Search Results (9,741)

The development of edible hydrogels with both high strength and toughness remains a considerable challenge. Herein, we report an innovative and straightforward method to prepare robust kappa-carrageenan/konjac glucomannan (κ-car/KGM) double network hydrogels (DNs) through a single heating-cooling cycle followed by immersion in an Na₂CO₃ solution. This method effectively tuned the crosslinking densities of both the rigid κ-car-k⁺ first network and the ductile KGM second network. The resulting κ-car-k⁺/KGM-1:2 DNs demonstrated outstanding mechanical properties, exhibiting compressive strength approximately 10- and 20-fold greater than that of the corresponding single network (SN) κ-car-k⁺ and KGM hydrogels, respectively, accompanied by remarkable toughness. This enhancement is attributed to a sequential failure mechanism where the rigid κ-car-k⁺ network fractures first to dissipate energy, while the ductile KGM network remains intact to maintain structural integrity. Furthermore, the sensory profile of the κ-car-k⁺/KGM-1:2 DNs was remarkably similar to that of squid across all five evaluated attributes (hardness, elasticity, chewiness, brittleness, and palatability). Similarly, the κ-car-k⁺/KGM-1:1 DNs closely matched the sensory profile of abalone, particularly in elasticity, chewiness, brittleness, and palatability. These findings suggest the prepared edible DNs have great potential to simulate high-chewing seafood, offering a new pathway for designing advanced food materials from natural polysaccharides. Full article

Poly(N-isopropylacrylamide) (PNIPAAm) hydrogels exhibit temperature-responsive volume changes near physiological temperature, but their low mechanical strength in the swollen state limits use in structurally demanding biomedical applications. In this study, we systematically investigated poly(NIPAAm-co-acrylamide), P(NIPAAm-co-AAm), hydrogels with varying AAm-to-NIPAAm ratios to explore the compositional trade-offs between thermal responsiveness and mechanical performance. Hydrogels were synthesized under fixed crosslinker and water content conditions, and evaluated through compressive mechanical testing, thermal swelling analysis, and crosslinking density estimation. Our results show that increasing AAm content enhances mechanical strength and stiffness but reduces the magnitude of temperature-induced volumetric shrinkage. An intermediate comonomer formulation demonstrated an optimal balance, maintaining both sufficient mechanical integrity for transdermal microneedle insertion and a reversible volume transition. This study highlights the potential of compositional tuning in hydrogel systems to meet the competing demands of responsiveness and durability in advanced biomedical applications. Full article

Repairing large bone defects remains a significant clinical challenge due to the limitations of current treatments, including infection risk, donor site morbidity, and insufficient vascularization. The autograft is still the gold standard for large bone defects. In this study, we developed chitosan-based (CS-based) scaffolds, incorporating with hydroxyapatite (HAp) and fluorapatite (FAp) ceramics, fabricated by UV crosslinking and freeze-drying, and loaded with P28 peptide, alone or in combination with vascular endothelial growth factor (VEGF), to evaluate the effect of dual bioactive factor delivery. We hypothesized that CS-based scaffolds would optimize ceramic composition and co-delivery of P28 and VEGF, and can enhance early-stage osteogenic differentiation and support bone regeneration. The CS-based scaffolds were characterized by their physicochemical properties, including swelling behavior, mechanical strength, porosity, and in vitro degradation. Biological evaluations were performed including cell proliferation assays, ALP activity, ARS staining, and RT-qPCR, to assess osteogenic differentiation. The results showed that the scaffolds had high porosity, excellent swelling behavior, and degraded within 8 weeks. Dual delivery of P28 and VEGF significantly enhanced early osteogenic markers, indicating a complementary effect. These findings demonstrated that CS-based scaffolds with an optimized ceramic ratio and bioactive factor incorporation have the potential to facilitate bone regeneration. Full article

