Search Results (101)

Considerable research in recent years has examined the reuse of tailings; however, the lack of particle cohesion limits their application as construction materials. Therefore, this study assessed the stabilization of ultrafine iron ore tailings using an acrylic–styrene copolymer. Geotechnical characterization and polymer dosage, hydromechanical and microstructural tests were carried out, including unconfined compressive strength (UCS), permeability, scanning electron microscopy (SEM) and microtomography (μCT). The polymer effectively enhanced the mechanical behavior of the tailings, increasing the UCS from 49 kPa for untreated material to 2114 kPa and 3324 kPa for 30% and 40% polymer content, respectively. A robust power-law model (R² ≥ 0.90), based on the porosity/volumetric polymer index (η/Pᵢᵥ), was developed to predict strength, showing that mechanical gains can be achieved by increasing either polymer content or dry density, as supported by statistical analyses. Permeability remained on the order of 10⁻⁶ cm/s regardless of polymer addition, indicating that the polymer does not fill voids but instead acts as a binding agent, as confirmed by SEM and μCT analyses. Overall, this study establishes a technically feasible and sustainable approach for tailings management, highlighting the potential of polymer stabilization to turn environmentally challenging tailings into functional geotechnical materials. Full article

The development of hydrophilic biodegradable polymers is crucial for a range of biomedical applications, including targeted drug delivery and prosthetics. Ring-opening polymerization of substituted ε-caprolactone monomers provides an efficient method for the synthesis of polyesters with tailored properties. In this work, a synthetic approach for the preparation of ester- and morpholinoamido-disubstituted ε-caprolactone monomers was developed. Poorly defined polymers were obtained from the monomers, bearing two ester groups due to the competitive transesterification of the pendant substituents. On the other hand, the disubstituted morpholinoamido-ε-caprolactone was polymerized in a controlled manner by ring-opening polymerization, and amorphous homopolymers with a high glass transition temperature (112 °C) and good solubility in water were obtained. Statistical and block copolymers with the unsubstituted ε-caprolactone were also prepared, and DLS analysis of the amphiphilic block copolymers in water shows the presence of self-assembled particles. These results demonstrate the potential of morpholinoamido-functionalized ε-caprolactone derivatives as building blocks for the development of biodegradable polymeric materials for biomedical applications. Full article

This study investigates the mechanical properties of double hydrophilic block copolymers (DHBCs) based on poly[oligo(ethylene glycol) methacrylate] (POEGMA) and poly(vinyl benzyl trimethylammonium chloride) (PVBTMAC) blocks by employing small amplitude oscillatory shear (SAOS) rheological measurements. We report that the mechanical properties of DHBCs are governed by the interfacial glass transition temperature (T_g^inter), verifying the disordered state of these copolymers. An increase in zero shear viscosity can be observed by increasing the VBTMAC content, yielding a transition from liquid-like to gel-like and finally to an elastic-like response for the PVBTMAC homopolymer. By changing the block arrangement along the backbone from statistical to sequential, a distinct change in the viscoelastic response is obvious, indicating the presence/absence of bulk-like regions. The tunable viscosity values and shear-thinning behavior achieved through alteration of the copolymer composition and block arrangement along the backbone render the studied DHBCs promising candidates for drug delivery applications. In the second part, the rheological data are analyzed within the framework of the classical free volume theories of glass formation. Specifically, the copolymers exhibit reduced fractional free volume and similar fragility values compared to the PVBTMAC homopolymer. On the contrary, the activation energy increases by increasing the VBTMAC content, reflecting the required higher energy for the relaxation of the glassy VBTMAC segments. Overall, this study provides information about the viscoelastic properties of DHBCs with densely grafted macromolecular architecture and shows how the mechanical and dynamical properties can be tailored for different drug delivery applications by simply altering the ratio between the two homopolymers. Full article

