Search Results (24)

Egg quality during storage is a critical factor influencing consumer acceptance and food safety. However, the effects of storage methods on eggshell translucency and surface microbiota remain insufficiently understood. In this study, three common packaging methods, paper pulp trays (PPT), expanded polyethylene foam trays (EPE), and transparent plastic boxes (TPB), were evaluated to assess their impact on egg translucency, internal quality, and microbial communities. Egg quality traits were measured, and microstructural and elemental characteristics were examined using scanning electron microscopy and compositional analysis. In addition, 16S rRNA sequencing was performed to characterize the eggshell surface microbiota. The packaging method significantly influenced translucency development, with EPE mitigating mottling better than PPT and TPB. Storage duration was the predominant driver of internal quality deterioration, particularly affecting the albumen height and Haugh units. Translucency was not associated with shell thickness or mineral content but was likely associated with moisture dynamics. Distinct microbial communities are shaped by different packaging materials. These findings provide new insights into the mechanisms underlying translucency and microbial ecology during egg storage. This highlights the practical implications of optimizing packaging strategies to maintain egg quality, extend the shelf life, and ensure microbial safety. Full article

The environmental persistence of post-consumer plastics remains a critical challenge due to their chemical stability, the presence of additives, and prior environmental weathering. This study evaluates the partial biodegradation and chemical transformation of post-consumer low-density polyethylene (LDPE) and expanded polystyrene (EPS) by Tenebrio molitor larvae under uncontrolled environmental conditions. Four diets were tested, including LDPE+S and EPS+S (polymers supplemented with wheat bran), to assess the influence of a co-substrate on larval performance and polymer transformation. Fourier-transform infrared spectroscopy (FTIR) revealed the emergence of oxygen-containing functional groups (–OH and C=O) in the frass, which were absent or negligible in pristine materials, indicating oxidative modification of the polymer matrix. Gel permeation chromatography (GPC) revealed pronounced reductions in number-average molecular weight (Mn) and increased polydispersity for EPS-derived fractions, consistent with heterogeneous chain scission and partial depolymerization. For LDPE, GPC evidenced the formation of THF-soluble, low-molecular-weight polymer-derived fragments, indicating fragmentation despite the inability to quantify pristine LDPE due to its insolubility in the mobile phase. Gas chromatography–mass spectrometry (GC–MS) identified aromatic hydrocarbons, phthalate esters, organosiloxanes, and fatty acid derivatives, reflecting both degradation intermediates and migrated additives from post-consumer plastics. Together, these results provide integrated evidence that Tenebrio molitor can induce chemical transformation of post-consumer LDPE and EPS under non-controlled environmental conditions, offering mechanistic insight into a biologically mediated degradation pathway that is directly relevant to realistic plastic waste scenarios. Full article

The proliferation of single-use petroleum-based foams in protective packaging has become a major source of persistent plastic waste, posing significant challenges to environmental sustainability. To address this issue, we developed a fully biodegradable cushioning foam from bamboo, a rapidly renewable biomass, using an environmentally benign deep eutectic solvent (DES) process that avoids harsh chemical bleaching. The resulting lignin-containing cellulose nanofibril (LCNF)/sodium alginate (SA) foam exhibits low density (0.23 g/cm³), high compressive strength (0.24 MPa at 70% strain), and excellent elasticity (90% recovery at 50% strain), enabled by a dual-network structure of Ca²⁺-crosslinked SA and entangled LCNFs. Critically, the material is fully compostable and leaves no microplastic residues, offering a circular end-of-life pathway. In real-world banana drop tests, it matched the performance of commercial expanded polyethylene (EPE) while outperforming polyethylene bubble wrap. This work demonstrates a practical, scalable route to replace fossil-derived cushioning materials with a bio-based alternative that aligns with the principles of cleaner production and circular economy. Full article