Polymer-modified bitumen is difficult to produce and often separates during storage and transport. In contrast, granular bitumen modifiers offer wide applicability, construction flexibility, and ease of transport and storage. This study involved preparing a multipolymer granulated bitumen modifier with a styrene–butadiene–styrene block copolymer, polyethylene, and aromatic oil. To elucidate the modification mechanism of a multipolymer granulated bitumen modifier on bitumen, the elemental composition of bitumen A and B, the micro-morphology of the modifiers, the changes in functional groups, and the distribution state of the polymers in the bitumen were investigated using an elemental analyzer, a scanning electron microscope, Fourier-transform infrared spectroscopy, and fluorescence microscopy. The effects of the multipolymer granulated bitumen modifier on the physical, rheological, and viscoelastic properties of two types of base bituminous binders were investigated at various dosages. The test results show that the Z_H/C ratio of base bitumen A is smaller than that of base bitumen B and that the cross-linking effect with the polymer is optimal. Therefore, the direct-feed modified asphalt of A performs better than the direct-feed modified asphalt of B under the same multipolymer granulated bitumen modifier content. The loose, porous surface structure of styrene–butadiene–styrene block copolymer promotes the adsorption of light components in bitumen, and the microstructure of the multipolymer granulated bitumen modifier is highly coherent. When the multipolymer granulated bitumen modifier content is 20%, the physical, rheological, and viscoelastic properties of the direct-feed modified asphalt of A/direct-feed modified asphalt of B and the commodity styrene–butadiene–styrene block copolymer are essentially identical. While the multipolymer granulated bitumen modifier did not significantly improve the performance of bitumen A/B at contents greater than 20%, the mass loss rate of the direct-feed modified asphalt of A to aggregate stabilized, and the adhesion effect reached stability. Image processing determined the optimum mixing temperature and time for multipolymer granulated bitumen modifier and aggregate to be 185–195 °C and 80–100 s, respectively, at which point the dispersion homogeneity of the multipolymer granulated bitumen modifier in the mixture was at its best. The dynamic stability, fracture energy, freeze–thaw splitting strength ratio, and immersion residual stability of bitumen mixtures were similar to those of commodity styrene–butadiene–styrene block copolymers with a 20% multipolymer granulated bitumen modifier mixing amount, which was equivalent to the wet method. The styrene–butadiene–styrene block copolymer bitumen mixture reached the same technical level. Full article

Glioblastoma (GBM) is the most aggressive and treatment-resistant primary brain tumor in adults. Despite current multimodal therapies, including surgery, radiation, and temozolomide chemotherapy, patient outcomes remain poor. Enhancing tumor radiosensitivity through biocompatible nanomaterials could provide a promising integrative strategy for improving therapeutic effectiveness. This study aims to evaluate the potential of bovine serum albumin-coated copper oxide nanoparticles (BSA@CuO-NPs) to enhance radiosensitivity in U87-MG cells under clinically relevant X-ray irradiation. In brief, BSA@CuO-NPs were synthesized via carbodiimide crosslinking and characterized by DLS, SEM, and zeta potential analysis. U87-MG cells were treated with BSA@CuO-NPs alone or in combination with X-ray irradiation (2 Gy). Cytotoxicity was assessed using the MTT assay, while radiosensitization was evaluated through clonogenic survival analysis. Apoptosis induction and DNA damage were analyzed via Annexin V staining and γ-H2AX immunofluorescence, respectively. The results revealed that BSA@CuO-NPs showed good colloidal stability and biocompatibility compared with uncoated CuO-NPs. When combined with irradiation, BSA@CuO-NPs significantly decreased clonogenic survival (p < 0.05) and increased apoptotic cell death compared to irradiation alone. Immunofluorescence demonstrated increased γ-H2AX focus formation, indicating higher DNA double-strand breaks in the combination group. In conclusion, BSA@CuO-NPs enhance the effects of ionizing radiation by increasing DNA damage and apoptosis in U87-MG cells, indicating their potential as combined radiosensitizers. These results support further research into albumin-coated metal oxide nanoparticles as adjuncts to standard radiotherapy for the management of GBM. One challenge in this context is the effective delivery of nanoparticles to GBM. However, the stability of BSA@CuO-NPs in physiological solutions could help overcome this obstacle. Full article

Background/Objectives: Group B Streptococcus (GBS) is a significant cause of perinatal infection in neonates and infants. Complications could include neonatal sepsis and meningitis, preterm birth, stillbirth, or death. Though no GBS vaccine is currently licensed, maternal immunization is expected to be a highly effective strategy to address invasive GBS disease—particularly in low- and middle-income countries (LMICs), where the disease burden is the greatest and access to existing interventions is limited. In this study, we present a novel hexavalent GBS vaccine candidate with a unique combination of serotypes (ST)—Ia, Ib, II, III, V, and VII—that could be an efficacious and cost-effective intervention, with the broadest coverage of 99% against circulating serotypes globally. Methods: The 6-valent conjugate vaccine candidate, GBS-06, is developed using a novel approach by linking the six polysaccharides (PS) to recombinant cross-reactive material 197 (rCRM197) carrier protein derivatized with a hydrazide-polyethylene glycol-hydrazide (HZ-PEG-HZ) linker. A repeat-dose GLP toxicology study with GBS-06 was conducted at the highest clinical dose of 20 µg in rabbits with saline as the placebo control. Results: The results reveal induction of robust anti-capsular polysaccharide-specific IgG responses against each of the six serotypes after each dose with the highest antibody GMCs at Day 49 following the third dose. Conclusions: Hence, this work is the first demonstration of strong immunogenicity achieved using a linker (HZ-PEG-HZ) for GBS glycoconjugate vaccine development. The positive data from the study have strong implications in the advancement of the candidate for evaluation in clinical trials and provide a licensure pathway for maternal immunization. Full article

