Search Results (37)

This paper aims to support stakeholders in the sustainable construction sector by exploring the potential of unexamined aggregates from five distinct origins: the Jandol River, the Swat River, the Panjkorha River, the Kitkot Drain, and the Shavey Drain situated in Malakand division, North Waziristan, Pakistan, concerning Alkali–Silica Reaction (ASR) prior to their incorporation into large-scale construction practices. Petrographic examination for the determination of the mineralogical composition of all collected aggregates revealed that aggregates stemming from the Swat River, Panjkorh River, Kitkot Drain, and Shavey Drain exhibited no reactive minerals. In contrast, those from the Jandol River showed reactive mineral content. Physical analysis of the aggregates revealed that Jandol River aggregates had superior resistance to impact, crushing, and abrasion, having values of 18.53%, 18.53%, and 20.10%, respectively. Moreover, the chemical analysis exhibited the highest silica content (SiO₂) in Jandol River aggregates, i.e., 94.7%, respectively. Samples in the form of cubes, prisms, and mortar bars were prepared to study both the mechanical properties and the expansion tendencies of specimens prepared from different aggregate sources. Validation of the reactive nature of the Jandol River aggregates was corroborated by the expansion results obtained from the mortar bars and the reduction in compressive strength and flexure strength by 8.2% and 9.2%, respectively, after 90 days, higher than that of aggregates exposed to ASR sourced from the other four origins. It can be asserted that aggregates from the Jandol River source are more susceptible to ASR as compared to other aggregates. To mitigate the potential of ASR, various strategies, such as using low reactivity, natural, or processed aggregates; low alkali-containing cement; inducing pozzolanic substances in concrete; etc., are recommended. Simultaneously, an economic feasibility study and environmental assessments are recommended as future developments. Full article

This research presents the impact of diesel blends with tire pyrolysis oil (TPO) as an additive for minimizing the wear and tear of engine components. This study investigates the blends of normative diesel oil with TPO content ranging from 5% m/m to 20% m/m. Reference measurements are made for pure diesel oil (D100) and pure TPO. This investigation included an evaluation of the corrosion effect and the effect of the fuels tested on abrasive wear. For each fuel, the sulfur content, water content, lubricity (which is defined as the corrected average diameter of the wear trace during the high-frequency reciprocating rig (HFRR) test), and impurity content are determined. Impurities are assessed using indicators such as ash residue, coking residue from 10% distillation residue, determination of wear metals and contaminants, insoluble impurity content, and total sediment by hot filtration. All parameters are determined using recognized methods described in international standards. Approximation models are built for all the analyzed parameters, which can be used in future studies. At the same time, the individual values of the analyzed factors are compared with the threshold values specified in selected standards and regulations. Consequently, it is possible to assess the usefulness of individual fuels in terms of meeting the requirements for minimum wear of engine components. The results show the suitability of pyrolysis oil and the potential for its use as an additive to fossil fuels in terms of meeting most factors. Some of the fuels tested did not meet the standards for acceptable sulfur content. However, in terms of sulfur content, all of the analyzed fuels can be used to power watercraft and land-based power and thermal power plants equipped with flue gas desulphurization systems. A second indicator for not meeting the standards is the ash residue value, which indicates the high content of non-combustible, mainly metallic, substances in the pyrolysis oil used for the tests. Post-recycled oils must, therefore, undergo appropriate purification before being used as an additive to diesel fuels for internal combustion engines. Once the post-recycling oil has been subjected to desulfurization and advanced filtration, it can be used as a fuel additive for land vehicles, which fits in with closed-loop economies and sustainable development strategies. Full article

