Editor’s Choice Articles

Electrical Impedance Myography (EIM) is a painless, noninvasive approach for assessing muscle conditions through the application of a high-frequency, low-intensity current to the muscle region of interest. However, besides muscle properties, EIM measurements vary significantly with changes in some other anatomical properties such as subcutaneous skin-fat (SF) thickness and muscle girth, as well as non-anatomical factors, such as ambient temperature, electrode shape, inter-electrode distance, etc. This study has been conducted to compare the effects of different electrode shapes in EIM experiments, and to propose an acceptable configuration that is less dependent on factors other than the cellular properties of the muscle. Initially, a finite element model with two different kinds of electrode shapes, namely, rectangular (the conventional shape) and circular (the proposed shape) was designed for a subcutaneous fat thickness ranging from 5 mm to 25 mm. The study concludes, based on the FEM study, that replacing the conventional electrodes with our proposed electrodes can decrease the variation in EIM parameters due to changes in skin-fat thickness by 31.92%. EIM experiments on human subjects with these two kinds of electrode shapes validate our finite element simulation results, and show that circular electrodes can improve EIM effectiveness significantly, irrespective of muscle shape variation. Full article

We report on a spiral structure suitable for obtaining a large optical response. We constructed a structural mechanics model of the shape of the planar spiral structure when deformed and verified the effectiveness of the model. As a verification structure, we fabricated a large-scale spiral structure that operates in the GHz band by laser processing. Based on the GHz radio wave experiments, a more uniform deformation structure exhibited a higher cross-polarization component. This result suggests that uniform deformation structures can improve circular dichroism. Since large-scale devices enable speedy prototype verification, the obtained knowledge can be exported to miniaturized-scale devices, such as MEMS terahertz metamaterials. Full article

A safety and arming device with a condition feedback function has been designed in this article to improve the intelligence and safety of ignition devices. The device achieves active control and recoverability by virtue of four groups of bistable mechanisms which consist of two electrothermal actuators to drive a semi-circular barrier and a pawl. According to a specific operation sequence, the barrier is engaged by the pawl at the safety or the arming position. The four groups of bistable mechanisms are connected in parallel, and the device detects the contact resistance generated by the engagement of the barrier and pawl by the voltage division of an external resistor to determine the parallel number of the mechanism and give feedback on the device’s condition. The pawl as a safety lock can restrain the in-plane deformation of the barrier in the safety condition to improve the safety function of the device. An igniter (a NiCr bridge foil covered with different thicknesses of Al/CuO films) and boron/potassium nitrate (B/KNO₃, BPN) are assembled on both sides of the S&A device to verify the safety of the barrier. The test results show that the S&A device with a safety lock can realize the safety and arming functions when the thickness of the Al/CuO film is set to 80 μm and 100 μm. Full article

Electrowetting Display (EWD) is a new reflective display with an outstanding performance of color video playback. However, some problems still exist and affect its performance. For instance, oil backflow, oil splitting, and charge trapping phenomena may occur during the driving process of EWDs, which would decrease its stability of multi-level grayscales. Therefore, an efficient driving waveform was proposed to solve these disadvantages. It consisted of a driving stage and a stabilizing stage. First, an exponential function waveform was used in the driving stage for driving the EWDs quickly. Then, an alternating current (AC) pulse signal waveform was used in the stabilizing stage to release the trapped positive charges of the insulating layer to improve display stability. A set of four level grayscale driving waveforms were designed by using the proposed method, and it was used in comparative experiments. The experiments showed that the proposed driving waveform could mitigate oil backflow and splitting effects. Compared to a traditional driving waveform, the luminance stability was increased by 8.9%, 5.9%, 10.9%, and 11.6% for the four level grayscales after 12 s, respectively. Full article

Currently, an urgent need in the field of wearable electronics is the development of flexible sensors that can be attached to the human body to monitor various physiological indicators and movements. In this work, we propose a method for forming an electrically conductive network of multi-walled carbon nanotubes (MWCNT) in a matrix of silicone elastomer to make stretchable sensors sensitive to mechanical strain. The electrical conductivity and sensitivity characteristics of the sensor were improved by using laser exposure, through the effect of forming strong carbon nanotube (CNT) networks. The initial electrical resistance of the sensors obtained using laser technology was ~3 kOhm (in the absence of deformation) at a low concentration of nanotubes of 3 wt% in composition. For comparison, in a similar manufacturing process, but without laser exposure, the active material had significantly higher values of electrical resistance, which was ~19 kOhm in this case. The laser-fabricated sensors have a high tensile sensitivity (gauge factor ~10), linearity of >0.97, a low hysteresis of 2.4%, tensile strength of 963 kPa, and a fast strain response of 1 ms. The low Young’s modulus values of ~47 kPa and the high electrical and sensitivity characteristics of the sensors made it possible to fabricate a smart gesture recognition sensor system based on them, with a recognition accuracy of ~94%. Data reading and visualization were performed using the developed electronic unit based on the ATXMEGA8E5-AU microcontroller and software. The obtained results open great prospects for the application of flexible CNT sensors in intelligent wearable devices (IWDs) for medical and industrial applications. Full article

A novel monocrystalline AlN interfacial layer formation method is proposed to improve the device performance of the fully recessed-gate Al₂O₃/AlN/GaN Metal-Insulator-Semiconductor High Electron Mobility Transistors (MIS-HEMTs), which is achieved by plasma-enhanced atomic layer deposition (PEALD) and in situ N₂ plasma annealing (NPA). Compared with the traditional RTA method, the NPA process not only avoids the device damage caused by high temperatures but also obtains a high-quality AlN monocrystalline film that avoids natural oxidation by in situ growth. As a contrast with the conventional PELAD amorphous AlN, C-V results indicated a significantly lower interface density of states (D_it) in a MIS C-V characterization, which could be attributed to the polarization effect induced by the AlN crystal from the X-ray Diffraction (XRD) and Transmission Electron Microscope (TEM) characterizations. The proposed method could reduce the subthreshold swing, and the Al₂O₃/AlN/GaN MIS-HEMTs were significantly enhanced with ~38% lower on-resistance at V_g = 10 V. What is more, in situ NPA provides a more stable threshold voltage (V_th) after a long gate stress time, and ΔV_th is inhibited by about 40 mV under V_g,stress = 10 V for 1000 s, showing great potential for improving Al₂O₃/AlN/GaN MIS-HEMT gate reliability. Full article

