Next Issue
Volume 7, June
Previous Issue
Volume 7, April
 
 
polymers-logo

Journal Browser

Journal Browser

Polymers, Volume 7, Issue 5 (May 2015) – 11 articles , Pages 777-984

  • Issues are regarded as officially published after their release is announced to the table of contents alert mailing list.
  • You may sign up for e-mail alerts to receive table of contents of newly released issues.
  • PDF is the official format for papers published in both, html and pdf forms. To view the papers in pdf format, click on the "PDF Full-text" link, and use the free Adobe Reader to open them.
Order results
Result details
Section
Select all
Export citation of selected articles as:
4883 KiB  
Article
Fiber Reinforced Polymer and Polypropylene Composite Retrofitting Technique for Masonry Structures
by Saleem Muhammad Umair, Muneyoshi Numada, Muhammad Nasir Amin and Kimiro Meguro
Polymers 2015, 7(5), 963-984; https://doi.org/10.3390/polym7050963 - 22 May 2015
Cited by 38 | Viewed by 13270
Abstract
In the current research work, an attempt is made to increase the seismic capacity of unreinforced masonry (URM) structures by proposing a new composite material which can improve shear strength and deformation capacity of URM wall systems. Fiber Reinforced Polymer (FRP) having high [...] Read more.
In the current research work, an attempt is made to increase the seismic capacity of unreinforced masonry (URM) structures by proposing a new composite material which can improve shear strength and deformation capacity of URM wall systems. Fiber Reinforced Polymer (FRP) having high tensile and shear stiffness can significantly increase in-plane and out-of-plane strength of masonry walls, but, inherently, FRP strengthened wall systems exhibit brittle failure under extreme seismic loading. Polypropylene (PP-band) is a low cost material with sufficient ductility and deformation capacity. Keeping in view the behavior of FRP and PP-band, a composite of FRP and PP-band is proposed for retrofitting of URM walls. Mechanical behavior of the proposed composite material is assessed by carrying out an in-plane diagonal compression test and an out-of-plane bending test on twenty-five 1/4-scaled masonry wall panels. Experimental plan for each panel, URM, PP-band retrofitted, FRP retrofitted and FRP + PP-band retrofitted masonry, is diagonal compression test and three-point bending test. Experimental results have determined that FRP + PP-band composite increased, not only the initial peak strength, but also the ductility, deformation capacity and residual strength of URM wall systems. Full article
(This article belongs to the Collection Fiber-Reinforced Polymer Composites in Structural Engineering)
Show Figures

Graphical abstract

1896 KiB  
Article
Biopolymer Blends Based on Poly (lactic acid): Shear and Elongation Rheology/Structure/Blowing Process Relationships
by Racha Al-Itry, Khalid Lamnawar and Abderrahim Maazouz
Polymers 2015, 7(5), 939-962; https://doi.org/10.3390/polym7050939 - 13 May 2015
Cited by 71 | Viewed by 12019
Abstract
This study was dedicated to the blown film extrusion of poly(lactic acid), which mainly presents poor shear and elongation viscosities, and its blends. In order to enhance its melt strength, two main routes were selected (i) a structural modification through chain extension and [...] Read more.
This study was dedicated to the blown film extrusion of poly(lactic acid), which mainly presents poor shear and elongation viscosities, and its blends. In order to enhance its melt strength, two main routes were selected (i) a structural modification through chain extension and branching mechanisms by adding a reactive multifunctional epoxide (named Joncryl) and (ii) blending with poly(butylene adipate-co-terephtalate), named PBAT in presence (or not) of Joncryl. The effects of the reactive agent on the shear and elongation rheology, morphological, and interfacial properties of the blends were systematically investigated. A decrease of the interfacial tension has been also demonstrated according to the deformed drop retraction method (DDRM). Hence, the role of Joncryl as a compatibilizer was highlighted. Consequently, finer morphology of the dispersed phase was obtained. Furthermore, the impact of the two modification routes on the blown film extrusion ability of PLA has been studied. Based on the improved shear and elongational rheological properties, a great enlargement of the blowing processing window of PLA modified with Joncryl was demonstrated. Indeed, with the addition of Joncryl into PLA–PBAT blends, a reduction of the instability defects has been detected. Finally, the induced crystalline structure and the thermo-mechanical properties of blown films were shown to be improved. Full article
Show Figures

