Search Results (27)

Curing plays a fundamental role in determining the mechanical performance, durability, and sustainability of concrete structures. Traditional curing practices, such as water and air curing, are widely used but often limited by long durations, high water demand, and reduced effectiveness under extreme climatic conditions. In response, advanced curing methods such as steam, microwave, electric, autoclave, and accelerated carbonation have been developed to accelerate hydration, refine pore structures, and enhance durability. This review critically examines the performance of both conventional and advanced curing strategies across a range of concrete systems. Findings show that microwave curing achieves up to 85–95% of 28-day wet-cured strength within 24 h, whilst autoclave curing enhances early strength by 40–60%. Electric curing reduces energy demand by approximately 40% compared to steam curing, and carbonation curing lowers carbon dioxide emissions by 30–50% through carbon sequestration. While steam and autoclave curing provide rapid early strength, they may compromise long-term durability through microcracking and increased porosity. No single method was identified as universally optimal; the effectiveness depends on the mix design, application, and environmental conditions. The review highlights future opportunities in smart curing systems, integrating Internet of Things (IoT), sensor technologies, and AI-driven predictive control to enable real-time optimisation of curing conditions. Such innovations represent a critical pathway for improving concrete performance while addressing sustainability targets in the building and construction industry. Full article

Microwave curing has proven to be a highly effective method for enhancing the structural integrity, compressive strength, and heavy metal immobilization performance of geopolymer (GP) gels. For fly ash-based GP gels, optimal compressive strength (126.84 MPa) and minimal heavy metal ion leaching (0.01 mg/L) were achieved under microwave irradiation at 100 W for 75 s. Similarly, metakaolin-based GP gels reached peak compressive strength (76.84 MPa) and reduced heavy metal leaching (0.44 mg/L) under 440 W irradiation for 60 s. Microwave energy significantly accelerates geopolymerization by promoting the aggregation of dispersed particles, rapidly forming a dense, block-like matrix. This accelerated densification enhances the mechanical properties of GP gels within minutes. Moreover, the dense matrix structure effectively encapsulates heavy metal ions, minimizing their leaching through a combination of physical encapsulation and chemical bonding. In summary, microwave treatment significantly enhances both mechanical performance and heavy metal immobilization, offering a practical pathway for sustainable applications. Full article

To elucidate the mechanisms of microstructural changes in ultra-high-performance concrete (UHPC) under microwave exposure, this study characterizes the microstructure at multiple scales using a combination of microscopic experiments and molecular dynamics simulations. The hydration products, pore structure, morphology, and interface transition zone (ITZ) of UHPC specimens were analyzed using mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and scanning electron microscopy (SEM). Molecular dynamics simulations were employed to investigate the uniaxial tensile behavior, free volume, and radial distribution of calcium silicate hydrate (C-S-H) gel, the primary hydration product. The results indicate that microwave curing significantly reduces the pore volume of specimens, with a daily average reduction of 0.15% in the early stages. This accelerated reduction in porosity effectively diminishes the number of high-risk pores. The hydration products formed under microwave curing exhibit higher density and enhanced internal pore optimization. Simulation findings suggest that the non-thermal effects of microwaves play a more significant role in the structural evolution. The molecular orientation of C-S-H changes after oscillation, leading to more ordered molecular arrangements. Mechanical oscillation also expels free volume from the crystal cells, promoting a more compact overall structure and increasing the tensile strength by up to 1 GPa. Full article

Adapting to extremely harsh service environments is an unavoidable challenge for microwave absorption materials. In this paper, C/PyC/SiC composites were prepared by a vacuum impregnation, curing and cracking process with various preparation cycles, and the stress–strain curves were further discussed. The results show that after three cycles, the C/PyC/SiC composite showed significantly enhanced mechanical properties of 83.59 MPa at around 35.00% strain, and it also possessed the best overall electromagnetic microwave absorption performance, with a minimum reflection loss value of −46.04 dB at 16.06 GHz and 1.90 mm of thickness. All in all, we have introduced an innovative method for fabricating electromagnetic microwave-absorbing materials capable of withstanding harsh environmental conditions. Full article

A rapid microwave-assisted process minimizing waste was set up to produce bio-based benzoxazine-like monomers produced from vanillylamine and melamine. Without excessive purification, different viscous liquid precursors had a remarkable ability to form four strong and transparent different solid cross-linked thermosets, displaying lower curing temperatures under 130 °C. The long and strong adhesive performance of the cured materials was observed using glass slides or aluminum surfaces and they could become a good alternative to adhesive epoxy resin for metal surfaces. At the higher temperatures, these solids could act as efficient flame-retardants proven by thermogravimetric measurements. The best candidates gave a limiting oxidation index value of 41.9. In order to improve the intrinsic surface hydrophobicity of the phenolic resins, slight amounts of silica and iron oxide nanoparticles were dispersed in the polymer matrix, and finally mechanical resistance was pointed out. The most promising of our melamine-based resin was loaded with aluminum pigment to furnish a silver-colored paste ready for being cured to afford a robust solid, which does not undergo contraction or deformation. Full article