Microwave-assisted heating (MWH) has established itself as a transformative and energy-efficient paradigm for advanced materials processing. This review provides a comprehensive overview of the advances achieved at the CNR-SCITEC laboratories in Genoa. In this context, a customized microwave platform has been strategically employed for the synthesis, sintering, foaming, and melting of diverse inorganic, organic, and hybrid systems. The spectrum of materials investigated includes superconducting magnesium diboride (MgB₂), hydroxyapatite-based scaffolds, polyethylene components obtained via microwave-assisted rotational molding, cork-based sound-adsorbing composites, recycled expanded polystyrene (rEPS) panels, and polyvinylidene fluoride (PVDF) piezoelectric films. Across the case studies, MWH demonstrated a superior capacity for reducing energy consumption and processing times while maintaining—or even enhancing—the target functional properties. Furthermore, this work evaluates the technological maturity and emerging market opportunities of microwave-based processing, positioning it as a key and sustainable platform for next-generation materials development. Full article

Mechanical coffee drying is an energy-intensive stage of postharvest processing that directly affects product quality and production costs. This study evaluated the technical and economic feasibility of using expanded polystyrene (EPS) as a thermal insulation material to improve the performance of a mechanical coffee dryer and to demonstrate its potential for sustainable reuse. Experiments were conducted using a total of 210 kg of wet parchment coffee (Coffea arabica L. var. Cenicafé 1) per treatment, corresponding to three experimental replicates of 70 kg each, dried at 50 ± 2 °C, comparing an EPS-insulated dryer (0.02 m thickness) with a non-insulated control. A theoretical model based on steady-state heat transfer through series resistances estimated energy losses and system efficiency for different insulating materials. Theoretical results indicated that EPS, polyethylene foam, and cork reduced heat losses by 58.1%, 54.3%, and 50.9%, respectively. Experimentally, EPS reduced drying time by 7.82%, fuel consumption by 13.9%, and energy demand by 9.5%, while increasing overall efficiency by 6.7% and reducing wall heat losses by 37.7%. Improved temperature stability enhanced heat retention and moisture migration behavior. Economically, EPS reduced operating costs, yielding annual savings of USD 81.5, a 0.45-year payback period, and an annual return on investment (ROI) of 10.86, confirming its viability as a cost-effective and sustainable solution for improving energy efficiency in mechanical coffee drying. Full article

Bangladesh generates approximately 3000 tons of plastic waste daily, and high mismanagement leads to substantial discharge into soils, rivers, and oceans. Limited research exists on plastic pollution along Cox’s Bazar in southeastern Bangladesh, with no studies spanning the entire coast; this study provides the first comprehensive assessment of the full coastline. This study investigates the abundance, types, and distribution of macro-, meso-, and microplastics in sediments from 23 stations covering Tourism, Active, and Less Active areas. Plastics were classified by size, shape, color, and polymer composition using stereomicroscopy and Fourier Transform Infrared Spectroscopy (FTIR), while spatial patterns of microplastic polymers were analyzed using Inverse Distance Weighted (IDW) interpolation. A total of 11,558 plastic particles were identified, with microplastics dominating (409.04 particles/m²), followed by mesoplastics (60.7 particles/m²) and macroplastics (32.8 particles/m²). Expanded polystyrene (EPS) and fragments were the most prevalent shapes, while transparent-white particles dominated in color. Polystyrene (PS), polypropylene (PP), and polyethylene (PE) comprised over 95% of polymers. IDW mapping highlighted Tourism, urban, and industrial zones as microplastic hotspots, with higher abundances in tourism areas. These findings provide a baseline for monitoring coastal plastic pollution and emphasize improved plastic management and recycling, contributing globally to understanding contamination in rapidly urbanizing, tourism-driven developing regions. Full article

