Search Results (71)

In this paper, the evaluation of the mechanical performance of novel, designed topologically optimized shin pads with advanced materials will be conducted with the aid of Finite Element Analysis (FEA) to assess the endurance of the final structure on impact phenomena extracted from actual real-life data acquired from contact sports. The main focus of the developed prototype is to have high-enough energy absorption capabilities and vibration isolation properties, crucial for the development of trustworthy protective equipment. The insertion of advanced materials with controlled weight fractions and lattice geometries aims to strategically improve those properties and provide tailored characteristics similar to the actual human skeleton. The final design is expected to be used as standalone protective equipment for athletes or as a protective shield for the development of human lower limb prosthetics. In this context, computational investigation of the dynamic mechanical response was conducted by replicating a real-life phenomenon of the impact during a contact sport in a median condition of a stud kick impact and an extreme case scenario to assess the dynamic response under shock-absorption conditions and the final design’s structural integrity by taking into consideration the injury prevention capabilities. The results demonstrate that the proposed lattice geometries positively influence the injury prevention capabilities by converting a severe injury to light one, especially in the gyroid structure where the prototype presented a unified pattern of stress distribution and a higher reduction in the transmitted force. The incorporation of the PA-12 matrix reinforced with the reused ground tire rubber results in a structure with high enough overall strength and crucial modifications on the absorption and damping capabilities vital for the integrity under dynamic conditions. Full article

This work evaluates a hydrogen-fueled planar micro-combustor featuring three triply periodic minimal surface (TPMS) structures, namely, gyroid, lidinoid, and Neovius matrix lattices, aiming to advance heat transfer processes and enhance system efficiency in micro-thermophotovoltaic (MTPV) applications. Through three-dimensional numerical investigations, a series of simulations are conducted under varying TPMS lengths, inlet volume flow rate, and inlet equivalence ratios to optimize the design and operating conditions. The outcomes reveal that increasing the length of the TPMS structures is an effective means of improving heat transfer from the combustion zone to the walls, as indicated by significant increases in both mean wall temperature and radiation efficiency. However, longer internal structures reduce the uniformity of wall temperature and slightly increase entropy generation. Of the three topologies, the Neovius lattice demonstrates superior performance in all length scales, exhibiting a marginal improvement over the gyroid and a substantially greater advantage over the lidinoid structure. Increasing the inlet volume flow rate enhances wall temperature and its uniformity; however, the performance parameters decrease for all structures, indicating a limitation of the micro-combustor in benefiting from higher input power. Notably, the gyroid structure shows a lower rate of performance degradation at higher velocities, making it a potentially ideal design under such conditions. Finally, varying the equivalence ratio identifies the stoichiometric condition as optimal, yielding superior performance metrics compared to both lean and rich mixtures. Full article

This review paper deals with Triply Periodic Minimal Surfaces (TPMS) and lattice structures as a new generation of heat exchangers. Especially, their manufacturing is becoming feasible with technological progress. While some intricate structures are fabricated, challenges persist concerning manufacturing limitations, cost-effectiveness, and performance under transient operating conditions. Studies reported that these complex geometries, such as diamond, gyroid, and hexagonal lattices, outperform traditional finned and porous materials in thermal management, particularly under forced and turbulent convection regimes. However, TPMS necessitates the optimization of geometric parameters such as cell size, porosity, and topology stretching. The complex geometries enhance uniform heat exchange and reduce thermal boundary layers. Moreover, the integration of high thermal conductivity materials (e.g., aluminum and silver) and advanced coolants (including nanofluids and ethylene glycol mixtures) further improves performance. However, the drawback of complex geometries, confirmed by both numerical and experimental investigations, is the critical trade-off between heat transfer performance and pressure drop. The potential of TPMS-based heatsinks transpires as a trend for next-generation thermal management systems, besides identifying key directions for future research, including design optimization, Multiphysics modeling, and practical implementation. Full article

This study investigates the influence of geometric parameters of a gyroid lattice structure on the thermal performance of internal cooling channels relevant to gas turbine blade design. Various gyroid configurations were analyzed using CFD simulations in ANSYS CFX to evaluate heat transfer effectiveness (Nusselt number), cooling flow penetration depth (cooling depth coefficient), and aerodynamic losses (pressure drop and drag coefficient). A series of simulations were conducted, varying lattice wall thickness, structure period, and Reynolds number, followed by the development of regression models to identify key trends. Experimental verification was carried out using 3D printed samples tested on a specially assembled aerodynamic test rig. Results confirmed the existence of an optimal lattice density, providing a favorable balance between heat transfer and pressure losses. The study highlights the high potential of gyroid TPMS structures for turbine blade cooling systems, where additive manufacturing enables complex internal geometries unattainable by traditional methods. The research demonstrates the practical feasibility and thermo-hydraulic advantages of lattice-based cooling channels and provides accurate predictive models for further optimization of turbine blade designs under high-temperature turbomachinery conditions. Full article

