Search Results (127)

Battery storage systems are becoming very popular around the world. However, they are mainly used in industry for high-performance applications. Domestic use is still sporadic due to size and cost issues. This work overviews basic conceptual designs for a cost-effective battery storage system. The main specificity of the proposed systems is the use of commonly available recycled batteries from household appliances such as laptops and backup power supplies. The circuit topology considered is a 3S (three cells in series) configuration. This is because such wiring arrangements are those that are most often found in the home appliances described here. The technical solutions of the device itself focus on the ratio of the efficiency of the whole system to the production cost. Given the above, attention was paid to the simulation analysis of the operating modes, which directly influenced the components’ price. Changing the switching control scheme of the power transistors makes it possible to reduce the requirements for the driving components used with minimal impact on the power conversion efficiency (Δη 1–4%). According to the established findings, a prototype was made on which the simulation findings were verified; then, we further focused on the experimental measurement of the efficiency of the MPPT converter and conducted an analysis of a methodology in which we measure the deviation from the actual point of maximum power. The simple possibility of parallelizing the individual storage devices will again help improve the system’s overall efficiency. This makes the system suitable for use in small spaces such as houses, garages, cellars, etc. Full article

Electric vehicles (EVs) are a sustainable means of transportation, with their onboard batteries being crucial for both performance and energy management. A modular and reconfigurable power converter topology to connect removable batteries to the main DC bus of an EV is proposed in this paper. By employing Dual Active Bridge (DAB) converters in an Input Parallel Output Series (IPOS) configuration, the proposed topology is compatible with 400 V and 800 V standards without the need for external switches. The research explored the possibility to apply a very simple control strategy based on independent linear regulators. A theoretical analysis of the IPOS DAB converter is presented and the design of independent control regulators which minimize the coupling effect between the control variables is addressed. The stability of the IPOS DAB converter could be ensured using the proposed simplistic approach, enabling us to drastically simplify the regulator design step. The dynamic performance of the system was confirmed by means of a simulation and experimentally. Full article

Solid-state DC circuit breakers provide crucial support for the safe and reliable operation of low-voltage DC distribution networks. A hardware topology based on a cascaded structure with dual-stage, current-limiting, small-capacity, solid-state DC circuit breakers has been proposed. The hardware topology uses a series–parallel configuration of cascaded SCR (thyristors) and MOSFETs (metal oxide semiconductor field-effect transistors) in the transfer branch, which enhances the breaking capacity of the transfer branch. Additionally, a secondary current-limiting circuit composed of an inductor and resistor in parallel is integrated at the front end of the transfer branch to effectively improve the current-limiting performance of the circuit breaker. Meanwhile, a dissipation branch is introduced on the fault side to reduce the energy consumption burden on surge arresters. For the power supply system of the hardware part, a capacitor-powered method is adopted for safety and efficiency, with a capacitor switch serially connected to the capacitor power supply for high-precision control of the power supply. Current detection branches are introduced into each branch to provide conditions for the on–off control of semiconductor switching devices and experimental data analysis. The high-frequency control of semiconductor devices is achieved using optocoupler signal isolation chips and high-speed drive chips through a microcontroller STM32. Simulation verification based on MATLAB/SIMULINK software and experimental prototype testing have been conducted, and the results show that the hardware topology is correct and effective. Full article

In electric powertrain traction applications, the adopted trend to improve the performance and efficiency of electromechanical power conversion systems is to increase supply voltages and inverter switching frequencies. As a result, electrical machine conductors are subjected to ever-increasing electrical stresses, leading to premature insulation degradation and eventual short-circuits. Winding condition monitoring is crucial to prevent such critical failures. Based on the scientific literature, several methods can be used for early identification of aging. A first solution is to monitor partial discharges. This method requires the use of a specific measurement device and an undisturbed test environment. A second solution is to monitor the inter-turn winding capacitance, which is directly related to the condition of the insulation and can cause a change in the stator impedance behavior. Several approaches can be used to estimate or characterize this impedance behavior. They must be performed on a machine at standstill, which limits their application. In this paper, a new characterization method is proposed to monitor the high-frequency stator impedance evolution of voltage source inverter-fed machines. This method can be applied at any time without removing the machine from its operating environment. The range and accuracy of the proposed frequency characterization depend in particular on the supply voltage level and the bandwidth of the measurement probes. The effects of parameters such as temperature, switching frequency, and DC voltage amplitude on the impedance characteristic were also studied and will be presented. Tests carried out on an automotive traction machine have shown that the first two series and parallel resonances of the high-frequency impedance can be accurately identified using the proposed technique. Therefore, by monitoring these resonances, it is possible to predict the aging rate of the conductor. Full article

Theoretical and experimental work for a novel topology of DC-DC boost switching capacitor converter is introduced in this paper. This new design is an adjustment for boost series and parallel topology developed by Makowski. Thus, a comparison between the two designs presented in this paper aims to highlight the improvement in the conversion rate of the boost converter’s output voltage while using the same number and size of capacitors. Converter analyses for both with and without load are presented. Also, a boost converter with a nonlinear ferroelectric capacitor is presented to further increase the boost converter conversion rate using advantages of the ferroelectric capacitors, such as their big dielectric constant and polarization reversal. Full article

