Search Results (18)

Enhancing the thermal conductivity of fluids by using nanoparticles with outstanding thermophysical properties has acquired significant attention for heat-transfer applications. Nanofluids have the potential to optimize energy systems by improving heat-transfer efficiency. In this study, cobalt ferrite nanoparticles clusters with controlled mean sizes ranging from 97 to 192 nm were synthesized using a solvothermal method to develop novel nanofluids with enhanced thermal conductivity. These clusters were comprehensively characterized using transmission electron microscopy, X-ray diffraction, Raman spectroscopy, vibrating-sample magnetometry, and nitrogen physisorption. The CoFe₂O₄ cluster nanofluids were prepared using the two-step method with various base fluids (water, propylene glycol, and a mixture of both). Dynamic light scattering analyses of the average Z-size of the dispersed nanoadditives over time revealed that the stability of the dispersions is influenced by cluster size and the proportion of glycol in the base fluid. The thermal conductivity of the base fluid and nine different 0.5 wt% CoFe₂O₄ cluster nanofluids was measured using the transient hot wire method at temperatures of 293.15, 303.15, and 313.15 K, showing different temperature dependencies. The study also explores the relationships between the thermal conductivity, cluster size, and specific surface area of the nanoadditives. A maximum thermal conductivity enhancement of 4.2% was reported for the 0.5 wt% nanofluid based on propylene glycol containing 97 nm CoFe₂O₄ clusters. The findings suggest that the specific surface area of nanostructures is a more relevant parameter than size for describing improvements in thermal conductivity. Full article

The increased voltage loading of transformers has led to research on improving transformers’ lifespans to meet demand. Insulation oil acts as cooling medium that can significantly affect the performance of a transformer. This paper discusses an experimental study on the influences of the doping of carbon nanotube (CNT) particles and magnetic fields on the electrical properties of mineral oil (MO). An analysis of electrical properties was conducted using AC breakdown tests, Tan Delta tests, Raman measurements, and simultaneous thermal analysis. Proper preparation was considered before starting the analysis of the electrical properties. The AC breakdown voltages before and after modification were measured. The experiment results indicated that the AC breakdown of mineral oil with a suitable amount of carbon nanotube particles (0.005 g/L) and a suitable magnetic field (0.45 T) gives the highest breakdown voltage. It was found that the proper treatment of nanofluid also greatly influences breakdown voltage. Additionally, Raman measurements analyzed the physical changes in the samples. From the results obtained, the addition of carbon nanotubes and the magnetic field of mineral oil leads to an improved performance of the transformer. Full article

The reputation of nanofluids as a convenient heat transfer media has grown in recent years. The synthesis of nanofluids is often challenging, particularly carbon-based nanofluids, due to the rapid agglomeration of the nanoparticles and the instability of the nanofluids. In this regard, surface modification and surfactant addition are potential approaches to improve the physical and thermal properties of carbon-based nanofluids that have been studied and the structural, morphological, and thermal characteristics of surface-oxidised carbon nanofibre (CNF)-based nanofluids has been characterised. Commercial CNF was first subjected to three different acid treatments to introduce surface oxygen functional groups on the CNF surface. Following the physical and thermal characterisation of the three surface-oxidised CNFs (CNF-MA, CNF-MB, and CNF-MC), including Raman spectroscopy, Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and field emission scanning electron microscopy (FESEM), the CNF-MB was selected as the best method to synthesise the surface-oxidised CNF-based nanofluid. A total of 40 mL of ultrapure water was used as a pure base fluid and mixed with the surface-oxidised CNF at a concentration range of 0.1–1.0 wt.%, with a fixed of 10 wt.% amount of polyvinylpyrrolidone (PVP). The thermal conductivity of CNF-based nanofluid was then characterised at different temperatures (6, 25, and 40 °C). Based on the results, surface oxidation via Method B significantly affected the extent of surface defects and effectively enhanced the group functionality on the CNF surface. Aside from the partially defective and rough surface of CNF-MB surfaces from the FESEM analysis, the presence of surface oxygen functional groups on the CNF wall was confirmed via the Raman analysis, TGA curve, and FTIR analysis. The visual sedimentation observation also showed that the surface-oxidised CNF particles remained dispersed in the nanofluid due to the weakened van der Waals interaction. The dispersion of CNF particles was improved by the presence of PVP, which further stabilised the CNF-based nanofluids. Ultimately, the thermal conductivity of the surface-oxidised CNF-based nanofluid with PVP was significantly improved with the highest enhancement percentage of 18.50, 16.84, and 19.83% at 6, 25, and 40 °C, respectively, at an optimum CNF concentration of 0.7 wt.%. Full article

