Search Results (95)

Microwave (MW) technology has attracted considerable attention as a promising approach for environmentally benign chemical processes owing to its high energy efficiency and potential for process simplification. Similarly, enzymatic reactions, which are characterized by high substrate specificity and mild reaction conditions, are indispensable technologies in both academic research and industrial applications and are widely recognized as representative green chemistry processes owing to their feasibility in aqueous media and the suppression of byproduct formation. The integration of enzymatic reactions with MW technology, referred to as MW-assisted enzymatic reactions, is therefore regarded as a promising research area. Enzymes, which are predominantly proteins and are structurally more complex than peptides, function as key catalytic entities in diverse biochemical reactions. Investigating the interactions between MWs and proteins and understanding how these interactions induce structural changes in protein molecules areessential for elucidating the effects of MW irradiation on enzymatic reactions. This review focuses on the effects of MW irradiation on protein conformations and enzymatic reactions. The insights presented herein are expected to contribute to a deeper understanding of MW-assisted enzymatic processes and the rational design of future sustainable reaction systems. Full article

Seafood processing generates large volumes of by-products that are often underutilized despite their potential as sources of high-value bioactive lipids. In this study, a hybrid process integrating microwave (MW) pretreatment with Soxhlet (SOX) extraction was developed and optimized to intensify the recovery of astaxanthin (ASX)- and ω-3 PUFA-rich oil from green tiger shrimp (Penaeus semisulcatus) residues. Response surface methodology (RSM) comprising 22 experimental runs was applied to optimize key MW process variables, including power (100–400 W) and irradiation time (30–90 s). Both factors significantly influenced oil yield, with optimal operating conditions identified at 400 W and 75 s. MW pretreatment promoted structural disruption of shrimp shells, as confirmed by scanning electron microscopy, thereby enhancing solvent penetration and mass transfer. Solvent selection further affected extraction performance: hexane:isopropanol (1:1, v/v) achieved the highest oil yield (3.86 g/100 g dry weight), while hexane:acetone produced extracts with the highest ASX concentration (1032.24 µg/g oil), ω-3 PUFA content (29.85%), and antioxidant activity (93.30% DPPH scavenging). Colorimetric analysis supported these results, with increased redness (a* = 18.12) correlating with ASX enrichment. Overall, this integrated MW-SOX process represents an effective process-intensification strategy for sustainable shrimp waste valorization and production of bioactive lipid fractions. Full article

Cell-penetrating peptides (CPPs) have been extensively explored as tools for the intracellular delivery of diverse molecular cargoes. Although substantial progress has been made in elucidating their uptake mechanisms and sequence-dependent functions, limitations in cellular internalization efficiency remain a major challenge, hindering their broader biomedical application. To address this issue, the present study investigated whether microwave (MW) irradiation at 2.45 GHz can enhance CPP-mediated delivery. Using confocal laser scanning microscopy and fluorescence spectroscopy, we examined the effects of MW irradiation on the cellular uptake of arginine-rich peptides. Our results suggested that MW irradiation enhanced the cellular uptake of the peptides. These findings imply that CPP-mediated delivery assisted by MW irradiation is an effective method for improving intracellular transport and may open new avenues for the development of advanced drug delivery systems. Full article