The chlorinated polyvinyl chloride (CPVC)/acrylonitrile–butadiene–styrene (ABS) composite represents an important class of engineering thermoplastics, offering a strong balance of flame retardancy, chemical resistance, mechanical properties, processability, and cost efficiency. Despite its widespread application, the flame-retardant mechanism in the CPVC/ABS system remains poorly understood. This work systematically investigated the non-monotonic flame-retardant behavior of CPVC/ABS composites through comprehensive characterization. The combustion performance, as determined by limiting oxygen index (LOI), UL-94 vertical burning tests, and cone calorimeter tests (CCTs), showed an unexpected pattern of flame retardancy initially improving then decreasing with reduced ABS content, which contradicted conventional expectations. The optimal composition at a CPVC/ABS ratio of 2:3 demonstrated good performance, achieving a UL-94 5VA rating and 47.3% reduction in total heat release (THR) relative to CPVC. A more stable and compact structure was observed from the morphology analysis of the residual char, and the thermogravimetric analysis further revealed a synergistic effect in carbonization behavior. The above flame-retardant mechanism could be interpreted by the combined effects of accelerated char formation during the early decomposition stage and significantly enhanced char crosslinking degree. These findings provided fundamental insights for designing high-performance flame-retardant polymer composites and facilitating their industrial implementation. Full article

Poly(2-oxazoline) coatings with antibiofouling properties and good biocompatibility can also be deposited by the plasma polymerization method using 2-methyl-2-oxazoline and 2-ethyl-2-oxazoline as monomers. Plasma polymers are formed of various monomer fragments and recombination products. Commonly, plasma polymers are highly crosslinked structures created by many different fragments, preferably of no repeating unit. Thus, chemical analysis of plasma polymers is difficult. To obtain a better description of plasma polymerized poly(2-oxazoline) coatings, the analysis of their plasma deposition process was performed. The electron ionization of 2-methyl-2-oxazoline and 2-ethyl-2-oxazoline molecules was studied using the crossed electron–molecular beam technique with mass spectrometric detection of the produced ions. The chemical composition of gaseous compounds at plasma polymerization was determined by gas chromatography-mass spectrometry (GC-MS), ion mobility spectrometry (IMS) and optical emission spectroscopy (OES). Also, the chemical composition and antibacterial activity of the water leachates from previously deposited poly(2-oxazoline) films were tested using FTIR spectroscopy and the disk diffusion method, respectively. It was found that acetonitrile and propionitrile are the main neutral products created in the nitrogen discharge with 2-methyl-2-oxazoline and 2-ethyl-2-oxazoline monomers. The water leachates from deposited films do not exhibit any antibacterial activity. It was concluded that the antibacterial properties of POx films are due to their hydrophility. Full article

This study aims to address the poor extensibility, brittleness, and limited hydration stability of pure sodium alginate (SA) hydrogels, which hinder their use in flexible, skin-adherent applications such as facial masks, by developing bio-based composites incorporating five representative functional additives: xanthan gum, guar gum, hydroxyethyl cellulose (HEC), poly(ethylene glycol)-240/hexamethylene diisocyanate copolymer bis-decyl tetradeceth-20 ether (GT-700), and Laponite^® XLG. Composite hydrogels were prepared by blending 1.5 wt% SA with 0.3 wt% of each additive in aqueous humectant solution, followed by ionic crosslinking using 3% (w/w) CaCl₂ solution. Physicochemical characterization included rotational viscometry, uniaxial tensile testing, ATR-FTIR spectroscopy, swelling ratio analysis, and pH measurement. Among them, the SA/XLG composite exhibited the most favorable performance, showing the highest viscosity, shear-thickening behavior, and markedly enhanced extensibility with an elongation at break of 14.8% (compared to 2.5% for neat SA). It also demonstrated a mean swelling ratio of 0.24 g/g and complete dissolution in water within one year. ATR-FTIR confirmed distinct non-covalent interactions between SA and XLG without covalent modification. The hydrogel also demonstrated excellent conformability to complex 3D surfaces, consistent hydration retention under centrifugal stress (+23.6% mass gain), and complete biodegradability in aqueous environments. Although its moderately alkaline pH (8.96) may require buffering for dermatological compatibility, its mechanical resilience and environmental responsiveness support its application as a sustainable, single-use skin-contact material. Notably, the SA/XLG composite hydrogel demonstrated compatibility with personalized fabrication strategies integrating 3D scanning and additive manufacturing, wherein facial topography is digitized and transformed into anatomically matched molds—highlighting its potential for customized cosmetic and biomedical applications. Full article

