Search Results (632)

Photocatalytic decomposition of water to produce hydrogen and the degradation of organic pollutants are among the most ideal strategies for addressing energy shortages and environmental pollution. Moreover, constructing organic–inorganic heterojunctions based on surface interactions is one of the most effective strategies for enhancing photocatalytic activity. In this work, a novel II-type polyimide/zinc sulfide (PI/ZnS) heterojunction photocatalyst was successfully synthesized for the first time through a simple hydrothermal method. The influence of PI in the PI/ZnS composite material was systematically studied. The 1PI/ZnS composite shows the highest rate (587.7 μmol/g/h) of photocatalytic water splitting for hydrogen production, which is approximately 19% higher than the value of ZnS (492.5 μmol/g/h), and it is 34.6 times the PI value (16.95 μmol/g/h). The degradation efficiency of the 3 PI/ZnS composite is nearly 35.5 times that of PI and nearly 1.9 times that of ZnS. The enhancement in the photocatalytic activity of the PI/ZnS photocatalyst is mainly attributed to the dense interface and II-type heterojunction between the PI and ZnS, which effectively improves the spatial separation efficiency of photogenerated carriers. This study demonstrates that the nanostructured II-type heterojunction in the PI/ZnS composite can significantly improve the photocatalytic performance of polyimide photocatalysts. Full article

It is known that when an n-type semiconductor and a p-type semiconductor (i.e., a p–n junction) are connected, an intrinsic electric field is formed due to the diffusion motion of majority carriers. The direction of this intrinsic electric field in the p–n junction runs from the n-type to the p-type semiconductor (n→p). If the migration directions of photogenerated charge carriers in the conduction band (CB) and valence band (VB) of the two contacting semiconductors align with the direction of the intrinsic electric field in the heterojunction, band-to-band transfer occurs. In experiments using TiO₂-based composite photocatalysts, the heterojunction catalyst forms a structure analogous to a p–n junction relative to CdS/TiO₂; however, due to differing carrier concentrations, TiO₂ exhibits a p-type character while CdS shows an n-type character. Under the influence of the intrinsic electric field, photogenerated electrons migrate to the p-type TiO₂ surface, while holes migrate to the n-type CdS surface. The migration directions of photogenerated electrons and holes in the CB and VB of both CdS and TiO₂ match those observed in a typical p–n junction, confirming that the photocarrier migration mechanism in TiO₂-dominated CdS/TiO₂ systems follows a band-to-band transfer mechanism. When CdS serves as the dominant component, rapid recombination occurs between electrons in TiO₂’s CB and holes in CdS’s VB, resulting in significant electron accumulation in TiO₂’s CB and substantial hole generation in CdS’s VB. Electrons in the CB of TiO₂, which carries a higher negative potential, reduce O₂ to •O₂⁻, while holes in the VB of CdS, possessing a higher positive potential, generate •OH⁻, thereby enhancing photocatalytic activity; thus, the photoexcited carrier transfer mechanism follows Scheme Z. Full article

Lignin, one of the most abundant renewable aromatic biopolymers on earth, represents a promising feedstock for producing high-value chemicals capable of replacing fossil-derived resources, yet its structural complexity poses significant barriers to efficient valorization. In recent years, photocatalytic transformation has emerged as an attractive strategy to overcome these limitations, employing heterogeneous catalysts to harness solar energy for the selective cleavage and functionalization of lignin under mild and sustainable conditions. This review provides a comprehensive overview of recent progress in heterogeneous photocatalysts designed for lignin degradation, emphasizing how material composition, morphological features, surface properties, and band-gap engineering influence catalytic efficiency and selectivity. Key reaction pathways and mechanistic insights are discussed to elucidate the roles of photo-generated charge-carriers, reactive oxygen species, and catalyst–lignin interactions in driving depolymerization and upgrading processes. Furthermore, we analyze current challenges—including low reaction selectivity, catalyst deactivation, and limited scalability—and highlight emerging strategies aimed at improving catalyst stability, enhancing visible-light utilization, and promoting targeted product formation. By critically examining these advancements and limitations, this review outlines future opportunities for the development of efficient, robust, and economically viable photocatalytic systems to enable the sustainable and large-scale valorization of lignin. Full article

