Search Results (51)

Soft organic gels are commonly used as tissue phantoms for experiments. In the mimic ultrasound imaging field, researchers are developing approaches to modify the acoustic properties of the gels. Introducing oil liquids and hard solid particles are two common methods to tune acoustic and mechanical properties of the soft gels. In this work, the acoustic wave energy loss mechanisms were studied in detail on Agar gel with both micro-Graphite and nano-Alumina particles. Via experimental measurements, the results show that the effective acoustic energy loss is comparable in these two recipes. However, temporal pulse elongation and scattering behaviors were distinguishable. To understand the sound attenuation mechanism in detail, numerical simulations in controlled conditions were conducted, from wavelengths longer than the particle diameter to wavelengths shorter than particles, and we compared perfect bonding and insufficient bonding between the hard particles surrounding gels. Comparing the experimental observations and numerical simulation results, the Agar gel with nano-Alumina presents stronger dispersion-induced energy loss than the Agar gel with micro-Graphite. On the contrary, the Agar gel with micro-Graphite shows more significant scattering-induced destructive interferences than the Agar gel with nano-Alumina. Full article

High-density polyethylene (HDPE) is a widely used polymer known for its excellent mechanical properties and chemical resistance. This study investigated the impact of incorporating varying percentages of nano-graphene particles (NGP) into HDPE on its thermal, mechanical, and tensile properties. Differential scanning calorimetry (DSC) analysis revealed that the addition of NGP enhanced the thermal stability and crystallization behavior of HDPE, with optimal performance observed at a 5% NGP concentration. Mechanical property evaluations indicated that small additions of NGP initially reduced zero-shear viscosity from 114,667 Pa·s to 44,045 Pa·s at 1% NGP, but higher concentrations improved the material’s rigidity and strength, with the best results at 3% NGP, where the flexural modulus reached 980 MPa. Tensile tests showed that while small amounts of NGP may decrease tensile strength from 26.4 MPa to 23.5 MPa at 1% NGP, higher concentrations significantly enhanced these properties, with tensile strength at break reaching 27 MPa and tensile elongation peaking at 20.8% at 7% NGP. The findings highlight the potential of NGP to enhance the performance of HDPE composites, making them suitable for a wide range of industrial applications. These enhanced composites are particularly important for the bottling industry, where improved material properties can lead to lighter, stronger, and more efficient packaging solutions. Full article

This study presents a novel Basalt-based grafted graphitic carbon nitride composite (Basalt–MTES/g-C₃N₄) for the efficient pretreatment of Cr(VI) in ethylene wastewater. The composite was synthesized by the acid purification of natural Basalt, surface modification with hydroxymethyl triethoxysilane (MTES), and the subsequent grafting of g-C₃N₄. Characterization confirmed the uniform distribution of nano-sized g-C₃N₄ particles on a Basalt surface with intact chemical bonding, where 82.63% of melamine participated in g-C₃N₄ crystallization. The material exhibited a high specific surface area (403.55 m²/g) and mesoporous structure (34.29 nm). Acidic conditions promoted the protonation of amino groups in g-C₃N₄, significantly enhancing Cr(VI) adsorption via ion exchange. Adsorption kinetics followed the pseudo-second-order model, while isotherm data fitted the Langmuir monolayer adsorption mechanism. The composite achieved 97% Cr(VI) recovery through chromatographic extraction and retained 96.87% removal efficiency after five regeneration cycles. This work demonstrates a cost-effective, recyclable green pretreatment material for high-sensitivity Cr(VI) monitoring in ethylene industry wastewater, offering dual benefits in environmental remediation and regulatory compliance. The design synergizes natural Basalt’s stability with g-C₃N₄’s adsorption affinity, showing practical potential for sustainable wastewater treatment technologies. Full article

