Search Results (106)

High-speed laser cladding (HLC) technology can provide high cooling rates and low dilution rates for the preparation of metastable Fe-based amorphous phases. In this work, the effects of Ta content on the microstructure, mechanical properties, and soft magnetic performance of Fe-based amorphous alloys were systematically investigated. The results indicated that Ta remained uniformly dispersed within the FeSiB amorphous powder, and no new phases were formed after mechanical ball milling. The higher mixing enthalpy of Ta and its atomic radius difference from other elements (such as Fe, Si, B) were beneficial in improving glass-forming ability (GFA), and with an increase in Ta element content from 0% to 2%, 4% and 6%, the amorphous phase content was 48.6%, 51.5%, 60.4% and 54.8%, respectively. The average microhardness of the coating with a Ta content of 4% was 1310 HV_0.2, which was 50HV_0.2 higher than before; in addition, the wear rate reduced from 2.21 × 10⁻⁴ mg·N⁻¹·m⁻¹ to 2.06 × 10⁻⁴ mg·N⁻¹·m⁻¹. Also, corrosion tests showed that the coating with a Ta content of 4% displayed superior corrosion resistance compared to that before the Ta addition. However, because the element Ta could alter the local electronic environment and enhance the local magnetic anisotropy of FeSiB, the saturation magnetic flux density (Ms) decreased from 1.64 T to 1.56 T, and the coercivity (Hc) increased from 0.9 A/m to 1.3 A/m, which caused degradation of the soft magnetic properties. Full article

Hybrid atomization represents a novel method for powder production with high cooling and crushing capacities, but previous studies have primarily focused on tin and aluminum alloy systems. In present study, FeSiBNbCu nanocrystalline powders were prepared using a hybrid atomization system and the effects of atomization parameters on the sphericity of the powders and soft magnetic properties of the nanocrystalline magnetic powder cores (NMPCs) were investigated. Orthogonal experiments reveal that atomization pressure is the most critical factor affecting powder size, while melting temperature primarily influences sphericity. By optimizing the atomization parameters, the nanocrystalline powders with a high sphericity of up to 91.2% can be achieved, and the core loss at 1 MHz@20 mT of the corresponding NMPCs is reduced by 59.2% to 464 mW/cm³. This study provides valuable guidance for the fabrication of Fe-based nanocrystalline powders with excellent soft magnetic properties via hybrid atomization. Full article

This study investigated the properties of a composite NiCrFeSiB coating with fine-dispersed WC additives, deposited by the HVOF method. The NiCrFeSiB powder alloy with WC additives was applied to a steel substrate. The WC content in the coating was 10, 15, and 20% by weight. The particle size distribution of the mixture ranged from 3 to 10 µm. The WC used was the WC8 alloy (92% WC, 8% Co). The levels of stress, phase composition, hardness, wear resistance, and coating structure were investigated. The studies revealed that the structure was primarily composed of the γ-Ni-Fe solid solution phase, with secondary phases including Ni₃B, Fe₃B, (Cr,)₂B, and carbides of the W₂C, WC, M₇C₃ type. A small amount of the initial WC particles was also present. The use of a fine-dispersed NiCrFeSiB powder mixture with WC particles resulted in a nearly twofold increase in hardness and wear resistance compared to the same parameters of the coating without WC. The coating with 20% WC exhibited the highest hardness. However, its wear resistance was lower than that of the coating with 15% WC. This fact could be explained by a slight difference in the phase composition and an increase in the proportion of the unsolidified WC phase in the structure. This led to the spalling of fine particles and a reduction in wear resistance. The study demonstrated the feasibility of using a fine-dispersed NiCrFeSiB coating with WC additives without additional remelting. Similar hardness and wear resistance results were achieved immediately after HVOF spraying when using a fine-dispersed NiCrFeSiB + 15% WC/Co mixture with a 92/8 composition. This simplification of the technology reduced the coating application process time. It also lowered production costs by eliminating the remelting stage. Full article

In this study, regression-based machine learning models were developed to predict the melt pool width and depth formed during the Laser Powder Bed Fusion (LPBF) process for Fe-3.4Si and Fe-6Si alloys. Based on experimentally obtained melt pool width and depth data, a total of 11 regression models were trained and evaluated, and hyperparameters were optimized via Bayesian optimization. Key process parameters were identified through data preprocessing and feature engineering, and SHAP analysis confirmed that the input energy had the strongest influence on both melt pool width and depth. The comparison of prediction performance revealed that the support vector regressor with a linear kernel (SVR_lin) exhibited the best performance for predicting melt pool width, while the multilayer perceptron (MLP) model achieved the best results for predicting melt pool depth. Based on these trained models, a power–velocity (P-V) process map was constructed, incorporating boundary conditions such as the overlap ratio and the melt pool morphology. The optimal input energy range was derived as 0.45 to 0.60 J/mm, ensuring stable melt pool formation. Specimens manufactured under the derived conditions were analyzed using 3D X-ray CT, revealing porosity levels ranging from 0.29% to 2.89%. In particular, the lowest porosity was observed under conduction mode conditions when the melt pool depth was approximately 1.0 to 1.5 times the layer thickness. Conversely, porosity tended to increase in the transition mode and lack of fusion regions, consistent with the model predictions. Therefore, this study demonstrated that a machine learning-based regression model can reliably predict melt pool characteristics in the LPBF process of Fe-Si alloys, contributing to the development of process maps and optimization strategies. Full article