Nanofluids have become of interest in recent years thanks to their improved thermal properties, which make them especially interesting for microchannel heat sink applications. In this study, we prepared two aqueous nanofluids based on reduced graphene oxide (rGO) decorated with manganese dioxide (MnO${}_2$) at a concentration of 0.1 wt.%. The difference between the two nanofluids was in the preparation of the reduced graphene oxide decorated with MnO${}_2$. In the first case, the manganese salt was mixed with ascorbic acid before GO reduction with NaOH, and in the second case, the GO reduction with NaOH occurred under ascorbic acid. Ascorbic acid not only plays the role of a non-toxic and ecofriendly reducing agent but also acts as an important parameter to control the reaction kinetics. The structural, microstructural and spectral characterizations of the MnO${}_2$/rGO nanocomposite were conducted via X-ray diffractometry (XRD), Raman spectroscopy, FT-IR, TEM, SEM and EDS analyses. Moreover, the synthesized MnO${}_2$/rGO nanocomposites were utilized as nanofluids and their stability, thermal conductivity and rheological behaviors were studied. The thermal conductivity of the MnO${}_2$/rGO and MnO${}_2$AsA/rGO nanofluids was 17% and 14.8% higher than that of water for the average temperature range, respectively, but their viscosity remained statistically equal to that of water. Moreover, both nanofluids presented Newtonian behavior in the analyzed shear rate range. Therefore, both MnO${}_2$/rGO and MnO${}_2$AsA/rGO nanofluids are promising alternatives for use in applications with micro- and millichannel heat sinks. Full article

In this paper, we present a study on thermal conductivity and viscosity of nanofluids containing novel atomic layer deposition surface-modified carbon nanosphere (ALD-CNS) and carbon nanopowder (ALD-CNP) core-shell nanocomposites. The nanocomposites were produced by atomic layer deposition of amorphous TiO₂. The nanostructures were characterised by scanning (SEM) and transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDX), Fourier transform infrared spectroscopy (FT-IR), Raman spectroscopy, thermogravimetry/differential thermal analysis (TG/DTA) and X-ray powder diffraction (XRD). High-concentration, stable nanofluids were prepared with 1.5, 1.0 and 0.5 vol% nanoparticle content. The thermal conductivity and viscosity of the nanofluids were measured, and their stability was evaluated with Zeta potential measurements. The ALD-CNS enhanced the thermal conductivity of the 1:5 ethanol:water mixture by 4.6% with a 1.5 vol% concentration, and the viscosity increased by 37.5%. The ALD-CNS increased the thermal conductivity of ethylene–glycol by 10.8, whereas the viscosity increased by 15.9%. The use of a surfactant was unnecessary due to the ALD-deposited TiO₂ layer. Full article

In this study, multi-walled carbon nanotubes (MWCNTs) were chemically modified using three acid treatment methods to introduce the surface oxygen functional group (SOFG). The presence of SOFG on the MWCNTs has been characterized by Fourier Transform Infrared (FTIR) spectroscopy. Morphology, structural and thermal properties were performed using Field Emission Scanning Electron Microscopy (FESEM), Raman spectroscopy, and Thermogravimetric analysis (TGA), respectively. The result shows that the modification with acid treatment significantly affects the degree of defects and surface group functionality of surface oxidized MWCNTs from method B. The preparation of nanofluids using MWCNTs produced from method B (MWCNT-MB) was prepared using two different parameters: with and without polyvinylpyrrolidone (PVP) as surfactant. The experiment was conducted by setting variable carbon particle concentration from 0.1 wt.% to 1.0 wt.%, and the amount of PVP is 10% of carbon particles at different temperatures (6 °C, 25 °C, 40 °C). Based on visual observation, the dispersion of carbon particles was enhanced by the presence of PVP as the stabilizing agent. The thermal conductivity performance of nanofluids revealed that the surface oxidized MWCNTs with PVP show enhanced thermal conductivity compared to the nanofluid containing MWCNTs without PVP. The improvement contributes to this in terms of stability and homogenization of nanoparticles. Hence the improved distribution of MWCNTs in water-based media improves thermal conductivity. These promising properties of MWCNTs in water-based fluids would enable the nanofluids to be used in heat transfer fluid and cooling applications. Full article

This century is experiencing a generation of nanotechnologies that makes use of the remarkable properties of nanofluids in applications such as electrical systems, industrialization, and others. In this paper, mineral oil (MO) and palm oil (PO), with multi-walled carbon nanotube (CNT), have been synthesized for use in oil-filled transformer applications. This research aims to use Raman characterization to assess the feasibility of CNT nanofluids samples at 0.02 g/L and 0.03 g/L concentrations. The chemical structure bonding that exists in the Raman band between 700 cm⁻¹ and 3100 cm⁻¹ regions is identified and analyzed, accordingly. After baseline removal and normalization, the precision band location and intensity of oil samples are fitted with a Gaussian profile. It was discovered that the peak at ~1440 cm⁻¹ has the highest intensity for six oil samples, which is attributed to the (C–H) methylene scissors vibration of the CH₂ group. Based on the FWHM profile and integrated area under the curve of PO, it was discovered that CNT contributes to the structural stability defect of PO. Principal component analysis (PCA) is also used in this study to classify different samples based on chemical composition and identify the spectral characteristics with the highest degree of variability. Full article