The study of wearable systems based on surface electromyography (sEMG) signals has attracted widespread attention and plays an important role in human–computer interaction, physiological state monitoring, and other fields. Traditional sEMG signal acquisition systems are primarily targeted at body parts that are not in line with daily wearing habits, such as the arms, legs, and face. In addition, some systems rely on wired connections, which impacts their flexibility and user-friendliness. This paper presents a novel wrist-worn system with four sEMG acquisition channels and a high common-mode rejection ratio (CMRR) greater than 120 dB. The circuit has an overall gain of 2492 V/V and a bandwidth of 15~500 Hz. It is fabricated using flexible circuit technologies and is encapsulated in a soft skin-friendly silicone gel. The system acquires sEMG signals at a sampling rate of over 2000 Hz with a 16-bit resolution and transmits data to a smart device via low-power Bluetooth. Muscle fatigue detection and four-class gesture recognition experiments (accuracy greater than 95%) were conducted to validate its practicality. The system has potential applications in natural and intuitive human–computer interaction and physiological state monitoring. Full article

The giant magnetoimpedance effect of multilayered thin films under stress has great application prospects in magnetic sensing, but related studies are rarely reported. Therefore, the giant magnetoimpedance effects in multilayered thin film meanders under different stresses were thoroughly investigated. Firstly, multilayered FeNi/Cu/FeNi thin film meanders with the same thickness were manufactured on polyimide (PI) and polyester (PET) substrates by DC magnetron sputtering and MEMS technology. The characterization of meanders was analyzed by SEM, AFM, XRD, and VSM. The results show that multilayered thin film meanders on flexible substrates also have the advantages of good density, high crystallinity, and excellent soft magnetic properties. Then, we observed the giant magnetoimpedance effect under tensile and compressive stresses. The results show that the application of longitudinal compressive stress increases the transverse anisotropy and enhances the GMI effect of multilayered thin film meanders, while the application of longitudinal tensile stress yields the opposite result. The results provide novel solutions for the fabrication of more stable and flexible giant magnetoimpedance sensors, as well as for the development of stress sensors. Full article

GaN-based micro-size light-emitting diodes (µLEDs) have a variety of attractive and distinctive advantages for display, visible-light communication (VLC), and other novel applications. The smaller size of LEDs affords them the benefits of enhanced current expansion, fewer self-heating effects, and higher current density bearing capacity. Low external quantum efficiency (EQE) resulting from non-radiative recombination and quantum confined stark effect (QCSE) is a serious barrier for application of µLEDs. In this work, the reasons for the poor EQE of µLEDs are reviewed, as are the optimization techniques for improving the EQE of µLEDs. Full article

Food quality and safety are important to protect consumers from foodborne illnesses. Currently, laboratory scale analysis, which takes several days to complete, is the main way to ensure the absence of pathogenic microorganisms in a wide range of food products. However, new methods such as PCR, ELISA, or even accelerated plate culture tests have been proposed for the rapid detection of pathogens. Lab-on-chip (LOC) devices and microfluidics are miniaturized devices that can enable faster, easier, and at the point of interest analysis. Nowadays, methods such as PCR are often coupled with microfluidics, providing new LOC devices that can replace or complement the standard methods by offering highly sensitive, fast, and on-site analysis. This review’s objective is to present an overview of recent advances in LOCs used for the identification of the most prevalent foodborne and waterborne pathogens that put consumer health at risk. In particular, the paper is organized as follows: first, we discuss the main fabrication methods of microfluidics as well as the most popular materials used, and then we present recent literature examples for LOCs used for the detection of pathogenic bacteria found in water and other food samples. In the final section, we summarize our findings and also provide our point of view on the challenges and opportunities in the field. Full article

For the first time in the world, the behavioral functions of laboratory mammals exposed to silver nanoparticles were studied with regard to age. Silver nanoparticles coated with polyvinylpyrrolidone with a size of 8.7 nm were used in the present research as a potential xenobiotic. Elder mice adapted to the xenobiotic better than the younger animals. Younger animals demonstrated more drastic anxiety than the elder ones. A hormetic effect of the xenobiotic in elder animals was observed. Thus, it is concluded that adaptive homeostasis non-linearly changes with age increase. Presumably, it may improve during the prime of life and start to decline just after a certain stage. This work demonstrates that age growth is not directly conjugated with the organism fading and pathology development. Oppositely, vitality and resistance to xenobiotics may even improve with age at least until the prime of life. Full article

This paper demonstrates a fully integrated vacuum microelectronic NOR logic gate fabricated using microfabricated polysilicon panels oriented perpendicular to the device substrate with integrated carbon nanotube (CNT) field emission cathodes. The vacuum microelectronic NOR logic gate consists of two parallel vacuum tetrodes fabricated using the polysilicon Multi-User MEMS Processes (polyMUMPs). Each tetrode of the vacuum microelectronic NOR gate demonstrated transistor-like performance but with a low transconductance of 7.6 × 10⁻⁹ S as current saturation was not achieved due to a coupling effect between the anode voltage and cathode current. With both tetrodes working in parallel, the NOR logic capabilities were demonstrated. However, the device exhibited asymmetric performance due to differences in the CNT emitter performance in each tetrode. Because vacuum microelectronic devices are attractive for use in high radiation environments, to test the radiation survivability of this device platform, we demonstrated the function of a simplified diode device structure during exposure to gamma radiation at a rate of 45.6 rad(Si)/second. These devices represent a proof-of-concept for a platform that can be used to build intricate vacuum microelectronic logic devices for use in high-radiation environments. Full article

The rational design of superhydrophilic materials with a controllable structure is a critical component in various applications, including solar steam generation, liquid spontaneous transport, etc. The arbitrary manipulation of the 2D, 3D, and hierarchical structures of superhydrophilic substrates is highly desirable for smart liquid manipulation in both research and application fields. To design versatile superhydrophilic interfaces with various structures, here we introduce a hydrophilic plasticene that possesses high flexibility, deformability, water absorption, and crosslinking capabilities. Through a pattern-pressing process with a specific template, 2D prior fast spreading of liquids at speeds up to 600 mm/s was achieved on the superhydrophilic surface with designed channels. Additionally, 3D superhydrophilic structures can be facilely designed by combining the hydrophilic plasticene with a 3D-printed template. The assembly of 3D superhydrophilic microstructure arrays were explored, providing a promising route to facilitate the continuous and spontaneous liquid transport. The further modification of superhydrophilic 3D structures with pyrrole can promote the applications of solar steam generation. The optimal evaporation rate of an as-prepared superhydrophilic evaporator reached ~1.60 kg·m⁻²·h⁻¹ with a conversion efficiency of approximately 92.96%. Overall, we envision that the hydrophilic plasticene should satisfy a wide range of requirements for superhydrophilic structures and update our understanding of superhydrophilic materials in both fabrication and application. Full article

