to evaluate the content of the mineral elements and vitamin C of four different Solanum species (S. melanocerasum—SM, S. nigrum—SN, S. villosum—SV and S. retroflexum—SR), and three ripening stages. The mineral composition of Solanum fruits was detected using a CEM MARS 6^® (Matthews, NC, USA) digestion system outfitted with a 100 mL Teflon vessel, by microwave-assisted extraction (MAE). In total, eleven mineral elements were detected (K, Ca, Mg, P, Fe, Na, Cu, B, Mn, Al, and Zn). Vitamin C content was assessed by a spectrophotometric method. Depending on the ripening stage/species, content of microelements ranged from 756.48 mg kg⁻¹ DW in SV fruits at ripening stage III, to 211.12 mg kg⁻¹ DW in SM fruits at ripening stage III. The dominant microelement was Fe. The total content of macroelements in Solanum fruits ranged from 26,104.95 mg kg⁻¹ DW in SV fruits at ripening stage II to 67,035.23 mg kg⁻¹ DW in SR fruits at ripening stage I. The dominant macroelement was K. The data from two experimental years showed that the significantly highest content of vitamin C was in SM fruits and ranged from 48.15 mg 100 g⁻¹ at ripening stage I to 45.10 mg 100 g⁻¹ at ripening stage III. Full article

The Irkutsk Reservoir, belonging to the largest unified freshwater Baikal–Angara system, is an important source of drinking water in the region. Therefore, studies of its hydrochemical characteristics are of prime importance in deciding on the role of anthropogenic activity in water quality. The water samples were collected across the reservoir in 2007, 2012, and 2021 and then were analyzed for major ions and trace elements. The data revealed that the distribution of HCO₃⁻, SO₄²⁻, Cl⁻, Ca²⁺, Mg²⁺, Na⁺ and K⁺ is stable across the reservoir. Trace element concentrations varied from 1.13 to 15.39 µg L⁻¹ for Al, from <DL to 0.39 µg L⁻¹ for Cr, from 0.39 to 23.12 µg L⁻¹ for Mn, from 1.25 to 53.22 µg L⁻¹ for Fe, from 0.005 to 0.100 µg L⁻¹ for Co, from 0.20 to 1.98 µg L⁻¹ for Cu, from <DL to 13.40 µg L⁻¹ for Zn, from 0.25 to 0.48 µg L⁻¹ for As, from 0.004 to 0.127 µg L⁻¹ for Cd, from <DL to 0.195 µg L⁻¹ for Sn, from <DL to 0.0277 µg L⁻¹ for Cs, from <DL to 1.13 µg L⁻¹ for Pb, from <DL to 0.0202 µg L⁻¹ for Th, and from 0.27 to 0.75 µg L⁻¹ for U. The concentrations of all major ions and trace elements in water were below the drinking water standards. CF values showed considerable and high contamination of samples with Al, Mn, Fe, Co, Cu, Cd, Sn, Pb, and Th. PLI values classified the majority of water samples as water with baseline levels of pollutants, and part of the samples was classified as either polluted or highly polluted. Full article

The qualitative X-ray phase analysis of natural and artificial food sweeteners was applied to trace the authenticity of such food additives. The mineral composition of different sweeteners commonly added to foods was studied to estimate their mineral profiles and assess the risk related to the toxic elements intake caused by sweetener consumption. The concentration of twenty elements (Ag, Al, B, Ba, Bi, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, Sr, Ti, V, and Zn) was measured using the inductively coupled plasma–optical emission spectroscopy (ICP-OES) method after the representative samples were wet-digested with a concentrated nitric acid and hydrogen peroxide mixture in a closed-vessel microwave-assisted system. Differences between the mineral compositions of the examined sweeteners were statistically evaluated and discussed. The relationships between the concentrations of the elements determined in the analyzed sweeteners were also investigated. The successful application of the X-ray powder diffraction method proved the identity of all investigated sweeteners; all the analyzed products contained the expected sweetening agent. The results of the quantification of all the elements in the examined sweeteners indicated that these products cannot be considered nutritionally dense. Hence, the presence of toxic elements like Cd, Cr, Ni, and Pb distinctly indicates the need to test such products to guarantee their quality and ensure consumer safety. Full article

Although rice is a well-known source of nutrients, it unfortunately accumulates As the most compared to other cereal plants. Due to the growing interest in rice-based cosmetics, the aim of the work was the multi-element analysis of various home-made (natural) rice waters and commercialized ready-to-use rice-based cosmetics for skin/hair. The total concentrations of Al, As Ca, Cd, Cr, Cu, Fe, Mg, Mn, Ni, Pb, and Zn in raw rice and rice products were determined using inductively coupled optical emission spectrometry (ICP OES) after wet sample decomposition in the presence of concentrated HNO₃. In the case of As, the hydride generation (HG) technique was used as a sample introduction system to the ICP OES instrument. Five different procedures, including washing/rinsing, soaking, boiling, and fermentation steps, and three rice types, i.e., white, brow, and jasmine, were used for this purpose. The effects of the water temperature, the contact time of rice grains with water, and the type of rice on the water-soluble concentrations of elements were examined and compared. A significant difference in the solubility of elements was observed depending on the type of rice, with the lowest percentage of extraction noted for brown rice. The best option was soaking unwashed rice grains in a six-fold excess of cold water for 30 min. The selection criterion was to preserve the highest content of essential elements (Ca (0.76–1.2 mg kg⁻¹), Cu (9.2–43 ng k⁻¹), Fe (0.096–0.30 mg kg⁻¹), Mg (6.9–11 mg kg⁻¹), Mn (0.16–10.32 mg kg⁻¹), and Zn (0.083–0.25 mg kg⁻¹)) with reduced to a minimum As level, i.e., <5 ng g⁻¹ (2.8–4.8 ng g⁻¹), making this water safe for consumption. In contrast, regularly drinking water after boiling or soaking rice grains in hot water carries the risk of consuming an excessive amount of this element due to As content exceeding the permissible value, i.e., 10 ppb. Finally, these home-made products were compared with commercialized cosmetics for skin/hair, with satisfactory results. Full article