Engineering structures often face safety risks under impact or explosion loading, making the design of lightweight and efficient cushioning systems crucial. This study investigates the dynamic response and energy-dissipation characteristics of Expanded Polystyrene (EPS), Expanded Polyethylene (EPE), and soil–foam composite cushion layers under impact loading, using a Split Hopkinson Pressure Bar (SHPB) testing apparatus. The tests include pure foam layers (lengths ranging from 40 to 300 mm) and a soil–foam composite layer with a total length of 60 mm (soil/foam ratio 1:1 to 1:3), subjected to impact velocities of 9.9–15.4 m/s. The results show that the stress wave propagation velocity of EPE is 149.6 m/s, lower than that of EPS at 249.3 m/s. At higher velocities, the attenuation coefficient for the 40 mm EPE sample reaches as low as 0.22, while EPS is 0.31. Furthermore, the maximum energy absorption coefficient of EPE exceeds 98%, with better stability at high impact velocities. In composite cushion layers, both soil and foam collaborate in energy absorption, but an increased proportion of soil leads to a decrease in energy absorption efficiency and attenuation capacity. Under equivalent ratios, the soil–EPE combination performs better than the soil–EPS combination. By constructing a comprehensive evaluation system based on three indices: stress wave attenuation coefficient, energy absorption coefficient, and energy absorption density, this study quantifies the impact resistance performance of different cushioning layers, providing theoretical and parametric support for material selection in engineering design. Full article

In rockfall hazard mitigation, geofoam has been used in the cushion layer to improve the sustainability of the rockfall gallery, such as impact resistance enhancement and dead load reduction. Impact tests were conducted to study the effect of geofoam type, thickness, and impact energy on the impact responses of the sand cushion layer. The test results showed that placing geofoam in the sand cushion can reduce the peak impact force of the rockfall and the peak acceleration of the gallery slab by up to 80%. While the peak impact stress at the cushion layer bottom can also be reduced by geofoam under low impact energy, thicker geofoam layers (e.g., 4 and 6 cm) increased peak impact stress when the rockfall had high impact energy. Placing geofoam at the bottom of the cushion to replace one third of the sand cushion thickness can enhance the impact resistance of the cushion layer. Under low impact energy, expandable polyethylene (EPE) foam resulted in lower impact force on the rockfall, reduced impact stress within the sand cushion, and diminished vibration of the gallery slab compared with polystyrene (EPS) foam with a constant thickness. However, EPS foam is suitable for use in sand cushions of rockfall galleries subjected to high-energy rock impacts. Moreover, EPE foam exhibits superior resilience, resulting in less damage compared to EPS foam. Full article

In the design of structures involving quasi-brittle materials such as concrete, it is essential to consider the scale dependence of the mechanical properties of the material. Among the theories used to describe the phenomenon of size effect, the fractal theory proposed by Carpinteri and colleagues has attracted attention for its results in the last three decades of research. The present study employs the fractal perspective to examine the scale effect in three-point bending tests conducted on expanded polyethylene (EPS) beam specimens. The influence of size on flexural strength, fracture energy, and critical angle of rotation is investigated. Additionally, numerical simulations based on peridynamic (PD) theory are performed based on the experimental tests. The global behavior, brittleness, failure configuration, and fractal scale effect obtained numerically are evaluated. The numerical results show a good correlation with the experimental ones and, moreover, both the experimental and numerical results are in agreement with the fractal theory of scale effect. More precisely, the error of the sum of the fractal exponents, computed with respect to the theoretical one, is equal to −1.20% and −2.10% for the experimental and numerical results, respectively. Moreover, the classical dimensional analysis has been employed to demonstrate that the scale effect can be naturally described by the PD model parameters, allowing to extend the results for scales beyond those analyzed experimentally. Full article