The development of skin-protective materials that prevent the adhesion of cnidarian nematocysts and enhance the mechanical strength of these materials is crucial for addressing the issue of jellyfish stings. This study aimed to construct superhydrophobic nanomaterials capable of creating a surface that inhibits nematocyst adhesion, therefore preventing jellyfish stings. We investigated wettability and nematocyst adhesion on four different surfaces: gelatin, polydimethylsiloxane (PDMS), dodecyl trichlorosilane (DTS)-modified SiO₂, and perfluorooctane triethoxysilane (PFOTS)-modified TiO₂. Our findings revealed that an increase in hydrophobicity significantly inhibited nematocyst adhesion. Furthermore, DTS-modified sprayed SiO₂ and PFOTS-modified sprated TiO₂ were further enhanced with low-surface-energy substances—cellulose nanofibers (CNF) and chitin nanocrystals (ChNCs)—to improve both hydrophobicity and mechanical strength. After incorporating CNF and ChNCs, the surface of s-TiO₂-ChNCs exhibited a contact angle of 153.49° even after undergoing abrasion and impact tests, and it maintained its hydrophobic properties with a contact angle of 115.21°. These results indicate that s-TiO₂-ChNCs can serve as an effective skin coating to resist tentacle friction. In conclusion, this study underscores the importance of utilizing hydrophobic skin materials to inhibit the adhesion of tentacle nematocysts, providing a novel perspective for protection against jellyfish stings. Full article

Aloe vera is well known for its biological properties as a bioflavonoid anti-inflammatory and antibacterial agent. It has been used frequently in the food sector as a food coating due to its hygroscopic properties and as an ingredient in the lucrative cosmetic industry. Studies have also included aloe vera as an eco-friendly green solution based on these properties. The current research focuses on the use of aloe vera gel in printing pastes as an alternative sustainable solution to synthetic thickeners, evaluating its wet performance and ease of fabric stitching, and has been inspired by studies that similarly used this substance and measured its effect on the fabric’s coefficient of friction and antimicrobial action. In the current study, printing pastes with natural colourants, such as saffron, curcumin, and annatto, and aloe vera gel thickener derived from natural leaves from Crete increased the fabric’s mechanical resistance to abrasion compared to the untreated pastes. The measured performance did not differ substantially from prints with traditional synthetic pastes, hence tolerating the substitution with the non-contaminant variant. The enhanced resistance to abrasion and wear extends the fabric’s serviceable life and resulting garments, decreasing the need for high industry processing volumes and, as a result, reducing pollution. The resistance to wear was evaluated using the dominant method in textile testing of the Martindale apparatus, which measured the cycles to failure, weight loss, and general appearance deterioration using the official photographic standards. Full article

In order to further enhance the erosion resistance of cement concrete pavement materials, this study constructed an apparent rough hydrophobic structure layer by spraying a micro-nano substrate coating on the surface layer of the cement concrete pavement. This was followed by a secondary spray of a hydroxy-silicone oil-modified epoxy resin and a low surface energy-modified substance paste, which combine to form a superhydrophobic coating. The hydrophobic mechanism of the coating was then analysed. Firstly, the effects of different types and ratios of micro-nano substrates on the apparent morphology and hydrophobic performance of the rough structure layer were explored through contact angle testing and scanning electron microscopy (SEM). Subsequently, Fourier transform infrared spectroscopy and permeation gel chromatography were employed to ascertain the optimal modification ratio, temperature, and reaction mechanism of hydroxy-silicone oil with E51 type epoxy resin. Additionally, the mechanical properties of the modified epoxy resin-low surface energy-modified substance paste were evaluated through tensile tests. Finally, the erosion resistance of the superhydrophobic coating was tested under a range of conditions, including acidic, alkaline, de-icer, UV ageing, freeze-thaw cycles and wet wheel wear. The results demonstrate that relying solely on the rough structure of the concrete surface makes it challenging to achieve superhydrophobic performance. A rough structure layer constructed with diamond micropowder and hydrophobic nano-silica is less prone to cracking and can form more “air chamber” structures on the surface, with better wear resistance and hydrophobic performance. The ring-opening reaction products that occur during the preparation of modified epoxy resin will severely affect its mechanical strength after curing. Controlling the reaction temperature and reactant ratio can effectively push the modification reaction of epoxy resin through dehydration condensation, which produces more grafted polymer. It is noteworthy that the grafted polymer content is positively correlated with the hydrophobicity of the modified epoxy resin. The superhydrophobic coating exhibited enhanced erosion resistance (based on hydrochloric acid), UV ageing resistance, abrasion resistance, and freeze-thaw damage resistance to de-icers by 19.41%, 18.36%, 43.17% and 87.47%, respectively, in comparison to the conventional silane-based surface treatment. Full article