The selective photocatalytic oxidation of biomass-derived 5-hydroxymethylfurfural (HMF) into high-value 2,5-diformylfuran (DFF) under green conditions is a promising route toward carbon neutrality. However, achieving high efficiency and selectivity in pure water remains challenging due to limited oxygen solubility and nonselective radical reactions. In this study, a series of amorphous MoS₃-modified Zn₃In₂S₆ nanoflowers (x%MS/ZIS) with varying MoS₃ loadings were successfully synthesized via a one-step hydrothermal method and served as the photocatalysts for the highly selective oxidation of HMF to DFF. The incorporation of MoS₃ significantly enhances visible-light absorption, promotes efficient separation of photogenerated carriers, and accelerates surface reaction kinetics. Under visible light irradiation, the optimized 2.4%MS/ZIS catalyst achieves 64.7% HMF conversion and 89.5% DFF selectivity in pure water within 6 h, ~39-fold enhancement in DFF yield compared to pristine Zn₃In₂S₆. Radical scavenging experiments and electron paramagnetic resonance analyses suggest that superoxide radicals (·O₂⁻) and photogenerated holes are the main reactive oxygen species governing the selective oxidation, while the absence of ·OH radicals suppresses overoxidation. This study demonstrates a viable and green strategy for the valorization of biomass platform molecules through visible-light-driven photocatalysis in pure water. Full article

Bismuth tungstate (Bi₂WO₆) is a typical bismuth-based visible-light-responsive semiconductor photocatalyst that has attracted significant attention in the fields of environment remediation and energy conversion. In this paper, to address the issues of high photogenerated carrier recombination rate and limited visible-light-response range of Bi₂WO₆, various modification strategies are highlighted, including morphology control, element doping, heterojunction construction, carbon material compositing, and coupling with functional materials such as metal–organic frameworks (MOFs), covalent organic frameworks (COFs), or conductive polymers. Furthermore, the structure–activity relationships are discussed. On this basis, the latest application progress of Bi₂WO₆-based photocatalysts in fields such as pollutant degradation, antibacterial activity, and energy conversion and storage is summarized. Finally, prospects are put forward regarding the existing shortcomings and future development directions in the application of Bi₂WO₆-based photocatalysts, aiming to provide a systematic theoretical reference for the design and application of high-performance Bi₂WO₆-based photocatalysts. Full article

The extensive use of oxytetracycline (OTC) poses significant threats to aquatic ecosystems, necessitating efficient removal strategies. While photocatalytic technology is a promising approach, single catalysts, like UiO-66-NH₂ and Bi₂MoO₆, suffer from rapid photogenerated carrier recombination and narrow light absorption. To address this, a Z-scheme heterojunction photocatalyst, Bi₂MoO₆/UiO-66-NH₂, was synthesized via a solvothermal method to enhance OTC degradation. Characterization results showed that the composite expanded visible-light absorption and improved electron-hole separation. Under simulated sunlight, the optimized composite (BUN80) achieved an OTC removal efficiency of 87.68% within 120 min under optimized conditions. The catalyst retained photocatalytic activity over five consecutive cycles, although a decrease in removal efficiency was observed. Radical trapping experiments indicated that h⁺ and •O₂⁻ were the main reactive species, and a proposed Z-scheme charge transfer pathway was suggested based on band structure analysis and photoelectrochemical results. LC-MS analysis identified 17 intermediate products, and ECOSAR-based toxicity prediction suggested a decreasing trend in aquatic toxicity during the degradation process. These findings indicate that Bi₂MoO₆/UiO-66-NH₂ is a promising photocatalyst for OTC degradation in water. Full article

Semiconductor photocatalysis technology is a simple, efficient, and low-cost method for environmental pollution remediation. As a promising photocatalyst for oxidative degradation, titanium dioxide (TiO₂) demonstrates the capability to address energy shortages and environmental pollution issues. In this study, orange peel was used as the raw material to synthesize a (TiO₂-CdS-C₃N₄-CDs) TCCC composite photocatalyst containing natural green carbon dots via a one-pot hydrothermal method for the first time. This catalyst was applied to the catalytic degradation of multiple dye molecules (Rhodamine B, Methylene Green, Reactive Brilliant Blue KN-R) and quinolone antibiotic (Ciprofloxacin, CIP) as well as tetracycline antibiotic (Tetracycline, THC). Meanwhile, it provides more adsorption sites for target pollutants and loads electron reservoirs (CDs) on the TCC surface, promoting the separation of photogenerated carriers in pure TiO₂, thereby enhancing the visible light utilization and photocatalytic activity of the material. This work expands the application scope of semiconductor photocatalysis technology and TiO₂-based photocatalytic active substrates. Full article

