Organic Pollution in Soil and Groundwater

Clay is widely encountered in nature and directly influences seepage behaviors, exerting a crucial impact on engineering applications. Under low hydraulic gradients, seepage behaviors have been observed to deviate from Darcy’s law, displaying a non-linear trend. However, the impacts of clay content on non-linear seepage behavior and its pore-scale mechanisms to date remain unclear. In this study, constant-head seepage experiments were conducted in sand–clay porous media under various hydraulic gradients. Low-field nuclear magnetic resonance (LF-NMR) technology was utilized to monitor the bound-water and free-water contents of sand–clay porous media under different seepage states. The results show a threshold hydraulic gradient (i₀) below which there is no flow, and a critical hydraulic gradient (i_cr) below which the relationship between the hydraulic gradient (i) and seepage velocity (v) is non-linear. Both hydraulic gradients increased with clay content. Moreover, the transformation between bound water and free water was observed during the seepage-state evolution (no flow to pre-Darcy or pre-Darcy to Darcy). As the hydraulic gradient reached the i₀, the pore water pressure gradually overcame the adsorption force of the bound-water film, reducing the thickness of the bound-water film, and causing non-linear seepage behavior. When i₀ < i < i_cr, the enlarging hydraulic gradient triggers the thinning of bound water and enhances the fluidity of pore water. Moreover, the increasing clay content augments the bound-water content required for the seepage state’s change. Full article

The impact of chain length on the sorption of anionic PFAS by soils and sediments was investigated by aggregating and synthesizing data sets from the literature. Quantitative structure/property relationship (QSPR) analysis was applied to characterize the influence of molecular size and soil properties on sorption. The log of the organic carbon-normalized equilibrium sorption coefficient (K_oc) exhibited a biphasic relationship with molar volume, wherein the log K_oc values for the short-chain PFAS were generally greater than would be predicted using the QSPR correlation determined for the long-chain PFAS. This enhanced differential sorption is observed to different degrees for all studies, which are compiled and synthesized for the first time. The results reveal remarkable congruency across a wide array of soils comprising a large range of properties and indicate that the observed enhanced differential sorption of short-chain PFAS is a prevalent phenomenon. Aggregating the long-chain PFAS data for all soils and sediments with organic carbon contents > 1% produced a strong correlation, indicating that the resultant QSPR model can produce representative log K_oc values irrespective of the other properties of the medium. Silt+clay content was shown to be an important soil component for the short-chain PFAS for most soils, as well as the long-chain PFAS for soils with organic carbon contents < 1%. The results indicate that while the simple K_oc-f_oc approach may produce reasonable estimates of K_d values for long-chain anionic PFAS, particularly for soils and sediments with larger organic carbon contents, it is unlikely to do so for short-chain anionic PFAS. Full article

The microbially-induced calcium carbonate precipitation (MICP) technique has shown great robustness in dealing with soil and groundwater contamination problems. A typical result of the implementation of MICP technique is a change in the pore structure. In this study, the effects of MICP on the pore structure of yellow sandstone from the Zigong area, Sichuan, China under different conditions, (e.g., temperature, pH, and calcium ion concentration) are investigated using LF-NMR resonance. The pore network of yellow sandstone is accurately measured using the peak area of the T₂ spectral signal. The distribution of calcium carbonate in the pores of the yellow sandstone is characterized by the magnitude of the T₂ signal variation. The results show that the precipitation of calcium carbonate caused by MICP tends to be deposited in relatively large pores. However, the calcium carbonate precipitates in the smaller pores at a higher temperature. A higher pH considerably enhances the precipitation, and the alkaline environment tends to cause the precipitation of the calcium carbonate in the large pores. Although the amount of produced calcium carbonate continuously increases as the MCIP process continues, which is expected, the production efficiency decreases steadily. Full article