Background/Objectives: Enhancing excipient functionality through environmentally friendly and scalable processing methods is essential for improving the manufacturability and performance of orally disintegrating tablets (ODTs). Microwave-assisted wet granulation enables controlled microstructural modification without chemical alteration of excipient components. This study aimed to develop and evaluate a rice starch (RS)–mannitol co-processed excipient using microwave-assisted wet granulation for direct compression of ODTs. Methods: RS and mannitol were co-processed by wet granulation followed by microwave treatment under varying power levels and irradiation times. The effects of processing conditions on granule morphology, solid-state properties, porosity, powder flow, compressibility, wettability, and disintegration behavior were systematically investigated. The optimized excipient was further evaluated in ODT formulations containing chlorpheniramine maleate and piroxicam and benchmarked against a commercial co-processed excipient (Starlac^®). Results: Microwave treatment generated internal vapor pressure that promoted pore formation and particle agglomeration, resulting in enhanced powder flowability (compressibility index 8.4–10.8%). Partial crystallinity reduction and microstructural modification improved compressibility and surface wettability compared with non-microwave-treated materials. The optimized formulation (MW-RM-H-30) exhibited rapid wetting (25 s), high water absorption (90.5%), low contact angle (42°), and fast tablet disintegration (31 s). ODTs prepared with MW-RM-H-30 showed rapid disintegration (42 s for chlorpheniramine maleate and 32 s for piroxicam) and dissolution behavior comparable to Starlac^®. Conclusions: Microwave-assisted wet granulation provides an efficient, scalable, and environmentally friendly strategy for engineering starch-based co-processed excipients with enhanced functionality for direct compression ODT applications. The developed excipient demonstrates strong potential for solid dosage form manufacturing. Full article

This study investigated the effects of microwave (MW) pre-treatment (45 kJ total irradiated microwave energy) and magnetic nanoparticles (MPs) on the anaerobic digestion (AD) of meat-processing sludge, integrating biokinetic modeling with dielectric parameter measurements. Five different sludge variants were examined: native (non-treated control); MP-only control; microwave pre-treated sludge, and MW + MP combination with the nanoparticles either retained in the fermentation medium or removed prior to anaerobic digestion. Cumulative biomethane production was evaluated using the modified Gompertz, Logistic, and Weibull models, and key kinetic parameters (maximum achievable methane yield, maximum rate of product formation, and λ-values) were compared across the different treatments. The results revealed that the highest production rate, along with the highest biomethane potential, could be achieved when combining MW treatment with magnetic nanoparticles which were retained in the fermentation medium during AD. Based on the biokinetic analysis, this combined method increased biomethane potential by 52% to 390 mL CH₄/gVS and maximum methane production rate by 85% to 37 mL CH₄/gVS/day compared to the untreated control. The measurement of relative permittivity (${\epsilon }^{\prime }$) exhibited progressive changes during digestion, and the maximum rate of change in ${\epsilon }^{\prime }$ strongly correlated with the maximum methane production rate across all samples (R² > 0.98). These results highlight the potential of microwave–metal oxide nanoparticle pre-treatment for process enhancement and to demonstrate the suitability of dielectric parameter measurement as a rapid, non-invasive indicator of biochemical activity during anaerobic digestion. Full article

4,4′-substituted-2,2′-((hexahydro-1H-benzo[d]imidazole-1,3(2H)-diyl)bis(methylene))bisphenols (1a–d) and 2,6-bis{[3-(2-hydroxy-5-substitutedbenzyl)octahydro-1H-benzimidazol-1-yl]methyl}-4-substitutedphenols (2a–b) were synthesized via microwave (MW) irradiation of aminal (2R,7R,11S,16S)-1,8,10,17-tetraazapentacyclo[8.8.1.1.^8,170.^2,70.^11,16]icosane 2 with p-substituted phenols. Microwave (MW) irradiation improved reaction rates and yields at 80 °C. Compounds 1a–d were racemic, and 2a–b were diastereomeric. NMR spectra revealed key signals for the perhydrobenzimidazole fragment, aromatic rings, and aminal carbons. Differences in the ¹³C NMR spectra highlighted structural variations, such as distinct carbonyl and methoxyl signals in 2d. MW irradiation at higher temperatures (100–120 °C) reduced yields of 1, especially for phenols with methyl (Me) and methoxy (OMe) groups, suggesting a shift toward the formation of compound 2. Additionally, higher temperatures led to polymerization byproducts, emphasizing the impact of MW energy on reaction pathways. These results provide valuable insights for designing molecules with potential applications in materials science and medicinal chemistry. Full article