Ceramic armor protection with complex shapes is limited by the difficult molding or machining processing, and 3D printing technology provides a feasible method for complex-shaped ceramics. In this study, ZrO₂ ceramics were manufactured by 3D printing accompanied with microwave sintering. In 3D printing, the formula of photosensitive resin was optimized by controlling the content of polyurethane acrylic (PUA) as oligomer, and the photosensitive resin with 50% PUA showed excellent curing performance with a small volume shrinkage of 4.05%, media viscosity of 550 mPa·s, and low critical exposure of 20 mJ/cm². Compared to conventional sintering, microwave sintering was beneficial to dense microstructures with fine grain size, and microwave sintering at 1500 °C was confirmed as an optimized sintering process for the 3D-printed ZrO₂ ceramics, and the obtained ceramics showed a relative density of 98.2% and mean grain size of 2.1 μm. The PUA content further affected the microstructure and mechanical property of the ZrO₂ ceramics. The sample with 10%~40% PUA showed some pores due to the low viscosity and large volume shrinkage of photosensitive resins, and the sample with 60% PUA exhibited an inhomogeneous microstructure with agglomeration, attributed to the high viscosity of photosensitive resins. Finally, the ZrO₂ ceramics via 3D printing with 50% PUA showed superior mechanical properties, whose Vickers hardness was 3.4 GPa, fracture toughness was 7.4 MPa·m^1/2, flexure strength was 1038 MPa, and dynamic strength at 1200 s⁻¹ was 4.9 GPa, conducive to the material’s employment as armor protection ceramics. Full article

Microwave technology in geopolymer synthesis offers a transformative, sustainable alternative to traditional methods, enhancing material properties and production efficiency. However, the effects of microwave-induced changes on pore structure and their relationship with mechanical strength and environmental performance, such as heavy metal leachability, are not fully understood. This study investigates the impact of microwave pre-curing on geopolymers, focusing on how microwave power and duration influence their pore structure and environmental performance. A total of 48 mixtures were prepared using sodium silicate and sodium hydroxide as alkali activators, with metakaolin and fly ash as raw materials. The modulus was adjusted to 1.5, and the liquid-to-solid ratio was set at 1.6 for metakaolin and 0.7 for fly ash. Microwave irradiation power settings of 100 W, 300 W, 440 W, 600 W, and 800 W were tested. The heating times ranged from 30 s to 90 s at intervals of 15 s. Our findings reveal that optimal microwave settings (100 watts for 45 s) can significantly enhance mechanical properties, with compressive strengths reaching 15.9 MPa for fly ash-based and 9.094 MPa for metakaolin-based geopolymers. However, excessive microwave energy leads to increased porosity, with adverse effects on structural integrity. Moreover, microwave pre-curing effectively reduces heavy metal leachability. Chromium (III) was used in leaching tests and it was demonstrated that ion concentrations as low as 0.097 mg/L enhance environmental safety. Advanced techniques like Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD) and X-ray CT were applied for the analysis of the atomic bonding, phases and pore structure of the studied geopolymers along with their ability to withstand compression (MPa). Chromium (III) was encapsulated and its leached concentration was measured by ICP-MS to evaluate the performance of the synthesized geopolymers. These results underscore the need for precise control over microwave irradiation parameters to maximize the benefits while mitigating negative impacts. This study provides valuable insights into the controlled use of microwave technology for geopolymer synthesis, recommending optimal irradiation conditions for improved performance and sustainability and advancing sustainable construction materials. The developed geopolymers show promise for applications in construction, waste stabilization, and heavy metal immobilization, contributing to more sustainable and environmentally friendly materials in these industries. Full article

