Search Results (562)

In this study, the blends of bio-based polybenzoxazine (V-fa type) and poly(ethylene glycol) (PEG) with PEG contents from 50 to 95 wt% and different molecular weights were developed to improve the flexibility of thermosetting polymers. Of these blends, PEG 8k at 80 wt%, which exhibited the best processability, was selected for further development via compositing with carbon black (CB) from 0 to 20 phr. Differential Scanning Calorimetry (DSC) analysis revealed that the melting temperature (T_m) increased from 70 to 83 °C and glass transition temperatures (T_g) increased from –53 to –48 °C at 20 phr. Thermogravimetric Analysis (TGA) demonstrated high thermal stability, with T_dmax (for all CB contents) presented at ca. 416 °C. Moreover, char yield was increased from 10% (without CB) to 28% (20 phr), reflecting improved decomposition resistance. Mechanical properties demonstrated that CB significantly reinforced the composites. The flexural modulus and flexural strength were increased from 117.18 MPa (without CB) to 456 MPa (10 phr) and from 2.42 MPa (without CB) to 3.94 MPa (2.5 phr), respectively. The SEM images confirmed uniform morphology and good filler dispersion. Conclusively, the composites of 8k PEG 80 wt% filled with 2.5 phr of CB provided an optimal balance of mechanical and thermal stability and engineering polymer applications. Full article

Polymeric membranes are a highly viable technology for wastewater treatment, water purification, and other filtration operations. Accordingly, flat membranes were developed from extruded nanocomposites of polyamide 6 (PA6) and carbon nanotubes (MWCNT), varying the filler content to 1, 3, and 5 parts per hundred resin (phr). The membranes were produced using the phase inversion process through the immersion–precipitation technique. In total, eight membrane compositions were developed with solvent/polymer ratios of 80/20 (weight %). Calcium chloride (CaCl₂) was used as a pore-forming agent at a content of 10 phr. Thus, the characterizations performed were: solution viscosity, FTIR, contact angle measurement, SEM, AFM, water permeability test, and water vapor permeation test. The results showed that the high viscosity of membranes, excessive gelation time, and higher MWCNT contents contributed to a decrease and/or absence of flow. Through SEM images and water flow measurements, the significant influence of CaCl₂ was observed in modifying the membrane morphology (more interconnected porous structures), ensuring the presence of flow. The AFM images also confirm this phenomenon through the increase in roughness. Water vapor transmission increased with higher MWCNT content. These results demonstrate that PA6 and MWCNT membranes were effective for water filtration, only in those where CaCl₂ was used, and for water vapor initially. Full article

The potential of elastomeric composites reinforced with natural fillers to replace traditional synthetic materials in applications involving exposure to acidic environments offers both economic and environmental advantages. On the one hand, these materials contribute to cost reduction and the valorization of organic waste through the development of value-added products. On the other hand, the presence of wood waste in the composite structure enhances biodegradation potential, making these materials less polluting and more consistent with the principles of the circular economy. The present study aims to evaluate the behavior of composites based on Ethylene Propylene Diene Monomer (EPDM) synthetic rubber, reinforced with silica and wood sawdust, in a weakly acidic yet strongly corrosive environment—specifically, acetic acid solutions with concentrations ranging from 10% to 30%. The study also investigates the extent to which varying the proportions of the two fillers affects the resistance of these materials under such environmental conditions. Physico-chemical, structural, and morphological analyses revealed that the materials underwent chemical modifications, such as acetylation of hydroxyl groups. This process reduced the hydrophilic character of the sawdust and, combined with the formation of stable interfaces between the elastomeric matrix and the fillers during vulcanization, limited acid penetration into the composite structure. The composites in which 20 phr or 30 phr of wood sawdust were used-replacing equivalent amounts of silica from the initial 50 phr formulation-demonstrated the highest resistance to the corrosive environments. After 14 days of exposure to a 20% acetic acid solution, the composite containing 30% wood sawdust exhibited a decrease in cross-link density of only 1.44%, accompanied by a reduction in Young’s modulus of just 0.95%. At the same time, tensile strength and specific elongation increased by 22.57% and 26.02%, respectively. FTIR and SEM analysis confirmed good rubber-filler interactions and the stability of the composite structure under acidic conditions. Full article