Quinacridone (QA) and 2,9-dimethylquinacridone (DQA) are synthetic substances suitable as a hard, abrasion-resistant, self-organizing gliding layer on ice and snow. For sustainable use, a large number of parameters must be considered to demonstrate that these non-biogenic substances and their by-products and degradation products are harmless to humans and the environment in the quantities released. For this task, available experimental data are used and supplemented for all tautomers by numerous relevant physical, chemical, toxicological and ecotoxicological estimated values based on various Quantitative Structure Activity Relationship (QSAR) methods. On the one hand, the low solubility of QA and DQA leads to stable gliding layers and thus, low abrasion and uptake by plants, animals and humans. On the other hand, the four hydrogen bond forming functional groups per molecule allow nanoparticle decomposition and enzymatic degradation in natural environments. All available data justify a sustainable use of QA and DQA as a gliding layer. The assessment of the toxicological properties is complemented by an investigation of the size and morphology of DQA particles, as well as field tests indicating excellent performance as a gliding layer on snow. Full article

Ice accumulation on glass insulators is likely to cause faults such as flashover, tripping and power failure, which interfere with the normal operation of the power grid. Accordingly, superhydrophobic coatings with great anti-icing potential have received much attention. In this study, three superhydrophobic coatings (PTFE, Al₂O₃ and SiO₂) were successfully prepared on glass surfaces by using one-step spraying. The microscopic morphology, wettability, anti-icing and anti-glaze icing properties of the superhydrophobic coatings were comparatively analyzed. The results indicated that the PTFE coating had a densely distributed rough structure, showing a contact angle of 165.5° and a sliding angle of 3.1°. The water droplets on the surface could rebound five times. Compared with the Al₂O₃ and SiO₂ coatings, the anti-icing performance of the PTFE coating was significantly improved. The freezing time was far more than 16 times that of glass (4898.7 s), and the ice adhesion strength was 9 times lower than that of glass (27.5 kPa). The glaze icing test in the artificial climate chamber showed that the icing weight of the PTFE coating was 1.38 g, which was about 32% lower than that of the glass. In addition, the icing/melting and abrasion cycles destroyed the low-surface-energy substances and nanostructures on the surface, leading to the degradation of the anti-icing durability of the PTFE coatings. However, the PTFE coating still maintained excellent hydrophobicity and anti-icing properties after UV irradiation for up to 624 h. The superhydrophobic coatings prepared in this work have promising development prospects and offer experimental guidance for the application of anti-icing coatings on glass insulators. Full article

This review aims to summarize the literature data regarding the effects of different toothpaste compounds in the zebrafish model. Danio rerio provides an insight into the mechanisms of the ecotoxicity of chemicals as well as an assessment of their fate in the environment to determine long-term environmental impact. The regular use of adequate toothpaste with safe active ingredients possessing anti-bacterial, anti-inflammatory, anti-oxidant, and regenerative properties is one of the most effective strategies for oral healthcare. In addition to water, a typical toothpaste consists of a variety of components, among which three are of predominant importance, i.e., abrasive substances, fluoride, and detergents. These ingredients provide healthy teeth, but their environmental impact on living organisms are often not well-known. Each of them can influence a higher level of organization: subcellular, cellular, tissue, organ, individual, and population. Therefore, it is very important that the properties of a chemical are detected before it is released into the environment to minimize damage. An important part of a chemical risk assessment is the estimation of the ecotoxicity of a compound. The zebrafish model has unique advantages in environmental ecotoxicity research and has been used to study vertebrate developmental biology. Among others, the advantages of this model include its external, visually accessible development, which allows for providing many experimental manipulations. The zebrafish has a significant genetic similarity with other vertebrates. Nevertheless, translating findings from zebrafish studies to human risk assessment requires careful consideration of these differences. Full article

