Search Results (1,066)

Ripple currents on the direct current (DC) bus in variable frequency drive (VFD) systems originate from motor load current fluctuations and the high-frequency switching of power devices. The resulting Joule heating within the DC-link capacitors is a primary driver of lifespan degradation. To address the lack of systematic models for multi-phase H-bridge inverters and the over-design caused by empirical methods, this paper proposes a novel analytical method that incorporates the 2kπ/N phase difference of parallel units for precise ripple current quantification. First, a dynamic DC-link capacitor model is established based on a single-phase H-bridge inverter, and the expressions for the instantaneous, average, and root mean square (RMS) input currents are derived. Furthermore, by introducing the 2kπ/N phase difference (where k = 0, 1, …, N − 1) among N parallel H-bridge units, a universal analytical expression for the RMS input current and its harmonic spectrum in a multi-phase system is obtained. The analysis reveals that ripple current harmonics concentrate at 2m × f_sw (where m is a positive integer and f_sw is switching frequency) and their sidebands (2m × f_sw ± f_o, f_o is output fundamental frequency), and the coupling influence of modulation index and power factor angle on ripple amplitude is quantitatively characterized. A 12 × 160 kW twelve-phase H-bridge inverter is taken as a case study, and MATLAB (v2023b) simulations and hardware experiments demonstrate that the theoretical calculations are in close agreement with the simulated and measured results, with the errors of input current harmonic amplitudes all below 5%. Compared with traditional empirical design, the proposed method reduces the capacitor volume and cost by approximately 15–20% while ensuring system reliability. This method is directly extensible to other multi-phase inverter topologies, providing a theoretical foundation for the accurate selection of DC-link capacitors. Full article

Winter thermal comfort in university classrooms in China’s Hot Summer and Cold Winter (HSCW) regions remains problematic due to mismatches between institutional heating setpoints and students’ actual thermal preferences. To investigate students’ thermal perceptions and behavioral responses, a post-occupancy evaluation (POE) survey was conducted, followed by field measurements in a typical classroom in Chengdu under three conditions: no-heating condition, heating conditions at 20 °C and 25 °C. Indoor environmental parameters were continuously monitored, and thermal comfort was assessed using the Predicted Mean Vote (PMV) and Predicted Percentage of Dissatisfied (PPD) model. The results show that no-heating conditions were unacceptable, highlighting the necessity of heating. While the 20 °C setpoint provided partial improvement, thermal comfort was not consistently achieved throughout the day. In contrast, the 25 °C setpoint maintained near-neutral conditions during most occupied periods. In addition, a pre-heating duration of approximately 30 min was found to be essential for reducing initial thermal discomfort. Overall, the findings indicate that fixed institutional heating standards may not adequately satisfy students’ thermal needs. Adaptive heating strategies that combine appropriate setpoints with sufficient pre-heating duration are therefore recommended to balance thermal comfort and energy efficiency in university classrooms in the HSCW regions. Full article

Thermodynamics is commonly presented as a theory of macroscopic systems in stable equilibrium, built upon assumptions of extensivity and scaling with system size. In this paper, we present a universal formulation of the elementary foundations of thermodynamics, in which entropy and energy are defined and employed beyond equilibrium and without assuming extensivity. The formulation applies to all systems—large and small, with many or few particles—and to all states, whether equilibrium or nonequilibrium, by relying on carefully stated operational definitions and existence principles rather than macroscopic idealizations. Key thermodynamic concepts, including adiabatic availability and available energy, are developed and illustrated using the energy–entropy diagram representation of nonequilibrium states, which provides geometric insight into irreversibility and the limits of work extraction for systems of any size. A substantial part of the paper is devoted to the analysis of entropy transfer in non-work interactions, leading to precise definitions of heat interactions and heat-and-diffusion interactions of central importance in mesoscopic continuum theories of nonequilibrium behavior in simple and complex solids and fluids. As a direct consequence of this analysis, Clausius inequalities and the Clausius statement of the second law are derived in forms explicitly extended to nonequilibrium processes. The resulting framework presents thermodynamics as a universal theory whose concepts apply uniformly to all systems, large and small, and provides a coherent foundation for both teaching and modern applications. Full article