Pure Bi₂O₃ is a favorable photocatalyst for visible-light-driven processes; however, the rapid recombination of photogenerated charge carriers limits its practical performance. In this work, Co-doped Bi₂O₃ nanoparticles, Co_xBi_2−xO₃ (x = 0–0.1), were produced through a sol–gel combustion route to enhance their visible-light photocatalytic activity. As demonstrated by XRD analysis, Co was successfully incorporated into the Bi₂O₃ lattice, along with changes to the crystal structure, crystallite size (up to ~88 nm), and lattice strain. Optical measurements revealed that Co-doping induces a clear absorption edge’s red shift, resulting in a systematic reduction of the optical band gap from 3.9 eV for pure Bi₂O₃ to approximately 3.1 eV for the doped samples. This band gap narrowing enhances visible-light absorption and improves photocatalytic efficiency. Photocatalytic activity was assessed by measuring the degradation of MB under visible-light irradiation. Incorporation of Co consistently enhanced the performance across all doped samples compared to the pristine oxide counterpart. The Co_0.1Bi_1.9O₃ composition demonstrated the best performance, achieving a removal efficiency of 94.5% within 120 min, compared with 73.0% for pure Bi₂O₃. Kinetic analysis indicated pseudo-first-order behavior, with the optimal sample showing a rate constant of 0.0240 min⁻¹—more than twice that of the undoped material (0.0105 min⁻¹). These results validate that Co-doping is an actual approach for engineering the electronic structure of Bi₂O₃, leading to enhanced visible-light absorption, improved charge-carrier separation, and significantly higher photocatalytic efficiency for environmental remediation applications. Full article

To improve the visible-light response and antibacterial performance of titanium dioxide, a TiO₂/GO/CdS mesoporous nanocomposite was prepared via an ultrasound-assisted sol–gel method in this study. Systematic characterizations including XRD, XPS, SEM, TEM, BET, UV-Vis DRS and FTIR were carried out to analyze the structure, morphology and optical properties of the material. The results show that the composite exhibits a typical mesoporous structure with a specific surface area of 197.0962 m²/g and a pore size distribution of 2–14 nm. CdS is successfully doped into the TiO₂ matrix and forms a heterostructure with GO. UV-Vis diffuse reflectance spectra indicate that the synergistic effect of CdS and GO significantly broadens the visible-light absorption range of TiO₂ and suppresses the recombination of photogenerated carriers. Antibacterial tests using Escherichia coli as the target strain demonstrate that the TiO₂/GO/CdS composite exhibits remarkably better visible-light photocatalytic bactericidal activity than pure TiO₂ and the TiO₂/GO composite. This work provides a new strategy for the modification of TiO₂-based photocatalytic antibacterial materials, and the as-prepared composite shows promising application prospects in the antibacterial field. Full article

Photocatalytic H₂O₂ production coupled with selective organic oxidation provides a promising strategy for simultaneously generating value-added oxidants and chemicals under mild conditions. Herein, Ni-modified defect-engineered NH₂-UiO-66 photocatalysts (Ni/UN) are constructed by introducing Ni species into a vacuum-treated NH₂-UiO-66 framework (UN). Compared with the original NH₂-UiO-66 and the defect-treated UN, Ni/UN exhibits weakened photoluminescence emission, enhanced transient photocurrent response, and reduced electrochemical impedance, indicating that the separation and transfer of photogenerated charge carriers have been improved. The band structure analysis further reveals that Ni/UN has a narrow band gap of approximately 2.52 electron volts and a slightly more negative conduction band position (−0.50 V), which is conducive to the photoinduced reduction reaction. The importance of O₂ in the photocatalytic process was demonstrated by changing the atmospheric conditions. Therefore, in the benzylalcohol system, under the oxygen atmosphere, Ni/UN achieved the highest H₂O₂ production rate of 3257 μmol g⁻¹ h⁻¹, accompanied by the continuous generation of benzaldehyde, with its content reaching 3420 μmol g⁻¹ after 60 min of irradiation. The scavenger experiment further indicates that photogenerated electrons and the active substances derived from oxygen are closely involved in the formation of H₂O₂, while the ·OH-related processes only play a limited contribution role. This study demonstrates an effective strategy for enhancing the performance of metal–organic framework (MOF)-based photocatalysts through defect engineering and metal coordination regulation, thereby achieving efficient photochemical production of hydrogen peroxide and the selective oxidation of benzyl alcohol. Full article