The high-thrust linear motor used for the electromagnetic launch is switched by switches composed of anti-shunt thyristors. During the switching process, different current path states will appear, which will lead to changes in motor parameters and current fluctuation. Focusing on the air-core synchronous linear motor with parallel and series power supply, this paper analyzes the change in current path caused by the change in the trigger signal of anti-parallel thyristors in the process of sectionalized stator switching. The motor circuit model of the switching process is derived. A new sectionalized stators switching method is proposed to realize the smooth switching of the sectionalized stators linear motor. Finally, the correctness of the analysis and modeling is verified by simulation, and the effectiveness of the sectionalized stators switching method is tested by using the test prototype. Full article

This article presents a power-efficient DC-DC converter based on a switched-capacitor (SC) cell in power management systems supplied for fully integrated photovoltaic (PV) modules. These modules shall provide high-performance point-of-load voltage regulation. The primary objective of this study is to better utilize capacitance and switches by selecting a proper SC topology in order to improve the power efficiency of SC converters. A general steady-state performance model is investigated to optimize and compare a variety of SC DC-DC topologies. The investigation method relies on a charge-multiplier approach and considers the impact of area constraint on capacitors. To identify the most suitable topology for a given conversion ratio, the performance-limit metrics of SC converters are calculated. The analysis provides framework to determine optimum switch size and switching frequency for a two-phase 3:1 series–parallel converter for a target load current of 10 mA implemented on a 22 nm process technology. The results shows that a minimum of 250 MHz switching frequency is desirable for achieving a target efficiency greater than 85% while maintaining the minimum output voltage of 0.34 V. The analysis results are verified through MATLAB and PSpice-based simulations. Full article

This paper presents a novel optoelectronic transimpedance amplifier (OTA) for short-range LiDAR sensors used in 180 nm CMOS technology, which consists of a main transimpedance amplifier (m-TIA) with an on-chip P⁺/N-well/Deep N-well avalanche photodiode (P⁺/NW/DNW APD) and a replica TIA with another on-chip APD, not only to acquire circuit symmetry but to also obtain concurrent automatic gain control (AGC) function within a narrow single pulse-width duration. In particular, for concurrent AGC operations, 3-bit PMOS switches with series resistors are added in parallel with the passive feedback resistor in the m-TIA. Then, the PMOS switches can be turned on or off in accordance with the DC output voltage amplitudes of the replica TIA. The post-layout simulations reveal that the OTA extends the dynamic range up to 74.8 dB (i.e., 1 µA_pp~5.5 mA_pp) and achieves a 67 dBΩ transimpedance gain, an 830 MHz bandwidth, a 16 pA/$\surd \mathrm{Hz}$ noise current spectral density, a −31 dBm optical sensitivity for a 10⁻¹² bit error rate, and a 6 mW power dissipation from a single 1.8 V supply. The chip occupies a core area of 200 × 120 µm². Full article

We propose a method for increasing power extraction from a thermoelectric generator (TEG) by switching between series/parallel circuit configurations of thermoelectric elements, which can adjust the internal impedance of the TEG. The power characteristics of the TEG can be adjusted to the load characteristics of the connected device and the relevant ambient temperature. In this paper, we analyzed the change in the TEG characteristics with the series/parallel switching function. We evaluated the power supply to the connected devices at different ambient temperatures and different series/parallel configurations and confirmed that the extracted power could be increased. By theoretically analyzing the circuit configuration of the thermoelectric devices, the switching required to improve the power extraction, and the temperature difference at which switching occurred, we devised a design method for a TEG with circuit switching in order to increase power extraction with any device. We demonstrated the configuration of switching by using a system in which a TEG supplied power to an external wireless transmitter circuit. In this system, the optimal configuration differed at temperature differences of 3.0 K and 4.0 K. At a temperature difference of 3.0 K, the 2-series/1-parallel configuration provided 10% more power to the external circuit than the 1-series/2-parallel configuration. On the other hand, at the temperature difference of 4.0 K, the 1-series/2-parallel configuration provided 23% more power than the 2-series/1-parallel configuration. Full article

This paper analyzes, designs and implements a reconfigurable phase-shifted full-bridge (PSFB) converter. It adopts the topology of the traditional PSFB converter and incorporates clamping circuits to solve some fundamental problems of conventional topology. In addition, auxiliary switches are employed for output reconfiguration, which allows expanding the output voltage range without compromising the system efficiency. Single pole double throw (SPDT) mechanical switches are used to realize series and parallel connections. In this paper, the characterization of the PSFB converter with clamping circuit and its design considerations are discussed. A 10 kW prototype with a power density of 0.485 W/cm³, 900 V input voltage and 400/800 V nominal output voltage was manufactured. The experimental results validated the analysis and confirmed the high conversion efficiency for a wide load range; an efficiency of 96.69% was obtained for the full load condition. Full article