Load forecasting for Integrated Energy Systems (IESs) is critical to enabling multi-energy coordinated optimization and low-carbon scheduling. Facing multi-load types and multi-site high-dimensional heterogeneous data, there remains a global learning challenge stemming from insufficient representation of spatiotemporal coupling features. In response to the multi-source heterogeneous characteristics of IES loads, this paper designs a Spatiotemporal Topology Encoder that maps load data into a tensorized multi-energy spatiotemporal topological representation via fuzzy classification and multi-scale ranking. In parallel, we construct a MultiScale Hybrid Convolver to extract multi-scale, multi-level global spatiotemporal features of multi-energy load representations. We further develop a Temporal Segmentation Transformer and a Steady-State Exponentially Gated Memory Unit, and design a jointly optimized forecasting model that enforces global dynamic correlations and local, steady-state preservation. Altogether, we propose a multi-scale spatiotemporal fusion and steady-state memory-driven load forecasting method for integrated energy systems (MSTF-SMDN). Extensive experiments on a public real-world dataset from Arizona State University demonstrate the superiority of the proposed approach: compared to the strongest baseline, MSTF-SMDN reduces cooling load RMSE by 16.09%, heating load RMSE by 12.97%, and electric load RMSE by 6.14%, while achieving R² values of 0.99435, 0.98701, and 0.96722, respectively, confirming its feasibility, efficiency, and promising potential for multi-energy load forecasting in IES. Full article

In ground-source heat-pump (GSHP) systems equipped with a single U-tube borehole heat exchanger (BHE), the heat-carrier fluid in the return leg may release heat to the surrounding ground in the shallow part of the borehole. From a fluid energy balance perspective, this is an exothermic process; however, it is detrimental during heating operation: It lowers the effective source temperature available to the heat pump and therefore degrades the overall coefficient of performance (COP). This study proposes a measurement-driven procedure to determine the exothermic transition depth $z_{\uparrow }^{*}$ from temperature profiles recorded at multiple depths along the ascending (return) pipe. The borehole is discretized into axial segments and, assuming a constant mass flow rate, the linear heat-exchange rate is estimated from the segment-wise enthalpy change. Time integration yields the segment-wise net energy exchange $Q_{\uparrow ,i}$, which is then classified as exothermic or endothermic using an uncertainty-based threshold derived from the standard uncertainty of the temperature sensors. The exothermic transition depth $z_{\uparrow }^{*}$ is defined as the first statistically stable sign change in the integrated segment energy (from exothermic to endothermic) and is obtained by linear interpolation between adjacent segment centres. By summing the exothermic energy exchange and the corresponding average loss power, an equivalent change in source-side outlet temperature $∆T_{out}$ is estimated and interpreted in terms of COP impact using a Carnot-scaled surrogate model. For two representative operating conditions, $z_{\uparrow }^{*}$ was found at $31.17 \mathrm{m}$ and $24.01 \mathrm{m}$, respectively, while the average exothermic loss power remained approximately 0.48 kW. The estimated $∆T_{out}$ ranged from $0.52$ to $0.75 \mathrm{K}$, corresponding to a diagnostic COP improvement if this parasitic exothermic exchange could be mitigated. The present results should therefore be interpreted as a case study-based demonstration of the method on one instrumented borehole rather than as a universal quantitative prediction for other sites or borehole fields. Full article

Ice clouds play a significant role in the Earth’s radiation balance due to their unique microphysical and radiative properties, which vary with formation mechanisms and regions and influence the local energy budget. In this study, six years of Ka-band Zenith Radar (KAZR) observations from the Semi-Arid Climate and Environment Observatory of Lanzhou University (SACOL) and the Southern Great Plains (SGP) sites, combined with the Fu–Liou radiative transfer model, were used to examine the macrophysical and microphysical properties of ice clouds, their radiative effects, and contributions to the surface energy budget. The results show that the frequency of ice cloud occurrence at SACOL is 40%, significantly higher than the 27% observed at SGP. At both sites, ice cloud altitudes exhibit an increasing trend in the context of recent warming, with a more pronounced increase at SGP. Seasonal variations are evident, with spring characterized by relatively thick and widespread ice clouds, while summer is dominated by high-altitude, optically thin clouds. Ice cloud occurrence peaks at night and decreases during the day at both sites; however, cloud diurnal variations in summer are much greater at SGP than at SACOL. Radiative analysis indicates that longwave radiation-induced warming dominates ice cloud radiative forcing. Net radiative forcing at the top of the atmosphere is 6.08 W/m² at SACOL and 3.06 W/m² at SGP, contributing to atmospheric heating within and beneath cloud layers. At the surface, sensible heat dominates the energy budget at SACOL (over 63%) due to its arid climate, whereas latent heat dominates at SGP (about 67%) because of abundant moisture; and ice clouds have the greatest impact in winter, reducing surface net radiation by 29% at SACOL and 26% at SGP, producing a cooling effect. Full article

