Search Results (91)

Lithium iron phosphate (LFP) batteries have become a popular choice for energy storage, electrified mobility, and plants. All lithium-based batteries produce flammable vent gas as a result of failure through thermal runaway. LFP cells produce less gas by volume than nickel-based cells, but the composition of this gas most often contains less carbon dioxide and more hydrogen. However, when LFP cells fail, they generate lower temperatures, so the vent gas is rarely ignited. Therefore, the hazard presented by a LFP cell in thermal runaway is less of a direct battery fire hazard but more of a flammable gas source hazard. This research identified the constituents and components of the vent gas for different sized LFP prismatic cells when overcharged to failure. This data was used to calculate the maximum homogenous concentration of gas that would be released into a 1.73 m³ test rig and the percentage of the lower explosive limit (LEL). Overcharge experiments were conducted using the same type of cells in the test rig in the presence of remote ignition sources. Ignition and deflagration of the vent gas were possible at concentrations below the theoretical LEL of the vent gas if it was homogeneously mixed. Full article

This research investigates the use of a fiber optic sensor for detecting hydrogen gas during a thermal runaway of lithium-ion batteries (LIBs). Timely detection of thermal runaway in LIBs, particularly in storage and logistics, is crucial for effective safety management and preventing the escalation of incidents to adjacent cells. The sensors employed in this study utilize fiber Bragg grating (FBG) technology. The FBG sensors are coated with palladium nanoparticles, enabling the detection of hydrogen concentrations up to 5%. In abuse tests, the sensors successfully identified hydrogen emissions. Cross-sensitivity effects were observed during a secondary test and were thoroughly investigated. These interferences were found to be primarily caused by carbon monoxide (CO), a common byproduct of battery venting. While the presence of CO can interfere with hydrogen detection, both signals remain independently valuable as indicators of cell malfunction. This dual-response behavior enhances the robustness of fault detection under real-world battery failure scenarios. Full article

In this study, the effect of lithium plating (LP) on the thermal properties of lithium-ion batteries (LIBs) was investigated. A large-format pouch 64.6 Ah cell with a graphite-SiO_x/NMC chemistry was artificially aged (AA_LP) in the laboratory under specific conditions to induce LP on the anode. For thermal behavior analysis, temperature ramp experiments were conducted in a nitrogen-filled steel container on the cycled cell, as well as on fresh and real-life aged cells with the same specifications. Characteristic temperatures, such as first venting and safety critical temperatures, were monitored; additionally, the exhaust gas composition was analyzed using Fourier transform infrared spectroscopy (FTIR) and gas chromatography. It was revealed that the voltage decay of the cells started well before any safety-critical temperature, and the first venting of the AA_LP cell was significantly reduced to 112 °C in comparison to the fresh and real-life aged cells, in which it occurred at 130 °C and 134 °C, respectively. The earlier venting of the AA_LP cell was attributed to the reaction of the plated metallic lithium and the electrolyte. The safety-critical temperature rate (>10 °C/min) occurred at 160.9 °C for AA_LP and at around 159.1 °C for the fresh and real-life aged cells. The maximum temperatures reached were 616 °C, 553 °C, and 566 °C for the fresh, real-life aged, and AA_LP cells, respectively. No significant difference was observed in the exhaust gas after the thermal runaway for the tested cells. Full article

In this study, cells with three different cell chemistries Na₃V₂(PO₄)₂F₃ (NVPF), LiNi_0.6Mn_0.2Co_0.2O₂ (NMC) and LiFePO₄ (LFP) are analyzed in exactly the same setup to compare the hazardous vent gases and their thermal behavior during thermal runaway (TR). Additionally, the influence of different triggers on the failure behavior of NVPF cells is elucidated. The innovative perspective is providing a direct comparison of the three cell chemistries, the influence of the trigger method on the vent gas composition and the thermal behavior. Of the three cell chemistries, LFP releases the least amount of vent gas at 0.02 mol/Ah (41% H₂, 27% CO₂, 8% CO), followed by NVPF at 0.05 mol/Ah (42% CO₂, 17% electrolyte solvent, 15% H₂ and 10% CO) and NMC at 0.07 mol/Ah (36% CO, 24% CO₂, 19% H₂). The maximum vent gas temperature increases from NVPF (265 °C) to LFP (446 °C) and NMC (1050 °C). As for the triggers, overcharge has the highest vent gas production of the NVPF cells at 0.07 mol/Ah. The results offer valuable insight into storage system design and expand the assessment of battery cells. Full article

