Search Results (84)

The approximate pole/zero expressions are computed starting from the state or the “state-like” matrix. The attempts of open-circuit and short-circuit replacement of circuit elements are combined with those to cut row and column groups of the state matrix for poles or the “state-like” matrix for zeros, and with LR iterations. The expressions of all poles and zeros of a wide-band amplifier and an RLC band-stop filter are computed, obtaining significantly better results than those given by the best approach available, implemented in the Analog Insydes package. Full article

The paper presents experimental results for a modified pulsed plasma thruster (PPT) with solid propellant, using a coaxial anode–cathode design. Graphite from pencil leads served as propellant, and a tungsten trigger electrode was tested to reduce carbonization effects. Experiments were performed in a vacuum chamber at 0.001 Pa, employing diagnostics such as discharge current/voltage recording, power measurement, ballistic pendulum, time-of-flight (TOF) method, and a Faraday cup. Current and voltage waveforms matched an oscillatory RLC circuit with variable plasma channel resistance. Key discharge parameters were measured, including current pulse duration/amplitude and plasma channel formation/decay dynamics. Impulse bit values, obtained with a ballistic pendulum, reached up to 8.5 μN·s. Increasing trigger capacitor capacitance reduced thrust due to unstable “pre-plasma” formation and partial pre-discharge energy loss. Using TOF and Faraday cup diagnostics, plasma front velocity, ion current amplitude, current density, and ion concentration were determined. Tungsten electrodes produced lower charged particle concentrations than graphite but offered better adhesion resistance, minimal carbonization, and stable long-term performance. The findings support optimizing trigger electrode materials and PPT operating modes to extend lifetime and stabilize thrust output. Full article

For the measurement of electrical conductivity of metal materials, the traditional contact measurement method has a limited test range and requires periodic electronic calibration. In order to overcome the above shortcomings, this paper takes the inductive response of an RLC circuit driven by alternating sources as the research object and proposes a non-contact method for conductivity measurement of non-ferromagnetic metals engaged by a single-layer solenoid sensor. The effect of the circuit parameters on the inductive sensor characteristics has been described with different resonant modes, and the electric conductivities of different metals can be theoretically calculated based on eddy current. Moreover, the Comsol Multiphysics software is used to conduct finite element analysis to compare the experimental results and the simulation, which is consistent with the theoretical analysis. The measured accuracy of the inductive sensor is verified to be higher than 91% in parallel resonance, which exhibits higher stability and precision than that of series mode. The implementation of this project will provide the theoretical basis and data reference for the detection of electromagnetic properties of unknown metals and has a wide range of applications in non-destructive testing, engineering construction detection, and other fields. Full article

Electromagnetic implosions of hollow lithium cylinders can be utilized to compress magnetized plasma targets in the context of Magnetized Target Fusion (MTF). Two small-scale experiments were conducted at General Fusion as a stepping stone toward compressing magnetized plasmas on a larger scale. The first experiment is an electromagnetic implosion of a lithium ring, and the second is a compression of toroidal magnetic flux by imploding a hollow lithium cylinder onto an hourglass-shaped central structure. Here we present the methodology and results of modelling these experiments with OpenFOAM. Our in-house axisymmetric compressible MHD multi-phase solver was further extended to incorporate: (i) external RLC circuit model for electromagnetic compression coils and (ii) diffusion of the magnetic field into multiple solid materials. The implementation of the external RLC circuit model for electromagnetic coils was verified by comparison with results obtained with FEMM software and with the analytical solution. The solver was then applied to model both experiments and the main conclusions are as follows: (i) modelling solid lithium as a high-viscosity liquid is an adequate approach for the problems considered; (ii) the magnetic diffusivity of lithium is an important parameter for the accurate prediction of implosion trajectories (for the implosion of the lithium ring, higher values of magnetic diffusivity in the range $0.2 \le {\eta }_{\mathrm{ring}}[{\mathrm{m}}^2/\mathrm{s}] \le 0.5$ resulted in a better fit to the experimental data with a relative deviation in the trajectory of $\lesssim 20\%$); (iii) simulation results agree well with experimental data, and in particular, the toroidal field amplification of 2.25 observed in the experiment is reproduced in simulations within a relative error margin of 20%. The solver is proven to be robust and has the potential to be employed in a variety of applications. Full article

In this paper, a compact wideband filtering monopole is presented for remote terrestrial omnidirectional communication systems. The presented antenna features a sleeve monopole structure integrating with two key components: the lumped parallel RLC circuits and an embedded high–low impedance structure within the sleeve section. The integrated high–low impedance structure enables the monopole to achieve excellent filtering characteristics while maintaining the monopole compactly. Meanwhile, the combination of the RLC loads and the sleeve monopole ensures wideband omnidirectional radiation performance. To validate the design, a prototype operating from 200 to 1500 MHz is fabricated and tested. The measurement results demonstrate that the monopole achieves a VSWR below 3 across the entire operating band and a measured gain exceeding 0 dB. Furthermore, the monopole exhibits satisfactory out-of-band rejection from 1700 to 4000 MHz, confirming its effective filtering capability. Full article