At temperatures higher than 5 °C in the cooling chambers of refrigeration systems, bacteria multiply rapidly on fresh fishes, thereby leading to an increased risk of foodborne diseases. Maintaining the storage temperature within the recommended bounds of 0 °C and 5 °C is needed to maintain food safety and quality. This study presents model predictive control of a data-driven medium-temperature cold storage system using subspace system identification techniques. The identified linear model presents a holistic view of the whole system, with each subsystem cohesively linked together. The data-driven model was developed from synthetic data derived from a high-fidelity simulation benchmark model of a supermarket refrigeration system from Aalborg University, Denmark. The benchmark model consists of a medium-temperature closed display case, the suction manifold, and the compressor rack. The data of the expansion valve, suction pressure, compressor capacity, heat transfer rate, and ambient temperature were taken as inputs, while the data of the air and goods temperatures were taken as outputs based on expert knowledge. A linear model predictive controller was designed to control the temperature outputs of the identified linear model, and the outputs were compared with the proportional–integral dead band control used in the benchmark. Simulation results for 24 h showed that the model predictive controller was able to achieve an air temperature and a goods temperature within the recommended temperature range of 0 °C and 5 °C that guarantees safe storage of fresh fishes. These results imply that a reduced-order model of a commercial refrigeration system that is robust, reliable, and stable can be developed and controlled to achieve the goal of food safety, thereby guaranteeing food security and reducing costs. Full article

Climate chambers enable repeatable indoor boundary conditions and are increasingly used to study multi-domain IEQ. However, thermal comfort and IAQ are still often evaluated separately, limiting evidence on their coupled behavior and potential trade-offs under different ventilation and air-cleaning strategies. The present study was carried out in the climate chamber located in the laboratory facilities of the University of Western Macedonia to quantify thermal comfort and IAQ simultaneously across different experimental scenarios that vary ventilation mode, heating operation, and occupancy. The results show a correlation between subjective and objective measurements, with the comfort temperature varying around 22.2 °C, as estimated by the Griffiths model, while ventilation mainly affects the stability of the thermal environment. CO₂ levels scaled with occupancy and ventilation rate, while PM removal was strongly strategy-dependent: after a controlled smoke event, mechanical ventilation plus air purification achieved the fastest decay and recovery toward near-background concentrations. Overall, this work represents a first step toward coupled IEQ research by jointly quantifying thermal comfort and IAQ in a climate chamber, enabling systematic comparison of ventilation strategies in terms of both perceived comfort and pollutant exposure. Full article

Short auditory cues in enclosed built environments (such as elevator calls, access control, navigation, and heating, ventilation, and air conditioning (HVAC) notifications) influence not only usability but also stress and perceptions of well-being in daily indoor life. However, acoustic research remains largely focused on physical properties, and the psychophysiological impact of such short auditory cues remains under-quantified. To address this gap, a neuroscience-based evaluation approach, the Acoustic User Experience and Emotion (AUEX) model, is proposed. This model integrates functional near-infrared spectroscopy (fNIRS), electrodermal activity (EDA), and the User Experience Questionnaire (UEQ). With 33 in-cabin prompt sounds as a controlled typology of short auditory cues in an enclosed setting, we set up a simulated interaction experiment with 20 participants in a driving simulator vehicle cabin to investigate the relationship between acoustic properties and cognitive load, arousal, and user experience. The results show that timbre is the key factor, which was correlated positively with overall UX (r = 0.414) and negatively with prefrontal ΔHbO (CH3: r = −0.368; l-DLPFC: r = −0.449), indicating a decrease in cognitive load and a relaxed affective state. Conversely, high-frequency signals improved pragmatic quality but increased physiological arousal, which negatively affected hedonic assessment. To facilitate the translation of evaluation results into practice, we also completed a design phase that converted the AUEX results into scenario-based parameter targets and prototype designs for functional, warning, and brand/affective cues, illustrating how evidence-based relationships can be translated into design-ready outputs for enclosed built environments. These results confirm the AUEX approach as a transferable method for designing short auditory cues for well-being and provide parameter-level implications for therapeutic and human-centered sound design in smart buildings, intelligent vehicles, and other enclosed built environments. Overall, the AUEX approach provides a transferable evaluation-to-design workflow for short auditory cues in enclosed interactive contexts; however, direct generalization from a single controlled vehicle cabin setting to real-world building environments should be validated through future field studies. Accordingly, the present findings are positioned as evidence from a controlled enclosed case rather than universal conclusions for all enclosed spaces. Full article