The Growing demands for humidity detection in commercial and industrial applications led to the rapid development of humidity sensors based on different techniques. Surface acoustic wave (SAW) technology is one of these methods that has been found to provide a powerful platform for humidity sensing owing to its intrinsic features, including small size, high sensitivity, and simple operational mechanism. Similar to other techniques, the principle of humidity sensing in SAW devices is also realized by an overlaid sensitive film, which serves as the core element whose interaction with water molecules is responsible for overall performance. Therefore, most researchers are focused on exploring different sensing materials to achieve optimum performance characteristics. This article reviews sensing materials used to develop SAW humidity sensors and their responses based on theoretical aspects and experimental outcomes. Herein the influence of overlaid sensing film on the performance parameters of the SAW device, such as quality factor, signal amplitude, insertion loss, etc., is also highlighted. Lastly, a recommendation to minimize the significant change in device characteristics is presented, which we believe will be a good step for the future development of SAW humidity sensors. Full article

Biological testing on the International Space Station (ISS) is necessary in order to monitor the microbial burden and identify risks to crew health. With support from a NASA Phase I Small Business Innovative Research contract, we have developed a compact prototype of a microgravity-compatible, automated versatile sample preparation platform (VSPP). The VSPP was built by modifying entry-level 3D printers that cost USD 200–USD 800. In addition, 3D printing was also used to prototype microgravity-compatible reagent wells and cartridges. The VSPP’s primary function would enable NASA to rapidly identify microorganisms that could affect crew safety. It has the potential to process samples from various sample matrices (swab, potable water, blood, urine, etc.), thus yielding high-quality nucleic acids for downstream molecular detection and identification in a closed-cartridge system. When fully developed and validated in microgravity environments, this highly automated system will allow labor-intensive and time-consuming processes to be carried out via a turnkey, closed system using prefilled cartridges and magnetic particle-based chemistries. This manuscript demonstrates that the VSPP can extract high-quality nucleic acids from urine (Zika viral RNA) and whole blood (human RNase P gene) in a ground-level laboratory setting using nucleic acid-binding magnetic particles. The viral RNA detection data showed that the VSPP can process contrived urine samples at clinically relevant levels (as low as 50 PFU/extraction). The extraction of human DNA from eight replicate samples showed that the DNA extraction yield is highly consistent (there was a standard deviation of 0.4 threshold cycle when the extracted and purified DNA was tested via real-time polymerase chain reaction). Additionally, the VSPP underwent 2.1 s drop tower microgravity tests to determine if its components are compatible for use in microgravity. Our findings will aid future research in adapting extraction well geometry for 1 g and low g working environments operated by the VSPP. Future microgravity testing of the VSPP in the parabolic flights and in the ISS is planned. Full article

Developing small-scale continuum catheter robots with inherent soft bodies and high adaptability to different environments holds great promise for biomedical engineering applications. However, current reports indicate that these robots meet challenges when it comes to quick and flexible fabrication with simpler processing components. Herein, we report a millimeter-scale magnetic-polymer-based modular continuum catheter robot (MMCCR) that is capable of performing multifarious bending through a fast and general modular fabrication strategy. By preprogramming the magnetization directions of two types of simple magnetic units, the assembled MMCCR with three discrete magnetic sections could be transformed from a single curvature pose with a large tender angle to a multicurvature S shape in the applied magnetic field. Through static and dynamic deformation analyses for MMCCRs, high adaptability to varied confined spaces can be predicted. By employing a bronchial tree phantom, the proposed MMCCRs demonstrated their capability to adaptively access different channels, even those with challenging geometries that require large bending angles and unique S-shaped contours. The proposed MMCCRs and the fabrication strategy shine new light on the design and development of magnetic continuum robots with versatile deformation styles, which would further enrich broad potential applications in biomedical engineering. Full article

The authors present in this study the development of a novel method for creating stretchable electronics from dual-layer flex printed circuit boards (flex-PCBs) as a platform for soft robotic sensor arrays (SRSAs) for cardiac voltage mapping applications. There is a crucial need for devices that utilize multiple sensors and provide high performance signal acquisition for cardiac mapping. Previously, our group demonstrated how single-layer flex-PCB can be postprocessed to create a stretchable electronic sensing array. In this work, a detailed fabrication process for creating a dual-layer multielectrode flex-PCB SRSA is presented, along with relevant parameters to achieve optimal postprocessing with a laser cutter. The dual-layer flex-PCB SRSA’s ability to acquire electrical signals is demonstrated both in vitro as well as in vivo on a Leporine cardiac surface. These SRSAs could be extended into full-chamber cardiac mapping catheter applications. Our results show a significant contribution towards the scalable use of dual-layer flex-PCB for stretchable electronics. Full article

In recent years, Micro-Electro-Mechanical Systems (MEMS) technology has had an impressive impact in the field of acoustic transducers, allowing the development of smart, low-cost, and compact audio systems that are employed in a wide variety of highly topical applications (consumer devices, medical equipment, automotive systems, and many more). This review, besides analyzing the main integrated sound transduction principles typically exploited, surveys the current State-of-the-Art scenario, presenting the recent performance advances and trends of MEMS microphones and speakers. In addition, the interface Integrated Circuits (ICs) needed to properly read the sensed signals or, on the other hand, to drive the actuation structures are addressed with the aim of offering a complete overview of the currently adopted solutions. Full article

One of the advantages of human stem cell-derived cell-based preclinical screening is the reduction of the false negative/positive misjudgment of lead compounds for predicting their effectiveness and risks during the early stage of development. However, as the community effect of cells was neglected in the conventional single cell-based in vitro screening, the potential difference in results caused by the cell number and their spatial arrangement differences has not yet been sufficiently evaluated. Here, we have investigated the effect of the community size and spatial arrangement difference for cardiomyocyte network response against the proarrhythmic compounds from the viewpoint of in vitro cardiotoxicity. Using three different typical types of cell networks of cardiomyocytes, small cluster, large square sheet, and large closed-loop sheet were formed in shaped agarose microchambers fabricated on a multielectrode array chip simultaneously, and their responses were compared against the proarrhythmic compound, E-4031. The interspike intervals (ISIs) in large square sheets and closed-loop sheets were durable and maintained stable against E-4031 even at a high dose of 100 nM. In contrast, those in the small cluster, which fluctuated even without E-4031, acquired stable beating reflecting the antiarrhythmic efficacy of E-4031 from a 10 nM medium dose administration. The repolarization index, field potential duration (FPD), was prolonged in closed-loop sheets with 10 nM E-4031, even though small clusters and large sheets remained normal at this concentration. Moreover, FPDs of large sheets were the most durable against E-4031 among the three geometries of cardiomyocyte networks. The results showed the apparent spatial arrangement dependence on the stability of their interspike intervals, and FPD prolongation, indicating the importance of the geometry control of cell networks for representing the appropriate response of cardiomyocytes against the adequate amount of compounds for in vitro ion channel measurement. Full article