Multifunctional reinforced polymer composites provide an ideal platform for next-generation smart materials applications, enhancing matrix properties like electrical and thermal conductivity. Reinforcements are usually based on functional metal alloys, inorganic compounds, polymers, and carbon nanomaterials. The latter have drawn significant interest in developing high-performance smart composites due to their exceptional mechanical, electrical, and thermal properties. The increasing demand for highly complex functional structures has led additive manufacturing to become a reference technology for the production of smart material components. In this study, laser sintering technology was adopted to manufacture nano-graphite/nylon-12 composites with a carbon-based particle reinforcement content of up to 10% in weight. The results showed that the addition of the filler led to the fabrication of samples that reached an electrical conductivity of around 4·10⁻⁴ S/cm, in contrast to the insulating behavior of a bare polymeric matrix (i.e., lower than 10⁻¹⁰ S/cm), while maintaining a low production cost, though at the expense of mechanical performance under both tensile and bending loads. Full article

Waste nanomaterials pose environmental and human health concerns and they need to be urgently and efficiently managed. In this study, a fungal biotemplate was used to accumulate and recover nano-Fe₂O₃ materials from an aqueous solution. Then, recovered nano-Fe₂O₃ materials were activated to form a high-performance magnetic porous carbon composite (FePC) for energy storage and organic pollutant removal. The results indicate that high concentrations (500 mg/L) of 50 nm Fe₂O₃ particles can be completely recovered using a cross-linked Neurospora crassa fungus (NC), primarily because of its encapsulation function. In addition, the surface area, degree of graphitization, and heteroatom content of the FePC materials can be boosted by the catalytic effects of the incorporated Fe atoms. The developed FePC materials exhibit potential as high electrical double-layer capacitors as well as strong retention capabilities, excellent stability, and efficient adsorption of triclosan (TCS, ~526 mg/g). Additionally, these FePC materials exhibit superior capacities for energy storage and pollutant reduction compared to commercial and reported carbon materials. These results reveal a sustainable route for the recovery and reutilization of nanomaterials. Full article

Antimicrobial polymeric coatings rely not only on their surface functionalities but also on nanoparticles (NPs). Antimicrobial coatings gain their properties from the addition of NPs into a polymeric matrix. NPs that have been used include metal-based NPs, metal oxide NPs, carbon-based nanomaterials, and organic NPs. Copper NPs and silver NPs exhibit antibacterial and antifungal properties. So, when present in coatings, they will release metal ions with the combined effect of having bacteriostatic/bactericidal properties, preventing the growth of pathogens on surfaces covered by these nano-enhanced films. In addition, metal oxide NPs such as titanium dioxide NPs (TiO₂ NPs) and zinc oxide NPs (ZnONPs) are used as NPs in antimicrobial polymeric coatings. Under UV irradiation, these NPs show photocatalytic properties that lead to the production of reactive oxygen species (ROS) when exposed to UV radiation. After various forms of nano-carbon materials were successfully developed over the past decade, they and their derivatives from graphite/nanotubes, and composite sheets have been receiving more attention because they share an extremely large surface area, excellent mechanical strength, etc. These NPs not only show the ability to cause oxidative stress but also have the ability to release antimicrobial chemicals under control, resulting in long-lasting antibacterial action. The effectiveness and life spans of the antifouling performance of a variety of polymeric materials have been improved by adding nano-sized particles to those coatings. Full article

Biomass, though a major energy source, remains underutilized. Biochar from biomass pyrolysis, with its high porosity and surface area, is especially useful as catalyst support, enhancing catalytic activity and reducing electron recombination in photocatalysis. Indonesia, the world’s top palm oil producer, generated around 12 million tons of empty fruit bunches (EFBs) in 2023, making EFBs a promising biochar source. This study synthesizes biochar from leftover EFB fibers at 500, 800, and 1000 °C, analyzing structural changes via infrared and Raman spectroscopy, along with particle size and surface area analysis, laying the groundwork for future biochar research. The smallest particle size and highest surface area gained was 71.1 nm and 10.6 × 10² m²/g. Spectroscopic analysis indicates that biochar produced at 1000 °C has produced nano-crystalline graphite with a crystallite size of approximately 5.47 nm. This provides higher defect density, although with lower conductivity. Other studies indicate that our biochar can be used as catalyst support for various green energy-related applications, i.e., counter electrodes, electrocatalysts, and photocatalysts. Full article

