Search Results (145)

This study investigates the enhancement of polyvinylidene fluoride (PVDF) membranes with polyethylene glycol (PEG) to improve their efficacy in treating tofu wastewater through the ultrafiltration (UF) process. PVDF membranes with varying PEG concentrations of 0, 0.5, 1, and 1.5% in the dope solution were produced, characterized via FTIR, mechanical strength, porosity, and contact angle measurements, and evaluated in wastewater treatment at varying pressures of 3, 4, and 5 bar in the UF process. The incorporation of PEG increased the membrane’s porosity from 28.2% for M-0 to 43.5% for M-1.5. The contact angle decreased from 65.3° for M-0 to 53.3° for M-1.5, indicating an increase in hydrophilicity. Elongation increased from 36.0% for M-0 to 113.5% for M-1.5; however, the tensile strength decreased from 11.8 MPa for M-0 to 5.4 MPa for M-1.5. Although PEG-modified membranes demonstrated enhanced flux, with values of 6.3 L∙m⁻²∙h⁻¹ for M-0 and 15.7 L∙m⁻²∙h⁻¹ for M-1.5 at a pressure of 5 bar, pure PVDF membranes (M-0) showed greater rejection rates for chemical oxygen demand (COD), total dissolve solid (TDS), total suspended solid (TSS), and turbidity at 3 bar, achieving values of 66.3%, 41.6%, 99.6%, and 99.1%, respectively. Following ultrafiltration, the pH and TDS levels conformed to Indonesian government guidelines; however, the COD levels were non-compliant, indicating the need for additional treatment. The findings suggest that PVDF/PEG ultrafiltration membranes are suitable for pre-treatment; however, nanofiltrationor reverse osmosis may be necessary to meet the stringent regulatory standards for tofu wastewater treatment. The modified M-1.5 membrane is recommended as the primary ultrafiltration membrane for tofu wastewater treatment due to its superior flux, prior to nanofiltration or reverse osmosis, to comply with the stringent regulatory standards established by the Government of the Republic of Indonesia. Full article

As sensitive parts of the water treatment process, reverse osmosis (RO) membranes are the most important for desalination and wastewater treatment. But the performance of RO membranes deteriorates over time due to fouling, necessitating frequent replacements. One of the environmental challenges is the disposal of End-of-Life (EoL) RO membranes, which are made of non-biodegradable polymers. The reuse of EoL membranes as a sustainable approach for waste saving and resource efficiency has recently attracted considerable attention. The present work provides a comprehensive overview of the strategies for reusing EoL RO membranes as sustainable alternatives to conventional disposal methods. Furthermore, the fundamental principles of RO technology, the primary types and impacts of membrane fouling, and advanced cleaning and regeneration techniques are discussed. The conversion of EoL membranes into nanofiltration (NF), ultrafiltration (UF), and forward osmosis (FO) membranes is also covered in this review, as well as their uses in brackish water desalination, dye/salt separation, groundwater treatment, and household wastewater reuse. Environmental and economic benefits, as well as technical, social, and regulatory challenges, are also discussed. Finally, the review highlights innovative approaches and future directions for incorporating EoL membrane reuse into circular economy models, outlining its potential to improve sustainability and reduce operational costs in water treatment systems. Full article

Although membrane technology has been widely applied in water treatment, membrane fouling is an inevitable issue that has largely limited its application. Benefiting from the advantages of green power, easy integration and low chemical consumption, electrocatalytic membrane (ECM) technology received attention, using it to enable electrically driven self-cleaning performance recently, making it highly desirable for sustainable fouling control. In this work, we comprehensively summarized the conventional (e.g., carbonaceous materials, metal and metal oxide) and emerging (e.g., metal–organic framework and MXene) materials for the fabrication of an ECM. Then the fabrication methods and operating modes of an ECM were emphasized. Afterwards, the application of different ECM materials in membrane fouling control was highlighted and the corresponding mechanism was revealed. Based on existing research findings, we proposed the challenges and future prospects of ECM materials for practical application. This study provides enlightening knowledge into the development of ECM materials for sustainable fouling control. Full article

