Constr. Mater., Volume 6, Issue 2 (April 2026) – 8 articles

This study investigates the pullout behaviour of hooked-end superelastic shape memory alloy (SMA) fibres embedded in concrete with the aim to develop an analytical model. Single fibre pullout experiments were performed to evaluate the mechanical response of SMA fibres with various hook geometries. A mathematical model based on the friction pulley method was then developed to predict the experimental pullout load versus displacement plots. The model integrates the tensile stress–strain response and the elastic–plastic constitutive behaviour of superelastic SMA materials, while also accounting for fibre slip and superelastic deformation during the pullout process. The pullout process is modelled through staged mechanisms including elastic response and debonding, progressive mechanical anchorage, and frictional pullout. The contribution of mechanical anchorage is governed by the elastic–superelastic strain distribution within the hook bends. The proposed model reasonably reproduces the overall load-slip response, peak pullout load, slip at peak load, and pullout energy for the three different fibre geometries extracted from normal strength and high-performance concrete matrix. The proposed mathematical model offers a transferable and predictive tool for assessing the pullout performance of hooked-end SMA fibres and supports their integration into design of SMA fibre-reinforced cementitious composites. Full article

The depletion of natural aggregates and the rapid increase in construction and demolition waste have intensified the need for sustainable structural materials. Recycled aggregates (RAs) represent a promising alternative; however, their performance under elevated temperatures remains insufficiently investigated. This study examines the combined influence of recycled coarse and fine aggregates (RCFA) replacement ratios and fire exposure on the shear behavior of RC beams. Five replacement levels (0%, 25%, 50%, 75%, and 100%) were considered. A total of forty-five beams (1500 × 150 × 200 mm) were tested at 23 °C, 400 °C, and 600 °C. In addition, a finite element model was developed to validate the experimental findings. The results showed at 23 °C, increasing the RA content led to a moderate reduction in the ultimate shear capacity of approximately 6–10%. Fire exposure significantly aggravated strength degradation, with additional reductions of up to 11% at 400 °C and total losses reaching about 22% at 600 °C compared to the control beam at room temperature. Stiffness deterioration and crack propagation became more pronounced with higher temperatures and replacement ratios due to thermal damage to the cement matrix and interfacial transition zones. Nevertheless, moderate replacement levels (25–50%) maintained acceptable residual shear capacity and improved ductility and energy absorption. Numerical predictions closely matched experimental results, with load differences within 1–5%, confirming the model’s reliability. Full article

Construction materials are the primary source of embodied carbon in long-span bridge projects, particularly for steel-intensive structures. This study presents an empirical construction-stage carbon footprint assessment of the Anhsin Bridge, an asymmetric cable-stayed steel truss bridge in Taiwan. Using the emission factor method in accordance with ISO 14067 and Taiwan Environmental Protection Administration guidelines, a cradle-to-gate (A1–A5 equivalent) system boundary was applied, covering material production, transportation, and on-site construction activities. Total construction-stage emissions were estimated at 55,349 tCO₂e, dominated by structural steel (51.8%), followed by reinforcing steel, concrete, and cement. Material-related emissions accounted for over 90% of the total, highlighting the critical role of material selection in embodied carbon reduction. Three practical mitigation strategies were evaluated using verified project data, as follows: 40% cement substitution with supplementary cementitious materials, optimized steel erection methods, and enhanced reuse of formwork and temporary works. The combined scenario achieved a 7.3% reduction in construction-stage emissions without compromising constructability. The findings demonstrate the effectiveness of material-oriented, constructability-aware strategies for reducing embodied carbon in steel-intensive bridge construction. Full article

Fiber-reinforced concrete has proved to be viable in improving the mechanical characteristics of structural elements to the flexural and shear stresses. The concrete cubes, prisms, and cylinders were standardized, cast and cured after 28 days to assess the baseline mechanical characteristics. Beam specimens were made of different types of fibers, lengths, and different volumetric contents and then subjected to controlled shear tests in which the crack initiation, propagation, and deformation were accurately measured. The experimental data proved that the addition of fibers was highly beneficial in terms of the mechanical performance of concrete. Basalt fibers enhanced compressive strength by up to 20.8 percent and tensile strength by 30.8 percent, whereas steel fibers had the best flexural strength with a maximum compressive and bending strength of 47.2 MPa and 6.56 MPa, respectively, at optimum dosage. Polypropylene fibers also improved performance, but in a lesser manner. The fiber addition served well to reduce the width of cracks and retard crack propagation, thus enhancing load-bearing capacity. These results show that dispersed fiber reinforcement that uses steel and basalt fibers is a practical solution to improving the dispersion of concrete in terms of durability and load-bearing capacity. The research will help guide the selection of fiber and the content in the reinforced concrete work to offer more robust and sustainable solutions to building. Full article