Laser microstructuring has been studied extensively in the last decades due to its versatile, contactless processing and outstanding precision and structure quality on a wide range of materials. A limitation of the approach has been identified in the utilization of high average laser powers, with scanner movement fundamentally limited by laws of inertia. In this work, we apply a nanosecond UV laser working in an intrinsic pulse-on-demand mode, ensuring maximal utilization of the fastest commercially available galvanometric scanners at scanning speeds from 0 to 20 m/s. The effects of high-frequency pulse-on-demand operation were analyzed in terms of processing speeds, ablation efficiency, resulting surface quality, repeatability, and precision of the approach. Additionally, laser pulse duration was varied in single-digit nanosecond pulse durations and applied to high throughput microstructuring. We studied the effects of scanning speed on pulse-on-demand operation, single- and multipass laser percussion drilling performance, surface structuring of sensitive materials, and ablation efficiency for pulse durations in the range of 1–4 ns. We confirmed the pulse-on-demand operation suitability for microstructuring for a range of frequencies from below 1 kHz to 1.0 MHz with 5 ns timing precision and identified the scanners as the limiting factor even at full utilization. The ablation efficiency was improved with longer pulse durations, but structure quality degraded. Full article

This paper discusses the fabrication and characterization of cyclic olefin copolymer (COC)-based pseudo-piezoelectric materials (piezoelectrets) with exceptionally high piezoelectric activity, and their potential use in sensing applications. Piezoelectrets that utilize a novel microhoneycomb structure to achieve high piezoelectric sensitivity are carefully engineered and fabricated at a low temperature using a supercritical CO₂-assisted assembly. The quasistatic piezoelectric coefficient d₃₃ of the material can reach up to 12,900 pCN⁻¹ when charged at 8000 V. The materials also exhibit excellent thermal stability. The charge build-up in the materials and the actuation behavior of the materials are also investigated. Finally, applications of these materials in pressure sensing and mapping and in wearable sensing are demonstrated. Full article

The overall survival rate of extracorporeal life support (ECLS) remains at 60%. Research and development has been slow, in part due to the lack of sophisticated experimental models. This publication introduces a dedicated rodent oxygenator (“RatOx”) and presents preliminary in vitro classification tests. The RatOx has an adaptable fiber module size for various rodent models. Gas transfer performances over the fiber module for different blood flows and fiber module sizes were tested according to DIN EN ISO 7199. At the maximum possible amount of effective fiber surface area and a blood flow of 100 mL/min, the oxygenator performance was tested to a maximum of 6.27 mL O₂/min and 8.2 mL CO₂/min, respectively. The priming volume for the largest fiber module is 5.4 mL, while the smallest possible configuration with a single fiber mat layer has a priming volume of 1.1 mL. The novel RatOx ECLS system has been evaluated in vitro and has demonstrated a high degree of compliance with all pre-defined functional criteria for rodent-sized animal models. We intend for the RatOx to become a standard testing platform for scientific studies on ECLS therapy and technology. Full article

The thickness nonuniformity of an electroformed layer is a bottleneck problem for electroformed micro metal devices. In this paper, a new fabrication method is proposed to improve the thickness uniformity of micro gear, which is the key element of various microdevices. The effect of the thickness of the photoresist on the uniformity was studied by simulation analysis, which showed that as the thickness of the photoresist increased, the thickness nonuniformity of the electroformed gear should decrease due to the reduced edge effect of the current density. Differently from the traditional method performed by one-step front lithography and electroforming, multi-step, self-aligned lithography and electroforming are used to fabricate micro gear structures in proposed method, which intermittently keeps the thickness of photoresist from decreasing during processes of alternate lithography and electroforming. The experimental results show that the thickness uniformity of micro gear fabricated by the proposed method was improved by 45.7% compared with that fabricated by the traditional method. Meanwhile, the roughness of the middle region of the gear structure was reduced by 17.4%. Full article

A common problem in deformable mirror assembly is that the adhesion of actuators to an optical mirror face sheet introduces unwanted topography due to large local stresses generated at the adhesive joint. A new approach to minimizing that effect is described, with inspiration taken from St. Venant’s principle, a fundamental precept in solid mechanics. It is demonstrated that moving the adhesive joint to the end of a slender post extending from the face sheet largely eliminates deformation due to adhesive stresses. A practical implementation of this design innovation is described, using silicon-on-insulator wafers and deep reactive ion etching. Simulation and experiments validate the effectiveness of the approach, reducing stress-induced topography on a test structure by a factor of 50. A prototype electromagnetic DM using this design approach is described, and its actuation is demonstrated. This new design can benefit a wide range of DMs that rely on actuator arrays that are adhesively bonded to a mirror face sheet. Full article

To demonstrate that the silicone-based polymer polydimethylsiloxane (PDMS) is suitable as a substrate for flexible/wearable antennae and sensors, an investigation of its various properties was carried out. The substrate was first developed in compliance with the requirements, and then its anisotropy was investigated using an experimental bi-resonator approach. This material exhibited modest but discernible anisotropy, with values of ~6.2/25 % for the dielectric constant and loss tangent, respectively. Its anisotropic behavior was confirmed by a parallel dielectric constant (ε_par) ~2.717 and an evaluated perpendicular dielectric constant (ε_perp) ~2.570—ε_par > ε_perp by 5.7%. Temperature affected PDMS’s dielectric properties. Lastly, the simultaneous impact of bending and anisotropy of the flexible substrate PDMS on the resonance properties of planar structures was also addressed, and these had diametrically opposed effects. PDMS appears to be a good contender as a substrate for flexible/wearable antennae and sensors based on all experimental evaluations conducted for this research. Full article