Membrane technologies are used in the production of potable water and the treatment of wastewater in the military forces, providing the highest level of contaminant removal at an energy-efficient cost. This review examines the integration and application of membrane technologies, including reverse osmosis, nanofiltration, ultrafiltration, electrodialysis and advanced hybrid systems, in the treatment of wastewater generated at military bases, naval vessels and submarines. Special emphasis is placed on purification technologies for chemically, biologically and radiologically contaminated wastewater, as well as on the recycling and treatment of wastewater streams by mobile systems used in military applications. Given the specific requirements of complex military infrastructures, particularly in terms of energy efficiency, unit self-sufficiency and reduced dependence on logistical supply chains, this work analyses the latest advances in membrane technologies. Innovations such as nanographene membranes, biomimetic membranes, antifouling membrane systems and hybrid configurations of forward osmosis/reverse osmosis and electrodialysis/reverse electrodialysis offer unique potential for implementation in modular and mobile water treatment systems. In addition, the integration and operational use of these advanced technologies serve as a foundation for the development of autonomous military water supply strategies tailored to extreme operational conditions. The continued advancement and optimization of membrane technologies in military contexts is expected to significantly impact operational sustainability while minimizing environmental impact. Full article

Steroid hormones are micropollutants that contaminate water worldwide and have significant impacts on human health and the environment, even at very low concentrations. The aim of this article is to provide an overview of technologies for the removal of endocrine-disrupting compounds with a focus on oestrogens (estrone E1, 17β-oestradiol E2, estriol E3), the synthetic oestrogen (17α-ethinylestradiol EE2 and bisphenol A BPA), and pharmaceuticals found in wastewater. Hormonal and pharmaceutical contaminants are mostly persistent organic compounds that cannot be easily removed using conventional wastewater treatment processes. For this reason, researchers have tried to develop more efficient tertiary wastewater treatment technologies to reduce micropollutant concentrations in wastewater. This review covers the following processes: Advanced oxidation, nanofiltration, ultrasound, electro-Fenton processes, electrolysis, adsorption, ozonation, photolysis, photocatalysis, ultrafiltration, and electrocoagulation. Attention was paid to the effectiveness of the processes in terms of eliminating hormones and pharmaceuticals from wastewater, as well as on economic and environmental aspects. The combination of different processes can be a promising treatment scheme for retaining and degrading hormonal and pharmaceutical compounds from wastewater. With hybrid technologies, the advantages of the methods are combined to maximise the removal of pollutants. However, optimal methods of wastewater treatment depend on the quality and quantity of the wastewater, as well as the residual hormonal and pharmaceutical compounds and their hazardous effects. Full article

Per- and polyfluoroalkyl substances (PFASs), used since the 1940s, are persistent and carcinogenic pollutants. Water is a major exposure route; effective removal is essential. While nanofiltration (NF) and reverse osmosis (RO) are effective but costly, ultrafiltration (UF) membranes offer advantages such as lower cost and higher flux, but their relatively large pore size makes them ineffective for PFAS compounds like perfluorooctane sulfonic acid (PFOS) and perfluorooctanoic acid (PFOA). Since PFAS removal depends on both pore size and surface properties, this study investigates the effect of polyelectrolyte multilayer coatings using poly(allylamine hydrochloride) (PAH) and poly(acrylic acid) (PAA) on the zeta potential of UF membranes. Pristine UF membranes showed limited performance (UP150: ~2% for both PFOS and PFOA; UP020: 34.4% PFOS, 24.1% PFOA), while coating significantly enhanced removal (coated UP150: 45.3% PFOS, 43.4% PFOA; coated UP020: 77.8% PFOS, 73.3% PFOA). The modified UF membranes achieved PFAS removal efficiencies significantly closer to NF membranes, though still below those of RO (e.g., BW30XLE: up to 91.0% PFOS, 88.3% PFOA; NP030: up to 81.0% PFOS, 79.3% PFOA). Findings emphasize the importance of membrane surface charge and suggest that modified UF membranes offer a promising, low-cost alternative for PFAS removal under low-pressure conditions. Full article

Precise separation and antifouling capabilities are critical for the application of membrane separation technology. In this work, we developed a multiplayer layer-by-layer assembly strategy to sequentially deposit tannic acid (TA) and lysozyme (Lys) onto polyethersulfone/iron (PES/Fe) ultrafiltration membrane substrates, enabling the simple and efficient fabrication of a biofouling-resistant loose nanofiltration (LNF) membrane with superior dye/salt separation performance. This approach fully leverages the multifunctionality of TA by exploiting its coordination with Fe³⁺ and non-covalent interactions with Lys. The obtained PES/Fe-TA-Lys LNF membrane exhibits a pure water flux of 57.5 L·m⁻²·h⁻¹, along with exceptional dye rejection rates (98.3% for Congo Red (CR), 99.2% for Methyl Blue (MB), 98.4% for Eriochrome Black T (EBT), and 67.6% for Acid Orange 74 (AO74)) while maintaining minimal salt retention (8.2% for Na₂SO₄, 4.3% for MgSO₄, 3.5% for NaCl, and 2.4% for MgCl₂). The PES/Fe-TA-Lys LNF membrane also displays outstanding antifouling performance against bovine serum albumin (BSA), humic acid (HA), and CR, along with strong biofouling resistance against Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) via synergistic anti-adhesion and biofilm inhibiting effects. This work presents a novel and scalable approach to fabricating biofouling-resistant LNF membranes, offering great potential for dye/salt separation in textile wastewater treatment. Full article

