Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
3.7
2.5
Journals
Dentistry Journal
Special Issues
3D Printing and Restorative Dentistry
share announcement

3D Printing and Restorative Dentistry

A special issue of Dentistry Journal (ISSN 2304-6767). This special issue belongs to the section "Restorative Dentistry and Traumatology".

Deadline for manuscript submissions: 10 February 2025 | Viewed by 6055

Special Issue Editor

Prof. Dr. Neamat Hassan Abubakr

E-Mail Website
Guest Editor
Department of Biomedical Sciences, School of Dental Medicine, University of Nevada, Las Vegas, NV 89106, USA
Interests: dental material; restorative dentistry; dental pain; dental anxiety; clinical trials
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

By proposing new designs and fabrications of dental prostheses, 3D printing has modernized the field of restorative dentistry. The advent of 3D printing has led to the development of new materials and techniques that will be utilized to advance restorative dentistry. Using biocompatible and bioactive materials promotes tissue regeneration and enhances the long-term success of dental restorations.

Furthermore, 3D printing technology improves dental restorations’ quality by fabricating restorations with improved accuracy, fit, and aesthetics. This process has created opportunities for creating cost-effective complex restorations.

The future of restorative dentistry will continue to be shaped by 3D printing, increasing the number of treatment options and expanding the capabilities of dental professionals.

Prof. Dr. Neamat Hassan Abubakr
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Dentistry Journal is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2000 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • 3D printing
  • 3D printed crowns
  • 3D printed dentures
  • 3D printed dental implants surgical guides
  • 3D printed retainers

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (3 papers)

Download All Papers
Order results
Result details
Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:

Research

Jump to: Other

12 pages, 3243 KiB  
Article
The Influence of Dental Virtualization, Restoration Types, and Placement Angles on the Trueness and Contact Space in 3D-Printed Crowns: A Comprehensive Exploration
by Tsung-Yueh Lu, Wei-Chun Lin, Tzu-Hsuan Yang, Citra Dewi Sahrir, Yung-Kang Shen and Sheng-Wei Feng
Dent. J. 2024, 12(1), 2; https://doi.org/10.3390/dj12010002 - 19 Dec 2023
Cited by 4 | Viewed by 2168
Abstract
The current digital dentistry workflow has streamlined dental restoration production, but the effectiveness of digital virtual design and 3D printing for restorations still needs evaluation. This study explores the impact of model-free digital design and 3D-printing placement angles on restorations, including single crowns [...] Read more.
The current digital dentistry workflow has streamlined dental restoration production, but the effectiveness of digital virtual design and 3D printing for restorations still needs evaluation. This study explores the impact of model-free digital design and 3D-printing placement angles on restorations, including single crowns and long bridges produced with and without casts. The restorations are 3D printed using resin at placement angles of 0°, 60°, and 90°. Each group of samples was replicated ten times, resulting in a total of 120 restorations. The Root Mean Square Error (RMSE) value was used to evaluate the surface integrity of the restoration. In addition, the contact space, edge gap, and occlusal space of restorations produced by different processes were recorded. The results indicate that there was no significant difference in the RMSE value of the crown group (p > 0.05). Changing the bridge restoration angle from 0° to 90° resulted in RMSE values increasing by 2.02 times (without casts) and 2.39 times (with casts). Furthermore, the marginal gaps in the crown group were all less than 60 μm, indicating good adaptation. In contrast, the bridge group showed a significant increase in marginal gaps at higher placement angles (p > 0.05). Based on the findings, virtual fabrication without casts does not compromise the accuracy of dental restorations. When the position of the long bridge exceeds 60 degrees, the error will increase. Therefore, designs without casts and parallel placement result in higher accuracy for dental restorations. Full article
(This article belongs to the Special Issue 3D Printing and Restorative Dentistry)
►▼ Show Figures