We report the microfabrication and characterization of concentric gold nanoring electrodes (Au NREs), which were fabricated by patterning two gold nanoelectrodes on the same silicon (Si) micropillar tip. Au NREs of 165 ± 10 nm in width were micropatterned on a 6.5 ± 0.2 µm diameter 80 ± 0.5 µm height Si micropillar with an intervening ~ 100 nm thick hafnium oxide insulating layer between the two nanoelectrodes. Excellent cylindricality of the micropillar with vertical sidewalls as well as a completely intact layer of a concentric Au NRE including the entire micropillar perimeter has been achieved as observed via scanning electron microscopy and energy dispersive spectroscopy data. The electrochemical behavior of the Au NREs was characterized by steady-state cyclic voltammetry and electrochemical impedance spectroscopy. The applicability of Au NREs to electrochemical sensing was demonstrated by redox cycling with the ferro/ferricyanide redox couple. The redox cycling amplified the currents by 1.63-fold with a collection efficiency of > 90% on a single collection cycle. The proposed micro-nanofabrication approach with further optimization studies shows great promise for the creation and expansion of concentric 3D NRE arrays with controllable width and nanometer spacing for electroanalytical research and applications such as single-cell analysis and advanced biological and neurochemical sensing. Full article

Flexible piezoresistive sensors (FPSs) have the advantages of compact structure, convenient signal acquisition and fast dynamic response; they are widely used in motion detection, wearable electronic devices and electronic skins. FPSs accomplish the measurement of stresses through piezoresistive material (PM). However, FPSs based on a single PM cannot achieve high sensitivity and wide measurement range simultaneously. To solve this problem, a heterogeneous multi-material flexible piezoresistive sensor (HMFPS) with high sensitivity and a wide measurement range is proposed. The HMFPS consists of a graphene foam (GF), a PDMS layer and an interdigital electrode. Among them, the GF serves as a sensing layer, providing high sensitivity, and the PDMS serves as a supporting layer, providing a large measurement range. The influence and principle of the heterogeneous multi-material (HM) on the piezoresistivity were investigated by comparing the three HMFPS with different sizes. The HM proved to be an effective way to produce flexible sensors with high sensitivity and a wide measurement range. The HMFPS-10 has a sensitivity of 0.695 kPa⁻¹, a measurement range of 0–14,122 kPa, fast response/recovery (83 ms and 166 ms) and excellent stability (2000 cycles). In addition, the potential application of the HMFPS-10 in human motion monitoring was demonstrated. Full article

As an emerging technology, smart textiles have attracted attention for rehabilitation purposes or to monitor heart rate, blood pressure, breathing rate, body posture, as well as limb movements. Traditional rigid sensors do not always provide the desired level of comfort, flexibility, and adaptability. To improve this, recent research focuses on the development of textile-based sensors. In this study, knitted strain sensors that are linear up to 40% strain with a sensitivity of 1.19 and a low hysteresis characteristic were integrated into different versions of wearable finger sensors for rehabilitation purposes. The results showed that the different finger sensor versions have accurate responses to different angles of the index finger at relaxation, 45° and 90°. Additionally, the effect of spacer layer thickness between the finger and sensor was investigated. Full article

This review paper presents the recent developments in spectroelectrochemical (SEC) technologies. The coupling of spectroscopy and electrochemistry enables SEC to do a detailed and comprehensive study of the electron transfer kinetics and vibrational spectroscopic fingerprint of analytes during electrochemical reactions. Though SEC is a promising technique, the usage of SEC techniques is still limited. Therefore, enough publicity for SEC is required, considering the promising potential in the analysis fields. Unlike previously published review papers primarily focused on the relatively frequently used SEC techniques (ultraviolet-visible SEC and surface-enhanced Raman spectroscopy SEC), the two not-frequently used but promising techniques (nuclear magnetic resonance SEC and dark-field microscopy SEC) have also been studied in detail. This review paper not only focuses on the applications of each SEC method but also details their primary working mechanism. In short, this paper summarizes each SEC technique’s working principles, current applications, challenges encountered, and future development directions. In addition, each SEC technique’s applicative research directions are detailed and compared in this review work. Furthermore, integrating SEC techniques into microfluidics is becoming a trend in minimized analysis devices. Therefore, the usage of SEC techniques in microfluidics is discussed. Full article

Nanoscale fluorescence emitters are efficient for measuring biomolecular interactions, but their utility for applications requiring single-unit observations is constrained by the need for large numerical aperture objectives, fluorescence intermittency, and poor photon collection efficiency resulting from omnidirectional emission. Photonic crystal (PC) structures hold promise to address the aforementioned challenges in fluorescence enhancement. In this review, we provide a broad overview of PCs by explaining their structures, design strategies, fabrication techniques, and sensing principles. Furthermore, we discuss recent applications of PC-enhanced fluorescence-based biosensors incorporated with emerging technologies, including nucleic acids sensing, protein detection, and steroid monitoring. Finally, we discuss current challenges associated with PC-enhanced fluorescence and provide an outlook for fluorescence enhancement with photonic-plasmonics coupling and their promise for point-of-care biosensing as well monitoring analytes of biological and environmental relevance. The review presents the transdisciplinary applications of PCs in the broad arena of fluorescence spectroscopy with broad applications in photo-plasmonics, life science research, materials chemistry, cancer diagnostics, and internet of things. Full article

The field of soft matter is rapidly growing and pushing the limits of conventional materials science and engineering. Soft matter refers to materials that are easily deformed by thermal fluctuations and external forces, allowing for better adaptation and interaction with the environment. This has opened up opportunities for applications such as stretchable electronics, soft robotics, and microfluidics. In particular, soft matter plays a crucial role in microfluidics, where viscous forces at the microscale pose a challenge to controlling dynamic material behavior and operating functional devices. Field-driven active colloidal systems are a promising model system for building smart functional devices, where dispersed colloidal particles can be activated and controlled by external fields such as magnetic and electric fields. This review focuses on building smart functional devices from field-driven collective patterns, specifically the dynamic structuring of hierarchically ordered structures. These structures self-organize from colloidal building blocks and exhibit reconfigurable collective patterns that can implement smart functions such as shape shifting and self-healing. The review clarifies the basic mechanisms of field-driven particle dynamic behaviors and how particle–particle interactions determine the collective patterns of dynamic structures. Finally, the review concludes by highlighting representative application areas and future directions. Full article

Terahertz metamaterials are some of the core components of the new generation of high-frequency optoelectronic devices, which have excellent properties that natural materials do not have. The unit structures are generally much smaller than the wavelength, so preparation is mainly based on semiconductor processes, such as coating, photolithography and etching. Although the processing resolution is high, it is also limited by complex processing, long cycles, and high cost. In this paper, a design method for dual-band terahertz metamaterials and a simple, rapid, low-cost metamaterial preparation scheme based on step-motor-driven electrohydrodynamic jet technology are proposed. By transforming an open-source 3D printer, the metamaterial structures can be directly printed without complex semiconductor processes. To verify effectiveness, the sample was directly printed using nano conductive silver paste as consumable material. Then, a fiber-based multi-mode terahertz time-domain spectroscopy system was built for testing. The experimental results were in good agreement with the theoretical simulation. Full article

