Search Results (13)

Graphene nanoplatelet aggregates (GNAs) are a low-cost, low-quality alternative to graphene nanoplatelets (GNPs), characterized by their three-dimensional stacked structure and porous surface morphology. Despite their affordability, limited research has been conducted on the effects of GNAs in cementitious systems. This study investigates the impact of GNAs on hydration kinetics, phase assemblage, mortar consistency, mechanical strength, bulk electrical resistivity, water absorption, and pore solution pH. Mortar mixtures with 0%, 0.05%, and 1% GNAs by cement weight were prepared using a water-to-cement ratio of 0.42 and cured for 28 days. The results showed that GNAs had minimal influence on hydration kinetics, with no significant changes in hydration products detected by XRD and TGA analyses. Mortar consistency consistently decreased with increasing GNA content. At 0.05%, GNAs had no significant effect on compressive strength or bulk electrical resistivity, whereas 1% GNAs reduced compressive strength by 10%. Water absorption was significantly lower in specimens with 1% GNAs as well, while pore solution pH increased at this dosage. The findings of this study indicate that the incorporation of GNAs at a 0.05% replacement level does not inherently enhance cementitious properties but can influence specific behaviors, such as workability and water absorption, when used at 1% dosages. Full article

Graphene has been considered an ideal reinforcement in aluminum alloys with its high Young’s modulus and fracture strength, which greatly expands the application range of aluminum alloys. However, the dispersion of graphene and the interfacial reaction between graphene and the aluminum matrix limit its application due to elevated temperature. Friction stirring processing (FSP) is regarded as a promising technique to prepare metal matrix composites at lower temperatures. In this paper, FSP was used to prepare graphene-nanoplates-reinforced aluminum composites (GNPs/Al). The corresponding effects of the process parameters and graphene content on GNPs/Al were thoroughly studied. The results showed that plastic strain, heat input, and graphene content were the key influencing factors. Large degrees of plastic strain can enhance the dispersion of graphene by increasing the number of stirring passes and the ratio of stirring to welding velocity, thereby improving the strength of GNPs/Al. Low heat input restricts the plastic flow of graphene in the matrix, whereas excessive heat input can promote interfacial reactions and lead to the formation of a more brittle phase, Al₄C₃. This is primarily associated with the stirring velocity and welding velocity. High graphene content levels can improve the material strength by refining the grain size, improving the load transfer ability, and acting as a precipitate to prevent dislocation movement. These findings make a contribution to the development of advanced aluminum alloys with graphene reinforcement, offering broader application potential in industries. Full article

Over the past few years, polymer nanocomposites have garnered a significant amount of interest from both the scientific community and industry due to their remarkable versatility and wide range of potential uses in various fields, including automotive, electronics, medicine, textiles and environmental applications. In this regard, this study focuses on the influence of a compatibilizer rubber on a nanocomposite incorporating graphene nanoparticles (GNPs), with a polymer matrix based on a blend of polypropylene (PP) and polyethylene terephthalate (PET). This effect has been investigated on both isotropic samples and on anisotropic/spun fiber samples. The influence of the compatibilizer rubber on morphological, rheological and mechanical properties was analysed and discussed. Mechanical and morphological properties were evaluated on both isotropic samples obtained by compression moulding and melt-spun fibers. The addition of the rubbery compatibilizer increased the viscosity, improving interfacial adhesion, and the same effect was observed for the melt strength and breaking stretching ratios. Mechanical properties, including the elastic modulus, tensile strength and elongation at break, improved in both types of samples but more significantly in the fibers. These improvements were attributed to the orientation of the matrix, the formation of PET microfibrils, and the reduction in the size of graphene nanoparticles due to the action of the elongational flow. This reduction, facilitated by the elongation flow and the action of the compatibilizer, improved matrix–nanofiller adhesion due to the increased contact area between the two polymeric phases and between the filler and matrix. Finally, a transition from brittle to ductile behaviour was observed, particularly in the system with the compatibilizer, attributed to defect reduction and improved stress transmission. Full article