A quantitative analysis of the fault transient is critical for system resilience assessment and protection coordination. Focusing on hybrid modular multilevel converter (MMC)-based HVDC architecture with enhanced fault ride-through (FRT) capability, this study develops a mathematical calculation framework to quantify how controller configurations influence fault current profiles. Unlike conventional static topologies (e.g., RLC or fixed-voltage RL circuits), the proposed model integrates an RL network with a time-variant controlled voltage source, which can emulate closed-loop control response during the FRT transient. Then, the quantitative relationship is established to map the parameters of DC controllers to the fault current across diverse FRT strategies, including scenarios where control saturation dominates the transient response. Simulation studies conducted on a two-terminal MMC-HVDC architecture substantiate the efficacy and precision of the developed methodology. The proposed method enables the evaluation of DC fault behavior for hybrid MMCs, concurrently appraising FRT control strategies. Full article

This review systematically examines recent advances in self-powered wireless sensing technologies based on triboelectric nanogenerators (TENGs), focusing on innovative methods that leverage breakdown discharge effects to achieve high-precision and long-distance signal transmission. These methods offer novel technical pathways and theoretical frameworks for next-generation wireless sensing systems. To address the core limitations of conventional wireless sensors, such as a restricted transmission range, high power consumption, and suboptimal integration, this analysis elucidates the mechanism of the generation of high-frequency electromagnetic waves through localized electric field ionization induced by breakdown discharge. Key research directions are synthesized to enhance TENG-based sensing capabilities, including novel device architectures, the optimization of RLC circuit models, the integration of machine learning algorithms, and power management strategies. While current breakdown discharge sensors face challenges such as energy dissipation, multimodal coupling complexity, and signal interpretation barriers, future breakthroughs in material engineering and structural design are anticipated to drive advancements in efficiency, miniaturization, and intelligent functionality in this field. Full article

The residual magnetism of the iron core of power transformers can cause an excitation inrush current, posing a threat to the safe and stable operation of the power grid. This paper proposes a transformer remanence measurement method based on a demagnetization hysteresis loop to address the problems of large errors, complex operation, and poor universality in existing remanence measurement methods. This method is designed for off-grid transformers to avoid potential interference to the power grid caused by current pulses during the measurement process. This method constructs an RLC oscillation circuit that utilizes capacitor energy storage and iron core magnetic field energy conversion, combined with the dynamic characteristics of hysteresis loops, to achieve accurate measurement of residual magnetism and synchronous demagnetization. The effectiveness of this method has been verified through residual magnetism measurement experiments on ring transformers and large converter transformers, and it can be applied in specific engineering practice operations. Theoretical analysis shows that the charging range of energy storage capacitors is affected by the hysteresis characteristics of the iron core and the saturation magnetic flux, and the residual magnetization value can be directly calculated based on the difference in the intersection point of the longitudinal axis of the demagnetization hysteresis loop. Simulation and experimental results show that the measurement error of the proposed method is less than 5%—significantly better than traditional methods. This method does not require complex control strategies, has high precision and efficiency, and can provide reliable technical support for residual magnetism detection and suppression of off-grid power transformers. Full article

The current research study presents a comprehensive analysis of the local discontinuous Galerkin (LDG) method for solving multi-order fractional differential equations (FDEs), with an emphasis on circuit modeling applications. We investigated the existence, uniqueness, and numerical stability of LDG-based discretized formulation, leveraging the Liouville–Caputo fractional derivative and upwind numerical fluxes to discretize governing equations while preserving stability. The method was validated through benchmark test cases, including comparisons with analytical solutions and established numerical techniques (e.g., Gegenbauer wavelets and Dickson collocation). The results demonstrate that the LDG method achieves high-accuracy solutions (e.g., with a relatively large time step size) and reduced computational costs, which are attributed to its element-wise formulation. These findings position LDG as a promising tool for complex scientific and engineering applications, particularly in modeling fractional-order systems such as RL, RLC circuits, and other electrical circuit equations. Full article

To solve the problem of long turn-off times for transient electromagnetic (TEM) transmitters with inductive loads, a new second-order fast discharge circuit topology added into the original H-bridge structure for TEM transmitters is presented, which includes a capacitor, two Metal-Oxide-Semiconductor Field-Effect Transistors (MOSFETs), and two resistors. Firstly, the four operating stages and principles of the second-order circuit were analyzed. Then, the mathematical models of the turn-off time of the current and the voltage stress of the Metal-Oxide-Semiconductor Field-Effect Transistor (MOSFET) were established using the analytical method. Finally, the parameters of the resistor and capacitor were selected by finding the optimal solution for the fixed transmitter coil. Compared with the simulation results of the other two topologies, the proposed topology demonstrates a current-independent turn-off time and achieves the shortest duration at 50 A, while maintaining lower voltage stress at 9 A. The experimental results of the prototype show that the turn-off time is always about 64 μs when the currents are 1 A, 5 A, and 9 A. Simulation and experimental results show that the second-order circuit reduces the MOSFET’s turn-off time to 58 μs via Resistor–Inductor–Capacitor (RLC) series resonance, with the turn-off duration remaining load-current-independent. Full article