The acid whey derived during the production of Greek yoghurt, i.e., yoghurt acid whey (YAW), is considered as environmental pollutant due to its low pH and high lactose content. YAW may be obtained by centrifugation or ultrafiltration or filtration through cloth bags (traditional method) of the initial yoghurt, methods that could affect its composition. In the last years, efforts have been made to improve its composition using membrane technology. In the present work, the composition of 35 different YAW samples from Greek Yoghurt dairies was studied. The YAW samples were grouped according to the way of production and the kind of milk in the case of the traditional method. The results showed that both the kind of milk and the way of yoghurt staining affected its composition. Ovine YAW derived from traditional straining was richer in lactic acid and calcium than bovine YAW. Moreover, the composition of bovine YAW varied among the different ways of straining, and this affected its behaviour during membrane processing. Nanofiltration of three representative bovine YAW samples and one ovine YAW sample at their natural pH, i.e., pH 4.5, and at 25 °C removed the lactic acid at a range from 40 to 55%, and the monovalent cations > 60% and retained lactose and galactose at percentages > 95% and 80% respectively. Full article

Mining discharge, namely acid mine drainage (AMD), is a significant environmental issue due to mining activities and site-specific factors. These pose challenges in choosing and executing suitable treatment procedures that are both sustainable and effective. Ceramic membranes, with their durability, long lifespan, and ease of maintenance, are increasingly used in industrial wastewater treatment due to their superior features. This review provides an overview of current remediation techniques for mining effluents, focusing on the use of ceramic membrane technology. It examines pressure-driven ceramic membrane systems like microfiltration, ultrafiltration, and nanofiltration, as well as the potential of vacuum membrane distillation for mine drainage treatment. Research on ceramic membranes in the mining sector is limited due to challenges such as complex effluent composition, low membrane packing density, and poor ion separation efficiency. To assess their effectiveness, this review also considers studies conducted on simulated water. Future research should focus on enhancing capital costs, developing more effective membrane configurations, modifying membrane outer layers, evaluating the long-term stability of the membrane performance, and exploring water recycling during mineral processing. Full article

Micro- and nanoplastics (NPs) cannot be completely removed from water/wastewater in conventional wastewater treatment plants (WWTPs) and drinking water treatment plants (DWTPs). According to the literature analysis, membrane processes, one of the advanced treatment technologies, are the most effective and promising technologies for the removal of microplastics (MPs) from water and wastewater. In this article, firstly, the properties of MPs commonly found in water and wastewater treatment and their removal efficiencies are briefly reviewed. In addition, research on the use of microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), reverse osmosis (RO), and membrane bioreactors (MBR) for the remediation of MPs and NPs from water/wastewater is reviewed, and the advantages/disadvantages of each removal method are discussed. Membrane filtration is also compared with other methods used to remove MPs. Furthermore, the problem of membrane fouling by MPs during filtration and the potential for MPs to be released from the polymeric membrane structure are discussed. Finally, based on the literature survey, the current status and gaps in research on MPs removal by membrane technologies are identified, and recommendations for further research are made. Full article

The intense consumption of polymeric materials combined with poor waste management results in the dissemination of their fragments in the environment as micro- and nanoplastics. They are easily dispersed in stormwater, wastewater, and landfill leachate and carried towards rivers, lakes, and oceans, causing their contamination. In aqueous matrices, the use of membrane separation processes has stood out for the efficiency of removing these particulate contaminants, achieving removals of up to 100%. For this review article, we researched the removal of microplastics and nanoplastics by membrane processes whose driving force is the pressure gradient. The analysis focuses on the challenges found in the operation of microfiltration, ultrafiltration, nanofiltration, and reverse-osmosis systems, as well as on the innovations applied to the membranes, with comparisons of treatment systems and the peculiarities of each system and each aqueous matrix. We also point out weaknesses and opportunities for future studies so that these techniques, known to be capable of removing many other contaminants of emerging concern, can subsequently be widely applied in the removal of micro- and nanoplastics. Full article