Ternary heterojunction photocatalysts enhance the separation and transport of photogenerated charge carriers, thereby boosting their redox activity for use in environmental and sustainable energy applications. This study focuses on the synthesis of a TiO₂/Bi₂O₃/g-C₃N₄ heterojunction composite via a ceramic method with TiO₂ loadings of 80%, 85%, and 90% (denoted 80T-BC, 85T-BC, and 90T-BC, respectively) to investigate structure–property–performance relationships in photocatalytic dye degradation. The structural, optical, and morphological properties of the synthesised materials were characterised using X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance UV–Vis spectroscopy (DRS). The photocatalytic performance was evaluated by measuring the degradation of Rhodamine B under visible light irradiation. Under optimised conditions (pH 6, initial RhB concentration of 5 mg/L, and a reaction time of 120 min), a degradation rate of 99% was achieved. Furthermore, the semiconductor demonstrated significant antibacterial activity against both Gram-negative (Pseudomonas aeruginosa) and Gram-positive (Staphylococcus aureus) bacteria. This study presents a promising strategy for modifying TiO₂-based semiconductors by incorporating different metal oxides. The formation of the resulting heterojunction significantly enhances photocatalytic efficiency, demonstrating strong potential for practical environmental remediation. Full article

In this study, zinc sulfide (ZnS) and manganese (Mn)-doped ZnS nanopowder were successfully prepared via a simple and cost-effective chemical precipitation method with various concentrations of Mn for use in UV photodetectors. The effects of Mn doping on the structural, morphological, and optoelectronic properties of ZnS nanopowder were studied. Structural analysis showed that all samples had a cubic structure with crystallite sizes approximately in the region of 2–3 nm. The morphological analysis using scanning electron microscopy confirmed the formation of well-dispersed spherical nanoparticles. Photoluminescence spectra show that Mn doping increased the luminescence intensity and caused a red shift in the emission peaks. Electrical properties such as conductivity and dielectric constant showed marked improvement with increasing Mn content. The conductivity increased from 3.7 mΩ⁻¹·m⁻¹ for pure ZnS to 6.3 mΩ⁻¹·m⁻¹ for the 1.03 mol% Mn²⁺ sample. The performance of photodetectors was evaluated under UV light. It was revealed that the photodetector based on a sample with 1.03 mol% Mn²⁺ reached an optimum state with an EQE of 9.8%, a detectivity of 4.65 × 10⁹ Jones, and a responsivity of 3.64 × 10⁻² A/W, indicating the effectiveness of Mn doping in improving the photo-generated carrier collection. Full article

The efficient photocatalytic generation of hydrogen peroxide (H₂O₂) from pure water remains a formidable challenge, primarily due to the rapid recombination of photogenerated electron–hole pairs and insufficient redox potentials inherent in single-component photocatalysts. To address these issues, we designed and synthesized a heterojunction material comprising cadmium sulfide nanoparticles loaded on carbon spheres (CS@CdS). Under conditions utilizing pure water and ambient air, the CS@CdS composite achieves an H₂O₂ production rate of 1305 μmol·g⁻¹·h⁻¹, which is 3.1 and 3.6 times higher than that of pure CdS and CS, respectively, without the need for any sacrificial agents or external oxygen supply. Systematic characterization reveals that CS and CdS form a tightly coupled electronic interface, which significantly accelerates charge carrier separation and effectively prolongs the lifetime of photogenerated carriers, thereby boosting photocatalytic performance. Furthermore, the CS component extends the visible-light absorption range of the composite and functions as an electron acceptor to suppress charge recombination, collectively endowing CS@CdS with enhanced photocatalytic activity. Mechanistic studies indicate that H₂O₂ production over CS@CdS proceeds predominantly via a two-step single-electron oxygen reduction reaction (ORR) pathway. This work offers a viable strategy for constructing CS-based heterojunction photocatalysts for efficient H₂O₂ synthesis. Full article