This paper, for the first time, reports an electrically inspired flexible electrochemical film power supply for long-term epidermal sensors. This device can periodically provide electrical power for several hours after a short-time electrical activation. The electrical activation makes acetylcholine, which is infused into the subcutaneous tissue by iontophoresis. The interstitial fluid (ISF) with glucose molecules is then permeated autonomously for several hours. At this period, the device can provide electrical power. The electrical power is generated from the catalyzing reaction between the glucose oxidase immobilized on the anode and the permeated glucose molecules. After the ISF permeation stops, we give a short-time electrical activation to provide electrical power for several hours again. The power supply is flexible, which makes it adaptively conform to skin. The episodic short-time electrical activation can be enabled by an integrated small film lithium-ion battery. This method extends the service life of a lithium-ion battery 10-fold and suggests the application of small lithium-ion batteries for long-term epidermal sensors. Full article

Bacteria primarily live in structured environments, such as colonies and biofilms, attached to surfaces or growing within soft tissues. They are engaged in local competitive and cooperative interactions impacting our health and well-being, for example, by affecting population-level drug resistance. Our knowledge of bacterial competition and cooperation within soft matrices is incomplete, partly because we lack high-throughput tools to quantitatively study their interactions. Here, we introduce a method to generate a large amount of agarose microbeads that mimic the natural culture conditions experienced by bacteria to co-encapsulate two strains of fluorescence-labeled Escherichia coli. Focusing specifically on low bacterial inoculum (1–100 cells/capsule), we demonstrate a study on the formation of colonies of both strains within these 3D scaffolds and follow their growth kinetics and interaction using fluorescence microscopy in highly replicated experiments. We confirmed that the average final colony size is inversely proportional to the inoculum size in this semi-solid environment as a result of limited available resources. Furthermore, the colony shape and fluorescence intensity per colony are distinctly different in monoculture and co-culture. The experimental observations in mono- and co-culture are compared with predictions from a simple growth model. We suggest that our high throughput and small footprint microbead system is an excellent platform for future investigation of competitive and cooperative interactions in bacterial communities under diverse conditions, including antibiotics stress. Full article

Step emulsification, which uses a geometry-dependent mechanism for generating uniformly sized droplets, has recently gained considerable attention because of its robustness against flow fluctuations. However, like shear-based droplet generation, step emulsification is susceptible to impurities caused by satellite droplets. Herein, we demonstrate the integration of deterministic lateral displacement (DLD) to separate the main and satellite droplets produced during step emulsification. Step-emulsification nozzles (16 μm deep) in the upstream region of the proposed device were arrayed on the sidewalls of the main channel (91 μm deep). In the downstream region, the DLD micropillars were arrayed periodically with a critical diameter (cut-off value for size-based separation) of 37 μm. When an acrylate monomer and aqueous polyvinyl alcohol solution were infused as the dispersed and continuous phases, respectively, the nozzles produced monodisperse main droplets in the dripping regime, with an average diameter of ~60 μm, coefficient of variation (CV) value below 3%, and satellite droplets of ~3 μm. Upon entering the DLD region near the sidewall, these main and satellite droplets were gradually separated through the pillars based on their sizes. Finally, off-chip photopolymerization yielded monodisperse polymeric microspheres with an average diameter of 55 μm and a CV value of 2.9% (n = 202). Full article

Microneedles are gaining a lot of attention in the context of sampling cutaneous biofluids such as capillary blood. Their minimal invasiveness and user-friendliness make them a prominent substitute for venous puncture or finger-pricking. Although the latter is suitable for self-sampling, the impracticality of manual handling and the difficulty of obtaining enough qualitative sample is driving the search for better solutions. In this context, hollow microneedle arrays (HMNAs) are particularly interesting for completely integrating sample-to-answer solutions as they create a duct between the skin and the sampling device. However, the fabrication of sharp-tipped HMNAs with a high aspect ratio (AR) is challenging, especially since a length of ≥1500 μm is desired to reach the blood capillaries. In this paper, we first described a novel two-step fabrication protocol for HMNAs in stainless steel by percussion laser drilling and subsequent micro-milling. The HMNAs were then integrated into a self-powered microfluidic sampling patch, containing a capillary pump which was optimized to generate negative pressure differences up to 40.9 ± 1.8 kPa. The sampling patch was validated in vitro, showing the feasibility of sampling 40 μL of liquid. It is anticipated that our proof-of-concept is a starting point for more sophisticated all-in-one biofluid sampling and point-of-care testing systems. Full article

In this paper, we propose a method to generate multi-depth phase-only holograms using stochastic gradient descent (SGD) algorithm with weighted complex loss function and masked multi-layer diffraction. The 3D scene can be represented by a combination of layers in different depths. In the wave propagation procedure of multiple layers in different depths, the complex amplitude of layers in different depths will gradually diffuse and produce occlusion at another layer. To solve this occlusion problem, a mask is used in the process of layers diffracting. Whether it is forward wave propagation or backward wave propagation of layers, the mask can reduce the occlusion problem between different layers. Otherwise, weighted complex loss function is implemented in the gradient descent optimization process, which analyzes the real part, the imaginary part, and the amplitude part of the focus region between the reconstructed images of the hologram and the target images. The weight parameter is used to adjust the ratio of the amplitude loss of the focus region in the whole loss function. The weight amplitude loss part in weighted complex loss function can decrease the interference of the focus region from the defocus region. The simulations and experiments have validated the effectiveness of the proposed method. Full article

Colloidal CdSe/ZnS quantum dots (QD) enhanced micro-LEDs with sizes varying from 10 to 100 μm were fabricated and measured. The direct photolithography of quantum-dot-contained photoresists can place this color conversion layer on the top of an InGaN-based micro-LED and have a high throughput and semiconductor-grade precision. Both the uncoated and coated devices were characterized, and we determined that much higher brightness of a QD-enhanced micro-LED under the same current level was observed when compared to its AlGaInP counterpart. The color stability across the device sizes and injection currents were also examined. QD LEDs show low redshift of emission wavelength, which was recorded within 1 nm in some devices, with increasing current density from 1 to 300 A/cm². On the other hand, the light conversion efficiency (LCE) of QD-enhanced micro-LEDs was detected to decrease under the high current density or when the device is small. The angular intensities of QD-enhanced micro-LEDs were measured and compared with blue devices. With the help of the black matrix and omnidirectional light emission of colloidal QD, we observed that the angular intensities of the red and blue colors are close to Lambertian distribution, which can lead to a low color shift in all angles. From our study, the QD-enhanced micro-LEDs can effectively increase the brightness, the color stability, and the angular color match, and thus play a promising role in future micro-display technology. Full article