The growing demand for passenger comfort and environmental protection, as well as reducing fuel consumption and exhaust emissions, drives the search for new, high-performance materials. Composite leaf springs, applied as part of elastic suspension systems and with the advantages of being strong and lightweight, with a high load-carrying capacity, are a possible method with which to achieve those goals. In this study, an epoxy thermoset was blended with 10–50 wt.% polysulfide rubber and reinforced with 10 wt.% alumina powder. The characteristics of the copolymer composite blend were studied by performing ASTM mechanical tests, including tensile strength, impact strength, hardness, and damping ratio tests. The experimental outcomes showed that increasing the proportion of polysulfide rubber caused a reduction in the maximum tensile strength, modulus at fracture, natural as well as damped frequency, and hardness, whereas a significant improvement was observed in impact strength, logarithmic decrement, and the damping ratio. Reinforcement with alumina powder caused a meaningful increase in the maximum tensile strength and natural frequency, with a good improvement in deformation strength. Impact strength and the damping ratio were maximized when alumina powder was increasingly added. This increase was contrary to what occurred for the hardness, which decreased upon reinforcement. Statistical methods, altering the design of the experiments, and linear regression were used to optimize the composite mixture for manufacturing leaf springs. Finally, the model was validated using analysis of variance and probability plots (normal distribution). The regression equations of tensile and impact strength, hardness, and damping ratio test results proved composite suitability for the application of leaf springs under representative loading and operating conditions. Finite element analysis of the composite material was performed using SolidWorks Simulation 22 Mechanical software. ANSYS 2022 R1 was used to study the mechanical properties of the leaf spring model fabricated from the proposed composite material. The finite element analysis results showed a significant reduction in the weight of leaf springs, with very good mechanical properties, including the tensile and impact strength, hardness, and damping ratio, when using the proposed copolymer-reinforced composite material. Full article

Amphiphilic statistical copolymers can be utilized for the formulation of nanocarriers for the drug delivery of insoluble substances. Oligoethylene glycol methylether methacrylate and methyl methacrylate are two biocompatible monomers that can be used for biological applications. In this work, the synthesis of linear poly(oligoethylene glycol methylether methacrylate-co-methyl methacrylate), P(OEGMA-co-MMA), and statistical copolymers via reversible addition fragmentation chain transfer (RAFT) polymerization is reported. P(OEGMA-co-MMA) copolymers with different comonomer compositions were synthesized and characterized by size exclusion chromatography (SEC), ¹H-NMR, and ATR-FTIR spectroscopy. Self-assembly studies were carried out by the dissolution of polymers in water and via the co-solvent protocol. For the characterization of the formed nanoaggregates, DLS, zeta potential, and fluorescence spectroscopy (FS) experiments were performed. Such measurements delineate the association of copolymers into aggregates with structural characteristics dependent on copolymer composition. In order to investigate the drug encapsulation properties of the formed nanoparticles, curcumin and quercetin were loaded into them. The co-solvent protocol was followed for the encapsulation of varying concentrations of the two drugs. Nanocarrier formulation properties were confirmed by DLS while UV–Vis and FS experiments revealed the encapsulation loading and the optical properties of the drug-loaded nanosystems in each case. The maximum encapsulation efficiency was found to be 54% for curcumin and 49% for quercetin. For all nanocarriers, preliminary qualitive biocompatibility studies were conducted by the addition of FBS medium in the copolymer aqueous solutions which resulted in no significant interactions between copolymer aggregates and serum proteins. Novel nanocarriers of curcumin and quercetin were fabricated as a first step for the utilization of these statistical copolymer nanosystems in nanomedicine. Full article

The paper describes changes in the structure, morphology, mechanical and thermal properties of porous film samples of poly(4,4′-oxidiphenylene)pyromellitimide prepared as a result of selective destruction of urethane blocks in copolymers composed of pyromellitimide blocks and polyurethane blocks. The initial samples of the new composition of statistical copoly(urethane-imide)s (CoPUIs) were prepared via polycondensation methods using pyromellitic dianhydride (PMDA), 4,4′-oxidyaniline (ODA), 2,4-toluylenediisocyanate (TDI), as well as polycaprolactone (PCL) and poly(1,6-hexanediol/neopentylglycol-alt-adipic acid) (ALT) as monomers. The molar ratio of imide and polyurethane blocks in CoPUI was 10:1. The initial films were heated up to 170 °C to complete the polycondensation processes, after which they were subjected to thermolysis and hydrolysis. The thermolysis (thermal degradation) of copolymers was carried out by heating the initial samples to temperatures of 300 °C or 350 °C. Then, the thermolized films were subjected to chemical degradation in hydrolytic baths containing an aqueous solution of potassium hydroxide. As a result, urethane blocks were destroyed and removed from the polymer. The resulting products practically did not contain polyurethane links and, in chemical composition, were practically identical to poly(4,4′-oxidiphenylene)pyromellitimide. NMR and IR spectroscopy, atomic force microscopy, X-ray diffraction, thermogravimetric analysis, differential scanning calorimetry and dynamic mechanical analysis and mechanical properties testing were used to determine the differences in the structure and properties of the initial copolymers and targeted products. The effect of the conditions of destructive processes on the structure, morphology and mechanical properties of the obtained porous polyimide films was determined. From a practical point of view, the final porous films are promising as membranes for filtering aggressive amide solvents at high temperatures. Full article