This study presents the synthesis and antidiabetic and hematopoietic activity of ionic compounds based on 2-(diphenylmethoxy)-N,N-dimethylethanamine (diphenhydramine). Synthesis is carried out under ultrasonic (US) and microwave (MW) irradiation as well as using a conventional method (thermal activation). The synthesized ionic compounds have been tested for antidiabetic effect according to the inhibitory action against α-glucosidase and α-amylase (in vitro). All the synthesized derivatives of diphenhydramine showed higher inhibitory activity against α-glucosidase than commercially available diphenhydramine hydrochloride. Moreover, two of them, 1m (66.9%) and 1k (64.2%), had a greater inhibitory activity than the reference drug acarbose (51.8%). The hematopoietic activity was studied in albino laboratory female rats (in vivo). The compounds 1b, 1f, and 1k can restore immune blood cells (hematopoietic activity), equal to or exceeding that of the commercially available diphenhydramine hydrochloride and control (methyluracil). Full article

Chicken feathers constitute a major by-product from the poultry industry, with a potential environmental impact and significant difficulties in their management. This study aimed to develop a sustainable method to hydrolyse chicken feathers and evaluate the effects of microwave (MW) irradiation pre-treatment in the generation of bioactive hydrolysates by simple or sequential hydrolysis with Alcalase. The hydrolysate with MW irradiation pre-treatment and Alcalase (2%, 2 h) (MWA) showed the highest overall antioxidant activity and neprilysin-inhibitory activity (55%), whereas samples without MW irradiation pre-treatment exerted the highest inhibitory activity of dipeptidyl peptidase IV (DPP IV) and angiotensin-converting enzyme (ACE-I), with values close to 50 and 70%, respectively. Mass spectrometry in tandem of bioactive hydrolysates was performed, and an in silico approach was used to characterise the obtained sequences. These results confirmed that MW irradiation pre-treatment improved Alcalase hydrolysis, leading to the generation of bioactive peptides with potential multifunctional properties, including antioxidant, antidiabetic, and antihypertensive activities. Moreover, this study highlights the potential of combining MW irradiation and enzymatic hydrolysis as a sustainable strategy for the revalorisation of chicken feathers. Full article

Millimeter-wave-supported detonation (MSD) is a unique detonation phenomenon driven by a supersonically propagating ionization front, sustained by intense millimeter-wave beams. Microwave Rocket, which utilizes MSD to generate thrust from atmospheric air in a pulse detonation engine (PDE) cycle, is a promising low-cost alternative to conventional chemical propulsion systems for space transportation. However, insufficient air intake during repetitive PDE cycles has limited achievable thrust performance. To address this issue, a model equipped with a six-stage reed valve system (36 valves in total) was developed to ensure sufficient air intake, which measured 500 mm in length, 28 mm in radius, and 539 g in weight. Launch demonstration experiments were conducted using a 170 GHz, 550 kW gyrotron developed at the National Institutes for Quantum Science and Technology (QST). Continuous thrust was successfully generated by irradiating up to 50 pulses per experiment at each frequency between 75 and 150 Hz, in 25 Hz increments, corresponding duty cycles ranging from 0.09 to 0.18. A maximum thrust of 9.56 N and a momentum coupling coefficient $C_m$ of 116 N/MW were obtained. These values represent a fourfold increase compared to previous launch experiments without reed valves, thereby demonstrating the effectiveness of the reed valve configuration in enhancing thrust performance. Full article