In this work, a comprehensive characterization of microplastic samples collected from unique geographical locations, including the Mediterranean Sea, Strait of Gibraltar, Western Atlantic Ocean and Bay of Biscay utilizing advanced hyperspectral imaging (HSI) techniques working in the short-wave infrared range (1000–2500 nm) is presented. More in detail, an ad hoc hierarchical classification approach was developed and applied to optimize the identification of polymers. Morphological and morphometrical attributes of microplastic particles were simultaneously measured by digital image processing. Results showed that the collected microplastics are mainly composed, in decreasing order of abundance, by polyethylene (PE), polypropylene (PP), polystyrene (PS) and expanded polystyrene (EPS), in agreement with the literature data related to marine microplastics. The investigated microplastics belong to the fragments (86.8%), lines (9.2%) and films (4.0%) categories. Rigid (thick-walled) fragments were found at all sampling sites, while film-type microplastics and lines were absent in some samples from the Mediterranean Sea and the Western Atlantic Ocean. Rigid fragments and lines are mainly made of PE, whereas PP is the most common polymer for the film category. Average Feret diameter of microplastic fragments decreases from EPS (3–4 mm) to PE (2–3 mm) and PP (1–2 mm). The setup strategies illustrate that the HSI-based approach enables the classification of the polymers constituting microplastic particles and, at the same time, to measure and classify them by shape. Such multiple characterization of microplastic samples at the individual level is proposed as a useful tool to explore the environmental selection of microplastic features (i.e., composition, category, size, shape) and to advance the understanding of the role of weathering, hydrodynamic and other phenomena in their transport and fragmentation. Full article

Microplastics (MPs) have attracted considerable attention as one of the most remarkable food and drink pollutants in recent years. Disposable cups, which are widely used as single-use containers, have been suspected as the primary sources of MPs found in cold and hot beverages. In this study, the effect of different exposure times (0, 5, 10 and 20 min) and temperatures (4 °C, 50 °C and 80 °C) on MP release from the single-use cups made of four different materials [polypropylene (PP), polystyrene (PS), polyethylene (PE) coated paper cups and expanded polystyrene (EPS)] into the water was investigated. The number of MPs ranged from 126 p/L to 1420 p/L, while the highest and lowest counts were observed in the PP (50 °C for 20 min) and PE-coated paper cups (4 °C 0 min), respectively. Washing the cups with ultrapure water prior to use reduced the MP release by 52–65%. SEM images demonstrated the abrasion on the surface of the disposable cups as a result of hot water exposure. Intensities of FTIR absorbance levels at some wavelengths were decreased by the water treatment, which could be evidence of surface abrasion. The annual MP exposure of consumers was calculated as 18,720–73,840 by the consumption of hot and cold beverages in disposable cups. In conclusion, as the level and potential toxicity of MP exposure in humans are not yet fully known, this study sheds light on the number of MPs transferred to cold and hot beverages from single-use disposable cups. Full article

This paper describes the results of an experimental assessment of the thermal conductivity of pipe insulation. The need for reducing energy loss in industrial piping systems makes the availability of relevant and reliable insulation materials of special importance. Several specimens of pipe laggings, made of different materials, including mineral wool, polyethylene foam (PEF), expanded polystyrene (EPS), flexible elastomeric foam (FEF) and polyurethane foam (PUR), were tested in accordance with the European standard ISO 8497. The thermal conductivity of the materials was measured for a wide range of temperatures. The results were compared with the values reported in the technical specifications as well as with the literature data. The assessment of measurement uncertainty was also described. The results showed that, in a few cases, thermal conductivity turned out to be greater than that declared by the manufacturer by as much as over 10%. Full article

In this study, a comparative life cycle assessment of three different products with reusable and single-use packaging for fresh food distribution was conducted. For the reusable packaging, one utilized a vacuum insulation panel (VIP) box made of recycled polyethylene terephthalate (r-PET), while the other employed expanded polyethylene (EPE). For comparison, a disposable box made of widely used expanded polystyrene (EPS) was selected. We analyzed the environmental impacts of production, transportation, reprocessing (reused boxes), and disposal in 18 impact categories. As a result of analyzing the actual reuse of 300 rounds of fresh food, the cumulative global warming potential (GWP) values of the VIP and EPE box were 136.58 kg carbon dioxide (CO₂) eq and 281.72 kg CO₂ eq, respectively, 87% and 74% lower than those of the EPS box. Additionally, the GWP values were the same as those of the EPS boxes when the VIP and EPE boxes were reused 7 and 12 times, respectively. The best-case scenario was revealed when the reusable packaging with the r-PET VIP was compared with the EPE and EPS boxes. In conclusion, reusable packaging is expected to contribute to the reduction in the environmental burden and better suit global environmental requirements for sustainable food distribution and related industries. In addition, our findings can inform policy and industry decisions to promote more sustainable practices in the food industry, contributing to the advancement of sustainability in this field. Full article