Titanium-based bulk metallic glasses (BMGs) offer high strength, lower stiffness than Ti-6Al-4V, and superior corrosion resistance, but conventional Ti glass-forming systems often contain toxic Ni, Be, or Cu. This work investigates five novel Ti-based alloys free of these elements—Ti₄₂Zr₃₅Si₅Co_12.5Sn_2.5Ta₃, Ti₄₂Zr₄₀Ta₃Si₁₅, Ti₆₀Nb₁₅Zr₁₀Si₁₅, Ti₃₉Zr₃₂Si₂₉, and Ti_65.5Fe_22.5Si₁₂—synthesized by arc melting and suction casting. Single-track laser remelting using a selective laser melting (SLM) system was performed to simulate additive manufacturing and examine microstructural evolution, cracking behavior, mechanical properties, and cytocompatibility. All alloys solidified into fully crystalline α/β-Ti matrices with Ti/Zr silicides; no amorphous structures were obtained. Laser remelting refined the microstructure but did not induce glass formation, consistent with the known limited glass-forming ability of Cu/Ni/Be-free Ti systems. Cracking was observed at low laser energies but crack density decreased as laser energy increased. Cracks were eliminated above ~0.4 J/mm for most alloys. Ti₄₂Zr₃₅Si₅Co_12.5Sn_2.5Ta₃ exhibited the lowest stiffness (~125 GPa), while Ti₆₀Nb₁₅Zr₁₀Si₁₅ showed the highest due to silicide precipitation. Cytotoxicity tests (ISO 10993-5) confirmed all alloys to be non-toxic, with some extracts even enhancing fibroblast proliferation. This rapid laser-remelting approach enables cost-effective screening of Ti-based glass-forming alloys for additive manufacturing. Ti–Zr–Ta–Si systems demonstrated the most promising properties for further testing using the powder bed method. Full article

Soft-magnetic materials can benefit significantly from additive manufacturing using Laser Powder Bed Fusion of metals with laser beam, as this technology allows the production of parts with complex geometries. In this study, two iron-based alloys were investigated: Fe-10%Ni (at%) and Fe-10%Si (at%), which are known for their promising soft-magnetic properties. A parameter study was first conducted to optimize the process settings with the goal of maximizing the relative density, which strongly influences magnetic performance. Using AI-based optimization software (xT-Saam by Exponential Technologies Ltd., Riga, Latvia), geometrically simple specimens with a relative density of ≥99.95% were successfully produced. Utilizing the developed parameter sets, toroids were manufactured and heat-treated to improve their magnetic properties. The best obtained ferromagnetic properties were H_C = 1621 A/m (coercivity) and µ_R = 305 (permeability) for Fe-10%Ni, and H_C = 300 A/m and µ_R = 1114 for Fe-10%Si. Full article

Two ways of anodizing 3D-printed AlSi10Mg alloy were characterized, and then their fatigue properties were evaluated. Test specimens were fabricated via a laser-powder bed fusion (L-PBF) process followed by machining. Normal and hard anodizing were both conducted in a sulfuric acid bath. The anodized layer was observed using FE-SEM/EDS. Fine Si particles dispersed in the matrix showing web-like patterns were incorporated in the anodized layer. By etching the Si particles away with Keller’s reagent, a characteristic maze-like 3D structure of anodized Al was observed. Then, rotating bending fatigue tests were carried out to evaluate the fatigue strength at 10⁷ cycles. The fatigue strength of the as-machined, normal-anodized and hard-anodized specimens was 106, 100 and 95 MPa, respectively. The fatigue limits were proportional to the surface roughness with higher linearity. By reducing the surface roughness, the fatigue strength of the hard-anodized specimen was improved. This result demonstrates the possibility of improving the fatigue properties of anodized components by reducing their surface roughness. Lastly, a CASS (copper-accelerated acetic acid salt spray) test was conducted, and superior corrosion resistance of the normal- and hard-anodized layers was verified. Full article