As a kind of important functional device, terahertz metamaterial absorbers (TMA) have been focused on by many researchers for their capacity to absorb electromagnetic waves and wide application fields. In this work, we designed a terahertz metamaterial absorber with narrow-band absorption for refractive index sensing, which consisted of a circular metal ring resonator and a square metal ring resonator. The simulation results show that the absorptivity of the proposed TMA reached over 68.8% and 93.27% at 1.926 and 4.413 THz, respectively. Moreover, the absorption mechanism was studied through the electromagnetic field energy distribution, and the influence of structural parameters on absorption performance was exhibited. In refractive index sensing, a high sensitivity (S) of 2.537 THz/RIU (refractive index unit, RIU) was achieved by utilizing the coupling of ring resonators. The maximal quality factor (Q-factor) and figure of merit (FOM) of the TMA were 234.73 and 147.67 RIU⁻¹, respectively. Additionally, we established an RLC equivalent circuit model (ECM) for the TMA, and we further illustrated the performance of the TMA in refractive index sensing through fitting the sensitivity based on the ECM to the sensitivity of the TMA. Our study exhibits the considerable potential application for the field of terahertz sensing, and the ECM for refractive index sensing will be helpful for continual investigation. Full article

The model presented by Gabriel Kron in 1945 is an example of an analog computer simulating quantum phenomena on a hardware level. It uses passive RLC elements to construct a hardware solver for the problem of quantum particles confined by rectangular or other classes of potential. The analytical and numerical validation of Kron’s second model is conducted for different shapes of particle-confining potentials in the one-dimensional case using an LTspice simulator. Thus, there remains potential for obtaining solutions in two- and three-dimensional cases. Here, a circuit model representing a linearized Ginzburg–Landau equation is given. Kron’s second model is generalized by the introduction of linear and non-linear resistive elements. This transforms the deformed Schrödinger equation into a linear dissipative Schrödinger equation and its non-linear form. The quantum mechanical roton problem is the main result of this work and is formulated by means of classical physical states naturally present in the LC classical circular electrical transmission line. The experimental verification of Kron’s model is confirmed. Full article

In recent years, with the burgeoning application of high voltage in various industrial sectors, the deployment of unmanned equipment, such as industrial heavy-load Unmanned Aerial Vehicles (UAVs), incorporating high-capacity Insulated-Gate Bipolar Transistors (IGBTs), has become increasingly prevalent. The demand for high-voltage IGBT modules in UAV is continuously growing; therefore, exploring methods to predict fault precursor parameters of multi-chip IGBT modules is crucial for the operational health management of unmanned equipment like UAVs. This paper analyzes the gate charge degradation in multi-chip IGBT modules after thermal cycling, which can be used to evaluate the operational state of these modules. Furthermore, to delve into the electrical response of a gate drive circuit caused by local damage within the IGBT module, an RLC model incorporating parasitic parameters of the gate drive circuit is established, and a sensitivity analysis of the peak current in the gate charge circuit is provided. Additionally, in the experimental circuit, an open sample of an IGBT module with partial bond wires lifted off is used to simulate actual faults. The analysis and experimental results indicate that the peak current of the gate charge is closely related to L and C. The significant deviation in the gate current, influenced by the partial bond wires lift-off, can provide a basis for the development of predictive methods for IGBT modules. Full article

Due to system complexity, research on fuzzy fractional-order, singular perturbation, multi-agent systems (FOSPMASs) remains limited in control theory. This article focuses on the leader-following consensus of fuzzy FOSPMASs with orders in the range of $\left(0, 2\right)$. By employing the T-S fuzzy modeling approach, a fuzzy FOSPMAS is constructed. In order to achieve the consensus of a FOSPMAS with multiple time-scale characteristics, a fuzzy observer-based controller is designed, and the error system corresponding to each agent is derived. Through a series of equivalent transformations, the error system is decomposed into fuzzy singular fractional-order systems (SFOSs). The consensus conditions of the fuzzy FOSPMASs are obtained based on linear matrix inequalities (LMIs) without an equality constraint. The theorems provide a way to tackle the uncertainty and nonlinearity in FOSPMASs with orders in the range of $\left(0, 2\right)$. Finally, the effectiveness of the theorems is verified through an RLC circuit model and a numerical example. Full article

This paper introduces a novel approach to neural networks: a Generalized Liquid Neural Network (GLNN) framework. This design excels at handling both sequential and non-sequential tasks. By leveraging the Runge Kutta DOPRI method, the GLNN enables dynamic simulation of complex systems across diverse fields. Our research demonstrates the framework’s capabilities through three key applications. In predicting damped sinusoidal trajectories, the Generalized LNN outperforms the neural ODE by approximately 46.03% and the conventional LNN by 57.88%. Modelling non-linear RLC circuits shows a 20% improvement in precision. Finally, in medical diagnosis through Optical Coherence Tomography (OCT) image analysis, our approach achieves an F1 score of 0.98, surpassing the classical LNN by 10%. These advancements signify a significant shift, opening new possibilities for neural networks in complex system modelling and healthcare diagnostics. This research advances the field by introducing a versatile and reliable neural network architecture. Full article