Graphene nanoplatelets (GNPs)/epoxy composites have been fabricated via gravity molding. The electrical and thermal properties of the composites have been studied with variable GNP type (C300, C500, and C750, whose surface areas are ~300, 500, and 750 m²/g, respectively), GNP loading (5, 10, 12, and 15 wt.%), and dispersion time via ultrasonication (0, 30, 60, and 120 min). By increasing the time of sonication of the GNP into the epoxy matrix, the electrical conductivity decreases, which is an effect of GNP fragmentation. The best results were observed with 10–12% loading and a higher surface area (C750), as they provide higher electrical conductivity, thereby preserving thermal conductivity. The influence of sonication over electrical conductivity was further analyzed via the study of the composite morphology by means of Raman spectroscopy and X-ray diffraction (XRD), providing information about the aspect ratio of GNPs. Moreover, electromagnetic shielding (EMI) has been studied up to 4 GHz. Composites with C750 and 120 min ultrasonication show the best performance in EMI shielding, influenced by their higher electrical conductivity. Full article

The proposed strategy for the extrusion of printable composite filaments follows the favourable association of biogenic hydroxyapatite (HA) and graphene nanoplatelets (GNP) as reinforcement materials for a poly(lactic acid) (PLA) matrix. HA particles were chosen in the <40 μm range, while GNP were selected in the micrometric range. During the melt–mixing incorporation into the PLA matrix, both reinforcement ratios were simultaneously modulated for the first time at different increments. Cylindrical composite pellets/test samples were obtained only for the mechanical and wettability behaviour evaluation. The Fourier-transformed infrared spectroscopy depicted two levels of overlapping structures due to the solid molecular bond between all materials. Scanning electron microscopy and surface wettability and mechanical evaluations vouched for the (1) uniform/homogenous dispersion/embedding of HA particles up to the highest HA/GNP ratio, (2) physical adhesion at the HA-PLA interface due to the HA particles’ porosity, (3) HA-GNP bonding, and (4) PLA-GNP synergy based on GNP complete exfoliation and dispersion into the matrix. Full article

Ultrasonic welding (UW) is a well-established technique for joining thermoplastic composites and has recently been utilized in the aerospace and automotive industries. In the case of thermoset composites (TSCs), a polymer-based material placed at the welding interface called an energy director (ED) is required. The choice of the coupling layer material is linked to several requirements, such as processing temperature, high adhesion to the thermoset composites (TSCs) adherend and mechanical strength of the resulting welded joints. In this work, the authors investigated the possibility of using Poly-vinyl-butyral (PVB) reinforced with graphite nanoplatelets (GNPs) as a coupling layer in the UW of TSC adherents. The effect of GNPs aspect ratio and content on the weldability of carbon fiber-reinforced plastics (CFRP) has been investigated. PVB/GNPs nanocomposites with different filler contents (from 0.5 wt% to 2 wt%) and different aspect ratios (100 and 2100) have been fabricated. The influence of the viscoelastic properties of the flat EDs on weldability has been assessed. Finally, an improvement of lap shear strength (LSS) of 80% was found for nanocomposites with 0.5 wt% of high-aspect-ratio GNPs with respect to neat PVB. The use of high damping nanocomposites as coupling materials for TSCs paves the way for a new generation of EDs in UW. Full article

One of the biggest problems facing the use of carbon nanotubes in reinforced composites is agglomeration within the matrix phase. This phenomenon—caused by Van der Waals forces—leads to dispersion problems and weakens the properties of the composites. This research presents a multi-stage homogenization approach used to investigate the influence of the aspect ratio, volume fraction, and agglomeration of the nanofillers on the effective mechanical properties of a polymer biocomposite containing randomly dispersed carbon nanotubes and graphene nanoplatelets. The first stage consisted in evaluating the properties of the reinforced polymers by the CNT/GNP. The second step consisted in combining the reinforced polymers with different natural and synthetic unidirectionally oriented fibers. It was found that agglomeration has a huge influence on the mechanical properties of the composite. The novelty of this work consisted of the consideration of the parameters influencing the elastic properties using different micromechanics approaches and numerical techniques. Full article