This study investigated the properties of a novel polymeric membrane based on cellulose acetate, polyethylene glycol/poly(styrene)-b-poly(4-vinylpyridine), and embedded with TiO₂ nanoparticles (CA/PEG/PS₁₅₄-b-P4VP₃₈₁/TiO₂ membrane) obtained by wet-phase inversion method. The TiO₂ nanoparticles fabricated by a hydrothermal method were characterized by XRD, SEM, EDX, and UV-Vis analyses to determine the purity, morphology, and optical band gap energy. The prepared polymeric membranes with and without TiO₂ nanoparticles (CA/PEG/PS₁₅₄-b-P4VP₃₈₁/TiO₂ and CA/PEG/PS₁₅₄-b-P4VP₃₈₁ membranes) were characterized by FTIR, SEM, EDXS, and TGA to observe the effect of TiO₂ nanoparticles added to the polymeric membrane matrix and to analyze the chemical structure, morphology, and thermal stability of the obtained polymeric membranes. The contact angle, SFE, water retention, and porosity were also determined. The results showed that adding the TiO₂ nanoparticles into the polymeric membrane (CA/PEG/PS₁₅₄-b-P4VP₃₈₁/TiO₂) significantly reduced the pore size and the water contact angle, increasing the water retention and the porosity. The lower value of the water contact angle of 15.57 ± 0.45° for the CA/PEG/PS₁₅₄-b-P4VP₃₈₁/TiO₂ membrane indicates a pronounced hydrophilic character. The investigations performed showed that the CA/PEG/PS₁₅₄-b-P4VP₃₈₁/TiO₂ membrane presents excellent properties and can be a promising material for water and waste-water treatment through membrane processes (e.g., electrodialysis, ultrafiltration, nanofiltration, reverse osmosis) in the future. Full article

This review focuses on the use of membrane techniques to recover nutrients from the liquid fraction of digestate (LFD) and emphasizes their role in promoting the principles of the circular economy. A range of membrane separation processes are examined, including microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), reverse osmosis (RO), forward osmosis (FO), membrane distillation (MD) and new tools and techniques such as membrane contactors (MCs) with gas-permeable membranes (GPMs) and electrodialysis (ED). Key aspects that are analyzed include the nutrient concentration efficiency, integration with biological processes and strategies to mitigate challenges such as fouling, high energy requirements and scalability. In addition, innovative hybrid systems and pretreatment techniques are examined for their potential to improve the recovery rates and sustainability. The review also addresses the economic and technical barriers to the full-scale application of these technologies and identifies future research directions, such as improving the membrane materials and reducing the energy consumption. The comprehensive assessment of these processes highlights their contribution to sustainable nutrient management and bio-based fertilizer production. Full article

The efficiency of integrated treatment systems for wastewater generated during the washing of disinfectant production lines was investigated. The high organic load (COD 2000 mg/L, TOC 850 mg/L) and 300 mg/L of toxic benzalkonium chloride (BAC) make wastewater an environmental hazard that requires advanced treatment. Initial tests on model BAC solutions (in concentrations corresponding to those found in wastewater), using nanofiltration and ultrafiltration membranes, resulted in up to 70% retention of BAC. To enhance purification, ion exchange and adsorption were introduced as post-membrane treatment steps. In the second part of the investigation, membrane modules characterized by the best separation properties were integrated together with macroporous cation-exchange resin and activated carbon into the purification system to treat wastewater. The research carried out showed that the purification of multicomponent wastewater is a complex task. Significantly lower BAC removal (30%) was achieved in membrane processes compared to the model solutions treatment. In integrated systems, the BAC concentration was reduced to 100 mg/L, TOC to 200 mg/L, and COD to 120 mg/L. Full article

The textile district of Prato (Italy) has developed a wastewater recycling system of considerable scale. The reclaimed wastewater is characterized by high levels of hardness (32 °F on average), which precludes its direct reuse in numerous wet textile processes (e.g., textile dyeing). Consequently, these companies utilize ion exchange resins for water softening. However, the regeneration of the resins results in an increased concentration of chlorides in the reclaimed wastewater that exceeds the limit set by Italian regulations for the reuse of water for irrigation purposes. The objective of this study is to investigate the potential of membrane filtration as an alternative method for removing hardness from water. Therefore, an industrial-scale ultrafiltration-nanofiltration (UF-NF) pilot plant was installed to test the rejection of hardness from the reclaimed wastewater. The experiment employed two types of NF membranes and three permeate fluxes (27, 35, and 38 L·m⁻²·h⁻¹) for testing. The results demonstrated that the system could remove hardness with efficiencies exceeding 98% under all conditions tested. The experimental findings indicate that the UF-NF system has the potential to be employed as a post-treatment step to render the reclaimed wastewater suitable for all textile finishing processes and to expand the scope for reuse. Full article