Structural disorder and temperature behavior of specific heat in multi walled carbon nanotubes (MWCNTs) have been investigated. The results of X-ray diffractometry, Raman spectroscopy, and transmission electron microscopy (TEM) images are analyzed. The thermodynamic theory of the zigzag-armchair domain structure formation during nanotube synthesis is developed. The influence of structural disorder on the temperature behavior of specific heat is investigated. The size of domains was estimated at ~40 nm. A decrease in heat capacity is due to this size effect. The revealed dependence of the heat capacity of MWCNTs on the structural disorder allows control over thermal properties of nanotubes and can be useful for the development of thermoelectric, thermal interface materials and nanofluids based on them. Full article

Nanofluids obtained from halloysite and de-ionized water (DI) were prepared by using surfactants and changing pH for heat-transfer applications. The halloysite nanotubes (HNTs) nanofluids were studied for several volume fractions (0.5, 1.0, and 1.5 vol%) and temperatures (20, 30, 40, 50, and 60 °C). The properties of HNTs were studied with a scanning electron microscope (SEM), energy-dispersive X-ray analysis (EDX), Fourier-transform infrared (FT-IR) spectroscopy, X-ray powder diffraction (XRD), Raman spectroscopy and thermogravimetry/differential thermal analysis (TG/DTA). The stability of the nanofluids was proven by zeta potentials measurements and visual observation. With surfactants, the HNT nanofluids had the highest thermal conductivity increment of 18.30% for 1.5 vol% concentration in comparison with the base fluid. The thermal conductivity enhancement of nanofluids containing surfactant was slightly higher than nanofluids with pH = 12. The prepared nanofluids were Newtonian. The viscosity enhancements of the nanofluid were 11% and 12.8% at 30 °C for 0.5% volume concentration with surfactants and at pH = 12, respectively. Empirical correlations of viscosity and thermal conductivity for these nanofluids were proposed for practical applications. Full article

High-quality graphene is an especially promising carbon nanomaterial for developing nanofluids for enhancing heat transfer in fluid circulation systems. We report a complete study on few layer graphene (FLG) based nanofluids, including FLG synthesis, FLG-based nanofluid preparation, and their thermal conductivity. The FLG sample is synthesized by an original mechanical exfoliation method. The morphological and structural characterization are investigated by both scanning and transmission electron microscopy and Raman spectroscopy. The chosen two-step method involves the use of thee nonionic surfactants (Triton X-100, Pluronic^® P123, and Gum Arabic), a commercial mixture of water and propylene glycol and a mass content in FLG from 0.05 to 0.5%. The thermal conductivity measurements of the three FLG-based nanofluid series are carried out in the temperature range 283.15–323.15 K by the transient hot-wire method. From a modeling analysis of the nanofluid thermal conductivity behavior, it is finally shown that synergetic effects of FLG nanosheet size and thermal resistance at the FLG interface both have significant impact on the evidenced thermal conductivity enhancement. Full article

This paper intends to prepare a nanofluid sample by suspending Multi-walled Carbon Nanotubes (MWCNTs) at 0.005g/L concentration and analyze the behavior of electrical and dielectric properties based on the International Electrotechnical Commision test method. In order to validate the effectiveness of MWCNT nanofluid, alternating current breakdown voltage (BDV), negative polarity lightning impulse (LI), dielectric permittivity, dissipation factor (DF), DC resistivity and Raman structural measurement are executed accordingly. In the following, an analysis of the statistical distribution using the two-parameter Weibull distribution law of BDV and LI are evaluated at four experimental conditions to predict the probability of breakdown occurring at different percentages. Based on the observation, the MWCNT filler has a substantial effect in improving the BDV and LI characteristics of disposed mineral oil. The permittivity, DF and resistivity performance of MWCNT nanofluid from 25 °C to 90 °C also produces comparable and reliable performance as a fresh transformer oil. As for Raman structure, the revolution of transformer oil by doping MWCNT does not disrupt the original chemical structure of mineral oil. Hence, this study proves the improvement of the electrical and the behavior of dielectric properties and chemical structure of nanofluid, providing a huge contribution towards the development of insulating materials for transformer application. Full article