Transformerless inverters have been extensively deployed in photovoltaic (PV) applications, owing to features such as high efficiency, high power quality, and low cost. However, the leakage current in such inverters due to the absence of galvanic isolation has resulted in several topological modifications. This paper introduces a single-input switched-capacitor (SC)-based multilevel inverter (MLI) that is capable of eliminating the leakage current due to its common-ground structure. Also, the proposed inverter has the capability of single-stage voltage boosting, which is essential in PV systems. The series–parallel switching facilitates the self-balancing of SCs, which, in turn, assists in voltage boosting. Moreover, the proposed MLI synthesizes a seven-level output using only eight switches. Following an in-depth analysis of the circuit operation, modulation scheme, and power losses, a detailed comparison among recently developed seven-level MLIs is carried out, which verifies the design's superiority. Extensive simulation and experimental results are presented to validate the prominent features of the seven-level MLI under dynamic operating conditions. Full article

Newly introduced Photovoltaic (PV) devices, featuring a built-in chip with an illuminating Light Emitting Diode (LED), have emerged in the commercial market. These devices are touted for their utility as both low- and high-side power switch drivers and for data acquisition coupling. However, comprehensive knowledge and experimentation regarding the limitations of these Photovoltaic Drivers in both switching and signal processing applications remain underexplored. This paper presents a detailed characterization of a Photovoltaic Driver, focusing on its performance under resistive and capacitive loads. Additionally, it delineates the device’s constraints when employed in signal processing. Through the analysis of switching losses across various power switches (Silicon and Silicon Carbide) in both series and parallel driver configurations, this study assesses the driver’s efficacy in operating Junction Field-Effect Transistors (JFETs). Findings suggest that Photovoltaic Drivers offer a low-cost, compact solution for specific applications, such as high-voltage, low-bandwidth measurements, and low-speed turn-on with fast turn-off power switching scenarios, including solid-state switches and hot-swap circuits. Moreover, they present a straightforward, cost-effective method for driving JFETs, simplifying the circuit design and eliminating the need for an additional negative power source. Full article

This article describes a 17-level switched-capacitor-based eight-times-boosting gain inverter. The inverter is made up of a DC power source, thirteen switches, three diodes, and three capacitors. The inverter produces seventeen steps during each cycle and crosses the zero line two times in one complete cycle. The proposed inverter has its polarity change mechanism; it is not necessary to use an H-bridge. Three self-balancing capacitors make up this construction. The capacitors automatically balance voltage by connecting in series/parallel to the input voltage source. Logic gates can generate gate pulses with the phase disposition pulse-width modulation technique, which helps to preserve capacitor voltage balance at the same time. The proposed structure was compared to recent papers, analyzing factors including voltage gain, DC sources, semiconductor devices, cost function, and TSV. The proposed configuration offers cost effectiveness and fewer semiconductor devices for providing a 17-level output with sufficient voltage gain. Also, to reduce the capacitor inrush current, soft charging is used. Additionally, the proposed structure’s power losses were examined, confirming its efficiency. Finally, an experimental prototype was tested to analyze and validate the suggested structure’s performance under various situations. Results show the proposed structure performs well under steady and dynamic situations. Full article

In order to achieve high and low voltage isolation transformation in DC transmission and distribution networks, a multi module input-series output-parallel (ISOP) system consisting of a buck/boost converter and a CLLLC resonant converter as submodules was studied. This system can ensure that the CLLLC converter operates in the optimal state during frequency changes, achieves a soft switching function, and maintains a high conversion efficiency. This article establishes a mathematical model of a cascaded converter, analyzes its gain characteristics, and proposes a fuzzy PID three-loop control strategy to achieve good input voltage and output current sharing in the ISOP system. A simulation model is built on the MATLAB(R2023a)/Simulink platform to verify the effectiveness and superiority of the proposed control strategy. Finally, by building a prototype platform, the feasibility of the ISOP system and the effectiveness of fuzzy PID three-loop control were verified through experiments. Full article

Memristors, since their inception, have demonstrated remarkable characteristics, notably the exceptional reconfigurability of their memory. This study delves into electroforming-free ${\mathrm{YMnO}}_3$ (YMO)-based resistive switches, emphasizing the reconfigurable memory effect in multiferroic YMO thin films with metallically conducting electrodes and their pivotal role in achieving adaptable frequency responses in impedance circuits consisting of reconfigurable YMO-based resistive switches and no reconfigurable passive elements, e.g., inductors and capacitors. The multiferroic YMO possesses a network of charged domain walls which can be reconfigured by a time-dependent voltage applied between the metallically conducting electrodes. Through experimental demonstrations, this study scrutinizes the impedance response not only for individual switch devices but also for impedance circuitry based on YMO resistive switches in both low- and high-resistance states, interfacing with capacitors and inductors in parallel and series configurations. Scrutinized Nyquist plots visually capture the intricate dynamics of impedance circuitry, revealing the potential of electroforming-free YMO resistive switches in finely tuning frequency responses within impedance circuits. This adaptability, rooted in the unique properties of YMO, signifies a paradigm shift heralding the advent of advanced and flexible electronic technologies. Full article