Perovskite Nanomaterials: Fabrication, Devices and Applications

A special issue of Micromachines (ISSN 2072-666X). This special issue belongs to the section "D:Materials and Processing".

Deadline for manuscript submissions: closed (15 October 2018) | Viewed by 9174

Special Issue Editor

Davidson School of Chemical Engineering, Purdue University, West Lafayette, IN, USA
Interests: organic electronics; nano materials and nano electronics; hybrid materials; perovskites

Special Issue Information

Dear Colleagues,

Over the past few years, there has been tremendous progress in the development of halide perovskites semiconducting materials for high-efficiency photovoltaic devices. Particularly, beyond the bulk polycrystalline perovskite thin films, nano scale halide perovskites (e.g., zero-dimensional quantum dots, one-dimensional nanowires and two-dimensional sheets) provide new opportunities to tune the materials’ optical, electronic, and mechanical properties for a variety of applications. In this Special Issue, we address the remaining challenges to be resolved, so as to achieve a better understanding of the materials structure–property relationship, as well as new applications for next generation solar cells, light emitting diodes, sensors, nano electronics and nano photonics. In this pioneering Special Issue, we discuss the synthesis and morphology control of perovskite nanostructures, the characterization of their unique properties, and the assembly and device applications of such exciting new materials. Contributions from science and engineering community highlight interesting new discoveries and new research directions, which would excite more future studies and inspire new ideas.

Dr. Letian Dou
Guest Editor

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Micromachines is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Halide Perovskite
  • Nano materials
  • Nano electronics
  • Nano photonics
  • Flexible devices

Published Papers (2 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

7 pages, 10973 KiB  
Article
Outstanding Photoluminescence in Pr3+-Doped Perovskite Ceramics
by Jiameng Zhang, Yanan Hao, Meihua Bi, Guoyan Dong, Xiaoming Liu and Ke Bi
Micromachines 2018, 9(9), 419; https://doi.org/10.3390/mi9090419 - 21 Aug 2018
Cited by 4 | Viewed by 2964
Abstract
Ba (Zr0.2Ti0.8) O3-50% (Ba0.7Ca0.3) TiO3 (BZT-0.5BCT) ceramics with different doping contents of Pr3+ were prepared by the conventional solid-state reaction. The phase structure and crystallinity of the fabricated ceramics were investigated [...] Read more.
Ba (Zr0.2Ti0.8) O3-50% (Ba0.7Ca0.3) TiO3 (BZT-0.5BCT) ceramics with different doping contents of Pr3+ were prepared by the conventional solid-state reaction. The phase structure and crystallinity of the fabricated ceramics were investigated by X-ray diffraction, Raman spectroscopy, and scanning electron microscopy. Photoluminescence (PL) emission spectra were measured to analyze the PL characteristics. The strong intensities of a green band at 489 nm and a red band at 610 nm were observed. The maximum emission intensity of the PL spectrum was achieved in the BZT-0.5BCT ceramic with 0.2% mol of Pr3+ ions. Furthermore, the PL spectra of BZT-0.5BCT ceramics were found to be sensitive to polarization of the ferroelectric ceramics. Compared with the unpoled ceramics, the green emission increased about 42% and a new emission peak at 430 nm appeared for the poled ceramics. With excellent intrinsic ferroelectricity and an enhanced PL property, such material has potential to realize multifunctionality in a wide application range. Full article
(This article belongs to the Special Issue Perovskite Nanomaterials: Fabrication, Devices and Applications)
Show Figures

Figure 1

8 pages, 3329 KiB  
Article
Preparation and Characteristics of MAPbBr3 Perovskite Quantum Dots on NiOx Film and Application for High Transparent Solar Cells
by Lung-Chien Chen, Kuan-Lin Lee, Chun-Yuan Huang, Jia-Ching Lin and Zong-Liang Tseng
Micromachines 2018, 9(5), 205; https://doi.org/10.3390/mi9050205 - 27 Apr 2018
Cited by 17 | Viewed by 5913
Abstract
In this work, a MAPbBr3 quantum dot (QD-MAPbBr3) layer was prepared by a simple and rapid method. Octylammonium bromide (OABr) gives the MAPbBr3 better exciton binding energy, good surface morphology, and stability. To form a nanocrystalline thin film on [...] Read more.
In this work, a MAPbBr3 quantum dot (QD-MAPbBr3) layer was prepared by a simple and rapid method. Octylammonium bromide (OABr) gives the MAPbBr3 better exciton binding energy, good surface morphology, and stability. To form a nanocrystalline thin film on indium tin oxide (ITO) glass, the QD-MAPbBr3 film was coated by a spin-coating method in a nitrogen-filled glove box and the NiOx film was used as an adhesive layer and hole transport layer. The highest transmittance of MAPbBr3 on NiOx/ITO glass was around 75% at 700 nm. This study also reported a high transparent and perovskite bulk-free ITO/NiOx/QD-MAPbBr3/C60/Ag solar cell where the NiOx, QD-MAPbBr3, and C60 were used as a hole transport layer, active layer, and electron transport layer, respectively. Full article
(This article belongs to the Special Issue Perovskite Nanomaterials: Fabrication, Devices and Applications)
Show Figures

Figure 1

Back to TopTop