Tire-Derived Aggregate (TDA) is a recycled fill material made by cutting scrap tires into small pieces that satisfy the gradation requirements in ASTM D 6270. Since its introduction to civil engineering applications, TDA fill and TDA backfill have been successfully implemented in many projects. However, the dynamic behavior of the TDA backfill under significant earthquakes has not been substantially addressed. The present study used nonlinear time-history Finite Element Analysis (FEA) to analyze the dynamic behavior of a retaining wall with TDA backfill captured from the full-scale shake table test. Unlike typical soil failure observed in a similar retaining wall with conventional soil backfill, significant wall sliding occurred because lightweight TDA contributed to reducing the friction resistance of the wall footing. Therefore, the analysis required modeling capability of rigid body motion and impact loading from the separation between the wall stem and the backfill. With adequate friction models and softened contact models, the FEA generated the dynamic motion of the retaining wall that matched well with the measured responses, including the wall sliding. The friction model between the wall footing and soil was most critical in accurately reproducing wall sliding motion. It was determined to use different friction coefficients for the two different earthquakes used in the study in order to simplify the rate dependence of the coefficient. Also, the softened contact model generated more reasonable impact force by allowing overclosure and finite stiffness during impact. The FEA model and modeling technique in the present study can be used for the seismic design of various field-scale retaining walls with TDA backfill. Full article

In recent decades, the need to embrace the concepts of the circular economy and ecological transition has become increasingly apparent, especially in the civil engineering sector. This research aims to study a Cement-Bound Granular Material (CBGM) pavement layer using the industrial by-product Anhydrous Calcium Sulphate (ACS) as a partial replacement for Portland Cement (PC) by weight. The dual objective is to reduce environmental impact and ensure long-term high mechanical performance. Mechanical tests conducted at different curing periods (7, 28, 96, and 120 days) showed compressive strength gains of up to 180%. The evolution of the mechanical behavior was correlated with the formation of the gypsum dihydrate and ettringite hydrated phases, found by quantitative XRD analysis, to reinforce the cement matrix. Finite element simulations and fatigue life predictions using Miner’s rule over pavement lifespans of 15, 20, and 30 years indicated an increase in durability by a factor of 4.68 for the ACS-enhanced mixture compared to traditional PC-only formulations. Leaching tests show the material performs within acceptable environmental thresholds, even if its classification and acceptance may differ across regulatory systems, suggesting a solid basis for its application in sustainable practices. Full article

Concrete remains one of the most widely utilized construction materials, valued particularly for its exceptional compressive strength. However, exposure to fire can compromise both its internal microstructure and external integrity. This research investigates the behavior of concrete manufactured with recycled concrete coarse aggregate (RCA) derived from construction waste, aiming to establish experimental evidence of fire’s impact on compressive strength. We employed the Optimal Density Method to design mix proportions targeting 24 MPa compressive strength. The experimental program comprised 45 cylindrical samples distributed across three replacement levels: 0%, 15%, and 30% natural aggregate substitution with RCA. Following 28 days of curing, samples underwent direct fire exposure in a melting furnace. Temperature progression was monitored using a pyrometer, ranging from ambient (0 °C) through 250 °C, 400 °C, 600 °C, to 800 °C, with controlled exposure duration at each level. Three samples were tested at each temperature. After fire exposure, samples were cooled for 24 h at ambient temperature before compression testing. The densities of the fresh specimens were determined to be 2254.06 kg/m³ for HS-0AR%, 2210.09 kg/m³ for HS-15AR%, and 2180.85 kg/m³ for HS-30AR%, with a percentage density variation with respect to HS-0AR% of 1.95% and 3.25%, respectively. Finally, in relation to the compressive strength of concrete, a reduction of 4.34% was observed for 15% AGR and 5.72% for 30%, suggesting that the variations may be due to factors such as the water/cement ratio, the quality of the aggregate, and the curing conditions of concrete. In addition, several pathologies were observed, such as cracking, fissures, color changes, and spalling. Full article

The ongoing concern about sustainable infrastructure has driven the development of cement-based adhesives (CBAs) for fibre-reinforced polymer (FRP)-based concrete retrofitting. Nevertheless, traditional CBAs usually have low bond strength, low crack resistance, and low long-term durability that undermine the performance of FRP–concrete systems. To address these limitations, this focused review examines the potential of nanomaterial-modified CBAs to enhance interfacial bond behaviour and overall structural performance. A systematic assessment of recent experimental studies was used to analyze CBAs modified with nanosilica, carbon nanotubes, graphene oxide, and other nanomaterials. The roles of these nanomaterials in improving adhesion mechanisms, stress transfer efficiency, crack control, and resistance to environmental stressors are critically discussed. We also contrast the performance of neat and nano-modified CBAs in FRP-based retrofitting systems, with particular emphasis on bond behaviour, mechanical response, and durability-related performance. Particular emphasis is put on innovative high-strength self-compacting cementitious adhesives (IHSSC-CAs), which are identified as an emerging class of sustainable bonding materials combining high mechanical performance with improved environmental compatibility in relation to traditional bonding systems. The paper concludes with the identification of key research gaps, a discussion of practical implementation challenges, and an outline of future research directions for the development of next-generation sustainable and resilient concrete retrofitting technologies. Full article