Low Power Sensors for Wireless Communication and Localization

Due to the rapid growth of electronic information technology, the need for the higher stability of crystal oscillators has increased. The temperature-compensated X’tal (crystal) oscillator (TCXO), a type of crystal oscillator with high frequency stability, has been widely used in communications, sensor networks, automotive electronics, industrial control, measuring devices, and other equipment. The traditional TCXO only performs frequency compensation based on the current temperature, without considering the error caused by thermal hysteresis. As the frequency stability of the TCXO improves, the thermal hysteresis of the crystal oscillator has a negligible influence on the frequency stability of the crystal oscillator. This study measured different compensation tables for hysteresis curves at different temperatures and used a microprocessor to store the historical information of crystal temperature changes. Furthermore, corresponding algorithms were designed to select the correct values, according to the temperature change history, to compensate for the thermal hysteresis of the crystal oscillator error. Experiments show that this method can reduce the hysteresis error of the crystal oscillator from 700 to 150 ppb (−40 to 80 °C). Full article

The paper deals with the localization in a low-power wide-area-network (LPWAN) operating long-range wide-area-network (LoRaWAN) technology. The LoRaWAN is, today, one of the most widely used connectivity-enabling technologies for the battery-powered smart devices employed in a broad range of applications. Many of these applications either require or can benefit from the availability of geolocation information. The use of global positioning system (GPS) technology is restrained by the bad propagation of the signal when the device is hidden indoors, and by energy consumption such a receiver would require. Therefore, this paper focuses on an alternative solution implying the use of the information readily available in the LoRaWAN network and application of the time difference of arrival (TDoA) method for the passive geolocation of end-devices in the network. First, the limits of geolocation services in networks that use narrow-band communication channels are discussed, as well as the relevant challenges faced by the TDoA approach. Then, we select five classic TDoA algorithms and evaluate their performance using simulation. Based on these results, we select the two providing the best accuracy (i.e., Chan’s and Foy’s). These algorithms were tested by the field measurements, using the specially designed low-cost gateways and test devices to estimate their real-life performance. Full article

With the growth of the number of IoT devices, the need for changing batteries is becoming cumbersome and has a significant environmental impact. Therefore, batteryless and maintenance-free IoT solutions have emerged, where energy is harvested from the ambient environment. Energy harvesting is relevant mainly for the devices that have a low energy consumption in the range of thousands of micro-watts. Bluetooth Low Energy (BLE) is one of the most popular technologies and is highly suitable for such batteryless energy harvesting devices. Specifically, the BLE friendship feature allows a Low Power Node (LPN) to sleep most of the time. An associated friend node (FN) temporarily stores the LPN’s incoming data packets. The LPN wakes up and polls periodically to its FN retrieving the stored data. Unfortunately, the LPNs typically experience high downlink (DL) latency. To resolve the latency issue, we propose combining the batteryless LPN with a secondary ultra-low-power wake-up radio (WuR), which enables it to always listen for an incoming wake-up signal (WuS). The WuR allows the FN to notify the LPN when new DL data is available by sending a WuS. This removes the need for frequent polling by the LPN, and thus saves the little valuable energy available to the batteryless LPN. In this article, we compare the standard BLE duty-cycle based polling and WuR-based data communication between an FN and a batteryless energy-harvesting LPN. This study allows optimising the LPN configuration (such as capacitor size, polling interval) based on the packet arrival rate, desired packet delivery ratio and DL latency at different harvesting powers. The result shows that WuR-based communication performs best for high harvesting power (400 $\mathsf{\mu }$W and above) and supports Poisson packet arrival rates as low as 1 s with maximum PDR using a capacitor of 50 mF or more. Full article

Multiple Radio Access Technology (multi-RAT) communication with Low Power Wide Area Networks (LPWAN) significantly increases the flexibility of Internet of Things (IoT) applications. Location-based services that build upon such a multimodal communication architecture are able to switch to an optimal localization method depending on the constraints of the active wireless technology. Furthermore, the resulting location estimate can aid location-based handover mechanisms to reduce the energy consumption of a multi-RAT IoT device. In this research, we present our design of a multimodal localization framework and illustrate the benefit of such a framework with two IoT use case examples. For the first use case, valuable artwork is tracked during transportation to a museum. In the second use case, we monitor the usage and location of large construction tools. Finally, we propose how our localization framework can be improved to deal with implementation challenges and to reduce location estimation errors. Full article

Emergency communications need to meet the developing demand of equipment and the complex scenarios of network in public safety networks (PSNs). Heterogeneous Cloud Radio Access Network (H-CRAN), an important technology of the 5th generation wireless systems (5G), plays an important role in PSN. H-CRAN has the features of resource sharing and centralized allocation which can make up for resource shortage in emergency communications. Therefore, an emergency communications strategy based on Device-to-device (D2D) multicast is proposed to make PSN more flexible and rapid. Nearby users can communicate directly without a base station through D2D. This strategy may guarantee high speed data transmission and stable continuous real-time communications. It is divided into three steps. Firstly, according to the distance between users, the alternative cluster head is divided. Secondly, two kinds of cluster head user selection schemes are developed. One is based on terminal power and the other is based on the number of extended users. Last but not least, the Hungarian Algorithm based on throughput-aware is used to channel multiplexing. The numerical results show that the proposed scheme can effectively extend the coverage of PSN and optimize the utilization of resources. Full article