Traditional field-based ecological surveys are inefficient in mountainous regions with steep slopes and deep valleys, highlighting the need for new quantitative remote sensing–based approaches. To account for complex terrain, four representative topographic factors (slope, relief, dissection, curvature) were selected via Digital Elevation Model (DEM) analysis to develop a Terrain Complexity Index (TCI), replacing the dryness component in the Remote Sensing Ecological Index (RSEI). Combined with greenness, wetness, and heat factors from Landsat 8, TCI was integrated using principal component analysis to form a Terrain-Adjusted RSEI (TARSEI), extending ecological assessment from two to three dimensions. In a mountainous case study in Huzhou City, Zhejiang, China, TARSEI showed a marked 34.2-percentage-point improvement over the original RSEI. Its high-value areas captured 82.3% of ecotourism points of interest, versus 48.1% for RSEI, demonstrating its enhanced accuracy for terrain-specific analysis. TARSEI further identified 28 new ecotourism resource clusters totaling 520.1 km² (8.9% of the city area), with a 98.5% overlap with high TARSEI zones. These results confirmed TARSEI’s effectiveness and provided robust scientific support for sustainable ecotourism development and spatial planning. With its high accuracy, stability, and universality, TARSEI is a promising and transferable tool for ecotourism resource assessment and spatial planning and management in complex terrain regions. Full article

Urban environments face increasing thermal stress from climate change and the Urban Heat Island effect, with significant implications for livability, public health, and energy sustainability. Outdoor thermal comfort is defined as the state in which conditions are perceived as acceptable, depends on interactions among meteorological, morphological, physiological, and behavioral factors. This review synthesizes the application of machine learning (ML) to outdoor thermal comfort assessment into a practice-oriented taxonomy. Research spans diverse climates and urban forms, using inputs across environmental and human domains. Supervised learning dominates. Regression approaches (linear regression, support vector regression, random forest, gradient boosting) and classification algorithms (decision trees, support vector machines, K-nearest neighbors, Naïve Bayes, random forest classifiers) are widely used to predict thermal indices such as the Physiological Equivalent Temperature and Universal Thermal Climate Index, or to classify subjective responses including thermal sensation, comfort, and acceptability. Unsupervised learning (clustering, principal component analysis) supports identification of microclimatic zones and perceptual clusters, while deep learning (multilayer perceptrons, convolutional and recurrent neural networks, generative adversarial networks) achieves superior accuracy for complex, high-dimensional, and spatiotemporal data. Algorithms such as random forests, support vector machines, and gradient boosting consistently show strong performance for both indices and subjective responses when integrating multi-domain inputs. Semi-supervised and reinforcement learning remain underexplored but offer promise for leveraging large-scale sensor data and enabling adaptive, real-time comfort management. The review concludes with a roadmap emphasizing explainable artificial intelligence, scalable surrogate modeling, and integration with simulation-based optimization and parametric design tools. Full article

Large-diameter axial-flow fans are predominantly used for cooling purposes, such as in air-cooled heat exchangers. Since it is difficult to experimentally test large-scale fans in the controlled environments provided by fan test facilities, smaller scaled-down versions of the fans are tested instead. Scaling laws, also called affinity laws, are then used to determine the performance characteristics of the large-scale fan. The size difference between the two scaled fans means that it is not possible to match their Reynolds numbers when testing with the same test fluid. A comparison is conducted using experimental results and four numerical models for two different fans, which are scaled to different fan sizes: 0.63 m, 1.542 m, 3.658 m and 7.315 m, to determine the effect of Reynolds number on the performance characteristics of an axial-flow fan. The numerical geometries are based on the M- and B2a-fans, and are tested in the A-type experimental setup fan test facility at Stellenbosch University, which is used to obtain the experimental results. It was found that the numerical approach discussed within this paper, namely a Reynolds-Averaged Navier–Stokes (RANS) approach, can predict the performance of multiple fan sizes without relying on turbomachinery or blade-specific empirical correlations. This approach accelerates the evaluation of fan performance while enabling the parameterization of fan configurations. Full article