This study investigates the capillary performance and wetting behavior of SLA (Stereolithography) 3D-printed porous structures, focusing on TPMS (triply periodic minimal surfaces)-Gyroid, Octet, Diamond, and Isotruss lattice designs. High-speed imaging was used to analyze droplet interactions, including penetration, spreading, and contact angles, with 16 μL water droplets dropping from 30 mm at 0.77 m/s. Results showed variable contact angles, with Isotruss and Octet having higher angles, while Diamond faced measurement challenges due to surface roughness. Numerical simulations of TPMS-Gyroid of 2 mm³ unit cells validated the experimental results, and Diamond, Octet, and Isotruss structures were simulated. Capillary performance was assessed through deionized (DI) water weight–time (w-t) measurements, identifying that the TPMS-Gyroid structure performed adequately. Structures with 4 mm³ unit cells had low capillary performance, excluding them from permeability testing, whereas smaller 2 mm³ structures demonstrated capillary effects but had printability and cleaning issues. Permeability results indicated that Octet performed best, followed by Isotruss, Diamond, and TPMS-Gyroid. Findings emphasize unit cell size, beam thickness, and droplet positioning as key factors in optimizing fluid dynamics for cooling, filtration, and fluid management. Full article

Selective laser melting (SLM) allows the production of complex lattice structures with tunable mechanical properties. This study proposes an integrated approach to enhance the mechanical properties of Inconel 718 (IN718) lightweight structures by applying distinct heat treatment protocols and tailoring key printing parameters. Four lattice geometries—body-centered cube (BCC), diamond, inverse woodpile (IWP), and gyroid—were selected for evaluation. Three heat treatment protocols were applied to assess their effect on mechanical behavior. Additionally, the influence of key SLM parameters such as laser power, scan speed, hatch spacing, and layer thickness on structural performance was investigated. By combining process tailoring and post-processing strategies, this work demonstrates a method to improve the mechanical response of complex IN718 lattices. The results highlight significant improvements in yield strength and energy absorption for high-performance applications in aerospace and automotive engineering. Full article

This study explores the mechanical performance of triply periodic minimal surface (TPMS) and stochastic lattice structures subjected to low-velocity impact. Two structurally promising geometries—one TPMS-based and one stochastic—were tested and compared with the well-established gyroid. Specimens were fabricated using stereolithography (SLA) and subjected to impact energies of 30 J and 40 J to assess the structural response and energy absorption capabilities. Experimental results show that the proposed TPMS structure exhibits higher impact forces compared with the gyroid, which are associated with significant impactor displacement and deep indentation. These samples demonstrated extensive damage, with cracking propagating through the entire core at higher energies, highlighting their susceptibility to structural failure despite their high initial strength. On the contrary, the stochastic structures allowed localized deformation in the impacted region, thus successfully avoiding catastrophic failure. The impact force efficiency was higher for both gyroid and stochastic geometries, with values ranging between 0.6 and 0.7, indicating effective energy absorption with reduced internal stress gradients. Furthermore, the evaluation of damping performance showed that most structures displayed high damping, as minimal energy was transferred back to the impactor. This work highlights the feasibility and functional versatility of TPMS and stochastic geometries for use in impact mitigation, vibration control, and related engineering applications. Full article

Critical-sized bone defects or CSDs result from bone loss due to trauma, tumor removal, congenital defects, or degenerative diseases. Though autologous bone transplantation is the current gold standard in treating CSDs, its limitations include donor-site morbidity, unavailability of donor bone tissues, risk of infection, and mismatch between the bone geometry and the defect site. Customized scaffolds fabricated using 3D printing and biocompatible materials can provide mechanical integrity and facilitate osseointegration. Ti-6Al-4V (Ti64) is one of the most widely used commercial alloys in orthopedics. To avoid elastic modulus mismatch between bones and Ti64, it is imperative to use porous lattice structures. Ti64 scaffolds with diamond, cubic, and triply periodic minimal surface (TPMS) gyroid lattice architectures were fabricated using selective laser melting (SLM)with pore sizes ranging from 300 to 900 μm using selective laser melting and evaluated for mechanical and biological performance. Increasing pore size led to higher porosity (up to 90.54%) and reduced mechanical properties. Young’s modulus ranged from 13.18 GPa to 1.01 GPa, while yield stress decreased from 478.16 MPa to 14.86 MPa. Diamond and cubic scaffolds with 300–600 μm pores exhibited stiffness within the cortical bone range, while the 900 μm diamond scaffold approached trabecular stiffness. Gyroid scaffolds (600–900 μm) also showed modulus and yield strength within the cortical bone range but were not suitable for trabecular applications due to their higher stiffness. Cytocompatibility was confirmed through leachate analysis and DAPI-stained osteoblast nuclei. The biological evaluation reported maximum cell adherence in lower pore sizes, with gyroid scaffolds showing a statistically significant (p < 0.01) increase in cell proliferation. These findings suggest that 300–600 μm lattice scaffolds offer an optimal balance between mechanical integrity and biological response for load-bearing bone repair. Full article