To investigate the pollution characteristics of the surface sediments of the river–reservoir system in the Feiyun River basin, a sediment heavy metal survey was conducted for the first time in the Feiyun River basin. Surface sediments from 21 sampling sites in the Feiyun River basin were collected, and the concentrations and spatial distribution characteristics of 15 heavy metals (Cr, Ni, Cu, Zn, As, Cd, Pb, Mn, V, Co, Mo, Sb, W, Fe, and Se) were analyzed. Three heavy metal ecological risk assessment methods were used to evaluate the potential risks of heavy metals in sediments, and the sources of major heavy metals were traced by correlation analysis and principal component analysis. The results show that (1) the average concentration of heavy metals (As) (212.64 mg/kg) and (Sb) (4.89 mg/kg) in Feiyun River Basin is 33.3 and 6.89 times the background value of Zhejiang Province; the overall spatial distribution of heavy metals is: the mainstream of Feiyun River > Zhaoshandu Reservoir > Shanxi Reservoir, thereby, the pollution is relatively significant; (2) by processing the geo-accumulation index and enrichment index methods, As and Sb are classified as ‘severely polluted’, ‘moderately severely polluted’ and ‘severely polluted’, ‘very severe polluted’ respectively; (3) the potential ecological index evaluates the surface sediments in the Feiyun River Basin as a very high risk level, the main environmental risk factors are As, Sb, Cd and Mo; (4) the principal component analysis results show that the heavy metals in the sediments of the Feiyun River Basin may be mainly affected by human activities such as sewage from domestic and agricultural activities, mining and smelting, and the others are affected by natural factors. Full article

Polycyclic aromatic hydrocarbons (PAHs) are widespread in the environment and pose a serious threat to the soil ecosystem. In order to better understand the health risks for residents exposed to PAH-contaminated soil, 173 surface soil samples were collected in Shanxi Province, China, to detect the levels of 16 priority PAHs. The spatial distribution patterns of PAHs were explored using interpolation and spatial clustering analysis, and the probable sources of soil PAHs were identified for different land-use covers. The results indicate that the soil Σ16 PAH concentration ranged from 22.12 to 1337.82 ng g⁻¹, with a mean of 224.21 ng g⁻¹. The soils were weakly to moderately contaminated by high molecular weight PAHs (3–5 ring) and the Taiyuan–Linfen Basin was the most polluted areas. In addition, the concentration of soil PAHs on construction land was higher than that on other land-use covers. Key sources of soil PAHs were related to industrial activities dominated by coal burning, coking, and heavy traffic. Based on the exposure risk assessment of PAHs, more than 10% of the area was revealed to be likely to suffer from high carcinogenic risks for children. The study maps the high-risk distribution of soil PAHs in Shanxi Province and provides PAH pollution reduction strategies for policy makers to prevent adverse health risks to residents. Full article

Leaded fuel has been reported to contain certain amounts of toxic trace metals such as Pb and Cadmium (Cd), which may have negative impacts on humans and the environment. Unleaded fuel was introduced to South Africa in 2006 with the aim of reducing and eventually eliminating the negative impact of leaded fuel on the environment. However, trace metals are usually nonbiodegradable, and it may therefore be necessary to monitor their presence in the environment so as to evaluate their possible impact on human health. The present study evaluated the levels of Pb and other heavy metals in soil samples collected from petrol (gas) filling stations and from busy roads just around the filling stations in Pretoria, South Africa, fifteen years after the introduction of unleaded fuel. A total of twenty-four (24) soil samples were analysed for lead (Pb), chromium (Cr), copper (Cu), zinc (Zn), arsenic (As), iron (Fe), manganese (Mn), nickel (Ni), titanium (Ti), and cadmium (Cd) using Inductively Coupled Plasma Mass Spectrometry (ICP-MS). The results showed that the concentrations of the trace metals were in the following ranges: Pb, 0.08 ± 0.02–188.36 ± 15.32 ug/g; Mn, 5.35 ± 0.34–6842.43 ± 1.35 ug/g; Zn, 1.82 ± 0.22–9814.89 ± 22.32 ug/g; As, 0.21 ± 0.00–8.42 ± 2.44 ug/g; Cu, 10.51 ± 3.41–859 ± 0.09 ug/g; Cr, 5.80 ± 2.21–417.70 ± 9.08 ug/g; Ti, 19.94 ± 4.99–1036.12 ± 1.49 ug/g; and Fe, 3.06 ± 7.87–674.07 ± 12.22 mg/g. The highest concentrations from all the elements were recorded for Fe in all the collected soil samples. The concentrations of Pb in the soils collected from sites associated with high traffic and industrial areas were higher than for those from all other sites, and the differences were significant (p < 0.05). The pollution index (PI), which is the anthropogenic influence of the trace metals, and the geoaccumulation (Igeo), which allows for the removal of possible variations as regards the studied element in the soil due to the possible differences in the background value, showed that some samples were enriched anthropogenically. The PI for Ni, Pb, Cu, and Cr indicated highly anthropogenically contaminated soils, especially at sites associated with high traffic volumes and in industrial areas. The Igeo showed moderately polluted areas for Pb and Cu in high-traffic areas. The exposure routes for the toxic trace metals that were of concern in the study were either through ingestion or dermal contact. The calculated hazard quotient showed both noncarcinogenic and carcinogenic risks for Fe and Mn via ingestion and through dermal contact for both children and adults, respectively. The concentrations of Pb were high and similar to those that were previously reported in the study and pointed to vehicular emission as one of the contributors. The study also noticed an increase in the presence of Mn and Fe in all soil samples. Full article