Achieving meaningful reductions in residential heating demand requires design strategies that can respond to climate-specific solar availability and envelope performance. Although passive solar principles are well established, their effectiveness remains highly context-dependent, and simplified prescriptive approaches may not capture interactions across different climates. This study presents an AI-guided evolutionary optimization framework for passive solar residential design, focusing exclusively on the reduction in annual space heating demand under standardized assumptions. A standardized single-story residential prototype is simulated across three climatic contexts: hot–dry (Riyadh), temperate (Barcelona), and cold (Toronto). Dynamic building performance simulations are conducted using EnergyPlus, coupled with DesignBuilder’s built-in Non-Dominated Sorting Genetic Algorithm II (NSGA-II) evolutionary optimization engine. Envelope-related variables, including the window-to-wall ratio, orientation, glazing configuration, and thermal mass, are optimized with a single objective: minimizing the annual heating load under idealized heating conditions. The results demonstrate substantial climate-dependent reductions in heating demand. In Toronto, the annual heating demand is reduced from approximately 16,900 kWh to 9600 kWh (≈43%). In Barcelona, a reduction from approximately 5650 kWh to 1990 kWh (≈65%) is achieved, while in Riyadh, heating demand is reduced from approximately 990 kWh to 39 kWh (>95%). The optimized solutions reveal distinct climate-specific design logic rather than universal passive rules. The results demonstrate that evolutionary optimization can support early-stage envelope design by revealing climate-specific heating strategies under clearly defined and comparable assumptions. Full article

In this article, we extend the recently proposed theoretical framework for nonequilibrium magnetothermal effects induced by a sudden magnetic field quenching to anisotropic 3d-metal complexes with arbitrary spins. The formalism is applicable not only to the case of complete magnetic field switching off, but also to the case of partial field quenching. A simple and universal semiquantitative rule is formulated, which allows for the prediction of the sign of a thermal effect (that means heat absorption or heat release) from the magnetic field dependencies of the spin energy levels. In many specific cases, this rule can be used to predict the sign of the magnetothermal effect prior to calculations, based on an analysis of the field dependencies of the spin levels of the complexes under study. According to this rule, each excited state contributes to cooling or heating depending on whether it becomes destabilized or stabilized as the field decreases. The performed numerical analysis of the specific heat release, as a function of temperature and initial and final magnetic fields for complexes with spins S = 1, 3/2, 2, and 5/2, demonstrates that systems with easy-axis magnetic anisotropy (D < 0) exhibit heat absorption in cases of complete and incomplete field quenching, with the effect being strongly enhanced in the latter case. In contrast, in complexes with easy-plane-type anisotropy (D > 0), the sign of the thermal effect is shown to be dependent on the temperature, the initial and final values of the magnetic field, and also on whether the spin of the complex is integer or half-integer. These results provide clear and practical guidelines for the design of low-temperature molecular magnetic refrigerants operating in fast field-quenching regimes. Full article

This study employs high-temperature precipitation combined with heating dissolution to redistribute solute atoms near the grain boundaries of alloy 2618, regulating the width of the precipitation-free zone at the grain boundaries and the aging precipitates in their vicinity. Microscopy techniques, including high-resolution scanning electron microscopy and transmission electron microscopy, were used to observe the grain-boundary structure of the alloy. A universal electronic tensile testing machine and an impact tester were used to evaluate the mechanical properties of the alloy. The results show that solution treatment at 535 °C for 30 min, followed by high-temperature precipitation at 470 °C for 10 min and subsequent heating dissolution at 535 °C for 10 min, significantly narrowed the width of the precipitation-free zone at the grain boundaries of alloy 2618. The number of precipitated phases in the vicinity of the grain boundaries increased. Compared with the conventional solution aging treatment of alloy 2618, the tensile strength and impact toughness of the alloy subjected to high-temperature precipitation, heating dissolution, and aging increased by 5.0% and 23.7%, respectively. Thus, the synergistic effects of high-temperature precipitation and heating dissolution effectively improved the grain-boundary structure and enhanced the overall mechanical properties of alloy 2618. Full article