During a thermal runaway, Lithium-ion battery cells are subjected to a large increase in temperature, which will vaporize and potentially thermally degrade their liquid electrolyte. The formation of gas in the battery cell will increase the pressure until the flammable gases vent and potentially lead to a fire incident. While the pyrolysis chemistry of the electrolyte components has been studied near atmospheric pressure, the effect of pressure has not been investigated. This study was undertaken to better understand the effect of pressure on the thermal dissociation of two common linear electrolyte components, diethyl carbonate (DEC) and ethyl methyl carbonate (EMC). The pyrolysis of DEC and EMC was studied in the gas phase, in 99.75% He/Ar, and was carried out at high temperatures and for pressures near 5.5 atm. The time-resolved CO formation was measured using a quantum cascade laser, providing a unique experimental dataset. A detailed chemical kinetics analysis was performed to understand the effect of pressure on DEC and EMC, with CO time-history results obtained in similar conditions at near-atmospheric pressure for DEC and EMC serving as baselines for comparison. Numerical predictions using detailed chemical kinetics mechanisms from the literature were carried out, and reaction pathways at different pressures were highlighted to emphasize the effect of pressure on the pyrolysis chemistry. Full article

Thermal runaway (TR) has become a critical safety concern with the widespread use of lithium-ion batteries (LIBs) as an energy storage solution to meet the growing global energy demand. This issue has become a significant barrier to the expansion of LIB technologies. Addressing the urgent need for safer LIBs, this study developed a comprehensive model to simulate TR in cylindrical 18650 nickel cobalt manganese (NMC) LIBs. By incorporating experiments with LG^®-INR18650-MJ1 cells, the model specifically aimed to accurately predict critical TR parameters, including temperature evolution, internal pressure changes, venting phases, and mass loss dynamics. The simulation closely correlated with experimental outcomes, particularly in replicating double venting mechanisms, gas generation, and the characteristics of mass loss observed during TR events. This study confirmed the feasibility of assuming proportional relationships between gas generation and the cell capacity and between the mass loss from solid particle ejection and the total mass loss, thereby simplifying the modeling of both gas generation and mass loss behaviors in LIBs under TR. Conclusively, the findings advanced the understanding of TR mechanisms in LIBs, providing a solid foundation for future research aimed at mitigating risks and promoting the safe integration of LIBs into sustainable energy solutions. Full article

Lithium-ion batteries have been increasingly demonstrated in reuse applications for environmental and economic reasons, and stationary energy storage systems (ESS) and mobile ESS are emerging as reuse applications for electric vehicle batteries. Most mobile ESS deployments are at large scales, necessitating experimental data on thermal runaway (TR) to ensure comprehensive safety. In this study, TR induction and suppression experiments were conducted using fully charged NCM-based batteries at the cell (750 Wh), module (7.5 kWh), and pack (74 kWh) levels. The stepwise TR experiments measured changes in temperature, voltage, heat release rate, volatile organic compound concentrations, and vent gas composition. The suppression experiments assessed the effective water injection rate, timing, and volume required to mitigate TR propagation. The results demonstrate that in the case of TR caused by thermal abuse, early detection of battery abnormalities is possible through monitoring pre-TR indicators, such as temperature and vent gas concentration. It was also confirmed that CO₂ injections can effectively cool the battery without causing damage. Furthermore, it is proposed that rapid water injection, directly contacting the battery immediately after the onset of TR, can successfully prevent TR propagation. Full article

We propose a hypothesis for the simultaneous emergence of bacteria, archaea, viruses, and mobile elements by sequential and concrete biochemical pathways. The emergence process can be considered analogous to crystallization, where genetic and biochemical systems stabilize as organisms evolve from their common ancestor, the LUCA, which was a non-free-living pool of single operon type genomes including double-stranded (ds) DNA at an ancient submarine alkaline vent. Each dsDNA operon was transcribed by different systems in σ, TFIIB, or TBP genomes. Double-stranded DNA operons can fuse and stabilize through the action of specific transcription systems, leading to differentiation between the Bacteria (σ genome) and Archaea (TBP genome) domains. Error catastrophe can be overcome by the parallel gain of DNA replication and DNA repair mechanisms in both genomes. Enlarged DNA enabled efficient local biochemical reactions. Both genomes independently recruited lipids to facilitate reactions by forming coacervates at the chamber of the vent. Bilayer lipid membrane formation, proto-cell formation with a permeable membrane, proto-cell division, and the evolution of membrane-associated biochemistry are presented in detail. Simultaneous crystallization of systems in non-free-living bacteria and non-free-living archaea triggered the co-crystallization of primitive viruses and mobile elements. An arms race between non-free-living cells and primitive viruses finally led to free-living cells with a cell wall and mature viruses. Full article