The presence of pesticide residues in groundwater, many years after their phase out in European Union verifies that the persistence in aquifer is much higher than in other environmental compartments. Currently used and banned pesticides were monitored in Northern Greece aquifers and a human health risk assessment was conducted. The target compounds were the herbicides metolachlor (MET), terbuthylazine (TER), atrazine (ATR) and its metabolites deisopropylatrazine (DIA), deethylatrazine (DEA) and hydroxyatrazine (HA). Eleven sampling sites were selected to have representatives of different types of wells. Pesticides were extracted by solid-phase extraction and analyzed by liquid chromatography. MET was detected in 100% of water samples followed by ATR (96.4%), DEA and HA (88.6%), DIA (78.2%) and TER (67.5%). ATR, DIA, DEA, HA, MET and TER mean concentrations detected were 0.18, 0.29, 0.14, 0.09, 0.16 and 0.15 μg/L, respectively. Obtained results were compared with historical data from previous monitoring studies and temporal trends were assessed. Preferential flow was the major factor facilitating pesticide leaching within the month of herbicide application. Moreover, apparent age of groundwater and the reduced pesticide dissipation rates on aquifers resulted of long-term detection of legacy pesticides. Although atrazine had been banned more than 18 years ago, it was detected frequently and their concentrations in some cases were over the maximum permissible limit. Furthermore, human health risk assessment of pesticides was calculated for two different age groups though drinking water consumption. In all examined wells, the sum of the HQ values were lower than the unity. As a result, the analyzed drinking water wells are considered safe according to the acute risk assessment process. However, the presence of atrazine residues causes concerns related with chronic toxicity, since ATR R values were greater than the parametric one of 1 × 10⁻⁶ advised by USEPA, for both age groups. Full article

Estimating groundwater quality parameters through conventional methods is time-consuming through laboratory measurements for megacities. There is a need to develop models that can help decision-makers make policies for sustainable groundwater reserves. The current study compared the efficiency of multivariate linear regressions (MLR) and artificial neural network (ANN) models in the prediction of groundwater parameters for total dissolved solids (TDS) for three sub-divisions in Lahore, Pakistan. The data for this study were collected every quarter of a year for six years. ANN was applied to investigate the feasibility of feedforward, backpropagation neural networks with three training functions T-BR (Bayesian regularization backpropagation), T-LM (Levenberg–Marquardt backpropagation), and T-SCG (scaled conjugate backpropagation). Two activation functions were used to analyze the performance of algorithmic training functions, i.e., Logsig and Tanh. Input parameters of pH, electrical conductivity (EC), calcium (Ca²⁺), magnesium (Mg²⁺), chloride (Cl⁻), and sulfate (SO₄²⁻) was used to predict TDS as an output parameter. The computed values of TDS by ANN and MLR were in close agreement with their respective measured values. Comparative analysis of ANN and MLR showed that TDS root means square error (RMSE) for city sub-division and Pearson’s coefficient of correlation (r) for ANN and MLR were 2.9% and 0.981 and 4.5% and 0.978, respectively. Similarly, for the Farrukhabad sub-division, RMSE and r for ANN were 4.9% and 0.952, while RMSE and r for MLR were 5.5% and 0.941, respectively. For the Shahadra sub-division, RMSE was 10.8%, r was 0.869 for ANN, RMSE was 11.3%, and r was 0.860 for MLR. The results exhibited that the ANN model showed less error in results than MLR. Therefore, ANN can be employed successfully as a groundwater quality prediction tool for TDS assessment. Full article