The design of scaffolds and prostheses benefits from the opportunities provided by additive manufacturing technologies. Specifically, scaffold design using cellular structures based on lattices has become a significant focus. These lattice-based scaffolds exhibit intricate and complex shapes with controlled macro-porosity. In this study, a method is presented that enables the modeling of a graded-density lattice structure for material extrusion additive manufacturing, without relying on a geometric lattice model. The methodology utilizes computed tomography (CT) scans as inputs to obtaining a 3D scalar field and a surface model. The lattice structure is designed and generated within the computer-aided manufacturing (CAM) software, ensuring consistent machine toolpaths. The 3D scalar field, representing a relative density map derived from CT Hounsfield units, drives the variation of the extrusion parameters generated by the CAM, achieving a graded-density lattice. To demonstrate the effectiveness of the method, a section of a human femur bone with a lattice with a triply periodic minimal surface (TPMS) gyroid pattern was designed and 3D-printed, replicating the relative density of the target tissue. Full article

Cellular structures, formed by periodic two- or three-dimensional cells, offer weight reduction without compromising mechanical performance and are commonly fabricated via additive manufacturing. This study investigates the compressive behaviour of three polymer lattice structures—gyroid, diamond, and octet truss—fabricated by fused filament fabrication (FFF). A Box–Behnken experimental design was used to systematically evaluate the influence of three key parameters: cell size, strut/wall thickness, and layer thickness. A total of 225 samples were produced using PLA and subjected to compression testing in accordance with ASTM D1621. Linear regression and response surface methodology were employed to determine the statistical significance and impact of each factor. The results indicate that cell size has the strongest influence on both maximum force and displacement, followed by strut/wall thickness and layer thickness. Among the configurations, gyroid structures had the highest strength-to-density ratio, while diamond structures had the highest deformation capacity. These findings provide design insights for optimising lattice structures in lightweight applications and highlight the importance of carefully balancing geometric and printing parameters in FFF-based polymer components. Full article

This paper proposes two compact, efficient, and lightweight heat exchangers based on triply periodic minimal surfaces (TPMSs). Designed in an annular configuration, the heat exchangers meet the requirements of micro gas turbines for compactness. Two prototypes of Diamond and Gyroid modular TPMS heat exchangers were fabricated using selective laser melting (SLM) with stainless steel. The flow and heat transfer experimental results indicate that, within a Reynolds number range of 200 to 800, the effectiveness of both heat exchangers remained above 0.62, and the average Nusselt numbers of the Diamond and Gyroid structures reached 3.60 and 4.06 times that of the printed circuit heat exchanger (PCHE), respectively. Although both heat exchangers exhibited relatively high friction factors, their overall performance surpassed that of conventional heat exchangers. Additionally, performance comparisons with existing TPMS heat exchangers revealed that smaller lattice sizes contribute to improved volume-based power density, although they result in increased pressure loss. Simulation results indicated that the “merge–split” effect present in both structures enhances heat transfer between the fluid and the wall. Furthermore, the complex channels of the TPMS structures ensure that the fluid maintains strong turbulence intensity throughout the heat exchanger. This study demonstrates that stainless steel TPMS structures can serve as excellent candidates for applications in micro gas turbines. Full article

Freshwater scarcity demands innovative solutions, and Atmospheric Water Generation (AWG) technology offers a promising approach. This study applies a data-driven optimization methodology to enhance AWG efficiency by improving condensation surface design using Triply Periodic Minimal Surface (TPMS) structures. Five TPMS types (Gyroid, Diamond, Lidinoid, SplitP, and Schwartz) were evaluated using thermal simulations in nTop, and a regression-based predictive model was developed to assess the impact of lattice thickness and cell size on surface area to volume ratio (SA/V_S) and temperature difference (ΔT). A multi-objective optimization approach, incorporating sensitivity-weighted desirability analysis, identified optimal design parameters under varying performance priorities. Results show Schwartz exhibits the highest tunability, with both factors significantly influencing its performance, while other TPMS types are primarily governed by lattice thickness. By integrating regression modeling, multi-objective optimization, and sensitivity analysis, this study provides a systematic framework for AWG surface design, offering scalable insights for thermal management and moisture collection efficiency in sustainable water harvesting applications. Full article