Graphitic carbon nitride (CN) is a promising photocatalytic material, but its practical application is limited by small specific surface area, narrow light absorption range, and high photogenerated carrier recombination rate. To address these issues, this study synthesized boron-doped carbon nitride (BCN) and sulfuric acid-exfoliated boron-doped carbon nitride (BCND). X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) results confirmed that boron was successfully doped into the CN skeleton via B-N bonds. Scanning electron microscopy (SEM) and N₂ adsorption–desorption (BET) characterizations showed that acid exfoliation significantly increased the specific surface area of BCND to 68.80 m²·g⁻¹, much higher than that of CN (9.54 m²·g⁻¹) and BCN (15.98 m²·g⁻¹). UV–visible diffuse reflectance spectroscopy (UV-Vis DRS) analysis revealed that BCND had the narrowest bandgap (2.59 eV) among the three materials, which enhanced its visible-light absorption efficiency. Photoelectrochemical tests demonstrated that BCND exhibited the smallest charge transfer resistance and the highest transient photocurrent density (eight times that of CN), indicating efficient separation of photogenerated electron–hole pairs. Photocatalytic water splitting experiments showed that BCND achieved the highest Hydrogen production rate of 792.34 μmol·g⁻¹·h⁻¹, which was about 4 times that of CN (158.41 μmol·g⁻¹·h⁻¹) and 1.36 times that of 2.5% BCN (584.30 μmol·g⁻¹·h⁻¹). Free-radical trapping experiments indicated that hydroxyl radicals (·OH) played a crucial promotional role in Hydrogen production, while superoxide anions (·O₂⁻) exerted an inhibitory effect. The enhanced performance of BCND was attributed to the synergistic effects of boron doping (narrowing bandgap) and acid exfoliation (increasing specific surface area). A possible photocatalytic Hydrogen production mechanism was proposed based on the experimental results. This study provides a feasible strategy for the structural modification and performance optimization of g-C₃N₄-based photocatalysts for water splitting. Full article

To improve the visible-light-driven photocatalytic degradation efficiency of g-C₃N₄-based photocatalysts toward organic pollutants, a MoS₂/g-C₃N₄ composite precursor was employed in this work, and the phase composition and defect environment of Mo species were regulated by post-annealing under air and N₂ atmospheres, respectively, thereby constructing Mo-based/g-C₃N₄ (MCN) composites with distinct structural evolution characteristics. The results showed that the photocatalytic activity of the as-sonicated MCN composite toward methylene blue (MB) was only moderately improved, among which the 15% loading sample exhibited the best performance with a degradation efficiency of about 42.0% within 60 min. In contrast, annealing at 400 °C under N₂ resulted in only a slight activity change, whereas the sample treated at 400 °C in air (Air-15% MCN) achieved an MB degradation efficiency of 99.9% within 60 min, together with a much higher pseudo-first-order reaction rate constant than that of the air-treated sample at a lower temperature. XRD, FT-IR and XPS analyses revealed that air annealing induced the conversion of MoS₂ into highly crystalline MoO₃ (or MoO_3−x), leading to the formation of a reconstructed MoO_3−x/g-C₃N₄ composite interface. Meanwhile, the increased high-binding-energy component in the O 1s spectrum and the EPR signal around g ≈ 2.00 further suggested the presence of more abundant defect-related centers in the air-treated sample. Although Air-15% MCN possessed a lower specific surface area than the untreated and N₂-treated samples, it displayed enhanced visible-light absorption, higher transient photocurrent response, lower interfacial charge-transfer resistance, and accelerated carrier dynamics, indicating that the activity enhancement mainly originated from atmosphere-induced phase transformation, interfacial reconstruction, defect-related active centers, and improved charge separation/transfer, rather than from the surface area effect. Based on the above results, a possible interfacial charge-transfer pathway is tentatively proposed for the g-C₃N₄/MoO_3−x interface formed after air treatment, which contributes to the efficient utilization of photogenerated carriers and the rapid degradation of MB. This work demonstrates that atmosphere-induced phase transformation is a simple and effective strategy for regulating the structure and photocatalytic performance of Mo-based/g-C₃N₄ composites, and provides useful guidance for the design of efficient visible-light photocatalysts. Full article