In the process of logistics, shock and vibration are the most important factors contributing to product damage. Assembling honeycomb paperboard and EPE is commonly used to provide cushioning and anti-vibration effects to materials. Therefore, it is necessary to study the vibration transmission properties of this kind of assembly in the anti-vibration process. The aim of this paper was to experimentally determine the vibration transmission properties of assemblies with honeycomb paperboard and expanded polyethylene (EPE). Through a sinusoidal sweep vibration test of this assembly, the vibration transmission characteristic curves of assemblies with honeycomb paperboard and EPE of different thicknesses were obtained and compared. Assuming the assembly and mass block as a single degree of freedom with a small damping linear system, the damping energy dissipation of the assembly and the resonance frequency were obtained. The vibration transmission property curves of the assembly can be divided into four regions. With an excitation acceleration of 0.5 g and a honeycomb paperboard with a thickness of 60 mm (F60), the vibration transmission rate and the resonance frequency—of the material dampened with EPE at a thickness of 60 mm (E60), and the assembly (F30/E30) with a 30 mm thick honeycomb paperboard and 30 mm thick EPE—increased by −2.5% and −17.5%, −86.9% and 79.3%, and −95.9% and −85.7%, respectively. Compared to the assembly with 20 mm thick honeycomb and 20 mm thick EPE (F20/E20), the vibration transmission rate, the resonance frequency, and the material damping and damping energy dissipation of F40/E20, F30/E30, and F20/E40 increased by 75.6%, 48.3%, and 66.1%; 1.2%, −21.5%, and −38.9%; 241.5%, 82.8%, and 13.3%; and 12.5%, 98.9%, and 106.8%, respectively. Compared to F60 and E60, the damping energy dissipation of F30/E30 increased by 2816.7% and 133.3%, respectively. The assembly of F30/E30 has the smallest vibration transmission rate and the most vibration energy dissipation among these assemblies. This means that the assembly of F30/E30 absorbs the most external vibration energy, while the acceleration that is transmitted to the internal product is minimal. Therefore, in the design of cushioning packaging, according to the characteristics and natural frequency of the internal products, an appropriate assembly can be selected, which should have a lower vibration transmission rate and more vibration energy dissipation, and should not resonate with the internal product. This will provide a theoretical basis for the design of cushioning packaging. Full article

Chronic wounds have been a global health risk that demands intensive exploration. A tri-layered biomaterial scaffold has been developed for skin wounds. The top layer of the scaffold is superhydrophobic, and the bottom layer is hydrophilic, both of which were electrospun using recycled expanded polystyrene (EPS) and monofilament fishing line (MFL), respectively. The intermediate layer of the scaffold comprised hydrogel by cross-linking chitosan (CS) with polyethylene glycol. The surface morphology, surface chemistry, thermal degradation, and wettability characteristics of each layer of the scaffold were examined. Also, the antibacterial activity and in vitro cytotoxicity study on the combined tri-layered scaffold were assessed against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). Data revealed exceptional water repellency of the heat-treated electrospun top superhydrophobic layer (TSL) with a high-water contact angle (WCA) of 172.44°. A TSL with 15 wt% of micro-/nano-inclusions had the best thermal stability above 400 °C. The bottom hydrophilic layer (BHL) displayed a WCA of 9.91°. Therapeutically, the synergistic effect of the combined tri-layered scaffold significantly inhibited bacteria growth by 70.5% for E. coli and 68.6% for S. aureus. Furthermore, cell viability is enhanced when PEG is included as part of the intermediate CS hydrogel layer (ICHL) composition. Full article