High-temperature steam injection is a primary method for viscosity reduction and recovery in heavy oil reservoirs. However, due to the high mobility of steam, channeling often occurs within the reservoir, leading to reduced thermal efficiency and challenges in enhancing oil production. Foam fluids, with their dual advantages of selective plugging and efficient oil displacement, are widely used in steam-injection heavy oil recovery. Nonetheless, conventional foams tend to destabilize under high-temperature conditions, resulting in poor stability and suboptimal plugging performance, which hampers the efficient development of heavy oil resources. To address these technical challenges, this study introduces a foam system reinforced with Janus nano-graphite, a high-temperature stabilizer characterized by its small particle size and thermal resistance. The foaming agents used in the system are sodium α-olefin sulfonate (AOS), an anionic surfactant, and octadecyl hydroxylpropyl sulfobetaine (OHSB), a zwitterionic surfactant. Under conditions of 250 °C and 5 MPa, the foam system achieved a half-life of 47.8 min, 3.4 times longer than conventional foams. Janus nano-graphite forms a multidimensional network structure in the liquid phase, increasing internal friction and enhancing shear viscosity by 1.2 to 1.8 times that of conventional foams. Furthermore, the foam gel system demonstrated effective steam-channeling control in heterogeneous heavy oil reservoirs, particularly in reservoirs with permeability differentials ranging from 3 to 9. These findings suggest that the Janus nano-graphite reinforced foam system holds significant potential for steam-channeling mitigation in heavy oil reservoirs. Full article

The catalytic decomposition of CH₄ to H₂ and carbon nanotubes (CNTs) was investigated regarding Pt(1)-Fe(30)/MCM-41 and Fe(30)/MCM-41 using a fixed-bed flow reactor under an atmosphere. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscope (TEM), and Raman spectroscopy were used to characterize the behavior of Pt(1)-Fe(30)/MCM-41 and Fe(30)/MCM-41. The hydrogen yield of Pt(1)-Fe(30)/MCM-41 was 3.2 times higher than that of Fe(30)/MCM-41. When 1 wt% of Pt was added to Fe(30)/MCM-41(Mobil Composition of Matter No. 41), the atomic percentage of Fe2p increased from 13.39% to 16.14% and the core Fe2p_1/2 electron levels of Fe⁰ and Fe²⁺ chemically shifted to lower energies (0.2 eV and 0.1 eV, respectively) than those of Fe(30)/MCM-41. The Fe, Pt, Si, and O nanoparticles were uniformly distributed on the catalyst surface, and the average iron particle sizes of the Pt(1)-Fe(30)/MCM-41 and Fe(30)/MCM-41 were about 33.4 nm and 58.5 nm, respectively. This is attributed to the uniform distribution of the nano-sized iron particles on the MCM-41 surface, which was due to the suitable metal-carrier interaction (SMCI) between Fe, Pt, and MCM-41 and the high reduction degree of Fe due to the spillover effect of H₂ from Pt to Fe. Pt(1)-Fe(30)/MCM-41 produced multiwalled CNTs and bamboo-shaped CNTs with high crystallinity and graphitization degree using the tip-growth mechanism, with an I_D/I_G ratio of 0.93 and a C(101)/C(002) ratio of 0.64. Full article