The lab-on-a-chip concept, enabled by microfluidic technology, promises the integration of multiple discrete laboratory techniques into a miniaturised system. Research into microfluidics has generally focused on the development of individual elements of the total system (often with relatively limited functionality), without full consideration for integration into a complete fully optimised and miniaturised system. Typically, the operation of many of the reported lab-on-a-chip devices is dependent on the support of a laboratory framework. In this paper, a demonstrator platform for routine laboratory analysis is designed and built, which fully integrates a number of technologies into a single device with multiple domains such as fluidics, electronics, pneumatics, hydraulics, and photonics. This facilitates the delivery of breakthroughs in research, by incorporating all physical requirements into a single device. To highlight this proposed approach, this demonstrator microsystem acts as a fully integrated biochemical assay reaction system. The resulting design determines enzyme kinetics in an automated process and combines reservoirs, three-dimensional fluidic channels, optical sensing, and electronics in a low-cost, low-power and portable package. Full article

An acicular microtextured sheet was developed as a heat radiation device from the high-temperature source to the cooling medium in the infrared (IR) spectrum. The copper surface was modified by acicular micro-texturing to place a semi-regular micro-/nano-cone structure onto it. FT-IR (Fourier transformation IR) spectroscopy was utilized to measure the transmittance diagram in near-IR to far-IR wavelengths. The wavelength (λ) of 6.7 μm, where the highest absorbance valley was detected in the diagram, was equivalent to the doubled size of the micro-cone average height, with H_ave = 3.3 μm; λ ~ 2 × H_ave. The electromagnetic waves in the far-IR wavelength were emitted by acicular micro-textured metallic sheets. The heat radiation transfer experiment was performed to describe this low-temperature heat radiation behavior. No temperature rise was detected on the black-colored polycarbonate (BC-PC) plate away from the bare copper sheet without textures, located on the high-temperature source. The temperature increased by 4 K on the BC-PC plate using the acicular textured copper sheet device. The emitter temperature also decreased significantly by 50 K or 50% of the heat source temperature. Full article

Core–shell particles are micro- or nanoparticles with solid, liquid, or gas cores encapsulated by protective solid shells. The unique composition of core and shell materials imparts smart properties on the particles. Core–shell particles are gaining increasing attention as tuneable and versatile carriers for pharmaceutical and biomedical applications including targeted drug delivery, controlled drug release, and biosensing. This review provides an overview of fabrication methods for core–shell particles followed by a brief discussion of their application and a detailed analysis of their manipulation including assembly, sorting, and triggered release. We compile current methodologies employed for manipulation of core–shell particles and demonstrate how existing methods of assembly and sorting micro/nanospheres can be adopted or modified for core–shell particles. Various triggered release approaches for diagnostics and drug delivery are also discussed in detail. Full article

Monitoring of ions in real-time directly in cell culture systems and in organ-on-a-chip platforms represents a significant investigation tool to understand ion regulation and distribution in the body and ions’ involvement in biological mechanisms and specific pathologies. Innovative flexible sensors coupling electrochemical stripping analysis (square wave anodic stripping voltammetry, SWASV) with an ion selective membrane (ISM) were developed and integrated in Transwell™ cell culture systems to investigate the transport of zinc and copper ions across a human intestinal Caco-2 cell monolayer. The fabricated ion-selective sensors demonstrated good sensitivity (1 × 10⁻¹¹ M ion concentration) and low detection limits, consistent with pathophysiological cellular concentration ranges. A non-invasive electrochemical impedance spectroscopy (EIS) analysis, in situ, across a selected spectrum of frequencies (10–10⁵ Hz), and an equivalent circuit fitting were employed to obtain useful electrical parameters for cellular barrier integrity monitoring. Transepithelial electrical resistance (TEER) data and immunofluorescent images were used to validate the intestinal epithelial integrity and the permeability enhancer effect of ethylene glycol-bis(2-aminoethylether)-N,N,N’,N’-tetraacetic acid (EGTA) treatment. The proposed devices represent a real prospective tool for monitoring cellular and molecular events and for studies on gut metabolism/permeability. They will enable a rapid integration of these sensors into gut-on-chip systems. Full article

The local integration of metal nanoparticle films on 3D-structured polydimethylsiloxane (PDMS)-based microfluidic devices is of high importance for applications including electronics, electrochemistry, electrocatalysis, and localized Raman sensing. Conventional processes to locally deposit and pattern metal nanoparticles require multiple steps and shadow masks, or access to cleanroom facilities, and therefore, are relatively imprecise, or time and cost-ineffective. As an alternative, we present an aerosol-based direct-write method, in which patterns of nanoparticles generated via spark ablation are locally printed with sub-mm size and precision inside of microfluidic structures without the use of lithography or other masking methods. As proof of principle, films of Pt or Ag nanoparticles were printed in the chambers of a multiplexed microfluidic device and successfully used for two different applications: Screening electrochemical activity in a high-throughput fashion, and localized sensing of chemicals via surface-enhanced Raman spectroscopy (SERS). The versatility of the approach will enable the generation of functional microfluidic devices for applications that include sensing, high-throughput screening platforms, and microreactors using catalytically driven chemical conversions. Full article

Cancers, chronic diseases and respiratory infections are major causes of mortality and present diagnostic and therapeutic challenges for health care. There is an unmet medical need for non-invasive, easy-to-use biomarkers for the early diagnosis, phenotyping, predicting and monitoring of the therapeutic responses of these disorders. Exhaled breath sampling is an attractive choice that has gained attention in recent years. Exhaled nitric oxide measurement used as a predictive biomarker of the response to anti-eosinophil therapy in severe asthma has paved the way for other exhaled breath biomarkers. Advances in laser and nanosensor technologies and spectrometry together with widespread use of algorithms and artificial intelligence have facilitated research on volatile organic compounds and artificial olfaction systems to develop new exhaled biomarkers. We aim to provide an overview of the recent advances in and challenges of exhaled biomarker measurements with an emphasis on the applicability of their measurement as a non-invasive, point-of-care diagnostic and monitoring tool. Full article