Herein, we report on the synthesis of Ni and Zn clusters on the surface of TiO₂ as well as their bimetallic NiZn analogs. The materials were prepared by incipient wet impregnation of colloidal TiO₂ followed by microwave (MW) irradiation to graft the clusters to TiO₂ surface. The materials were further immobilized onto glass slides and exhibited high surface area, high mechanical stability, and porosity with accessible pores. The main species responsible for visible light degradation of microcystin LR via the interface charge transfer (IFCT) of excited e⁻ to surface metal clusters were found to be O₂^•− and h⁺. The optimal nominal grafting concentration was 0.5 wt.% for Ni and 1.0 wt.% for Zn, while for the bimetal modification (NiZn), the optimal nominal concentration was 0.5 wt.%. Compared to monometallic, bimetallic grafting showed a lower kinetic constant, albeit still improved compared to bare TiO₂. Bimetal-modified titania showed a lower photocurrent compared to single metal-grafted TiO₂ and poorer interfacial charge transport, namely, more recombination sites—possibly at the interface between the Ni and Zn domains. This work highlights the efficiency of using MW irradiation for grafting sub-nano-sized metallic species to TiO₂ in a homogeneous way. However, further strategies using MW irradiation for the structural design of bimetallic cocatalysts can be implemented in the future. Full article

Chert gravel, a byproduct of sand quarrying, remains an underutilized material in construction due to its low microwave (MW) absorption and high mechanical strength. The present study deals with the potential of MW irradiation as a novel, energy-efficient method for processing chert gravel into high-quality aggregates, reducing reliance on virgin materials. The research systematically examines MW exposure duration (1–2.5 min), rock size (150–800 g), moisture conditions, and cooling methods (air vs. water quenching) to optimize fragmentation. Experimental results indicate that larger rock sizes (600–800 g) yield coarser, less uniform aggregates, while prolonged MW exposure (>2 min) induces extensive micro-fracturing, producing finer, well-graded particles. Water quenching significantly intensifies fragmentation, generating irregular but highly fragmented aggregates, whereas pre-wetted samples exhibit finer and more uniform breakage than dry samples. The findings introduce a novel approach for optimizing chert gravel fragmentation, a material previously considered unsuitable for MW treatment. The study proposed a customizable methodology for tailoring aggregate properties through precise control of MW parameters, offering a sustainable alternative to conventional crushing. The results contribute to resource conservation, reduced energy consumption, and climate change mitigation, paving the way for more sustainable construction practices. Full article

The rapid detoxification and mineralization of Cr(VI) in aqueous environments hold critical importance for emergency response and resource recovery yet remain technically challenging. Herein, we report the synthesis of FeS₂/ZVI composites through ethanol-assisted wet ball-milling and their application in Cr(VI) removal under microwave (MW) irradiation. This study systematically investigates the effects of MW irradiation on the removal efficiency of Cr(VI) using FeS₂/ZVI composites, with particular focus on key parameters including composite dosage, initial pH, MW temperature, and Cr(VI) concentration. Notably, 1 g/L FeS₂/ZVI composites achieved near-complete removal (>99%) of 50 mg/L Cr(VI) within 7 min at a MW irradiation temperature of 333 K, which exhibited 5.9-fold and 13.1-fold superior performance compared to pure pyrite and ZVI, respectively. Additionally, there is a 96.1% reduction in reaction time in comparison to non-MW irradiation system. In real electroplating wastewater samples, Cr(VI) concentration was reduced from 38.93 to 0.42 mg L⁻¹ by MW irradiation-assisted treatment, validating its potential for practical applications in industrial Cr(VI) pollution control. The activation energy determined by fitting the Arrhenius equation showed a 39.7% reduction for the MW-assisted FeS₂/ZVI system (16.0 kJ mol⁻¹) compared to conventional thermal heating (from 25.6 kJ mol⁻¹), indicating that MW irradiation induced catalytic enhancement of FeS₂/ZVI, thereby lowering the energy barrier for Cr(VI) reduction. Moreover, MW irradiation-assisted processes facilitated the mineralization of reduced Cr(III) to stable spinel FeCr₂O₄. These findings collectively establish a synergistic mechanism between MW activation and FeS₂/ZVI composites, offering innovative pathways for efficient Cr(VI) detoxification and resource recovery from high-strength industrial wastewaters. Full article