Background: The platelet-to-hemoglobin ratio (PHR) has emerged as a potential prognostic marker in various cardiovascular contexts, but its role in acute coronary syndrome (ACS), particularly among patients with diabetes mellitus (DM), remains unclear. Methods: In this retrospective cohort study, 843 ACS patients admitted to the 2nd Cardiology Department at Hippokration Hospital of Thessaloniki, Greece, between 2017 and 2023 were evaluated. PHR was calculated from admission complete blood counts. The primary endpoint was all-cause mortality during a median follow-up of 25 months. Multivariate logistic and Cox regression analyses, receiver operating characteristic (ROC) curves, Kaplan–Meier survival analyses, and restricted cubic spline (RCS) models were employed, with subgroup analyses by DM status. Results: Higher PHR was independently associated with increased mortality in the overall cohort (adjusted hazard ratio [aHR] 1.35, p < 0.001). This association showed stronger predictive value in DM patients, reflected in both a higher aHR (1.52 vs. 1.36 in non-DM patients, p < 0.001 and p = 0.018, respectively) and superior discriminative performance on ROC analysis (AUC 0.707 vs. 0.600 overall, p = 0.0006). Kaplan–Meier analysis confirmed poorer survival in high-PHR groups, especially in DM patients. RCS analysis revealed a J-shaped relationship, with risk increasing markedly beyond PHR values of 2.2. Conclusions: PHR is an independent predictor of long-term mortality in ACS, with greater prognostic significance in DM patients. Its simplicity, low cost, and availability from routine blood tests make it a promising tool for risk stratification in ACS. Full article

This study aims to identify and evaluate the phosphate-solubilizing ability of endophytic bacteria isolated from roots of Chinese Cymbidium and to assess their impact on phosphorus uptake and plant growth. Thirty strains of endophytic bacteria were isolated from six orchid varieties. Molecular identification based on 16S rRNA gene sequencing revealed that the most frequently isolated strains belonged to the genera Pseudomonas and Burkholderia. Among them, 10 bacterial strains exhibited the capacity to solubilize inorganic and organic phosphorus. Two strains, designated X1 (Paraburkholderia sp. Beta-32) and X13 (Rhizobium freirei PRF81 (X13), were identified as the most effective phosphate-solubilizing bacteria (PSB). Gluconic acid was the dominant organic acid secreted, driving inorganic phosphorus solubilization, while alkaline phosphatase activities facilitated organic phosphorus mineralization. Inoculation with phosphate-solubilizing bacteria (PSB) resulted in increased plant growth and phosphorus content in both leaves and roots as compared to the control plants. PSB treatments also increased available phosphorus content in soil, reduced total phosphorus content, and increased exopolysaccharide and alkaline phosphatase activities. Real-time q-PCR analysis showed that PSB inoculation significantly upregulated the expression of phosphorus transport-related genes, including PDR2, PHF1, PHR1, PHT1;9, and PHT4;4, thereby enhancing phosphorus absorption. Moreover, strains X1 and X13 not only exhibited strong phosphate-solubilizing capacity but also demonstrated stable colonization in both roots and root rhizosphere soil of orchids over extended periods. In conclusion, the endophytic PSB identified with phosphate-solubilizing abilities increased phosphorus availability and its uptake in Chinese Cymbidium, thereby promoting plant growth and development. This is the first attempt to characterize endophytic PSB from roots of Chinese Cymbidium orchids. These findings provide a basis for selection of PSB that are efficient in P uptake for application in microbial fertilizers for orchid cultivation. Full article