Green remediation is essential in the current practice of water resources management. In this study, a series of ozone β-cyclodextrin (O₃-βCD) inclusion complexes were prepared under a selected range of different ozone concentrations, β-CD concentrations, and solution pHs to test their ozone release rates and efficiencies in the treatment of total petroleum hydrocarbons (TPH) in water. The main objectives of this study are to characterize the O₃-βCD system, mathematically model its ozone release rate, and test its capability in the degradation of pollutants. From the results, it was found that by defining a set of dimensionless parameters, including β-CD to ozone molar ratio and various degrees of ozone saturation, the steady-state conditions in the O₃-βCD system can be represented by a newly developed dimensionless plot. In an optimal condition, the dissolved ozone release rate of 6.8 × 10⁻⁵ mM/min can be achieved in the O₃-βCD system. A mathematical model was successfully developed to estimate the ozone release rate. In the TPH removal experiments, the effects of β-CD to ozone molar ratio and ozone dosage on the removal efficiency were rigorously examined. Overall, an optimal TPH removal of nearly 90% can be achieved in the treatment of 50 mg/L of TPH in water using this inclusion complex reagent. Full article

Globally, several hundred thousand hectares of both agricultural and urban land have become contaminated with per- and polyfluoroalkyl substances (PFAS). PFAS compounds are resistant to degradation and are mobile in soil compared to other common contaminants. Many compounds have K_D values (matrix/solution concentration quotients) of <10. PFAS compounds endanger the health of humans and ecosystems by leaching into groundwater, exposure via dust, and, to a lesser extent, through plant uptake. This review aims to determine the feasibility of phytomanagement, the use of plants, and the use of soil conditioners to minimize environmental risk whilst also providing an economic return in the management of PFAS-contaminated land. For most sites, PFAS combinations render phytoextraction, the use of plants to remove PFAS from soil, inviable. In contrast, low Bioaccumulation Coefficients (BAC; plant and soil concentration quotients) timber species or native vegetation may be usefully employed for phytomanagement to limit human/food chain exposure to PFAS. Even with a low BAC, PFAS uptake by crop plants may still exceed food safety standards, and therefore, edible crop plants should be avoided. Despite this limitation, phytomanagement may be the only economically viable option to manage most of this land. Plant species and soil amendments should be chosen with the goal of reducing water flux through the soil, as well as increasing the hydrophobic components in soil that may bind the C-F-dominated tails of PFAS compounds. Soil conditioners such as biochar, with significant hydrophobic components, may mitigate the leaching of PFAS into receiving waters. Future work should focus on the interactions of PFAS with soil microbiota; secondary metabolites such as glomalin may immobilize PFAS in soil. Full article

Membrane distillation (MD) has unique advantages in the treatment of high-salt wastewater because it can make full use of low-grade heat sources. The high salinity mine water in western mining areas of China is rich in Ca²⁺, Mg²⁺, SO₄²⁻ and HCO₃⁻. In the MD process, the inorganic substances in the feed will cause membrane fouling. At the same time, low surface tension organic substances which could be introduced in the mining process will cause irreversible membrane wetting. To improve the anti-fouling and anti-wetting properties of the membrane, the PVDF omniphobic membrane in this paper was prepared by electrospinning. The water contact angle (WCA) can reach 153°. Direct contact membrane distillation (DCMD) was then used for treating high-salinity mine water. The results show that, compared with the unmodified membranes, the flux reduction rate of the omniphobic membrane was reduced by 34% in 20 h, showing good anti-fouling property. More importantly, the omniphobic membrane cannot be wetted easily by the feed containing 0.3 mmol/L SDS. The extended Derjaguin–Landau–Verwey–Overbeek (XDLVO) theory was used to analyze the free energy of the interface interaction between the membrane and pollutants, aiming to show that the omniphobic membrane was more difficult to pollute. The result was consistent with the flux variation in the DCMD process, providing an effective basis for explaining the mechanism of membrane fouling and membrane wetting. Full article