Dry lubricants used in highly loaded rolling bearings are in the focus of current research. In previous studies, graphene platelets applied as dry lubricants on the surfaces of angular contact ball bearings demonstrated superior properties. These specific bearings, experiencing both rolling and spinning motion, create more severe conditions for dry lubricants. To gain deeper insights into the lubrication effects, micro-tribological studies were carried out on the respective film formation and running behavior effects. In the tests, a fixed steel ball slid against an oscillating counterpart under a defined load. During the measurements, the applied load and tangential forces on the ball were recorded to calculate the friction. Comparative investigations included nano-graphite particles and fullerene as dry lubricants, in addition to graphene platelets of various staple thicknesses. To increase the adhesion of the films to the surfaces, a pre-rolling process was implemented. Afterwards, the friction on the compressed films was measured. The results indicate that the pre-rolling process effectively reduces the friction of the system. After testing, the surfaces underwent analysis using laser scanning microscopy to assess the formed films, wear, and material transfer. It has been demonstrated that the pre-rolling process leads to the formation of a very thin compacted film with surface protective properties. With the ball as a counterpart, the graphene platelets generate a transfer film on the contacting surface. Full article

(Si/graphite)@C and (Si/graphite/graphene)@C were synthesized by coating asphalt-cracked carbon on the surface of a Si-based precursor by spray drying, followed by heat treatment at 1000 °C under vacuum for 2h. The impact of graphene on the performance of silicon–carbon composite-based anode materials for lithium-ion batteries (LIBs) was investigated. Transmission electron microscopy (TEM) and selected area electron diffraction (SAED) images of (Si/graphite/graphene)@C showed that the nano-Si and graphene particles were dispersed on the surface of graphite, and thermogravimetric analysis (TGA) curves indicated that the content of silicon in the (Si/graphite/graphene)@C was 18.91%. More bituminous cracking carbon formed on the surface of the (Si/graphite/graphene)@C due to the large specific surface area of graphene. (Si/Graphite/Graphene)@C delivered first discharge and charge capacities of 860.4 and 782.1 mAh/g, respectively, initial coulombic efficiency (ICE) of 90.9%, and capacity retention of 74.5% after 200 cycles. The addition of graphene effectively improved the cycling performance of the Si-based anode materials, which can be attributed to the reduction of electrochemical polarization due to the good structural stability and high conductivity of graphene. Full article

Due to its mechanical, rheological, and chemical properties, high-density polyethylene (HDPE) is commonly used as a material for producing the pipes for transport of various media. Low thermal conductivity (0.4 W/mK) narrows down the usage of HDPE in the heat exchanger systems. The main goal of the work is to reduce the vertical depth of the HDPE pipe buried in the borehole by increasing the thermal conductivity of the material. This property can be improved by adding certain additives to the pure HDPE matrix. Composites made of HDPE with metallic and non-metallic additives show increased thermal conductivity several times compared to the thermal conductivity of pure HDPE. Those additives affect the mechanical properties too, by enhancing or degrading them. In this research, the thermal conductivity and tensile properties of composite made of HDPE matrix and two types of additives, expanded graphite (EG) and boron nitride (BN), were tested. Micro-sized particles of EG and two different sizes of BN particles, micro and nano, were used to produce composite. The objective behind utilizing composite materials featuring dual additives is twofold: firstly, to enhance thermal properties, and secondly, to improve mechanical properties when compared with the pure HDPE. As anticipated, the thermal conductivity of the composites exhibited an eightfold rise in comparison to the pure HDPE. The tensile modulus experienced augmentation across all variations of additive ratios within the composites, albeit with a marginal reduction in tensile strength. This implies that the composite retains a value similar to pure HDPE in terms of tensile strength. Apart from the enhancement observed in all the aforementioned properties, the most significant downside of these composites pertains to their strain at yield, which experienced a reduction, declining from the initial 8.5% found in pure HDPE to a range spanning from 6.6% to 1.8%, dependent upon the specific additive ratios and the size of the BN particles. Full article