The development of prosthetic limbs has benefited individuals who suffered amputations due to accidents or medical conditions. During the development of conventional prosthetics, several challenges have been observed regarding the functional limitations, the restricted degrees of freedom compared to an actual human limb, and the biocompatibility issues between the surface of the prosthetic limb and the human tissue or skin. These issues could result in mobility impairments due to failed mimicry of the actual stress distribution, causing discomfort, chronic pain, and tissue damage or possible infections. Especially in cases where underlying conditions exist, such as diabetes, possible trauma, or vascular disease, a failed adaptation of the prosthetic limb could lead to complete abandonment of the prosthetic part. To address these challenges, the insertion of topologically optimized parts with a biomimetic approach has allowed the optimization of the mimicry of the complex functionality behavior of the natural body parts, allowing the development of lightweight efficient anthropomorphic structures. This approach results in unified stress distribution, minimizing the practical limitations while also adding an aesthetic that aids in reducing any possible symptoms related to social anxiety and impaired social functioning. In this paper, the development of a novel anthropomorphic designed prosthetic foot with a novel Thermoplastic Polyurethane-based composite (TPU-Ground Tire Rubber 10 wt.%) was studied. The final designs contain advanced sustainable polymeric materials, gyroid lattice geometries, and Finite Element Analysis (FEA) for performance optimization. Initially, a static evaluation was conducted to replicate the phenomena at the standing process of a conventional replicated above-knee prosthetic. Furthermore, dynamic testing was conducted to assess the mechanical responses to high-intensity exercises (e.g., sprinting, jumping). The evaluation of the dynamic mechanical response of the prosthetic limb was compared to actual plantogram-derived foot pressure data during static phases (standing, light walking) and dynamic phenomena (sprinting, jumping) to address the optimal geometry and density, ensuring maximum compatibility. This innovative approach allows the development of tailored prosthetic limbs with optimal replication of the human motion patterns, resulting in improved patient outcomes and higher success rates. The proposed design presented hysteretic damping factor and energy absorption efficiency adequate for load handling of intense exercises (0.18 loss factor, 57% energy absorption efficiency) meaning that it is suitable for further research and possible upcycling. Full article

We aimed to evaluate the effects of unit cell design and the volume fraction of 3D-printed lattice structures with relative densities of 30% or 45% on compressive response and orthopedics screw pullout strength. All 3D lattice models were created using FLatt Pack software (version 3.31.0.0). The unit cell size of sheet-based triply periodic minimal surfaces (TPMSs)—Gyroid and Schwarz Diamond—was 5.08 mm, whereas that of skeletal TPMS—Skeletal Gyroid, Skeletal Schwarz Diamond, and Skeletal Schoen I-Wrapped Package—was scaled down to 3.175 and 2.54 mm. Two photopolymer resin types—Rigid 10k and Standard Grey—were used. In uniaxial compression tests, Rigid 10k resin lattices failed at relatively lower strains (<0.11), while Standard Grey lattices endured higher strains (>0.60) and experienced less softening effects, resulting in stress–strain curve plateauing followed by lattice densification. ANOVA revealed significant effects of design and volume fraction at p < 0.001 on compressive modulus, screw pullout strength, and screw withdrawal stiffness of the 3D-printed lattice. The pullout load from 3D-printed lattices (61.00–2839.42 N) was higher than that from open-cell polyurethane foam (<50 N) and lower than that of human bone of similar volume fraction (1134–2293 N). These findings demonstrate that 3D-printed lattices can be tailored to approximate different bone densities, enabling more realistic orthopedic and dental training models. Full article

Lattice structures offer unique mechanical properties and versatility in engineering applications, yet existing designs often struggle to balance performance and material efficiency. This study introduces the brachistochrone curve as a novel framework for optimizing lattice geometries, enhancing mechanical behavior while minimizing material usage. Using finite element simulations and compressive testing of 3D-printed samples, we analyzed the mechanical response of brachistochrone-based (B-) and standard lattice structures (diamond, IWP, gyroid, and BCC). We investigated the scaling behavior of the volume-to-surface area ratio, incorporated fractal dimension analysis, and compared experimental and numerical results to evaluate the performance of B-lattices versus standard designs (S-). Our findings indicate that brachistochrone-inspired lattices enhance mechanical efficiency, enabling the design of lightweight, high-strength components with sustainable material use. Experimental results suggest that B-gyroid lattices exhibit lower stiffness than S-gyroid lattices under small displacements, highlighting their potential for energy absorption applications. Full article