Efflorescence, a time-dependent and water-driven phenomenon, is a major concern in alkali-activated materials (AAMs), impacting their practical use and preservation in a time-frozen state for post-characterisation. Although a method for stopping chemical reactions in conventional cements exists, it is time-consuming and not chemical-free. Therefore, this study explored the effects of low-power microwave-induced dehydration on efflorescence, mechanical performance, and structural integrity in AAMs, to create an alternative and more “user-friendly” dehydration method. For this purpose, several mixtures based on secondary raw (slag, fly ash, glass wool, and rock wool) and non-waste (metakaolin) materials were activated with a commercial Na-silicate solution in ratios that promoted or prevented efflorescence. Characterisation techniques, including Fourier-transform infrared spectroscopy and X-ray diffraction, showed that microwave dehydration effectively removed water without altering crystallinity, while mercury intrusion porosimetry and compressive strength tests confirmed increased porosity. In addition to being an efficient, time-saving, and solvent-free manner of stopping the reactions in AAMs, microwave irradiation emerged as an innovative, chemical-free method for evaluating curing finalisation and engineering foams in a stage when all other existing methods fail. However, the artificially provoked efflorescence in aged dehydrated AAMs connected the slipperiness of AAM with the instant extraction of Na, which raised the need for further research into alternative alkali replacements to evaluate the practical use of AAM. Full article

The application of microwave heating technology can significantly enhance the water evaporation rate of emulsified asphalt mixtures post paving. To improve the microwave absorption and curing performance of these mixtures, SiC-Fe₃O₄ composite material (SF) was incorporated. This addition aims to enhance the microwave absorption efficiency and accelerate the curing process of emulsified asphalt mixtures under microwave heating. This study begins with an analysis of the microwave absorption principles pertinent to emulsified asphalt mixtures. Subsequently, the microwave heating temperature fields of ordinary emulsified asphalt mixture (EAM), SiC emulsified asphalt mixture (S-EAM), Fe₃O₄ emulsified asphalt mixture (F-EAM), and SiC-Fe₃O₄ emulsified asphalt mixture (SF-EAM) were simulated using COMSOL Multiphysics finite element software (COMSOL 6.2). The early strength variations in SF-EAM under different microwave heating durations were then examined through adhesion tests, leading to the proposal of a microwave heat curing process for SF-EAM. Finally, the wear resistance, water damage resistance, rutting resistance, and skid resistance of SF-EAM post-microwave curing were evaluated through wet wheel wear tests, wheel track deformation tests, and road friction coefficient tests. The results indicate that the optimal microwave heating time is 90 s, with the microwave absorption performance of the materials ranked as follows: EAM, S-EAM, F-EAM, and SF-EAM, from lowest to highest. The road performance of SF-EAM complies with specification requirements, and its wear resistance, water damage resistance, and rutting resistance are notably improved after microwave heating. Full article

The vibration pretreatment–microwave curing process can achieve high-quality molding under low-pressure conditions and is widely used in the curing of resin-based composites. This study investigated the effects of the vibration pretreatment process parameters on the void content and the fiber weight fraction of T700/TRE231; specifically, their influence on the interlaminar shear strength and impact strength of the composite. Initially, an orthogonal experimental design was employed with interlaminar shear strength as the optimization target, where vibration acceleration was determined as the primary factor and dwell time as the secondary factor. Concurrently, thermogravimetric analysis (TGA) was performed based on process parameters that corresponded to the extremum of interlaminar shear strength, revealing a 2.17% difference in fiber weight fraction among specimens with varying parameters, indicating a minimal effect of fiber weight fraction on mechanical properties. Optical digital microscope (ODM) analysis identified interlaminar large-size voids in specimens treated with vibration energy of 5 g and 15 g, while specimens subjected to a vibration energy of 10 g exhibited numerous small-sized voids within layers, suggesting that vibration acceleration influences void escape pathways. Finally, impact testing revealed the effect of the vibration pretreatment process parameters on the impact strength, implying a positive correlation between interlaminar shear strength and impact strength. Full article

Objective: This study investigates the influence of high-temperature treatment on the deformation properties and structural deformation of recycled aggregate concrete (RAC) in response to potential fire hazards in the construction industry. Methods: Standard-cured 28-day RAC specimens were subjected to microwave heating at 300 °C and 600 °C, with subsequent uniaxial compression tests utilizing a WDW-2000 machine and a VIC 3D strain measurement system to analyze strain data through digital image correlation (DIC) technology. Results: After treatment at 300 °C, recycled aggregate concrete (RAC) demonstrated superior mechanical properties to fresh concrete aggregates. This enhancement may be attributed to the more robust siloxane bonds (Si-O-Si) in the recycled materials. Conversely, exposure to 600 °C intensified internal structural damage, notably lowering the material’s elastic modulus and peak stress. DIC analysis highlighted the correlation among temperature, volumetric strain, and crack development patterns, with more extensive cracking at 600 °C. Conclusions: Moderate-temperature treatment enhances RAC’s structure and deformation properties, while high-temperature treatment diminishes its performance. These findings provide valuable insights for assessing building safety post-fire and the application of RAC, emphasizing its suitability at moderate temperatures and risks at high temperatures. Full article