A cost-effective Fe-Cr-Mo-B-Si-C metamorphic alloy (HXA5) was newly designed and fabricated as coating material using the high-velocity oxygen fuel (HVOF) thermal spray process, and its microstructure and dry wear resistance were investigated in comparison with a conventional HVOF WC-12Co coating. The HXA5 coating material consisted of a splat area and un-melted powder area. The splat area contained metallic glass, (Cr,Fe)₂B, Cr₂B, and minor Fe-based BCC phases, and the un-melted powder area was composed of Fe-based BCC, (Cr,Fe)₂B, and Cr₂B phases. Room-temperature wear tests revealed that HVOF HXA5 coating material exhibited wear resistance comparable to HVOF WC-12Co coating over ~8.4 km sliding and even superior performance at high-stress wear conditions. This superior wear behavior of HXA5 coating material was attributed to the minimal hardness difference between the metallic glass and boride, the plasticity of the metallic glass, and the formation of a lubricating tribofilm. The wear mechanisms and the influence of alloying elements on glass-forming ability were also discussed. Full article

This study investigates the feasibility of producing low-carbon FeCr via metallothermic smelting of Cr concentrate and chromite spinel powder using a complex FeAlSiCa alloy as the reductant in an induction furnace. The proposed approach offers an alternative to conventional carbothermic and oxygen-blown technologies, reducing both the carbon footprint and airborne emissions. Three charge compositions were tested with varying FeAlSiCa additions (12, 14, and 16 kg per 100 kg of Cr source) and partial replacement of Cr concentrate with up to 20% CSP. Thermodynamic and microstructural analyses were conducted, and the effects of the slag basicity, temperature profiles, and holding time were assessed. In optimal conditions, Cr recovery reached up to 80% with minimal Cr₂O₃ losses in slag, and the resulting alloys met ISO 5448-81 requirements for nitrogen-containing low-carbon FeCr. Microstructural examination revealed the formation of Fe-Cr solid solutions and CrN phases, with V incorporation from the FeAlSiCa alloy. The process proved stable and energy-efficient, producing compact, non-disintegrating slag. This study highlights the potential of induction furnace smelting and chromite spinel powder valorization as a sustainable path for FeCr production. Full article

The present study aims to investigate the microstructural evolution and local mechanical properties of an AlFe18Si8Cr5Ni2 alloy processed via Powder Bed Fusion–Laser-Based Manufacturing (PBF-LB/M). Designed with a focus on sustainability, this alloy was produced by deriving the necessary elements from AlSi10Mg and 304L steel, two of the most widely used alloys and, consequently, among the easiest materials to source from machining scrap. By leveraging iron, chromium, and nickel from these widespread standard compositions, the alloy mitigates the detrimental effects of Fe contamination in Al-based alloys while simultaneously enhancing mechanical performance. A comprehensive investigation of the impact of rapid solidification and thermal cycling offered novel insights into phase stability, elemental distribution, and local mechanical behavior. In particular, microstructural analyses using scanning electron microscopy (SEM), field emission SEM, energy-dispersive X-ray spectroscopy, X-ray diffraction, and differential scanning calorimetry revealed significant phase modifications post PBF-LB/M processing, including Fe-rich acicular phase segregation at melt pool boundaries and enhanced strengthening phase formation. In addition, nanoindentation mapping was used to demonstrate the correlation between microstructural heterogeneity and local mechanical properties. The findings contribute to a deeper understanding of Al-Fe-Si-Cr-Ni alloy changes after the interaction with the laser, supporting the development of high-performance, sustainable Al-based materials for PBF-LB/M applications. Full article

This study explored the effects of T5 and T6 heat treatments on the microstructure and tensile properties of a laser powder bed fusion (LPBF)-fabricated Al–Mn–Mg–Sc–Zr alloy. The as-built condition exhibited a bi-modal grain structure of equiaxed and columnar grains. Specimens after T5 heat treatment also had a bi-modal microstructure with slight grain growth and the precipitation of secondary Al₃Sc, which enhanced the yield strength via precipitation hardening but reduced ductility. In contrast, T6 treatment triggered recrystallization, and the microstructure was only coarse equiaxed α-Al grains. This microstructure change was accompanied by coarsened primary Al₃X and Al₆(Mn, Fe) precipitates, partial Mg₂Si dissolution, and significant secondary Al₃Sc particle growth. Consequently, T6-treated specimens showed lower strength than their T5 counterparts and the poorest ductility due to brittle fracture induced by the stress concentration effect of coarse precipitates at grain boundaries. Full article

This study presents the synthesis of sintered composite foams based on the Invar alloy (64Fe-36Ni), using hollow spherical particles from a nickel superalloy (NiCrSiB) in order to generate porosity. The Invar powder was obtained by mechanical alloying (MA), and the NiCrSiB hollow spherical particles were incorporated into the composite at 20 vol %. The sintering was realized using the spark plasma sintering (SPS) process in an argon atmosphere at 600 °C and 5 MPa, with 10 s holding time. The porous structures were structurally characterized by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The coefficient of linear thermal expansion (CTE) of the Invar/NiCrSiB syntactic foams was found to be 2.52 × 10⁻⁶ °C⁻¹ in the 25–150 °C temperature range and 19.68 × 10⁻⁶ °C⁻¹ in the 150–400 °C range. Full article