This study aimed to evaluate the physical properties and biodegradability of sulfur-vulcanized polyhydroxyalkanoates (PHAs) with unsaturated side chains. As a vulcanizable PHA, poly(3-hydroxybutyrate-co-3-hydroxy-5-hexenoate) [P(3HB-co-3H5HE)] was biosynthesized with a 3H5HE fraction of 3–47 mol% using recombinant Escherichia coli and subsequently vulcanized with varying sulfur contents (2–20 per hundred resin, phr) in the presence of zinc oxide, stearic acid, and 2-mercaptobenzothiazole as curing agents. The vulcanized PHA copolymers were insoluble in chloroform, indicating the formation of a cross-linked network. Raman spectroscopy revealed the functional loss of the double bonds in the polymers. After the vulcanization with 5 phr sulfur, the tensile strength and elongation at break of P(3HB-co-47 mol% 3H5HE) increased from 0.6 MPa to 6.3 MPa and from 430% to 813%, respectively. This sample exhibited low tensile set (8%) after 200% elongation, indicating rubber-like properties. Although biodegradability decreased with increasing crosslink density, vulcanized P(3HB-co-3H5HE) exhibited a greater degradation potential than vulcanized rubber but was lower than that of non-vulcanized P(3HB-co-3H5HE). These findings demonstrate that sulfur vulcanization can enhance the resilience of unsaturated PHAs, making them suitable for elastomeric and environmental applications. Full article

This study investigated PLA/PCL blends modified with maleic anhydride (MA) via radical grafting using benzoyl peroxide (BPO) as an initiator. Different formulations with 5 and 10 wt.% of PLA-g-MA (containing 1, 3, and 5 wt.% MA) were prepared to evaluate their compatibilizing effect. Samples were characterized thermally, mechanically, and morphologically using DSC, TGA, FTIR, goniometry, SEM, and tensile, impact, and hardness tests. The results show that adding PCL significantly improves the ductility of PLA, though it reduces tensile strength and hardness. Grafting with MA partially improves phase compatibility, as seen by increased elongation at break and impact resistance, especially at intermediate MA concentrations (1–3%). However, higher MA contents lead to greater variability in thermal and mechanical results, likely due to heterogeneous phase dispersion. FTIR analysis detected residual BPO in some formulations, though below 0.1 phr. TGA indicated a slight improvement in thermal stability at 5 wt.% MA. Overall, the findings suggest that controlled use of MA as a compatibilizer enhances the balance of mechanical and thermal properties in PLA/PCL systems. Full article

Polymer-based hybrid composites have emerged as promising platforms for multifunctional energy applications, combining structural versatility with tunable dielectric behavior. In this study, synthesized [Fe(bpy)₃]SO₄; (tris(2,2′-bipyridine)iron(II) sulfate) coordination compound was incorporated into a green epoxy resin matrix to fabricate nanocomposites aimed at enhancing dielectric permittivity (ε′), piezoelectric coefficient (d₃₃, pC/N), energy-storage efficiency (n_rel, %), and mechanical strength (σ, MPa). The integration of the Fe(II) complex via Scanning Electron Microscopy (SEM) confirmed a homogeneous dispersion within the matrix. Broadband Dielectric Spectroscopy (BDS) revealed the presence of three relaxation processes in the spectra of the tested systems, demonstrating enhanced dielectric permittivity with increasing Fe(II) content. Under progressively shorter relaxation times (τ, s), key processes such as interfacial polarization, the polymer matrix’s transition from a glassy to a rubbery state, and the dynamic reorganization of polar side groups along the polymer backbone are activated. The ability to store and retrieve electric energy was confirmed by varying filler content under direct current (dc) conditions. The nanocomposite with 10 phr (mass parts/100 mass parts of resin) filler achieved a piezoelectric coefficient of d₃₃ = 5.1 pC/N, an energy-storage efficiency of n_rel = 44%, and a tensile strength of σ = 55.5 MPa, all of which surpass values reported for conventional epoxy-based composites. These results confirm the ability of the system to store and retrieve electric energy under direct current (dc) fields, while maintaining mechanical robustness and thermal stability due to synergistic interactions between the epoxy matrix and the Fe(II) complex. The multifunctional behavior of the composites underscores their potential as advanced materials for integrated dielectric, piezoelectric, and energy storage and harvesting applications. Full article