This paper presents an investigation into the plume characteristics of composite propellants fabricated by polytetrafluoroethylene (PTFE) filled with different carbon additives (nano-carbon powder, graphite, and graphene) under laser irradiation in a vacuum environment. The dynamic plumes generated by the laser ablation of different modified propellant samples were captured using a high-speed camera, and the feature parameters of the plumes were extracted by image processing. The results indicated that doping carbon particles in PTFE enhanced the quality of the plasma plumes. The plume area increased up to a certain value and then stabilized, while end of plume clusters remained for a short time. Further analysis revealed that the propellant sample doped with graphene exhibited the maximum plume length and expansion rate, whereas the propellant sample doped with nano-carbon demonstrated the largest plume area. Moreover, a higher graphene doping ratio promoted greater plume length, expansion speed, and plume area. However, when the doping ratio exceeded 3%, the gain of the plume parameters gradually became saturated, and the optimal doping ratio appeared to be 5%. Full article

To reduce vehicle exhaust gas pollution in transport-intensive roadways and tunnels, six types of photocatalytic asphalt binders were designed using graphite-phase carbon nitride (g-C₃N₄) and nanoscale titanium dioxide (nano-TiO₂) particles. In this paper, the rheological behaviors and fatigue life of the nano-TiO₂-modified asphalt binder (TiO₂-MA) and g-C₃N₄-modified asphalt binder (C₃N₄-MA) were investigated. NO degradation capacity of six types of photocatalytic asphalt binders was characterized under visible light conditions. The results showed that TiO₂-MA had more excellent rheological behaviors and rutting resistance than C₃N₄-MA. In addition, 4 wt% nano-TiO₂ markedly improved the rheological behaviors and rutting resistance of MA compared to other dosages. TiO₂-MA exhibited higher fatigue resistance. The fatigue life of TiO₂-MA with 4 wt% nano-TiO₂ was increased to 234.1% at 2.5% strain and 242.5% at 5% strain, respectively, compared to base asphalt binder (BA). C₃N₄-MA had better NO degradation capacity than TiO₂-MA. Meanwhile, the NO degradation efficiency of C₃N₄-MA reached 17.8% with 5 wt% g-C₃N₄. Full article

Oil spills necessitate the development of effective methods for preventing their damaging effects on the environment. A number of physical, chemical, thermal, and biological methods are used to combat oil spills. Among them, sorption is considered to be efficient in removing thin oil films from water surfaces. Currently, there is an urgent need for simple methods of obtaining oil sorbents that include a magnetosensitive component to optimize the process of removing oil from the water surface. The purpose of the work is to obtain and research oil sorbents resistant to destruction, with increased bulk density and complex magnetosensitivity, based on thermally expanded graphite (TEG) with the inclusion of micro- and nano-particles of iron and its oxides. The structure and composition of the new composite material was characterized using scanning electron microscopy, energy dispersive X-ray analysis, X-ray diffractometry, thermogravimetric analysis, and laser diffraction particle sizing. The composite sorbent comprised TEG with the inclusion of iron-containing magnetosensitive particles. Metal-carbon nanoparticles (MCN) were used as the magnetosensitive component; they had a magnetosensitive iron core covered with a carbon shell. We used two methods of synthesis, namely (i) mechanical mixing of the TEG flakes and MCN particles, and (ii) applying a thermal shock (microwave processing) to the mixture of graphite intercalated with sulphuric acid and micro- and nanoparticles of iron and iron oxides. In the first case, MCN particles were fixed on the faces, edges, and other surface defects of the TEG flakes due to intermolecular forces, coordinate bonds, and electrostatic interaction. The strong adhesion of magnetosensitive iron/iron oxide and TEG particles in the second case was due to the mutual dissolution of iron and carbon components during the thermal shock, which formed an interfacial layer in which iron carbide is present. The presence of magnetosensitive components in the structure of the proposed oil sorbents allows the use of magnetic separation for the localization and removal of oil spills, increases the density of sorbents, and, accordingly, leads to a decrease in windage while retaining the advantageous properties of thermally expanded graphite. According to the results of laboratory studies, the efficiency of removing oil from the water surface is not lower than 95–96%. Full article