Rocket kerosene plays an important role in the regenerative cooling process of rocket thrust chambers. Its thermal conductivity determines the cooling efficiency and the tendency to coke in rocket kerosene engines. In this paper, graphene nanoplatelets (GNPs) were introduced into rocket kerosene to improve its thermal conductivity. Molecular dynamics simulation was used to investigate the thermal conductivity of the composite system and its underlying thermal conductivity mechanism. Firstly, by studying the effect of the mass fraction of GNPs, it was found that, when the graphene mass fraction increases from 1.14% to 6.49%, the thermal conductivity of the composite system increases from 4.26% to 17.83%, which can be explained by the percolation theory. Secondly, the influence of the size of GNPs on the thermal conductivity of the composite system was studied. Basically, the thermal conductivity was found to increase by increasing the aspect ratio of GNPs, indicating that GNPs with a higher aspect ratio are more conducive to improving the thermal conductivity of rocket kerosene. By carefully analyzing the effect of the size of GNPs on thermal conductivity, it was concluded that the thermal conduction enhancement by adding GNPs is determined by the combined effect of the percolation theory and the Brownian motion. The results of the temperature effect study showed that the ratio of thermal conductivity to rocket kerosene increased from 1.16 to 1.26 and from 1.07 to 1.11 for the composite systems, with graphene sizes of 41.18 Å × 64.00 Å and 24.14 Å × 17.22 Å in the temperature range of 293 K to 343 K, respectively. It is further proved that the Brownian motion of GNPs has a non-negligible effect on the thermal conductivity of the composite system. This work provides microscopic insights into the thermal conduction mechanism of GNPs in nanofluids and will offer practical guidance for improving the thermal conductivity of rocket kerosene. Full article

The monotonic and cyclic properties of carbon fiber-reinforced epoxy (CFEP) laminate specimens with matrices modified by multiwalled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) were experimentally studied. The laminate specimens were fabricated by the hand lay-up procedure and six MWCNT:GNP weight ratios, i.e., 0:0, 10:0, 0:10, 5:5, 9:1, and 1:9, were considered to prepare the nanoparticle-modified epoxy resin by using an ultrasonic homogenizer and a planetary centrifugal mixer. Then, these laminate specimens with their matrices modified under various nanofiller ratios were employed to investigate the influence of the number of nanofiller types and hybrid nanofiller ratios on the quasi-static strength, fatigue strength, and mode I fracture toughness. The experimental results show that adding individual types of nanoparticles has a slight influence on the quasi-static and fatigue strengths of the CFEP laminates. However, the remarkable synergistic effect of MWCNTs and GNPs on the studied mechanical properties of the CFEP laminates with matrices reinforced by hybrid nanoparticles has been observed. Examining the evolution of stiffness-based degradation indicates that adding hybrid nanoparticles to the matrix can reduce the degradation effectively. The high experimental data of the mode I fracture toughness of hybrid nano-CFEP laminates demonstrate that embedding hybrid nanoparticles in the matrix is beneficial to the interlaminar properties, further improving the fatigue strength. The pushout mechanism of the MWCNTs and the crack deflection effect of the GNPs suppress the growth and linkage of microcracks in the matrix. Furthermore, the bridging effect of the nanoparticles at the fiber/matrix interface retards the interfacial debonding, further improving the resistance to delamination propagation. Full article

The impact on the mechanical properties of an epoxy resin reinforced with pristine graphene nanoplatelets (GNP), highly concentrated graphene oxide (GO), and functionalized graphene oxide (FGO) has been investigated in this study. Molecular dynamics (MD) using a reactive force field (ReaxFF) has been employed in predicting the effective mechanical properties of the interphase region of the three nanocomposite materials at the nanoscale level. A systematic computational approach to simulate the reinforcing nanoplatelets and probe their influence on the mechanical properties of the epoxy matrix is established. The modeling results indicate a significant degradation of the in-plane elastic Young’s (decreased by ~89%) and shear (decreased by ~72.5%) moduli of the nanocomposite when introducing large amounts of oxygen and functional groups to the robust sp² structure of the GNP. However, the wrinkled morphology of GO and FGO improves the nanoplatelet-matrix interlocking mechanism, which produces a significant improvement in the out-of-plane shear modulus (increased by 2 orders of magnitudes). The influence of the nanoplatelet content and aspect ratio on the mechanical response of the nanocomposites has also been determined in this study. Generally, the predicted mechanical response of the bulk nanocomposite materials demonstrates an improvement with increasing nanoplatelet content and aspect ratio. The results show good agreement with experimental data available from the literature. Full article