Sulfation plays a critical role in the biosynthesis of small molecules, regulatory mechanisms such as hormone signaling, and detoxification processes (phase II enzymes). The sulfation reaction is catalyzed by a broad family of enzymes known as sulfotransferases (SULTs), which have been extensively studied in animals due to their medical importance, but also in plant key processes. Despite the identification of some sulfated metabolites in fungi, the mechanisms underlying fungal sulfation remain largely unknown. To address this knowledge gap, we conducted a comprehensive search of available genomes, resulting in the identification of 174 putative SULT genes in the Ascomycota phylum. Phylogenetic analysis and structural modeling revealed that these SULTs belong to the aryl sulfotransferase family, and they are divided into two potential distinct clusters of PAPS-dependent SULTs within the fungal kingdom. SULT genes from two marine fungi isolated from deep-sea hydrothermal vents, Hortaea werneckii UBOCC-A-208029 (HwSULT) and Aspergillus sydowii UBOCC-A-108050 SULT (AsSULT), were selected as representatives of each cluster. Recombinant proteins were expressed in Escherichia coli and biochemically characterized. HwSULT demonstrated high and versatile activity, while AsSULT appeared more substrate-specific. Here, HwSULT was used to sulfate the mycotoxin zearalenone, enhancing its cytotoxicity toward healthy feline intestinal cells. Full article

Gas emissions from lithium-ion batteries (LIBs) have been analysed in a large number of experimental studies over the last decade, including investigations of their dependence on the state of charge, cathode chemistry, cell capacity, and many more factors. Unfortunately, the reported data are inconsistent between studies, which can be explained by weaknesses in experimental methodologies, the misinterpretation of data, or simply due to the comparison of datasets that build on different prerequisites. In the present work, the literature on gassing from battery components and battery cells is reported, with a focus on vent gas composition resulting from internal chemical processing in the battery and excluding studies where the gases are combusted after venting. The aim is to identify datasets of high quality that contribute to the advancement of our understanding of gas emissions from LIBs. Gas compositions from different stages in the gassing process are included, starting with the slow formation of gases during normal operation via mild thermal events to a thermal runaway (TR) with extensive gas production. Available published data are used to map gas quantity and composition from LIBs undergoing venting, with or without a TR, and to identify gaps in understanding and the need for further research. Full article

Thermal propagation events are characterized by fire and thick black smoke, leading to propagation methods with a focus on preventing heat transfer and optimizing gas flow. Yet little attention is being paid to the electric conductivity of the gas, leading to possibly unexpected battery casing openings due to lightning arcs as well as potentially providing the minimum ignition energy. This gas composition (omitting particles) was used at different temperatures and pressures in a lightning arc test bench, leading to the Paschen curve. Using a mini-module cell setup, filtered venting gas was flowed through another lightning arc test bench, allowing for in situ measurements. Full article

The bullfrog Aquarana catesbeiana is one of the main farmed frog species in China, with a low overall survival of farmed bullfrogs from hatching to harvest since bullfrog tadpoles are fragile during the metamorphosis period. The intestinal bacterial community can play crucial roles in animal development; however, little is known about the alteration of the gut microbial community of A. catesbeiana during metamorphosis. The present study used 16S rRNA amplicon sequencing to investigate the intestinal bacterial community in A. catesbeiana at four distinct developmental stages. Moreover, we determined the bullfrog’s body morphological parameters and the intestine histology at different developmental stages. The results showed a reduction in the total length and snout–vent length of A. catesbeiana during metamorphosis. The intestinal microbial composition of A. catesbeiana exhibited variation throughout the process of metamorphosis. The terrestrial stage showed shifts in the bacterial composition compared to the aquatic stages, including a reduction in Bacteroidetes and an increase in Firmicutes. Furthermore, the presence of Prevotella, Bifidobacterium, Leucobacter, Corynebacterium, Bulleidia, Dorea, Robinsoniella, and Clostridium in A. catesbeiana metamorphosis appears to be mainly related to the host’s epithelial cells’ height and total body mass. The results indicated that the intestinal microbial composition changed with the bullfrog–tadpole metamorphosis. The genera of Prevotella, Bifidobacterium, Leucobacter, Corynebacterium, Bulleidia, Dorea, Robinsoniella, and Clostridium might be potential probiotics. Full article