Graphical abstract

31 pages, 8205 KiB  
Article
Ranking Technologies of Additive Manufacturing of Removable Complete Dentures by the Results of Their Mechanical Testing
by Dmitry I. Grachev, Igor V. Zolotnitsky, Dmitry Yu. Stepanov, Alexander A. Kozulin, Magomet Sh. Mustafaev, Aslan V. Deshev, Dmitriy S. Arutyunov, Islam V. Tlupov, Sergey V. Panin and Sergey D. Arutyunov
Dent. J. 2023, 11(11), 265; https://doi.org/10.3390/dj11110265 - 13 Nov 2023
Cited by 5 | Viewed by 2248
Abstract
In this study, a methodology was developed for ranking manufacturing technologies of removable complete dentures (RCDs) according to the results of their full-scale mechanical tests. The actuality of the study is motivated by establishing the advantages and drawbacks of 3D-printed RCDs in contrast [...] Read more.
In this study, a methodology was developed for ranking manufacturing technologies of removable complete dentures (RCDs) according to the results of their full-scale mechanical tests. The actuality of the study is motivated by establishing the advantages and drawbacks of 3D-printed RCDs in contrast with ones manufactured via an analog protocol. The RCDs were fabricated via four technological routes that included various combinations of subtractive technologies (hot polymerization/HP and CAD/CAM milling) and additive manufacturing (digital light processing/DLP) ones and the installation of commercially available cosmetic denture teeth (DT). In the mechanical tests, different blocks of teeth (incisors, canines, premolars and molars) were loaded. To solve the ranking problem, it was proposed to interpret the results of the mechanical tests in terms of the reliability, durability and compliance/stiffness criteria. For this purpose, the combined AHP-VIKOR method was applied. In addition, a computer simulation of the mechanical loading conditions and the response of the RCDs was performed based on the finite element method (FEM). As the key conclusion, it was stated that additive manufacturing (AM) methods are competitive and cost-effective techniques for the fabrication of RCDs. Full article
(This article belongs to the Special Issue 3D Printing and Restorative Dentistry)
►▼ Show Figures

Figure 1

Other

Jump to: Research

13 pages, 5037 KiB  
Case Report
Three Dimensional-Printed Gingivectomy and Tooth Reduction Guides Prior Ceramic Restorations: A Case Report
by Carlos A. Jurado, Jose Villalobos-Tinoco, Mark A. Lackey, Silvia Rojas-Rueda, Manuel Robles and Akimasa Tsujimoto
Dent. J. 2024, 12(8), 245; https://doi.org/10.3390/dj12080245 - 1 Aug 2024
Cited by 1 | Viewed by 1025
Abstract
Computer-aided design and computer-aided manufacturing (CAD/CAM) dentistry have significantly changed workflows in recent years. Restorations and devices can now be digitally designed and 3D-printed for dental care purposes. This clinical case report provides straightforward protocols for the digital design and 3D manufacture of [...] Read more.
Computer-aided design and computer-aided manufacturing (CAD/CAM) dentistry have significantly changed workflows in recent years. Restorations and devices can now be digitally designed and 3D-printed for dental care purposes. This clinical case report provides straightforward protocols for the digital design and 3D manufacture of gingivectomy and tooth preparation guides. These types of guides improved the gingival architecture of the anterior teeth and provided controllable tooth preparations prior to labial ceramic veneers. Thoughtful clinical evaluation started with listening to the patient’s chief complaint and extra- and intra-oral evaluations. Then a digital wax-up was performed, followed by an intra-oral mock-up, to evaluate the shape of the proposed restorations. After patient acceptance, the clinical procedure started with the gingivectomy and tooth preparation. Hand-crafted porcelain veneers were bonded under rubber dam isolation to avoid any contamination and maximize the bonding protocol. The esthetic and functional demands were fully satisfied. Predictable outcomes can be obtained whenever a meticulous evaluation and execution of all the steps are performed. Three dimensional printing technology allows the fabrication of devices such as gingivectomy and tooth reduction guides that help accomplish the desired results. Full article
(This article belongs to the Special Issue 3D Printing and Restorative Dentistry)
►▼ Show Figures

Figure 1

Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:
 
Displaying articles 1-3
Back to TopTop