Well-killing operations in water-sensitive hydrophilic formations are often complicated by extended well clean-up periods and, in some cases, failure to restore the well’s production potential post-kill. Typical development targets exhibiting these properties include the Neocomian and Jurassic deposits of fields in Western Siberia and Western Kazakhstan. This paper proposes a well-killing method incorporating simultaneous near-wellbore treatment. In cases where heavy oil components (asphaltenes, resins, or paraffins) are deposited in the near-wellbore zone, their removal with a solvent results in post-operation flow rates that exceed pre-restoration levels. For wells not affected by asphaltene, resin, and paraffin deposits, killing is performed using a blocking pill of invert emulsion stabilized with an emulsifier and hydrophobic nanosilica. During filtration into the formation, this emulsion does not break but rather reforms according to the pore throat sizes. Flow rates in such wells typically match pre-restoration levels. The described engineering solution proves less effective when the well fluid water cut exceeds 60%. For wells exhibiting premature water breakthrough that have not yet produced their estimated oil volume, the water source is identified, and water shutoff operations are conducted. This involves polymer-gel systems crosslinked with resorcinol and paraform, reinforced with inorganic components such as chrysotile microdispersions, micro- and nanodispersions of shungite mineral, and gas black. Oscillation testing identified the optimal additive concentration range of 0.6–0.7 wt%, resulting in a complex modulus increase of up to 25.7%. The most effective polymer-inorganic composite developed by us, incorporating gas black, demonstrates high water shutoff capability (residual resistance factor ranges from 12.5 to 65.0 units within the permeability interval of 151.7 to 10.5 mD). Furthermore, the developed composites exhibit the ability to selectively reduce water permeability disproportionately more than oil permeability. Filtration tests confirmed that the residual permeability to oil after placing the blocking composition with graphene is 6.75 times higher than that to water. Consequently, such treatments reduce the well water cut. Field trials confirmed the effectiveness of the developed polymer-inorganic composite systems. Full article

Considering the high stability of water-in-oil (W/O) emulsions, contamination from emulsified pollutants poses a long-term risk to the environment. In this study, hybrid membranes composed of wheat gluten amyloid fibrils (WGAFs) and zein nanoparticles (ZNPs) were prepared and used as a separator to remove emulsified W/O droplets from the oily phase. ZNPs and WGAFs were synthesized through antisolvent method and fibrillation process. Next, a ZNP-functionalized wheat gluten AF/methyl cellulose (ZNP-WGAF/MC) hybrid membrane was fabricated, and its properties were investigated via various analytical techniques. Lastly, the separation efficiency of the ZNP-WGAF/MC hybrid membrane for various W/O emulsions was assessed using microscopy and light scattering. The formation of ZNPs or WGAFs was first verified via spectroscopic and microscopic methods. Our results indicated that the ZNP-WGAF/MC hybrid membranes were synthesized via chemical crosslinking coupled with the casting method. Furthermore, the incorporation of either WGAFs or ZNPs was found to improve the thermal stability and surface hydrophobicity of membranes. Finally, the separation efficiency of the ZNP-WGAF/MC hybrid membranes for various W/O emulsions was determined to be ~87–99%. This research demonstrates the potential of harnessing three-dimensional membranes composed of plant protein-based fibrils and nanoparticles to separate emulsified W/O mixtures. Full article

Background/Objectives: DNA-damaging agents can contribute to genetic instability, and such agents are often used in cancer chemotherapeutic regimens due to their cytotoxicity. Thus, understanding the mechanisms involved in DNA damage processing can not only enhance our knowledge of basic DNA repair mechanisms but may also be used to develop improved chemotherapeutic strategies to treat cancer. The high-mobility group box protein 1 (HMGB1) is a known nucleotide excision repair (NER) cofactor, and its family member HMGB3 has been implicated in chemoresistance in ovarian cancer. Here, we aim to understand the potential role(s) of HMGB3 in processing DNA damage. Methods: A potential role in NER was investigated using HMGB3 knockout human cell lines in response to UV damage. Subsequently, potential roles in DNA interstrand crosslink (ICL) and DNA double-strand break (DSB) repair were investigated using mutagenesis assays, metaphase spreads, foci formation, a variety of DNA repair assays, and TagSeq analyses in human cells. Results: Interestingly, unlike HMGB1, HMGB3 does not appear to play a role in NER. We found evidence to suggest that HMGB3 is involved in the processing of both DSBs and ICLs in human cells. Conclusions: These novel results elucidate a role for HMGB3 in DNA damage repair and, surprisingly, also indicate a distinct role of HMGB3 in DNA damage repair from that of HMGB1. These findings advance our understanding of the role of HMGB3 in chemotherapeutic drug resistance and as a target for new chemotherapeutic strategies in the treatment of cancer. Full article