Figure 1

1411 KiB  
Article
Synthesis of β-cyclodextrin-Based Star Block Copolymers with Thermo-Responsive Behavior
by Agnes Wycisk, Artjom Döring, Martin Schneider, Monika Schönhoff and Dirk Kuckling
Polymers 2015, 7(5), 921-938; https://doi.org/10.3390/polym7050921 - 6 May 2015
Cited by 24 | Viewed by 9587
Abstract
Star polymers are one example of three-dimensional macromolecules containing several arms with similar molecular weight connected to a central core. Due to their compact structure and their enhanced segment density in comparison to linear polymers of the same molecular weight, they have attracted [...] Read more.
Star polymers are one example of three-dimensional macromolecules containing several arms with similar molecular weight connected to a central core. Due to their compact structure and their enhanced segment density in comparison to linear polymers of the same molecular weight, they have attracted significant attention during recent years. The preparation of block-arm star copolymers with a permanently hydrophilic block and an “environmentally” sensitive block, which can change its nature from hydrophilic to hydrophobic, leads to nanometer-sized responsive materials with unique properties. These polymers are able to undergo a conformational change or phase transition as a reply to an external stimulus resulting in the formation of core–shell nanoparticles, which further tend to aggregate. Star-shaped copolymers with different cores were synthesized via atom transfer radical polymerization (ATRP). The core-first method chosen as synthetic strategy allows good control over the polymer architecture. First of all the multifunctional initiators were prepared by esterification reaction of the hydroxyl groups with 2-chloropropionyl chloride. Using β-cyclodextrin as core molecules, which possess a well-defined number of functional groups up to 21, allows defining the number of arms per star polymer. In order to prepare stimuli-responsive multi-arm copolymers, containing a stimuli-responsive (poly(N-isopropylacrylamide) (PNIPAAm)) and a non-responsive block (poly(N,N-dimethylacrylamide) (PDMAAm)), consecutive ATRP was carried out. The polymers were characterized intensively using NMR spectroscopy and size exclusion chromatography (SEC), whereas the temperature-depending aggregation behavior in aqueous solution was determined via turbidimetry and differential scanning calorimetry (DSC). Full article
Show Figures

Graphical abstract

1668 KiB  
Article
Synthesis and Thermosensitive Behavior of Polyacrylamide Copolymers and Their Applications in Smart Textiles
by Tao Chen, Qisheng Fang, Qi Zhong, Yangyi Chen and Jiping Wang
Polymers 2015, 7(5), 909-920; https://doi.org/10.3390/polym7050909 - 6 May 2015
Cited by 44 | Viewed by 9027
Abstract
We tuned the lower critical solution temperature (LCST) of amphiphilic poly(N-isopropylacrylamide) (PNIPAAm) via copolymerization with a hydrophilic comonomer of N-hydroxymethyl acrylamide (NHMAAm). A series of copolymers P(NIPAAm-co-NHMAAm) were synthesized by atom transfer radical polymerization (ATRP) using CuBr/(N [...] Read more.
We tuned the lower critical solution temperature (LCST) of amphiphilic poly(N-isopropylacrylamide) (PNIPAAm) via copolymerization with a hydrophilic comonomer of N-hydroxymethyl acrylamide (NHMAAm). A series of copolymers P(NIPAAm-co-NHMAAm) were synthesized by atom transfer radical polymerization (ATRP) using CuBr/(N,N,N',N',N''-Pentamethyldiethylenetriamine) (PMDETA) as a catalyst system and 2-bromo ethyl isobutyrate (EBiB) as an initiator. The copolymers were well characterized by Fourier transform infrared spectroscopy (FT-IR), 1H Nuclear magnetic resonance (NMR), and Thermogravimetric analysis (TGA). The copolymers followed a simple rule in their thermosensitive behaviors and have a linear increase in the LCST as a function of NHMAAm mol%. The thermosensitive properties of the copolymer films were investigated and demonstrated hydrophilic-hydrophobic transitions. Finally, the copolymer was grafted onto cotton fabrics using citric acid (CA) as a crosslinking agent and sodium hypophosphite (SHP) as a catalyst following a two dipping, two padding process. The large number of hydroxyl groups in the copolymer makes grafting convenient and firm. The grafted cotton fabrics show obvious thermosensitive behaviors. The results demonstrate that the cotton fabrics become more hydrophobic when the temperature is higher than the LCST. This study presents a valuable route towards temperature-responsive smart textiles and their potential applications. Full article
Show Figures