The extensive pattern of economic growth has an inestimable negative impact on the ecological environment, which causes the soil pollution problem to become increasingly prominent. In order to improve the effectiveness and rationality of prevention and control of heavy metal pollution in regional soil, it is necessary to understand the current situation of pollution, identify pollution sources and clarify future pollution risks. In this paper, an industrially developed city in eastern China was taken as the study region. The positive matrix factorization model (PMF) model and Unmix model was applied to identify and apportion the pollution sources of soil potential toxic elements after evaluating the ecological risk of soil potential toxic elements. The PMF model identified six factors, including single source and composite source. The Unmix model also identified six sources, including sources of nature, industrial discharge and traffic emissions. The comparison between the two models showed that Hg and Ni pollution, as well as Cr enrichment in the study region, were related to the industrial discharge from enterprises and factories. Cd pollution was related to traffic emission sources. Cu and Zn pollution were related to the multiple sources mixed with soil parent material, traffic emissions and industrial discharge from electronic enterprises. Pb pollution was related to natural sources (e.g., soil pH) but also to industrial sources (e.g., industrial wastes discharge). Enrichment was related to soil parent material and agricultural inputs. Our study also implies that soil heavy metal pollution or enrichment in the study region was mainly from anthropogenic sources and supplemented by natural sources. Full article

Non aqueous phase liquid (NAPL) pollution exists in porous media such as soil. SVE technology can be used to remove this pollution in soil. However, few domestic and international studies have paid attention to the changes of soil temperature in the field, which we believe can be useful information to optimize the layout of heating wells. In this research we established partial differential equations of soil heat transfer using the COMSOL multi-field coupling tool to simulate the field distribution of the change in soil internal temperature in the process of SVE to obtain the change of effective heating area with time under certain initial heating conditions. At the same time, we used liquid ethylbenzene to represent NAPL pollutants, and designed a simulation of soil temperature field distribution under the movement of liquid ethylbenzene under external pressure. It was found that under the action of Darcy’s velocity field, the utilization efficiency of the SVE system for the heat source was significantly improved, that is, the temperature distribution of the soil was more uniform. However, the temperature of the heated area increased slowly because the extraction well took away the heat energy. The heat source power should be increased or prolonged to improve the effect of Darcy’s field. Through a coupled simulation, we obtained a variation relationship of the soil temperature field in 1800 min under the action of one extraction well and four heating wells. These data will provide the basis for our next step in designing an algorithm to optimize the distribution of heating wells. Full article

The application of organic fertilizer is an important measure for improving the quality of agricultural products and realizing the sustainable development of agriculture. The original small-scale family business model in China is no longer suitable for the development of modern agriculture. Large-scale agricultural business has become the mainstream trend, accompanied by the increasingly active land-transfer market. It is, therefore, necessary to determine whether farmland scale influences farmers’ organic fertilizer applications in China. Based on the analysis of the influence mechanism of farmland scale on farmers’ organic fertilizer application behaviors, empirical tests were conducted using survey data from 812 citrus farmers in Sichuan Province, China. The results show that the large-scale farmers are more likely to apply organic fertilizer and increase the application intensity than small-scale farmers and that the heterogeneity of farmers also affect their organic fertilizer application behavior. The results suggest that the government should encourage farmers to conduct moderate-scale management and promote their application behavior with organic fertilizer by improving awareness, strengthening education and training, and providing financial support. Full article