The development of advanced wound dressing materials with enhanced antibacterial properties is critical for improving patient outcomes and reducing infection risks. This study introduces a novel bio-based aerogel composed of copper-crosslinked alginate and hyaluronic acid, synthesized using supercritical gel drying techniques. Alginate and hyaluronic acid polymers are widely used in the pharmaceutical and medical industries because of their nontoxicity, biodegradability, and biocompatibility. This study aimed to create an aerogel that could be used as a potential wound dressing material by crosslinking hyaluronic acid and alginate with copper. The bio-based aerogel was prepared by ionic gelation and supercritical gel drying. The prepared materials were characterized using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), BET surface area analysis, and energy-dispersive X-ray fluorescence (XRF). Moreover, the aerogel wound dressing properties were evaluated in terms of fluid uptake and antibacterial activity against S. aureus and E. coli. The physicochemical characterization of the prepared aerogels revealed their unique structural and morphological features, which are influenced by copper ion concentration and crosslinking time. Regarding their wound dressing evaluation, both aerogel and hydrogel were found to have antibacterial properties when tested on S. aureus with inhibition zones of (36 mm, 23 mm) and E. coli (31.6 mm, 21 mm) for hydrogel and aerogel, respectively. Also, excellent fluid uptake was found to reach up to 743%. These findings underscore the potential of copper-crosslinked alginate–hyaluronic acid aerogels as innovative wound dressing materials that combine superior antibacterial efficacy with excellent fluid management, paving the way for improved wound healing solutions. Full article

Enzyme entrapment in alginate hydrogel microbeads is an effective method of immobilization for industrial applications, but many fabrication methods for alginate microbeads involve oil, organic solvents, or high temperatures that reduce enzymatic activity. In this study, we employed an oil- and solvent-free gas-shearing technique to prepare alginate microbeads for the entrapment of Candida rugosa lipase (CRL), thereby minimizing thermal- and solvent-induced inactivation. To enhance immobilization efficiency and reusability, the effects of gas flow rate, alginate concentration, and cross-linking metal ions were systematically investigated. CRL entrapped in Ba- and Fe-alginate microbeads showed superior immobilization yield, activity retention, and activity recovery compared with CRL entrapped in conventional Ca-alginate microbeads. Notably, both Ba- and Fe-alginate microbeads exhibited significantly enhanced stability, with half-lives up to 127-fold greater than that of free CRL at 60 °C, and maintained substantially higher pH stability across the tested range. Ba-alginate microbeads provided greater pH stability and substrate affinity, whereas Fe-alginate microbeads demonstrated enhanced thermal stability and catalytic turnover. These findings highlight gas-shearing as a scalable and gentle fabrication method for producing high-performance alginate microbeads with tunable properties, making them suitable for enzyme entrapment in diverse biocatalytic applications. Full article

Treating brain cancer remains challenging due to the blood–brain barrier (BBB) and the systemic toxicity of chemotherapy. This study focuses on developing human serum albumin (HSA) nanoparticles modified with low-molecular-weight protamine (LMWP) to improve crossing the BBB and enable targeted delivery of curcumin and temozolomide (TMZ). Nanoparticle stability was enhanced by crosslinking with aldehyde groups from oxidized gellan (OG). The successful attachment of LMWP to HSA at the thiol group of Cys34 was confirmed through FT-IR and ¹H-NMR analyses. Most self-assembled nanoparticles were smaller than 200 nm in diameter. Curcumin showed higher encapsulation efficiency than TMZ. In vitro drug release was pH-dependent: curcumin released more at pH 7.4, while TMZ release was better at pH 4. Higher crosslinking degrees reduced drug release. Cytotoxicity assays on V79-4 (normal) and C6 (glioma) cell lines showed increased apoptosis and significantly lower IC₅₀ values for co-encapsulated formulations, indicating a synergistic effect. Curcumin’s antioxidant activity was maintained and protected from UV degradation by the polymer matrix. The parallel artificial membrane permeability assay (PAMPA) confirmed that the functionalized formulations with co-encapsulated drugs could cross the BBB. Hemocompatibility studies indicated a favorable profile for intravenous use. Full article