Graphical abstract

4908 KiB  
Article
Synthesis and Characterization of [60]Fullerene-Glycidyl Azide Polymer and Its Thermal Decomposition
by Ting Huang, Bo Jin, Ru Fang Peng, Cong Di Chen, Rong Zong Zheng, Yi He and Shi Jin Chu
Polymers 2015, 7(5), 896-908; https://doi.org/10.3390/polym7050896 - 5 May 2015
Cited by 20 | Viewed by 11414
Abstract
A new functionalized [60]fullerene-glycidyl azide polymer (C60-GAP) was synthesized for the first time using a modified Bingel reaction of [60]fullerene (C60) and bromomalonic acid glycidyl azide polymer ester (BM-GAP). The product was characterized by Fourier transform infrared (FTIR), ultraviolet-visible [...] Read more.
A new functionalized [60]fullerene-glycidyl azide polymer (C60-GAP) was synthesized for the first time using a modified Bingel reaction of [60]fullerene (C60) and bromomalonic acid glycidyl azide polymer ester (BM-GAP). The product was characterized by Fourier transform infrared (FTIR), ultraviolet-visible (UV-Vis), and nuclear magnetic resonance spectroscopy (NMR) analyses. Results confirmed the successful preparation of C60-GAP. Moreover, the thermal decomposition of C60-GAP was analyzed by differential scanning calorimetry (DSC), thermogravimetric analysis coupled with infrared spectroscopy (TGA-IR), and in situ FTIR. C60-GAP decomposition showed a three-step thermal process. The first step was due to the reaction of the azide group and fullerene at approximately 150 °C. The second step was ascribed to the remainder decomposition of the GAP main chain and N-heterocyclic at approximately 240 °C. The final step was attributed to the burning decomposition of amorphous carbon and carbon cage at around 600 °C. Full article
Show Figures

Graphical abstract

6801 KiB  
Article
Residual Axial Capacity Comparison of CFFT and RC Bridge Columns after Fire
by Alicia Echevarria, Arash E. Zaghi, Richard Christenson and Rachel Plank
Polymers 2015, 7(5), 876-895; https://doi.org/10.3390/polym7050876 - 5 May 2015
Cited by 12 | Viewed by 8873
Abstract
The fire performance of protected concrete-filled fiber reinforced polymer (FRP) tube (CFFT) and conventional reinforced concrete (RC) bridge columns is studied through two phases of experimental research comprised of fire exposure and residual axial capacity tests. Two one-fifth scale CFFT columns and two [...] Read more.
The fire performance of protected concrete-filled fiber reinforced polymer (FRP) tube (CFFT) and conventional reinforced concrete (RC) bridge columns is studied through two phases of experimental research comprised of fire exposure and residual axial capacity tests. Two one-fifth scale CFFT columns and two one-fifth scale conventional RC columns having similar axial and flexural capacities were subjected to two durations of extreme temperature exposure. The CFFT columns were protected by the Tyfo® CFP fire protection system during the experiments. Subsequently, the post-fire robustness of the columns was quantified by measuring the residual axial capacity characteristics of each column. The protected CFFT columns exhibited superior axial strength and stiffness retention compared to the RC columns after fire exposure. Full article
(This article belongs to the Collection Fiber-Reinforced Polymer Composites in Structural Engineering)
Show Figures

Graphical abstract

1746 KiB  
Article
Compressive Behavior of Concrete Confined with GFRP Tubes and Steel Spirals
by Liang Huang, Xiaoxun Sun, Libo Yan and Deju Zhu
Polymers 2015, 7(5), 851-875; https://doi.org/10.3390/polym7050851 - 30 Apr 2015
Cited by 44 | Viewed by 8725
Abstract
This paper presents the experimental results and analytical modeling of the axial compressive behavior of concrete cylinders confined by both glass fiber-reinforced polymer (GFRP) tube and inner steel spiral reinforcement (SR). The concrete structure is termed as GFRP–SR confined concrete. The number of [...] Read more.
This paper presents the experimental results and analytical modeling of the axial compressive behavior of concrete cylinders confined by both glass fiber-reinforced polymer (GFRP) tube and inner steel spiral reinforcement (SR). The concrete structure is termed as GFRP–SR confined concrete. The number of GFRP layers (1, 2, and 3 layers) and volumetric ratios of SR (1.5% and 3%) were the experimental variables. Test results indicate that both GFRP tube and SR confinement remarkably increase the ultimate compressive strength, energy dissipation capacity, and ductility of concrete. The volumetric ratio of SR has a more pronounced influence on the energy dissipation capacity of confined concrete with more GFRP layers. In addition, a stress–strain model is presented to predict the axial compressive behavior of GFRP–SR confined concrete. Comparisons between the analytical results obtained using the proposed model and experimental results are also presented. Full article
(This article belongs to the Collection Fiber-Reinforced Polymer Composites in Structural Engineering)
Show Figures