The influence of manufacturing parameters of filament extrusion and extrusion-based Additive Manufacturing (AM), as well as different post processing techniques, on the electrical conductivity of 3D printed parts of graphene nanoplatelets (GNP)-reinforced acrylonitrile butadiene styrene (ABS) has been analyzed. The key role of the manufacturing parameters to obtain electrically conductive filaments and 3D printed parts has been demonstrated. Results have shown that an increase in extrusion speed, as well as lower land lengths, induces higher extrudate swelling, with the consequent reduction of the electrical conductivity. Additionally, filaments with lower diameter values, which result in a higher surface-to-cross-section ratio, have considerably lower electrical conductivities. These factors tune the values of the volume and surface electrical conductivity between 10⁻⁴–10⁰ S/m and 10⁻⁸–10⁻³ S/sq, respectively. The volume and surface electrical conductivity considerably diminished after 3D printing. They increased when using higher printing layer thickness and width and were ranging between 10⁻⁷–10⁻⁴ S/m and 10⁻⁸–10⁻⁵ S/sq, respectively. This is attributed to the higher cross section area of the individual printed lines. The effect of different post processing (acetone vapor polishing, plasma and neosanding, which is a novel finishing process) on 3D printed parts in morphology and surface electrical conductivity was also analyzed. Full article

The synergetic effect of adding multi-walled carbon nanotubes (MWCNTs) and graphene nanoplatelets (GNPs) on the thermomechanical properties and electric resistance of epoxy polymers were experimentally analyzed in this study. The total content of two employed carbon fillers were kept constant at 0.4 wt %, and seven filler ratios between two fillers (MWCNTs:GNPs), i.e., 10:0, 1:9, 3:7, 5:5, 7:3, 9:1, and 0:10, were considered in the experimental program to investigate the influences of employed nano-filler ratios on the viscoelastic and electrical properties of the studied nanocomposites. The thermomechanical properties and the sheet resistance of the nanocomposites were analyzed using a dynamic mechanical analyzer and four-point probe, respectively. Moreover, the thermogravimetric analyzer was utilized to measure the pyrolysis temperature of the nanocomposites. Experimental results show that the synergistic effect of adding two nano-fillers were clear for the improvement of the storage moduli, glass transition temperatures, and electric conductivity. Oppositely, the employment of two fillers has a slight effect on the pyrolysis temperatures of the studied nanocomposites. The composites with the MWCNT:GNP ratio of 1:9 display the most apparent enhancement of the thermomechanical properties. The improvement results from the uniform distribution and the high aspect ratio of GNPs. The addition of a small amount of MWCNTs provides more linkage in the matrix. Moreover, the specimens with the MWCNT:GNP ratio of 1:9 shows remarkable electrical properties, which result from the large contact surface areas of GNPs with each other. The employment of few MWCNTs plays an important bridging role between the layered GNPs. Full article

The machinability of graphene-reinforced magnesium-based hybrid nanocomposites produced through the application of powder metallurgy method has not been completely reported. This article presents an experimental investigation on the thrust force, the surface roughness (R_a), and drilled surfaces characteristics in the drilling process of a Mg/SiC/GNPs (magnesium matrix based silicon carbide and graphene nanoplatelets) hybrid magnesium matrix composite. The hybrid composite material was produced through the application of a powder metallurgy method. The experiments were carried out with uncoated, PVD (Physical Vapor Deposition), and CVD (Chemical Vapor Deposition) coated tungsten carbide drill bits at three levels of cutting speeds (30, 40, and 50 m/min), and three different levels of feed rate (0.10, 0.15, and 0.20 mm/rev) under dry machining conditions. Taguchi’s L₂₇ (3³) orthogonal array and S/N ratio were used to optimize the optimal parameters for thrust force and surface roughness. The experimental results indicated that the thrust force and the surface roughness were extremely dependent on a particular type of drill bits, feed rate, and cutting speed. The feed rate parameter is known to have a significant influence on the surface finish. Full article