In this study, we report the synthesis of amphiphilic hyperbranched poly[(2-dimethylaminoethyl methacrylate)-co-(benzyl methacrylate)] statistical copolymers with two different stoichiometric compositions using the reversible addition–fragmentation chain transfer polymerization (RAFT) technique. The selection of monomers was made to incorporate a pH and thermoresponsive polyelectrolyte (DMAEMA) component and a hydrophobic component (BzMA) to achieve amphiphilicity and study the effects of architecture and environmental factors on the behavior of the novel branched copolymers. Molecular characterization was performed through size exclusion chromatography (SEC) and spectroscopic characterization techniques (¹H-NMR and FT-IR). The self-assembly behavior of the hyperbranched copolymers in aqueous media, in response to variations in pH, temperature, and ionic strength, was studied using dynamic light scattering (DLS), electrophoretic light scattering (ELS), and fluorescence spectroscopy (FS). Finally, the efficacy of the two novel copolymers to encapsulate curcumin (CUR), a hydrophobic, polyphenolic drug with proven anti-inflammatory and fluorescence properties, was established. Its encapsulation was evaluated through DLS, UV–Vis, and fluorescence measurements, investigating the change of hydrodynamic radius of the produced mixed copolymer–CUR nanoparticles in each case and their fluorescence emission properties. Full article

Tuning the critical solution temperature (CST) of thermoresponsive polymers is essential to exploit their immense potential in various applications. In the present study, the effect of PEG-methyl ether methacrylate with a higher molecular weight of 1100 g/mol (mPEGMA₁₁₀₀) as a comonomer was investigated for its suitability for the CST adjustment of LCST-type polymers. Accordingly, a library of mPEGMA₁₁₀₀-based copolymers was established with varying compositions (X_mPEGMA1100) using four main comonomers, namely di(ethylene glycol) ethyl ether acrylate, N-isopropyl acrylamide and methacrylamide, and mPEGMA₃₀₀, with different CST values (cloud points, T_CP, and clearing points, T_CL, by turbidimetry). It was found that less than 20 mol% of the mPEGMA₁₁₀₀ in the copolymers is practically sufficient for tuning the CST in the entire measurable temperature range, i.e., up to 100 °C, regardless of the CST of the homopolymer of the main comonomer (CST₀). Moreover, a predictive asymptotic model was developed based on the measured CST values, which strikingly revealed that the CSTs of mPEGMA₁₁₀₀-containing copolymers depend only on the two main parameters of these copolymers, X_mPEGMA1100 and the CST of the homopolymer of the main comonomer (CST₀), that is, CST = f(CST₀, X_mPEGMA1100). The revealed two-parameter relationship defines a surface in 3D plotting, and it is applicable to determine the CST of copolymers in advance for a given composition or to define the suitable composition for a required CST value. These unprecedented results on the dependence of CSTs on two major well-defined parameters enable to design a variety of novel macromolecular structures with tailored thermoresponsive properties. Full article

The microfluidic industry faces a significant challenge due to the lack of sensitive and standardized methods. One critical need is the measurement of internal channel dimensions in fully assembled chips. This study presents and compares several protocols for measuring these dimensions, including optical profilometry, optical microscopy, and tiled digital imagery. Standardized chips made from two materials commonly used in microfluidics (borosilicate glass and Cyclic Olefin Copolymer) were evaluated using each protocol. A consistency analysis using normalized error statistics identified optical profilometry as the most reliable method, offering the lowest uncertainty and the highest consistency with nominal geometry values. However, all protocols encountered difficulties with vertical depth measurements of internal structures. Future research should focus on addressing these limitations, including investigating the influence of multiple refractive surfaces on optical profilometry and exploring confocal microscopy. In conclusion, this work provides a comprehensive comparison of measurement protocols for internal microfluidic structures and offers a practical solution for applications in the microfluidic industry, while also identifying important directions for future research. Full article