In this research, Ningbo City, a typical industrial city in southeastern China, was selected as the study area, and the concentrations of 12 heavy metals (Cd, Cr, Ni, Pb, Zn, Cu, Hg, As, Co, V, Se, and Mn) were measured at 248 sampling points. Pollution index methods were used to assess the status of soil heavy metal contamination, and the Positive Matrix Factorization (PMF) model and Unmix model were integrated to identify and apportion the sources of heavy metal contamination. The results indicated that nearly 70% of the study area was polluted by heavy metals, and that Ni, Cr, and Zn were the main enriched heavy metals. The five sources identified using the PMF model were a geological source, an atmospheric deposition source, a transportation emissions source, a mixed source of agriculture and industry, and a mixed source of geology and industry. The four sources identified using the Unmix model were a mixed source of geology, agriculture, and industry (14.27%); a transportation emissions source (4.76%); a geological source (14.7%); and a mixed source of geology and industry (66.28%). These results have practical significance, as they can help to carry out pollution source risk assessment and give priority to the management of pollution source control. Full article

The coastal aquifer La Yarada has anthropogenic and geogenic contamination that adversely affect the quality of groundwater for population and agricultural use. In this scenario, multivariate statistical methods were applied in 20 physicochemical and isotopic parameters of 53 groundwater pumping wells in October 2020, with the aim of characterizing the hydrogeochemical processes that dominate the groundwater of the coastal aquifer and the factors that cause them to optimize the effective management of water resources, delimiting areas affected by more than one salinization process. The samples were grouped into three clusters (C1, C2, and C3) with cluster analysis, the spatial distribution of C2 and C3 (reclassified in stiff diagrams), evidenced hydrogeochemical facies associated with the flow and recharge directions governed by the structural lineaments (NE-SO), favoring some areas more than others, arising different facies and hydrogeochemical processes. Factor analysis was applied from three different approaches: (1) main elements, (2) trace elements, and (3) physicochemical and isotopic parameters; exposing 6 distinguishable hydrogeochemical processes in the aquifer and factors that cause them: (i) salinization—marine intrusion, (ii) fertilizer leaching and dissolution of (Ca²⁺, Mg²⁺), (iii) wastewater mixture (NO³⁻), (iv) reducing conditions (Fe, Mn, Al), (v) contributions of (B, Sr), (vi) conservative mixtures and dissolution (As, F). It was validated with water quality indices (WQI) according to the national limits, delimiting 67 km² parallel to the coast with “bad” to “very bad” quality for human consumption and unsuitable for irrigation according to the Wilcox diagram thus pre-treatment in this area is indispensable. Full article

Legislation addressing the quality of groundwater and increasing concerns over public health calls for the development of analytical methods that can produce accurate and precise results at the ppt level. Passive sampling has been recognised as a helpful tool in identifying various organic pollutants in groundwater, even when their presence had not yet been identified through conventional groundwater quality monitoring. The article presents an analytical method involving a simple and cost-effective passive sampling device using Zorflex^® activated carbon fibres (ACFs) for the qualitative monitoring of a broad range of organic pollutants in water in a single run. The applicability of the method developed was tested in three hydrogeological studies. In the first case, we present a non-targeted qualitative screening and a list of 892 different contaminants detected in the groundwater in Slovenia. In the second case, we discuss the presence and origin of organic compounds in the groundwater from a pilot area of the urban aquifer, Ljubljansko polje. The third case presents a comparison of results between passive and grab sampling. Passive sampling with ACFs confirmed the presence of a pollutant, even when it had not been previously detected through a quantitative method. Full article

In recent decades, due to rapid increases in water demand and greater usage of water for irrigation from surface canals, waterlogging problems have been created in the southwest zone of Punjab, coupled with a stagnation in saline zone formation due to salinity ingression. To understand these salinity issues, the present study has been conducted in three districts (Muktsar, Fazilka, and Faridkot) of Punjab to understand the root cause. To this end, groundwater samples were collected from 142 piezometers developed at 40 sites. Electrical conductivity (EC) observations were taken in the field, and collected samples were analyzed for isotopes in the laboratory. Results found that salinity in groundwater arises from the combination of evaporation enrichment and salt dissolution. The dissolved salts may be acquired due to salts from aquifer materials or salts from surface soils dissolving and leaching down with the recharging water. Besides, the zone of interaction is mapped using stable isotopic composition. The study suggests that zone of interaction between aquifers can be effectively used in groundwater augmentation, management, and contamination control at regional and/or global scales to curb water demand in the future. Full article