Graphical abstract

1243 KiB  
Article
Addition of Zinc Improves the Physical Stability of Insulin in the Primary Emulsification Step of the Poly(lactide-co-glycolide) Microsphere Preparation Process
by Chandrasekar Manoharan and Jagdish Singh
Polymers 2015, 7(5), 836-850; https://doi.org/10.3390/polym7050836 - 28 Apr 2015
Cited by 10 | Viewed by 7434
Abstract
In this study, the effect of zinc on insulin stability during the primary emulsification step of poly(lactide-co-glycolide) microspheres preparation by the water-in-oil-in-water (w/o/w) double emulsion solvent evaporation technique was evaluated. Insulin was emulsified at homogenization speeds of 5000 and 10,000 rpm. [...] Read more.
In this study, the effect of zinc on insulin stability during the primary emulsification step of poly(lactide-co-glycolide) microspheres preparation by the water-in-oil-in-water (w/o/w) double emulsion solvent evaporation technique was evaluated. Insulin was emulsified at homogenization speeds of 5000 and 10,000 rpm. Insulin was extracted from the primary w/o emulsion by a method previously reported from our laboratory and analyzed by comprehensive analytical techniques. The differential scanning calorimetry thermograms of insulin with zinc showed a single peak around 83 °C with calorimetric enthalpy values similar to native insulin. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) of extracted insulin showed a single intense band around 6 kDa, demonstrating the preservation of primary structure. High performance liquid chromatography (HPLC) analysis revealed that no degradation products were formed during the homogenization process. Insulin aggregates residing at the w/o interfaces were found to be of non-covalent nature. In addition, observation of a single characteristic peak for insulin at m/z 5808 in the matrix-assisted laser desorption/ionization time-of-flight (MALDI-TOF) mass spectrum confirmed the absence of insulin degradation products and covalent dimers. Presence of zinc preserved the secondary structure of insulin as indicated by circular dichroism. In conclusion, these results show that with the addition of zinc, insulin stability can be improved during the primary emulsification step. Full article
(This article belongs to the Special Issue Polymers and Polymeric Nanoparticles for Therapy and Imaging)
Show Figures

Graphical abstract

1567 KiB  
Article
Modeling the Influence of Diffusion-Controlled Reactions and Residual Termination and Deactivation on the Rate and Control of Bulk ATRP at High Conversions
by Ali Mohammad Rabea and Shiping Zhu
Polymers 2015, 7(5), 819-835; https://doi.org/10.3390/polym7050819 - 28 Apr 2015
Cited by 36 | Viewed by 8047
Abstract
In high-conversion atom transfer radical polymerization (ATRP), all the reactions, such as radical termination, radical deactivation, dormant chain activation, monomer propagation, etc. could become diffusion controlled sooner or later, depending on relative diffusivities of the involved reacting species. These diffusion-controlled reactions directly affect [...] Read more.
In high-conversion atom transfer radical polymerization (ATRP), all the reactions, such as radical termination, radical deactivation, dormant chain activation, monomer propagation, etc. could become diffusion controlled sooner or later, depending on relative diffusivities of the involved reacting species. These diffusion-controlled reactions directly affect the rate of polymerization and the control of polymer molecular weight. A model is developed to investigate the influence of diffusion-controlled reactions on the high conversion ATRP kinetics. Model simulation reveals that diffusion-controlled termination slightly increases the rate, but it is the diffusion-controlled deactivation that causes auto-acceleration in the rate (“gel effect”) and loss of control. At high conversions, radical chains are “trapped” because of high molecular weight. However, radical centers can still migrate through (1) radical deactivation–activation cycles and (2) monomer propagation, which introduce “residual termination” reactions. It is found that the “residual termination” does not have much influence on the polymerization kinetics. The migration of radical centers through propagation can however facilitate catalytic deactivation of radicals, which improves the control of polymer molecular weight to some extent. Dormant chain activation and monomer propagation also become diffusion controlled and finally stop the polymerization when the system approaches its glass state. Full article
(This article belongs to the Special Issue Precision Polymer Synthesis)
Show Figures