Compatibilizers that enhance sustainability and improve the miscibility of polymer blend components have garnered significant attention. This study investigates the difference between the synthetic chain extender Joncryl^® ADR 4468 and the natural epoxidized linseed oil (ELO) Merginat 8510100 as compatibilizers for thermoplastic starch/poly (butylene succinate) (TPS/PBS) blends. Blends containing 40% TPS and 60% PBS were prepared with 1, 3, and 5 phr of each compatibilizer, along with a reference with no additives. The properties of these blends were evaluated using tensile testing, differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), rheology, and scanning electron microscopy (SEM). The findings indicate that while Joncryl^® ADR 4468 significantly improved tensile strength, it also resulted in a brittle fracture. In contrast, ELO batches exhibited greater ductility, albeit with lower tensile strength. These differences are attributed to the chain extension and minor cross-linking effects of Joncryl^® ADR 4468, compared to the increased chain mobility arising from ELO’s plasticizing and compatibilizing actions. Supporting evidence for these observations includes increased cold crystallization temperature (T_cc) and melting temperature (T_m), greater storage modulus along with higher complex viscosity, strengthened interfacial adhesion, and fewer morphological defects in Joncryl^® ADR 4468 blends. These results highlight the importance of selecting an appropriate compatibilizer based on specific application requirements. Overall, this study addresses the knowledge gap regarding the loadings of Joncryl^® ADR 4468 and ELO in TPS/PBS blends and provides a basis for further optimization strategies, such as the incorporation of binary compatibilizers, alternative grafting-based compatibilizers, and twin-screw blending modifications. Full article

This study investigated the development of biocomposites for use as packaging and film in everyday applications. The utilization of rice flour (RF) as a cheap natural filler in the production of polybutylene succinate (PBS) biocomposites has been shown to reduce environmental issues caused by non-biodegradable plastic waste. The effect of rice flour content on the morphology and properties of PBS and RF biocomposites was comprehensively evaluated. Different amounts of rice flour were considered (0, 10, 20, 30, 40, and 50 phr), and a silane coupling agent and epoxidized natural rubber (ENR-50: 1 phr) were used as interfacial agents to improve compatibility between the matrix (PBS) and filler (RF). The PBS/RF biocomposites were prepared using a two-roll mill and shaped into test specimens and films using a compression molding machine. Batches of the composites containing different amounts of RF were prepared in accordance with the standards, and their morphology and properties, including mechanical properties, density, water absorption, and soil burial degradation, were evaluated. The results revealed that the incorporation of silane-treated RF filler and ENR-50 compatibilizer led to notable improvements in mechanical properties, particularly in tensile modulus, flexural strength, flexural modulus, and hardness. A significant improvement in mechanical performance was observed as the RF content increased, with the highest value recorded at the 50 phr loading. The enhancements observed in the composite properties are due to the inherent rigidity of the RF filler and its improved compatibility with the PBS matrix, which together contribute to a stronger and more efficient material. Additionally, the percentage of water absorption in the PBS/RF biocomposites increased with higher RF content. The results from the soil burial test demonstrated that increasing the RF content positively influenced the biodegradability of the PBS/RF biocomposite materials. Full article

Nowadays, the use of materials from renewable resources, such as agricultural waste and forest residues, has increased. In this work, industrial waste recovered from a recycled paper/cardboard company was mechanically refined to obtain ligno-cellulosic microfibers (LCMFs). The obtained LCMFs were well characterized and chemically modified in situ together with natural rubber through silanization. The effect of in situ silanizated LCMFs, by using (3-triethoxysilylpropyl) tetrasulfide (Si69) as a silane coupling agent, on natural rubber (NR) compound properties was studied. The NR compound with silanizated LCMFs at 2.5 phr of Si69 (NR MF Si2) increased NR stiffness significantly. For example, the 300% modulus of NR MF Si2 was around 9 units higher than that of NR. The physical–mechanical properties, crosslink density, curing behavior, infrared spectroscopy, and microscopy of the compounds were studied to confirm the in situ silanization of the microfibers and its reinforcement effect on the NR matrix. The storage modulus (E′) obtained from Dynamic Mechanical Analysis suggested that the silanizated samples presented an uneven crosslinking, but it was enough to stiffen the NR chains. Full article