Transparent conductive films are fundamental materials, currently used in several fields. Recently, due to their unique multifunctional properties, composite materials have started to be used in place of fluorine tin oxide and indium tin oxide in transparent conductive electrodes. However, the production of composite materials is still complicated and involves toxic chemicals. Through a simple and environmentally-friendly method, we synthesized new composite materials—conductive, transparent, and flexible films—that can be applied to the production of modern optoelectronic devices. An even dispersion of the nanoparticles was achieved by ultrasound excitation. Moreover, a series of morphological and structural investigations were conducted on the films by scanning and transmission electron microscopy, electrical conductivity, Raman spectroscopy, X-ray diffraction and testing their sheet resistance. The results indicated that the tested composite materials were ideal for film coating. The nanofluids containing multi-walled carbon nanotubes presented the highest electrical conductivity; nevertheless, all the composite nanofluids tended to have relatively high electrical conductivities. The flexible films with composite structures presented lower sheet resistances than those with single structures. Finally, the hybrid materials showed a higher transmittance. Full article

It is well known that by dispersing nanoparticles in a fluid, the thermal conductivity of the resulting nanofluid tends to increase with the concentration of nanoparticles. However, it is not clear what the mechanism behind this phenomenon is. Raman spectroscopy is a characterization technique connecting the molecular and macroscopic world, and therefore, it can unravel the puzzling effect exerted by the nanomaterial on the fluid. In this work, we report on a comparative study on the thermal conductivity, vibrational spectra and viscosity of graphene nanofluids based on three different amides: N, N-dimethylacetamide (DMAc); N, N-dimethylformamide (DMF); and N-methyl-2-pyrrolidinone (NMP). A set of concentrations of highly stable surfactant-free graphene nanofluids developed in-house was prepared and characterized. A correlation between the modification of the vibrational spectra of the fluids and an increase in their thermal conductivity in the presence of graphene was confirmed. Furthermore, an explanation of the non-modification of the thermal conductivity in graphene-NMP nanofluids is given based on its structure and a peculiar arrangement of the fluid. Full article

Multiwalled carbon nanotubes (MWCNTs) have excellent electrical conductivity and good chemical stability, and are used as counter electrodes in dye-sensitized solar cells (DSSCs). The counter electrodes collect electrons from the external circuit and catalyze the redox reaction in the electrolyte. Electrocatalysis is an important step for generating energy from triiodide reduction in DSSCs. In this study, chemically treated MWCNTs were investigated for improving the photovoltaic performance of DSSCs. The MWCNTs were modified through chemical oxidation with sulfuric acid/nitric acid (H₂SO₄/HNO₃) or potassium persulfate/sodium hydroxide (K₂S₂O₈/NaOH). Nanocellulose (CNC) was used as a dispersant to improve the photovoltaic performance and dispersibility as an alternative material for counter electrodes in DSSCs. The counter electrodes were prepared on fluorine-doped tin oxide (FTO) glass substrates by spin coating nanofluids. Morphological and structural investigations were performed using scanning transmission electron microscopy (TEM), Fourier-transform infrared (FTIR) spectroscopy, and Raman spectroscopy. The electrical conductivity and UV light absorption of the DSSCs were analyzed to evaluate their photovoltaic performance. The results of these analyses showed that chemical functionalization and addition of CNC were effective for increasing the electrical conductivity and UV light absorption. Finally, all result trends were the same. Increasing the dispersibility of the counter electrode was found to improve the reduction of I₃⁻ at the interface between the MWCNTs and the electrolyte, thereby, improving the energy conversion efficiency. Full article

Nanofluids are systems with several interesting heat transfer applications, but it can be a challenge to obtain highly stable suspensions. One way to overcome this challenge is to create the appropriate conditions to disperse the nanomaterial in the fluid. However, when the heat transfer fluid used is a non-polar organic oil, there are complications due to the low polarity of this solvent. Therefore, this study introduces a method to synthesize TiO₂ nanoparticles inside a non-polar fluid typically used in heat transfer applications. Nanoparticles produced were characterized for their structural and chemical properties using techniques such as X-ray Diffraction (XRD), Raman spectroscopy, Transmission Electron Microscopy (TEM), Fourier Transform Infrared (FTIR) spectroscopy, and X-ray photoelectron spectroscopy (XPS). The nanofluid showed a high stability, which was analyzed by means of UV-vis spectroscopy and by measuring its particle size and ζ potential. So, this nanofluid will have many possible applications. In this work, the use as heat transfer fluid was tested. In this sense, nanofluid also presented enhanced isobaric specific heat and thermal conductivity values with regard to the base fluid, which led to the heat transfer coefficient increasing by 14.4%. Thus, the nanofluid prepared could be a promising alternative to typical HTFs thanks to its improved thermal properties and high stability resulting from the synthesis procedure. Full article