Graphical abstract

1450 KiB  
Article
Photo-Crosslinking of Pendent Uracil Units Provides Supramolecular Hole Injection/Transport Conducting Polymers for Highly Efficient Light-Emitting Diodes
by Hsi-Kang Shih, Yi-Han Chen, Yu-Lin Chu, Chih-Chia Cheng, Feng-Chih Chang, Chao-Yuan Zhu and Shiao-Wei Kuo
Polymers 2015, 7(5), 804-818; https://doi.org/10.3390/polym7050804 - 27 Apr 2015
Cited by 30 | Viewed by 7664
Abstract
A new process for modifying a polymeric material for use as a hole injection transport layer in organic light-emitting diodes has been studied, which is through 2π + 2π photodimerization of a DNA-mimetic π-conjugated poly(triphenylamine-carbazole) presenting pendent uracil groups (PTC-U) under 1 h [...] Read more.
A new process for modifying a polymeric material for use as a hole injection transport layer in organic light-emitting diodes has been studied, which is through 2π + 2π photodimerization of a DNA-mimetic π-conjugated poly(triphenylamine-carbazole) presenting pendent uracil groups (PTC-U) under 1 h of UV irradiation. Multilayer florescence OLED (Organic light-emitting diodes) device with the PTC-U-1hr as a hole injection/transport layer (ITO (Indium tin oxide)/HITL (hole-injection/transport layer) (15 nm)/N,N'-di(1-naphthyl)- N,N'-diphenyl-(1,1'-biphenyl)-4,4'-diamine (NPB) (15 nm)/Tris-(8-hydroxyquinoline) aluminum (Alq3) (60 nm)/LiF (1 nm)/Al (100 nm)) is fabricated, a remarkable improvement in performance (Qmax (external quantum efficiency) = 2.65%, Bmax (maximum brightness) = 56,704 cd/m2, and LE (luminance efficiency)max = 8.9 cd/A) relative to the control PTC-U (Qmax = 2.40%, Bmax = 40,490 cd/m2, and LEmax = 8.0 cd/A). Multilayer phosphorescence OLED device with the PTC-U-1hr as a hole injection/transport layer (ITO/HITL (15 nm)/Ir(ppy)3:PVK (40 nm)/BCP (10nm)/Alq3 (40 nm)/LiF (1 nm)/Al (100 nm)) is fabricated by successive spin-coating processes, a remarkable improvement in performance (Qmax = 9.68%, Bmax = 41,466 cd/m2, and LEmax = 36.6 cd/A) relative to the control PTC-U (Qmax = 8.35%, Bmax = 34,978 cd/m2, and LEmax = 30.8 cd/A) and the commercial product (poly(3,4-ethylenedioxythiophene):polystyrenesulfonate) PEDOT:PSS (Qmax = 4.29%, Bmax = 15,678 cd/m2, and LEmax = 16.2 cd/A) has been achieved. Full article
Show Figures

Graphical abstract

3825 KiB  
Review
Methylcellulose, a Cellulose Derivative with Original Physical Properties and Extended Applications
by Pauline L. Nasatto, Frédéric Pignon, Joana L. M. Silveira, Maria Eugênia R. Duarte, Miguel D. Noseda and Marguerite Rinaudo
Polymers 2015, 7(5), 777-803; https://doi.org/10.3390/polym7050777 - 24 Apr 2015
Cited by 365 | Viewed by 34335
Abstract
This review covers the preparation, characterization, properties, and applications of methylcelluloses (MC). In particular, the influence of different chemical modifications of cellulose (under both heterogeneous and homogeneous conditions) is discussed in relation to the physical properties (solubility, gelation) of the methylcelluloses. The molecular [...] Read more.
This review covers the preparation, characterization, properties, and applications of methylcelluloses (MC). In particular, the influence of different chemical modifications of cellulose (under both heterogeneous and homogeneous conditions) is discussed in relation to the physical properties (solubility, gelation) of the methylcelluloses. The molecular weight (MW) obtained from the viscosity is presented together with the nuclear magnetic resonance (NMR) analysis required for the determination of the degree of methylation. The influence of the molecular weight on the main physical properties of methylcellulose in aqueous solution is analyzed. The interfacial properties are examined together with thermogelation. The surface tension and adsorption at interfaces are described: surface tension in aqueous solution is independent of molecular weight but the adsorption at the solid interface depends on the MW, the higher the MW the thicker the polymeric layer adsorbed. The two-step mechanism of gelation is confirmed and it is shown that the elastic moduli of high temperature gels are not dependent on the molecular weight but only on polymer concentration. Finally, the main applications of MC are listed showing the broad range of applications of these water soluble cellulose derivatives. Full article
(This article belongs to the Collection Polysaccharides)
Show Figures

Graphical abstract

Previous Issue
Next Issue
Back to TopTop