Polycrystalline boron-doped diamond (BDD) films were surface nanotextured by femtosecond pulsed laser irradiation (100 fs duration, 800 nm wavelength, 1.44 J cm⁻² single pulse fluence) to analyse the evolution of induced alterations on the surface morphology and structural properties. The aim was to identify the occurrence of laser-induced periodic surface structures (LIPSS) as a function of the number of pulses released on the unit area. Micro-Raman spectroscopy pointed out an increase in the graphite surface content of the films following the laser irradiation due to the formation of ordered carbon sites with respect to the pristine sample. SEM and AFM surface morphology studies allowed the determination of two different types of surface patterning: narrow but highly irregular ripples without a definite spatial periodicity or long-range order for irradiations with relatively low accumulated fluences (<14.4 J cm⁻²) and coarse but highly regular LIPSS with a spatial periodicity of approximately 630 nm ± 30 nm for higher fluences up to 230.4 J cm⁻². Full article

Recently, there has been growing interest in using lightwave-driven scanning probe microscopy (LD-SPM) to break through the Abbe diffraction limit of focusing, yielding insight into various energy couplings and conversion processes and revealing the internal information of matter. We describe a compact and efficient optical cryostat designed for LD-SPM testing under magnetic fields. The exceptional multilayer radiation shielding insert (MRSI) forms an excellent temperature gradient when filled with heat conducting gas, which removes the requirement to install an optical window in the liquid helium cooling shell. This not only critically avoids the vibration and thermal drift caused by solid heat conduction but also minimizes light transmission loss. The application of gate valves and bellows allows a simpler and more effective replacement of the sample and working cell in the test cavity. ANSYS software is used for steady-state thermal analysis of the MRSI to obtain the temperature distribution and heat transfer rate, and the necessity of the flexible copper shielding strips is illustrated by the simulations. The topography and magnetic domain images of 45 nm-thick La_0.67Ca_0.33MnO₃ thin films on NdGaO₃(001) substrates under a magnetic field were obtained by a self-made lightwave-driven magnetic force microscope in this cryostat. The resolution and noise spectra during imaging reveal temperature stability and low vibration throughout the cryostat. The experience acquired during the development of this cryostat will help to establish cryostats of similar types for a variety of optic applications requiring the use of cryogenic temperatures. Full article

Atomic force microscopy (AFM) in conjunction with microfluidic delivery was utilized to produce three-dimensional (3D) lipid structures following a custom design. While AFM is well-known for its spatial precision in imaging and 2D nanolithography, the development of AFM-based nanotechnology into 3D nanoprinting requires overcoming the technical challenges of controlling material delivery and interlayer registry. This work demonstrates the concept of 3D nanoprinting of amphiphilic molecules such as 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine (POPC). Various formulations of POPC solutions were tested to achieve point, line, and layer-by-layer material delivery. The produced structures include nanometer-thick disks, long linear spherical caps, stacking grids, and organizational chiral architectures. The POPC molecules formed stacking bilayers in these constructions, as revealed by high-resolution structural characterizations. The 3D printing reached nanometer spatial precision over a range of 0.5 mm. The outcomes reveal the promising potential of our designed technology and methodology in the production of 3D structures from nanometer to continuum, opening opportunities in biomaterial sciences and engineering, such as in the production of 3D nanodevices, chiral nanosensors, and scaffolds for tissue engineering and regeneration. Full article

Intraocular pressure (IOP) is a key indicator to evaluate the risk and status of glaucoma, which is one of the main causes of irreversible blindness. However, the IOP value is susceptible to circadian changes and is difficult to be measured real−time. In this paper, we designed a thin−film integrated optical IOP sensor based on the interferometry principle, which could read out the IOP value by interference patterns and monitor the value changes real−time at the same time. The theoretical and experimental results indicated that our sensor exhibited a sensitivity of 0.19 μm/mmHg and an average accuracy of 0.84 mmHg over the pressure range of 0–45 mmHg, which is comparable with the other reported optical systems but with the advantage of easier fabrication process and low−cost. Our sensor device implies great potential in the application of human physiological index measurement and other chip−integrated medical sensing instruments. Full article

The ability to manipulate a liquid meniscus using electrowetting has many applications. In any electrowetting design, at least two electrodes are required: one forms the field to change the contact angle and the other functions as a ground electrode. The contribution of the ground electrode (GE) to the dynamics of electrowetting has not yet been thoroughly investigated. In this paper, we discovered that with a bare ground electrode, the contact angle of a sessile drop increases instead of decreases when a direct current (DC) voltage varying from zero to the threshold voltage is applied. This phenomenon is opposite to what occurs when the GE is coated with a dielectric, where the contact-angle change follows the Lippmann–Young equation above the threshold voltage of electrowetting. However, this behaviour is not observed with either a dielectric-coated electrode using direct current (DC) or a bare ground electrode using alternating current (AC) voltage electrowetting. This study explains this phenomenon with finite element simulation and theory. From previous research work, the ground electrode configuration is inconsistent. In some studies, the ground electrode is exposed to water; in other studies, the ground electrode is covered with dielectric. This study identified that an exposed ground electrode is not required in electrowetting. Moreover, this research work suggests that for applications where precise control of the contact angle is paramount, a dielectric-coated ground electrode should be used since it prevents the increase in the contact angle when increasing the applied potential from zero to the threshold voltage. This study also identified that contact angle hysteresis is lower with a Cytop-coated ground electrode and DC voltage than with a bare ground electrode using AC or DC voltages. Full article

As rheological properties are substantially influenced by red blood cells (RBCs) and plasma, the separation of their individual contributions in blood is essential. The estimation of multiple rheological factors is a critical issue for effective early detection of diseases. In this study, three rheological properties (i.e., viscoelasticity, RBC aggregation, and blood junction pressure) are measured by analyzing the blood velocity and image intensity in a microfluidic device. Using a single syringe pump, the blood flow rate sets to a pulsatile flow pattern (Q_b[t] = 1 + 0.5 sin(2πt/240) mL/h). Based on the discrete fluidic circuit model, the analytical formula of the time constant (λ_b) as viscoelasticity is derived and obtained at specific time intervals by analyzing the pulsatile blood velocity. To obtain RBC aggregation by reducing blood velocity substantially, an air compliance unit (ACU) is used to connect polyethylene tubing (i.d. = 250 µm, length = 150 mm) to the blood channel in parallel. The RBC aggregation index (AI) is obtained by analyzing the microscopic image intensity. The blood junction pressure (β) is obtained by integrating the blood velocity within the ACU. As a demonstration, the present method is then applied to detect either RBC-aggregated blood with different concentrations of dextran solution or hardened blood with thermally shocked RBCs. Thus, it can be concluded that the present method has the ability to consistently detect differences in diluent or RBCs in terms of three rheological properties. Full article