To address the challenges of slow curing speed and suboptimal microwave absorption during the paving of cold-mixed and cold-laid asphalt mixtures, this study introduces SiC-Fe₃O₄ composite material (SF) into emulsified asphalt mixtures to enhance microwave absorption and accelerate curing via microwave heating. Initially, based on the maximum density curve theory, an appropriate mineral aggregate gradation was designed, and the optimal ratio of emulsified asphalt mixture was determined through mixing tests, cohesion tests, wet wheel wear tests, and load wheel sand adhesion tests. Subsequently, the influence of SF content on the mixing performance of emulsified asphalt mixtures was analyzed through mixing and consistency tests. Finally, the microwave absorption performance of the mixture was evaluated by designing microwave heating tests under different conditions, using temperature indicators and quality indicators. The experimental results indicate that when SF content ranges from 0% to 4%, the mixing performance of the emulsified asphalt mixture meets specification requirements. The dosage of SF, SF composite ratio, and microwave power significantly impact microwave absorption performance, whereas environmental temperature has a relatively minor effect. The optimal mix ratio for the emulsified asphalt mixture is mineral aggregate:modified emulsified asphalt:water:cement = 100:12.8:6:1. The ideal SF dosage is 4%, with an optimal SiC to Fe₃O₄ composite ratio of 1:1, and a suitable microwave power range of 600–1000 W. Full article

The size of current microwave-driven UV lamps limits their direct application in dental light curing. This article proposes a coaxial structure to miniaturize the UV lamp. First, the Drude model and the finite difference time domain algorithm were used to analyze the multi-physical field coupling and the complex field distribution within the lamp. Second, the dimensional parameters of the lamp were optimized, which enabled the lamp to be miniaturized and operate with high performance. Third, to analyze the sensitivity of the lamp, the effects of input power, gas pressure, and gas composition on its performance were investigated. It was found that an input power of 6 watts was enough to light the bulb with over 90% energy utilization. Finally, to verify the feasibility, an experimental system was set up. The lamp was successfully lit in the experiment, and its spectral output was tested. The results show that the microwave-driven UV lamp based on a coaxial structure is miniaturized and broad-spectrum, making it suitable for clinical dental light curing. Full article

Intrahepatic cholangiocarcinoma (ICC) has a poor prognosis, and surgical resection (SR) offers the only potential for cure. Unfortunately, only a small proportion of patients are eligible for resection due to locally advanced or metastatic disease. Locoregional therapies (LRT) are often used in unresectable liver-only or liver-dominant ICC. This review explores the role of these therapies in the treatment of ICC, including radiofrequency ablation (RFA), microwave ablation (MWA), transarterial chemoembolization (TACE), transarterial radioembolization (TARE), external beam radiotherapy (EBRT), stereotactic body radiotherapy (SBRT), hepatic arterial infusion (HAI) of chemotherapy, irreversible electroporation (IE), and brachytherapy. A search of the current literature was performed to examine types of LRT currently used in the treatment of ICC. We examined patient selection, technique, and outcomes of each type. Overall, LRTs are well-tolerated in the treatment of ICC and are effective in improving overall survival (OS) in this patient population. Further studies are needed to reduce bias from heterogenous patient populations and small sample sizes, as well as to determine whether certain LRTs are superior to others and to examine optimal treatment selection. Full article

BaFe₁₂O₁₉-polypyrrolenanocomposites were prepared via the in situ chemical oxidative polymerization of pyrrole monomers in the presence of BaFe₁₂O₁₉ powder, with ammonium persulfate as an oxidant and sodium dodecyl benzene sulfonate as a dopant. X-ray diffraction measurements and Fourier-transform infrared spectroscopy indicated that there were no chemical interactions between BaFe₁₂O₁₉ and polypyrrole. In addition, scanning electron microscopy showed that the composites exhibited a core–shell structure. Subsequently, the prepared nanocomposite was used as a filler to prepare a coating suitable for ultraviolet curing. The performance of the coating was investigated by evaluating its hardness, adhesion, absorbance, and resistance to acids and alkalis. Importantly, the addition of BaFe₁₂O₁₉-polypyrrole nanocomposites not only improved the coating hardness and adhesion but also produced a coating with a good microwave absorption performance. The results suggested that BaFe₁₂O₁₉/PPy composite has a lower reflection loss peak and a larger effective bandwidth at the X band when the proportion of the absorbent sample is 5–7%, when the absorption performance is the best. The reflection loss is in the range of 8.88–10.92 GHz below −10 dB. Full article