Well-defined amorphous/semi-crystalline statistical copolymers of n-dodecyl isocyanate, DDIC, and allyl isocyanate, ALIC, were synthesized via coordination polymerization using the chiral half-titanocene complex CpTiCl₂(O-(S)-2-Bu) as an initiator. In the frame of the terminal model, the monomer reactivity ratios of the statistical copolymers were calculated using both well-known linear graphical methods and the computer program COPOINT. The molecular and structural characteristics of the copolymers were also calculated. The thermal properties of these samples were studied by differential scanning calorimetry, DSC, measurements. The kinetics of the thermal decomposition of the statistical copolymers was studied by thermogravimetric analysis, TGA, and differential thermogravimetry, DTG, and the activation energy of this process was calculated by employing several theoretical models. Moreover, block copolymers with the structure P[DDIC-b-(DDIC-co-ALIC)] were synthesized by sequential addition of monomers and coordination polymerization methodologies. The samples were characterized by nuclear magnetic resonance, NMR, spectroscopy; size exclusion chromatography, SEC; and DSC. The thermal stability of the blocks was also studied by TGA and DTG and compared to the corresponding statistical copolymers, showing that the macromolecular architecture greatly affects the properties of the copolymers. A thiol-ene click post-polymerization reaction was performed to introduce aromatic groups along the polyisocyanate chain in order to improve the thermal stability of the parent polymers. Evidently, these statistical and block copolymers can be employed as precursors for the synthesis of novel polyisocyanate-based materials. Full article

To prepare novel biodegradable copolymers with functional substituents that are distributed statistically or randomly over the macromolecule chain and have improved characteristics compared to homopolymers, we conducted a series of synthetic experiments with a novel cyclic monomer, 5-(benzyloxy)-1,3-dioxepan-2-one (4). This compound was synthesized, and its homopolymer, as well as its copolymers with L-lactide, ε-caprolactone and trimethylene carbonate, were prepared in a polymerization solution with stannous octoate as the initiator. The formation of the copolymers was confirmed using NMR spectroscopy and DSC data. The distribution of the monomeric units of the substituted 7CC in the copolymers with L-lactide and ε-caprolactone is random, as it is close to a statistical distribution. The copolymer with TMC is a gradient copolymer due to the different rates of monomer polymerization. The copolymer with a composition of 10(ε-CL):1(carbonate 4) can be considered a promising polymer after the deprotection of the hydroxy group for the inoculation of the functional substituents due to its convenience of preparation and properties similar to those of poly(ε-caprolactone). Full article

This study aimed to evaluate the fracture resistance of root and sealer penetration after obturation using an epoxy resin sealer AH plus (AH+) and two different bioactive endodontic sealers, i.e., Totalfill BC Hiflow (TF BC), and experimental injectable bioactive glass (Exp.BG). A thermo-sensitive injectable sealer was prepared by using a non-ionic triblock copolymer and bioactive glass. The root canals of human extracted teeth were obturated with the respective sealers. The fracture resistance was analyzed at different time intervals, i.e., days 7, 30, and 90. The morphological and elemental analyses of the fractured roots were conducted with a scanning electron microscopy and a electron dispersive spectroscopy. Sealer penetration depth and the percentage of penetrated sealers into the dentinal tubules were assessed with the confocal laser scanning microscope. Statistical analysis was performed using a one-way ANOVA post hoc Tukey’s test. The mean fracture force in AH+ was significantly higher on day 30 (664.08 ± 138.8 N) compared to day 7 (476.07 ± 173.2 N) and day 90 (493.38 ± 120.18 N). There was no statistically significant difference between the TF BC and Exp.BG at different time intervals. The maximum penetration was observed in the middle region compared to coronal and apical for the Exp.BG, followed by the TF BC and AH+ groups; however, a nonsignificant difference in penetration was found over time. It is concluded that the TF BC group showed overall better fracture resistance than AH+ at day 90. Exp.BG showed comparable sealer penetration to those of TF BC and better than those of AH+. Full article