Tribological testing of moving shaft/sealing pairs in complex environments is at the frontline of research. Machines working in abrasive conditions are subject to different wear effects. It is not only valid on Earth but especially valid for rovers and future robots used in Mars and Moon missions. The aim of our joint research with the European Space Agency is to study the abrasion phenomena of moving machine elements on Mars and the Moon by using artificial soil samples (“simulants”). This review details mainly the available simulant sources and recommend a selection of the most suitable ones for tribological testing. Moreover, the potential mating structural materials subjected to abrasive space applications are reviewed briefly. The tribological tests are exploring the features of the rotary shaft/seal relationship that is subject to dry friction and intense abrasion. By using the simulants, measurements are performed under laboratory conditions with both a sample test and a real shaft/seal connection. Parameters of the selection criteria were defined, and classification of the simulant sources were made. It was found that simulant particle size distribution and chemical substance content are detailed enough only for a limited type of available artificial Moon and Mars soil samples. Four simulants were identified and applied later in the tribological testing. For the shaft materials, based on a detailed case study of polymers, steel, and aluminum alloys, a high-strength aluminum alloy with a hard anodized surface and a stainless steel were selected for further abrasion tests. Full article

In this work, a durable superhydrophobic fabric was fabricated by using a facile UV-induced surface covalent modification strategy. 2-isocyanatoethylmethacrylate (IEM) containing isocyanate groups can react with the pre-treated hydroxylated fabric, producing IEM molecules covalently grafted onto the fabric’s surface, and the double bonds of IEM and dodecafluoroheptyl methacrylate (DFMA) underwent a photo-initiated coupling reaction under UV light radiation, resulting in the DFMA molecules further grafting onto the fabric’s surface. The Fourier transform infrared, X-ray photoelectron spectroscopy and scanning electron microscopy results revealed that both IEM and DFMA were covalently grafted onto the fabric’s surface. The formed rough structure and grafted low-surface-energy substance contributed to the excellent superhydrophobicity (water contact angle of ~162°) of the resultant modified fabric. Notably, such a superhydrophobic fabric can be used for efficient oil–water separation, for example a high separation efficiency of over 98%. More importantly, the modified fabric exhibited excellent durable superhydrophobicity in harsh conditions such as immersion in organic solvents for 72 h, an acidic or alkali solution (pH = 1–12) for 48 h, undergoing laundry washing for 3 h, exposure to extreme temperatures (from −196° to 120°), as well as damage such as 100 cycles of tape-peeling and a 100-cycle abrasion test; the water contact angle only slightly decreased from ~162° to 155°. This was attributed to the IEM and DFMA molecules grated onto the fabric through stable covalent interactions, which could be accomplished using the facile strategy, where the alcoholysis of isocyanate and the grafting of DFMA via click coupling chemistry were integrated into one-step. Therefore, this work provides a facile one-step surface modification strategy for preparing durable superhydrophobic fabric, which is promising for efficient oil–water separation. Full article

This scoping review aims to evaluate methods of conservative reconstruction of dental enamel lesions resulting from abrasions and evaluate the effect of diode laser in reducing the symptoms of tooth sensitivity. The cementoenamel junction is more prone to substance loss because the enamel thickness is substantially decreased, resulting in a much weaker enamel–dentin bond. Methods: Dental abrasion was examined in the mechanical cause alone. Pubmed, Scopus, and Web of Science were used to discover publications that matched our topic from 1 January 2018 to 20 March 2023. A comparison of various non-carious cervical lesion (NCCL) restoration treatments was generated mostly by mechanical considerations. Results: A final number of 11 clinical trials and randomized controlled trials were included in the review for qualitative analysis. Composite resins performed well in clinical trials for the restoration of NCCLs. Conclusions: Composite, in its different forms of filling and consistency, preceded by the use of adhesives, is an efficient and effective material for the treatment of NCCLs. Diode laser use prior to NCCL restoration of teeth does not diminish restoration retention rate, may lessen hypersensitivity, and may affect restoration success. Full article