The objective of this study was to investigate the influence of the lignocellulose filler originating in wood and non-wood raw materials, alone or together with collagen hydrolysate, on the properties and biodegradation ability of natural rubber latex. The different hydrophobicity of the polymer matrix and natural filler makes it difficult to obtain a homogenous structure of the composite. However, the easy biodegradation of the natural filler is a sufficient reason to seek a compromise between its useful properties and the environmental safety of the material. The composites were filled with lignocellulose filler: pine, spruce, and birch wood flour or willow, raspberry, and mallow non-wood flour. Collagen hydrolysate was used as a substitute for lignocellulosic filler, together or alone. The mechanical properties of the composites, their hardness, and equilibrium swelling were studied. In order to determine the morphology and interactions between filler and latex, scanning electron microscopy together with infrared spectroscopy were engaged. The results revealed that after the incorporation of 4 phr of the filler, the increase in mechanical strength was observed even despite the lack of compatibility between the filler and polymer matrix. The lignocellulose filler is a promising agent because its biodegradability contributes to the overall environmental safety of the polymer material. Full article

The growing use of mobile health (mHealth) technologies adds complexity and risk to the healthcare environment. This paper presents a multi-layered cybersecurity assessment of an in-house mHealth platform (PHGL-COVID), comprising a Docker-based server infrastructure, a Samsung Galaxy A55 smartphone, and a Galaxy Watch 7 wearable. The objective was to identify vulnerabilities across the server, mobile, and wearable components by emulating real-world attacks and conducting systematic penetration tests on each layer. Tools and methods specifically tailored to each technology were applied, revealing exploitable configurations, insecure Bluetooth Low Energy (BLE) communications, and exposure of Personal Health Records (PHRs). Key findings included incomplete container isolation, BLE metadata leakage, and persistent abuse of Android privacy permissions. This work delivers both a set of actionable recommendations for developers and system architects to strengthen the security of mHealth platforms, and a reproducible audit methodology that has been validated in a real-world deployment, effectively bridging the gap between theoretical threat models and practical cybersecurity practices in healthcare systems. Full article

As medical technology develops and digital demands grow, personal health records (PHRs) are becoming more patient-centered than before based on cloud-based health information exchanges. While enhancing data accessibility and sharing, these systems present privacy and security issues, including data breaches and unauthorized access. We developed a post-quantum, group-oriented encryption scheme using the Crystal-Kyber Key encapsulation mechanism (KEM). Leveraging lattice-based post-quantum cryptography, this scheme ensures quantum resilience and chosen ciphertext attack security for layered cloud PHR environments. It supports four encryption modes: individual, group, subgroup-specific, and authorized subgroup decryption, meeting diverse data access needs. With efficient key management requiring only one private key per user, the developed scheme strengthens the privacy and security of PHRs in a future-proof, flexible, and scalable manner. Full article

The incorporation of residues into rubber composites has gained attention as a sustainable strategy to address waste management challenges while replacing commercial fillers. In this study, we investigated the potential use of water filter cartridge residue after exhaustion, composed of activated carbon, as a reinforcing filler in vulcanized natural rubber composites. Samples were prepared with 5, 10, 15, and 20 phr (per hundred rubber) of residue and compared to unfilled natural rubber. Stress vs. strain tests reached 13.9 MPa of tension at rupture for composites containing 10 phr of carbon-activated residues, representing a 21.9% increase compared to natural rubber. Interestingly, the tension at rupture for NR/AC_10phr reached values close to those of NR/CB_5phr (with carbon black N330) attaining 14.4 MPa. These results indicate that, even at relatively low concentrations, the carbon filter can offer partial substitution for commercial fillers. Moreover, the use of activated carbon from filter cartridges as filler in rubber composites provides an environmentally favorable alternative to energy-intensive regeneration processes for activated carbon. Full article