Lithium-ion batteries (LIBs) are employed in a range of devices due to their high energy and power density. However, the increased power density of LIBs raises concerns regarding their safety when subjected to external abuse. The thermal behavior is influenced by a number of factors, i.e., the state of charge (SoC), the cell chemistry and the abuse conditions. In this study, three distinct cylindrical Li-ion cells, i.e., lithium nickel cobalt aluminum oxide (NCA), lithium titanate oxide (LTO), and lithium iron phosphate (LFP), were subjected to thermal abuse (heating rate of 5 °C/min) in an air flow reactor, with 100% SoC. Venting and thermal runaway (TR) were recorded in terms of temperature and pressure, while the emitted products (gas, solid, and liquid) were subjected to analysis by FT-IR and ICP-OES. The concentrations of the toxic gases (HF, CO) are significantly in excess of the Immediate Danger to Life or Health Limit (IDLH). Furthermore, it is observed that the solid particles are the result of electrode degradation (metallic nature), whereas the liquid aerosol is derived from the electrolyte solvent. It is therefore evident that in the event of a LIB fire, in order to enhance the safety of the emergency responders, it is necessary to use appropriate personal protective equipment (PPE) in order to minimize exposure to toxic substances, i.e., particles and aerosol. Full article

Lithium-ion batteries (LIB) pose a safety risk due to their high specific energy density and toxic ingredients. Fire caused by LIB thermal runaway (TR) can be catastrophic within enclosed spaces where emission ventilation or occupant evacuation is challenging or impossible. The fine smoke particles (PM_2.5) produced during a fire can deposit in deep parts of the lung and trigger various adverse health effects. This study characterizes the chemical composition of PM_2.5 released from TR-driven combustion of cylindrical lithium iron phosphate (LFP) and pouch-style lithium cobalt oxide (LCO) LIB cells. Emissions from cell venting and flaming combustion were measured in real time and captured by filter assemblies for subsequent analyses of organic and elemental carbon (OC and EC), elements, and water-soluble ions. The most abundant PM_2.5 constituents were OC, EC, phosphate (PO₄³⁻), and fluoride (F⁻), contributing 7–91%, 0.2–40%, 1–44%, and 0.7–3% to the PM_2.5 mass, respectively. While OC was more abundant during cell venting, EC and PO₄³⁻ were more abundant when flaming combustion occurred. These freshly emitted particles were acidic. Overall, particles from LFP tests had higher OM but lower EC compared to LCO tests, consistent with the higher thermal stability of LFP cells. Full article

Prodigiosin is a red bacterial pigment with great potential as a natural dye and drug precursor, while presenting several pharmacological properties, including antimicrobial and anticancer activities. Its commercialization for biomedical applications, however, remains scarce. The major limitations are related to the lack of efficient bioprocesses and scaling up from laboratory to production. In the present work, the upstream process for prodigiosin production was developed using a marine Serratia rubidaea isolated from a sample collected near a shallow-water hydrothermal vent. The yield of product per biomass was found to be influenced by the cell concentration in the inoculum. The system was scaled up to 2 L stirred tank reactors with two different vessel geometries. It was shown that the vessel geometry and a cascade control mode for regulating the dissolved oxygen concentration influenced the volumetric oxygen mass transfer coefficient (k_La) and thus prodigiosin production. To improve product yields, strategies to mimic the aeration conditions found at the sampling site were tested. When the inoculum was grown for 5 h at 200 rpm and for 19 h at 25 rpm, which significantly decreased the oxygen available, the cells produced 588.2 mg_product/g_biomass, corresponding to a production of 1066.2 mg of prodigiosin in 24 h and a productivity of 36.1 mg_product/(L.h). This is a 3.7-fold increase in prodigiosin yield and a 4.5-fold increase in productivity in relation to when no particular strategy was promoted. Additionally, it was shown that lipid analysis and flow cytometry may be used as reliable at-line analytical tools, allowing the monitoring of cell condition and prodigiosin production during fermentation. Full article