Serious damage caused by oily wastewater makes the development of efficient superhydrophobic and superoleophilic materials for oil/water separation processes critical and urgent. Herein, durable superhydrophobic nanometer-scale TiO₂ grains with low-surface-energy substance composite-modified materials were fabricated by using a cost-effective and facile synthesis method for the gravity-driven separation of oil/water mixtures under harsh conditions. Different substrates, such as sawdust, wheat straw, cotton, sponge and fabric, were applied for superhydrophobic surface preparation, and various low-surface-energy reagents could interact with deposited TiO₂ nanoparticles, including cetylamine, dodecanethiol, stearic acid and HDTMS. The resultant materials showed superhydrophobic properties with a water contact angle (WCA) higher than 150.8°. The separation of various oil/water mixtures with high efficiency and purity was acquired by using the as-prepared sponge. More importantly, the coated sponge exhibited good resistance to various harsh environmental solutions. Moreover, its superhydrophobicity also remained even after 12 months of storage in air or 10 cycles of abrasion. The durable superhydrophobic coating prepared in this work could be practically used for the highly efficient separation of oil/water mixtures under various harsh conditions. Full article

Molecular traps, based on natural zeolites, are being used to remove harmful gaseous substances (VOCs). These chemical devices must be supported on an adequate substrate (e.g., paper, polymeric films, etc.). To achieve very strong adhesion with the substrate, the planar shape is the most convenient choice for these systems. Clinoptilolite is a nanostructured material made of nanosized lamellae with a thickness of 40 nm. A new technological approach, based on the use of an abrasive drill, was selected to exfoliate a natural clinoptilolite sample, thus leading to a powder made of single lamellar crystals. The obtained lamellae have been characterized by TEM, SEM/EDS, and XPS. Full article

A superhydrophobic (SH) surface is typically constructed by combining a low-surface-energy substance and a high-roughness microstructure. Although these surfaces have attracted considerable attention for their potential applications in oil/water separation, self-cleaning, and anti-icing devices, fabricating an environmentally friendly superhydrophobic surface that is durable, highly transparent, and mechanically robust is still challenging. Herein, we report a facile painting method to fabricate a new micro/nanostructure containing ethylenediaminetetraacetic acid/poly(dimethylsiloxane)/fluorinated SiO₂ (EDTA/PDMS/F-SiO₂) coatings on the surface of a textile with two different sizes of SiO₂ particles, which have high transmittance (>90%) and mechanical robustness. The different-sized SiO₂ particles were employed to construct the rough micro/nanostructure, fluorinated alkyl silanes were employed as low-surface-energy materials, PDMS was used for its heat-durability and wear resistance, and ETDA was used to strengthen the adhesion between the coating and textile. The obtained surfaces showed excellent water repellency, with a water contact angle (WCA) greater than 175° and a sliding angle (SA) of 4°. Furthermore, the coating retained excellent durability and remarkable superhydrophobicity for oil/water separation, abrasion resistance, ultraviolet (UV) light irradiation stability, chemical stability, self-cleaning, and antifouling under various harsh environments. Full article

Construction of superhydrophobic woods with high abrasion resistance is still a major challenge, and micro analysis for abrasion resistance is scarce. To improve these issues, cellulose nanocrystals (CNC)@SiO₂@phosphorylated lignin (PL) rods were prepared by SiO₂ in situ generated on CNC, and then the modified lignin attached to the CNC@SiO₂ rods surface. Subsequently, the superhydrophobic coating was constructed using hydrophobic modified CNC@SiO₂@PL rods as the main structural substance by simple spraying or rolling them onto wood surfaces, and both polydimethylsiloxane (PDMS) and epoxy resin were used as the adhesives. The resulting coating had excellent superhydrophobic properties with a water contact angle (WCA) of 157.4° and a slide angle (SA) of 6°. The introduced PL could enhance ultraviolet (UV) resistance of the coating due to the presence of these groups that absorbed UV light in lignin. In the abrasion resistance test, compared with the SiO₂/PL coating, the abrasion resistance of the one with CNC was much higher, suggesting that CNC could improve the abrasion resistance of the coating due to its high crystallinity and excellent mechanical strength. The coating with PDMS performed better than the one with epoxy resin because the soft surface could offset part of the external impact by deformation in the abrasion process. This was also consistent with the results of the nanoindentation (NI) tests. In view of the simple preparation and good performance, this superhydrophobic wood will have broad application potential. Full article