Triterpenoid saponins from the Astragalus species possess valuable effects (cytotoxic, adjuvant, hepatoprotective, neuroprotective, antiviral, etc.). Some also have immunomodulatory activities. Astragalus glycyphyllos is distributed in Bulgaria and mainly accumulates cycloartane saponins. From the overground parts of the species, a triterpenoid cyloartane-type saponin (AGOS3) was isolated by different chromatographic techniques. A quantitative LC-MS method for the determination of the saponin was developed and validated. Further, the saponin was loaded in copolymeric micelles based on triblock copolymers of polyethylene oxide and polypropylene oxide (Pluronics). The LC-MS method was applied on the developed micelles to determine their loading degrees. Afterwards, the possible pharmacological effects of free and encapsulated in polymeric nanoparticles of triterpenoid saponin (1, 5, 10, 25, 50, and 100 µg/mL) were evaluated in isolated murine macrophages and lymphocytes in vitro. Free AGOS3 stimulated proliferation only at the highest tested concentrations (50–100 µg/mL), and the effect was more evident in isolated macrophages. Interestingly, AGOS3-loaded polymeric micelles caused concentration dependency and statistically significant increases in the proliferation of both isolated lymphocytes and macrophages, even at a lower concentration (10 µg/mL). These results could serve as the basis for further research on the immunomodulatory effect of this saponin. Full article

Despite the appealing properties of random copolymers, the use of these biomaterials in association with phospholipids is still limited, as several aspects of their performance have not been investigated. The aim of this work is the formulation of lipid/random copolymer platforms and the comprehensive study of their features by multiple advanced characterization techniques. Both biomaterials are amphiphilic, including two phospholipids (1,2-dioctadecanoyl-sn-glycero-3-phosphocholine (DSPC), 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC)) and a statistical copolymer of oligo (ethylene glycol) methyl ether methacrylate (OEGMA) and 2-(diisopropylamino) ethyl methacrylate (DIPAEMA). We examined the design parameters, including the lipid composition, the % comonomer ratio, and the lipid-to-polymer ratio that could be critical for their behavior. The structures were also probed in different conditions. To the best of the authors’ knowledge, this is the first time that P(OEGMA-co-DIPAEMA)/lipid hybrid colloidal dispersions have been investigated from a membrane mechanics, biophysical, and morphological perspective. Among other parameters, the copolymer architecture and the hydrophilic to hydrophobic balance are deemed fundamental parameters for the biomaterial co-assembly, having an impact on the membrane’s fluidity, morphology, and thermodynamics. Exploiting their unique characteristics, the most promising candidates were utilized for methotrexate (MTX) loading to explore their encapsulation capability and potential antitumor efficacy in vitro in various cell lines. Full article

The aquatic ecotoxicity of three α-amino acid-derived polyamidoamines (PAAs) was studied using zebrafish embryos as a viable vertebrate model organism. The PAAs examined were water-soluble amphoteric polyelectrolytes with a primarily negative charge, which were efficient flame retardants for cotton. The fish embryo acute toxicity test performed with PAA water solutions using 1.5–500 mg L⁻¹ concentrations showed that toxicity did not statistically differ from the control. The survival rates were indeed >90%, even at the highest concentration; the hatching rates were >80%; and the numbers of morphological defects were comparable to those of the control. Tests using transgenic zebrafish lines indicated that the numbers of microscopic vascular and musculoskeletal defects were comparable to the control, with one random concentration showing doubled alterations. Sensory–motor tests in response to visual and tactile stimuli were also performed. In the presence of PAAs, embryos exposed to alternating light/dark cycles showed an insignificant mobility reduction during the dark phase. Touch-evoked response tests revealed a mild effect of PAAs on the neuromotor system at concentrations > 10 mg L⁻¹. The cystine/glycine copolymer at 100 mg L⁻¹ exhibited the greatest effect. Overall, the studied PAAs showed a minimal impact on aquatic systems and should be further considered as promising ecofriendly materials. Full article