The centrifugal atomization process is a rapid solidification method that achieves high cooling rates. Although this technique is typically used to produce common metal powders, it has not been extensively explored for amorphous powder production, despite its clear advantage of generating nearly perfect spherical particles, which is beneficial for subsequent powder consolidation. In this paper, a characterization of three iron-based alloys from the Fe-Si-B system, specifically Fe_91.72Si_5.32B_2.96 (wt%), Fe_87.37Si_6.94B_2.49Cr_2.46C_0.75 (wt%), and Fe_89.41Si_2.02B_1.13P_5.89C_1.55 (wt%), produced by centrifugal atomization, is presented. The amorphous fractions of the powders were quantified using DSC, with further characterization performed via optical microscopy, SEM, and XRD. The amorphous fractions increased with the addition of Cr, C, and P, reaching up to 90% in the Fe_89.41Si_2.02B_1.13P_5.89C_1.55 alloy for particles of <100 μm. The onset cooling rates were estimated to be approximately 10⁶ K/s for Fe_91.7Si_5.32B₃, 10⁵ K/s for Fe_87.36Si_6.9B_2.48Cr_2.45C_0.75, and 10⁴ K/s for Fe_89.41Si_2.02B_1.13P_5.89C_1.55, respectively. Full article

A shape memory alloy with the chemical composition Fe-14Mn-6Si-9Cr-5Ni (mass %) was produced by powder metallurgy (PM) from as-blended powders mixed with mechanically alloyed (MA’ed) powder volumes in amounts of 0, 10 and 20. After powder blending, pressing and sintering, the specimens were hot-rolled, spark erosion cut with different configurations and solution-treated between 700 and 1100 °C. After metallographic preparation, structural analyses were performed by X-ray diffraction and microscopic observation performed by optical and scanning electron microscopy (SEM). The analyses revealed the presence of thermal- and stress-induced martensites caused by solution treatment and pre-straining. Due to the relatively low Mn amount, significant quantities of α′ body center cubic martensite were formed during post-solution treatment water cooling. Solution-treated lamellar specimens underwent a training thermomechanical treatment comprising repeated cycles of room temperature bending, heating and sputtered water cooling. By cinematographic analysis, the occurrence of the shape memory effect (SME) was revealed, in spite of the large amount of α′ bcc martensite. Tensile specimens were subjected to room temperature failure tests and pre-straining (up to 4% permanent strain, after loading–unloading). After tensile pre-straining, a diminution of α′ martensite amount was noticed on XRD patterns, which was associated with the formation of internal sub-bands in the substructure of martensite and were observed by high-resolution SEM. These results prove that SME can be obtained in trained PM_MA’ed Fe-14Mn-6Si-9Cr-5Ni specimens in spite of the large amount of thermally induced α′ bcc martensite, the stress-induced formation of which is impeded by the presence of internal sub-bands. Full article

Manganese-based alloys with the composition Mn₂FeZ (Z = Si, Al) have been extensively investigated in recent years due to their potential applications in spintronics. The Mn₂FeSi alloy, prepared in the form of ingots, powders, or ribbons, exhibits either a cubic full-Heusler (L2₁) structure, an inverse-Heusler (XA) structure, or a combination of both. In contrast, the Mn₂FeAl alloy has so far been synthesized only in the form of ingots, featuring a primitive cubic (β-Mn type) structure. This study focuses on the new quaternary Mn₂FeSi_0.5Al_0.5 alloy synthesized from pure Mn, Fe, Si, and Al powders via mechanical alloying. The elemental powders were ball-milled for 168 h with a ball-to-powder ratio of 10:1, followed by annealing at 550 °C, 700 °C, and 950 °C for 8 h in an argon protective atmosphere. The results demonstrate that annealing at lower temperatures (550 °C) led to the formation of a Heusler structure with a lattice constant of 0.5739 nm. Annealing at 700 °C resulted in the coexistence of several phases, including the Heusler phase and a newly developed primitive cubic β-Mn structure. Further increasing the annealing temperature to 950 °C completely suppressed the Heusler phase, with the β-Mn structure, having a lattice constant of 0.6281 nm, becoming the dominant phase. These findings confirm the possibility of tuning the structure of Mn₂FeSi_0.5Al_0.5 alloy powder—and thereby its physical properties—by varying the annealing temperature. The sensitivity of magnetic properties to structural changes is demonstrated through magnetization curves and zero-field-cooled/field-cooled curves in the temperature range of 5 K to 300 K. Full article