Green chemistry seeks to find alternative synthesis routes that are less harsh to living organisms and the environment. In this communication, a microwave-assisted hydrothermal technique and a thermal annealing method were used in the reduction of graphene oxide (GO) to make reduced GO (rGO). Graphite powder was oxidised using the Improved Hummers’ method, exfoliated, and freeze-dried. Thereafter, an aqueous suspension of GO was reduced under microwave (MW) irradiation for 10 min at 600 W with and without the help of a reducing agent (hydrazine hydrate). Thermal annealing reduction was also conducted under a nitrogen atmosphere at 300 °C for 1 h. Prepared samples were analysed using Raman laser spectroscopy, X-ray diffraction (XRD), transmission electron microscopy (TEM), the Brunauer–Emmett–Teller (BET) method, and X-ray photoelectron spectroscopy (XPS). A successful reduction in the GO functional groups between the sheets was established using XRD. In the Raman analysis, the ratio of the intensity of the D and G band (I_D/I_G) in graphene sheets assisted in assessing the quality of the graphene films. An estimation of the number of structural defects was calculated using the I_D/I_G ratio. The Raman analysis showed an increase in the I_D/I_G ratio after both oxidation and reduction processes. The defect densities of both MW-treated samples were comparable while an increased defect density was evident in the thermally annealed sample. TEM micrographs confirmed the sheet-like morphology of the samples. The rGO sheets obtained from the MW-treated method appeared to be smaller when compared to the rGO ones obtained by thermal treatment. It was also evident from XRD analysis that thermal treatment promoted the coalition of graphitic layers, such that the estimated number of layers was larger than that of GO. The elemental analysis showed that the C/O ratio of GO increased from 2 to 7.8 after MW hydrazine reduction. Full article

In this study, a set of spiro[5,8-methanoquinazoline-2,3′-indoline]-2′,4-dione derivatives 3a–p were synthesized starting from unsubstituted and N-methyl-substituted diendo- and diexo-2-aminonorbornene carboxamides, as well as various substituted isatins. The typical method involves a condensation reaction of alicyclic aminocarboxamide and isatin in the presence of a catalyst, using a solvent and an acceptable temperature. We developed a cost-effective and ecologically benign high-speed ball milling (HSBM), microwave irradiation (MW), and continuous flow (CF) technique to synthesize spiroquinazolinone molecule 3a. The structures of the synthesized compounds 3a–p were determined using 1D and 2D NMR spectroscopies. Furthermore, docking studies and absorption, distribution, metabolism, and toxicity (ADMET) predictions were used in this work. In agreement with the corresponding features found in the case of both the SARS-CoV-2 main protease (RCSB Protein Data Bank: 6LU7) and human mast cell tryptase (RCSB Protein Data Bank: 2ZA5) based on the estimated total energy and binding affinity, H bonds, and hydrophobicity in silico, compound 3d among our 3a–g, 3i–k, and 3m derivatives was found to be our top-rated compound. Full article

N₂ oxidation to NO_x is a challenging reaction, and alternative routes to the industrial Ostwald process are of interest. A perovskite under flowing O₂-N₂ mixtures at atmospheric pressure in a quartz tube reactor was irradiated by microwaves (MW), leading to the formation of hot spots and plasmas within the catalyst bed. NO_x concentrations up to 2.5 vol.% in one pass were obtained at 600 W. Using a lower MW power of 100 W led to a pulsed mode yielding lower NO_x concentrations and no noticeable damage to the quartz reactor. The formation of plasma was strongly dependent on the perovskite bed packing. The perovskite acted primarily as a susceptor and likely also as a catalyst, although the proportion of heterogeneous and homogenous reactions could not be determined in the present study. The simple reactor layout allowing operation at atmospheric pressure is promising for the development of practical MW-assisted N₂ fixation technologies. Full article